ATEN CS1316KIT User manual

KVM Switch

CS1308 / CS1316

User Manual

www.aten.com

CS1308 / CS1316 User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

CE Warning: This is a class A product. In a domestic environment this

product may cause radio interference in which case the user may be required to

take adequate measures.

KCC Statement

유선 제품용 / A 급 기기 ( 업무용 방송 통신 기기 )

이 기기는 업무용 (A 급) 전자파적합기기로서 판매자 또는 사용자는 이

점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적으로

합니다 .

RoHS

This product is RoHS compliant.

CS1308 / CS1316 User Manual

iii

SJ/T 11364-2006

The following contains information that relates to China.

CS1308 / CS1316 User Manual

iv

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-10-5255-0110

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

United Kingdom 44-8-4481-58923

CS1308 / CS1316 User Manual

v

Package Contents

The CS1308 / CS1316 package consists of:

1 CS1308 / CS1316 KVM Switch with Rack Mount Kit

1 Console cable

1 Firmware Upgrade cable

1 Foot Pad set (4 pads)

1 Power Adapter (AC Models)

1 User Instructions*

Check to make sure that all the components are present and that nothing got

damaged in shipping. If you encounter a problem, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit, and/or any of the

devices connected to it.

*Features may have been added to the CS1308 / CS1316 since this manual

was published. Please visit our website to download the most up-to-date

version of the manual.

Manual Part No. PAPE-0305-AT4G

F/W Version: V1.0.072

Manual Date: 2015-08-19

All other brand names and trademarks are the registered property of their respective owners.

CS1308 / CS1316 User Manual

vi

Contents

EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

SJ/T 11364-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

About this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Chapter 1.

Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 2.

Hardware Setup

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Rack Mounting – Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Rack Mounting – Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Single Level Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Cable Connection Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Two Level Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 3.

Basic Operation

Hot Plugging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Hot Plugging Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

CS1308 / CS1316 User Manual

vii

Manual Port Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Powering Off and Restarting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Chapter 4.

OSD Operation

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Manufacturing Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

OSD Login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

OSD Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

OSD Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

OSD Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

F2: LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

F3: SET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

F5: SKP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

F6: BRC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

F8: LOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Chapter 5.

Keyboard Port Operation

Hotkey Port Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Invoke Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Number Lock and Minus Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Control and F12 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Select the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Auto Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Invoking Auto Scan: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Skip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Computer Keyboard / Mouse Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Hotkey Beeper Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Quick Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

OSD Hotkey Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Port OS Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Restore Default Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Hotkey Summary Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Chapter 6.

Keyboard Emulation

Mac Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Sun Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Chapter 7.

CS1308 / CS1316 User Manual

viii

The Firmware Upgrade Utility

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . . 41

Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Starting the Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Upgrade Succeeded. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Upgrade Failed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Appendix

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

CS1308 to Compatible 8-Port Switches . . . . . . . . . . . . . . . . . . . . . . . 52

CS1308 to Compatible 16-Port Switches . . . . . . . . . . . . . . . . . . . . . . 52

CS1316 to Compatible 8-Port Switches . . . . . . . . . . . . . . . . . . . . . . . 52

CS1316 to Compatible 16-Port Switches . . . . . . . . . . . . . . . . . . . . . . 52

Supported KVM Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Restoring Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

OSD Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

About SPHD Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

CS1308 / CS1316 User Manual

ix

About this Manual

This user manual is provided to help you get the most from your CS1308 /

CS1316 system. It covers all aspects of installation, configuration and

operation. An overview of the information found in the manual is provided

below.

Chapter 1, Introduction, introduces you to the CS1308 / CS1316 system.

Its purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Hardware Setup, describes how to set up your installation. The

necessary steps – from a basic single level hookup to a complete 17-switch two

level operation are provided.

Chapter 3, Basic Operation, explains the fundamental concepts involved

in operating the CS1308 / CS1316.

Chapter 4, OSD Operation, provides a complete description of the

CS1308 / CS1316 OSD (on-screen display), and how to work with it.

Chapter 5, Keyboard Port Operation, details all of the concepts and

procedures involved in the hotkey operation of your CS1308 / CS1316

installation.

Chapter 6, Keyboard Emulation, provides tables that list the PC to Mac

and PC to Sun keyboard emulation mappings.

Chapter 7, The Firmware Upgrade Utility, explains how to use this

utility to upgrade the CS1308 / CS1316 firmware with the latest available

versions.

An Appendix, provides specifications and other technical information

regarding the CS1308 / CS1316.

CS1308 / CS1316 User Manual

x

Conventions

This manual uses the following conventions:

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦Bullet lists provide information, but do not involve sequential steps.

→Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start → Run means to

open the Start menu, and then select Run.

Indicates critical information.

International http://www.aten.com

North America http://www.aten-usa.com

1

Chapter 1

Introduction

Overview

The CS1308 / CS1316 KVM switch allows access and control up to 256

computers from a single console (keyboard, mouse, and monitor). As many as

16 additional switches can be cascaded bringing the total number of connected

computers to 256 computers that can be controlled from a single keyboard-

monitor-mouse console. Additionally, the CS1308 / CS1316 features a

compact design that allows installation in a 1U system rack.

Setup is fast and easy; plugging cables into their appropriate ports is all that is

needed. The switch supports both USB and PS/2 connections for the console

and computers. The CS1308 / CS1316 intercepts keyboard input directly, thus

eliminating the need for any software configuration. Switching between

computers can be easily accomplished either by manually pressing the front

panel push button port LEDs, entering hotkey combinations from the

keyboard, or via a menu driven multilingual on-screen display (OSD) system.

A convenient auto-scan feature permits automatic scanning and monitoring of

activities on all connected computers. Lastly, the CS1308 / CS1316 offers

benefits such as: a) managing multiple computers from a single console, b)

eliminating the expense of having to purchase a separate keyboard, monitor,

and mouse for each computer, c) space and energy costs savings, and d)

helping create a greener environment by reducing the amount of waste.

CS1308 / CS1316 User Manual

2

Features

A single console controls up to 256 computers

Cascade to 2 levels – connect up to 16 switches

Dual Interface – supports computers with PS/2 or USB keyboards and

mice

Multiplatform support – Windows 2000/XP/Vista, Linux, Mac, and Sun

Supports USB keyboards for PC, Mac and Sun

Auto PS/2 and USB interface detection

USB or PS/2 keyboard and mouse emulation – computers boot even when

the console focus is elsewhere

Superior video quality – up to 2048 x 1536; DDC2B

Convenient computer switching via front panel pushbuttons, hotkeys, or

multilingual on-screen display (OSD) menu

Two level password security - only authorized users view and control

computers; up to four users and an administrator with a separate profile for

each

Auto Scan feature for monitoring user-selected computers

Broadcast mode – operations simultaneously performed on all selected

computers

Hot pluggable – add or remove computers without having to power down

the switch

Buzzer on/off via hotkey and OSD

Firmware upgradeable

No software installation required

Designed for desktop or rack mount (19” system rack, 1U)

Chapter 1. Introduction

3

Requirements

Console

The following hardware components are required for the KVM console:

A VGA, SVGA, or multisync monitor capable of displaying the highest

resolution provided by any computer in the installation.

A keyboard and mouse (USB or PS/2)

Computers

The following hardware components are required for each computer:

A VGA, SVGA, or multisync video graphics card with an HDB-15 port.

PS/2 mouse and keyboard ports (6-pin Mini-DIN), at least one USB port.

Cables

Substandard cables might damage the connected devices or degrade overall

performance. For optimum signal integrity and to simplify the layout use the

high quality custom cable sets described below.

Function Length Part Number

KVM switch to computer PS/2 1.2 m

1.8 m

3.0 m

6.0 m

1.8 m

2L-5201P

2L-5202P

2L-5203P

2L-5206P

2L-5702P

USB 1.2 m

1.8 m

3.0 m

5.0 m

2L-5201U

2L-5202U

2L-5203U

2L-5205U

CS1308 / CS1316 User Manual

4

Operating Systems

Supported operating systems are shown in the table, below:

OS Version

Windows 2000 and higher

Linux RedHat 7.1 and higher

SuSE 8.2 and higher

Mandriva (Mandrake) 9.0 and higher

UNIX AIX 4.3 and higher

FreeBSD 4.2 and higher

Sun Solaris 8 and higher

Novell Netware 5.0 and higher

Mac OS 9 and higher

Chapter 1. Introduction

5

Components

Front View

Note: The CS1316 is pictured above. The CS1308 / CS1308D front panel is the

same as the CS1316, except that it has 8 KVM port LEDs instead of 16.

No. Component Description

1 Port LEDs These port selection pushbuttons each contain 2 LEDs.

An orange LED indicates that a computer is connected to

the corresponding port.

A green LED indicates that the computer connected to the

corresponding port has focus.

Simultaneously pressing port LEDs 1 & 2 resets the

console keyboard and mouse.

Simultaneously pressing port LEDs 7 & 8 on the CS1308 /

CS1308D, or 15 & 16 on the CS1316, starts Auto Scan

mode. See F7: SCAN, page 29.

2 Reset Button Pressing in this button performs a system reset. When the

system is reset, the CS1308 / CS1316 beeps, and then the

KVM port LEDs flash in succession until the reset is

completed. After the reset is completed you can login again.

Note: This button is semi-recessed and must be pushed with a

small object, such as the end of a paper clip or a ballpoint pen.

3 Firmware

Upgrade

Recovery

Switch

During normal operation and while performing a firmware

upgrade, this switch should be in the NORMAL position. If a

firmware upgrade operation does not complete successfully,

this switch is used to perform a firmware upgrade recovery.

See Firmware Upgrade Recovery, page 46, for details.

4 Firmware

Upgrade Port The firmware upgrade cable that transfers the firmware

upgrade data from the administrator's computer to the

CS1308 / CS1316, plugs into this RJ-11 connector.

5 Power LED Lights to indicate that the unit is receiving power.

12 345

CS1308 / CS1316 User Manual

6

Rear View

Note: The CS1316 is pictured above. The CS1308 rear panel is the same as

the CS1316, except that it has 8 KVM ports instead of 16.

No. Component Description

1 Cable Tie Slot If you want to use a cable tie to gather the cables

together, you can run it through this slot to attach it to

the unit.

2 KVM Ports The cables that link to the computers plug in here.

Note: The shape of these 15-pin connectors has been

specifically modified so that only custom KVM cables

designed to work with this switch can plug in.

(See Cables, page 3, for details.) Do NOT attempt to

use ordinary 15-pin VGA connector cables to link

these ports to the computers.

3 Grounding Terminal The grounding wire used to ground the CS1308 /

CS1316 attaches here.

4 Power Jack The power adapter cable plugs in here.

5 Console Port The custom console cable set that is provided to

attach the console monitor, keyboard, and mouse

plugs in here.

12

34 5

7

Chapter 2

Hardware Setup

Overview

The CS1308 / CS1316 is a combo switch designed to work with USB and PS/

2 interfaces. It utilizes custom KVM cables that serve as intermediaries

between the switch and the connected computers. A separate custom KVM

cable is required for each computer connection. Custom cables of various

lengths are listed in the Cables section on page 5. Consult your dealer to find

out which one fit your needs best.

Before You Begin

1. Important safety information regarding the placement of this

device is provided on page 47. Please review it before proceeding.

2. Make sure that the power to any device that you connect to the

installation has been turned off. You must unplug the power cords

of any computers that have the Keyboard Power On function.

CS1308 / CS1316 User Manual

8

Stacking and Rack Mounting

The CS1308 / CS1316 can be stacked on a desktop or rack mounted in 1U of

rack space. The procedures are described in the following sections.

Note: 1. Allow at least 5.1 cm on each side for adequate ventilation and

12.7 cm at the rear for power cord and cable clearance.

2. The rack mount kit does not include cage nuts. If you need additional

screws or cage nuts, contact your rack dealer.

3. For instructional purposes, the CS1316 is pictured in the diagrams

that follow. However, the CS1308 is the same as the CS1316, except

that it has 8 KVM ports instead of 16.

Stacking

The CS1308 / CS1316 can be placed on any level surface that can safely

support its weight and the weight of the attached cables. Ensure that the surface

is clean and free of materials that can block the exhaust vents or otherwise

interfere with normal operation of the KVM switch. Peel the protective backing

off of the foot pads, and affix them to the bottom panel of the CS1308 / CS1316

at the corners, as shown in the diagram below.

Chapter 2. Hardware Setup

9

Rack Mounting – Front

1. Remove the screws from the left and right side panels near the front of the

switch (2 screws total).

2. Use the M3 x 8 Phillips hex head screws supplied with the rack mount kit

to screw the rack mounting brackets onto the side panels near the front of

the unit.

(Continues on next page.)

CS1308 / CS1316 User Manual

10

(Continued from previous page.)

3. Place the CS1308 / CS1316 in the rack. Position it so that the holes in the

mounting brackets line up with the holes in the rack. Secure the mounting

brackets to the front of the rack.

Page is loading ...

ATEN CS1316KIT User manual

This manual is also suitable for

ATEN CS1316KIT User manual

Related papers

Other documents