Pottinger CAT NOVA 260 T CR Operating instructions
- Category
- Lawnmowers
- Type
- Operating instructions
This manual is also suitable for
/PERATOR@S MANUAL
GB
).3425#4)/.3 &/2 02/$5#4 $%,)6%29 0AGE
4RANSLATION OF THE ORIGINAL /PERATING -ANUAL
Ihre / Your / Votre • Masch.Nr. • Fgst.Ident.Nr.
.R
CAT NOVA 260 T ED
(Type PSM 352 : +..01001)
99 352.GB.80I.0
Disc mower
ALLG./BA SEITE 2 / 0000-GB
Important information concerning Product
Liability.
According to the laws governing product liability, the manufacturer and dealer are obliged to hand the
operating manual to the customer at the time of sale, and to instruct them in the recommended operating,
safety, and maintenance regulations. Confirmation is necessary to prove that the machine and operating
manual have been handed over accordingly.
For this purpose,
- document A is to be signed and sent to Pöttinger,
- document B remains with the dealer supplying the machine,
- and the customer receives document C.
In accordance with the laws of product liability, every farmer is an entrepreneur.
According to the laws of product liability, property damage is damage caused by a machine and not to
it. An excess of Euro 500 is provided for such a liabilioty.
In accordance with the laws of product liability, entrepreneurial property damages are excluded from
the liability.
Attention! Should the customer resell the machine at a later date, the operating manual must be given
to the new owner who must then be instructed in the recommended regulations referred to herein.
GB Dear Farmer
You have just made an excellent choice. Naturally we are very happy
and wish to congratulate you for having chosen Pöttinger. As your
agricultural partner, we offer you quality and efficiency combined with
reliable servicing.
In order to assess the spare-parts demand for our agricultural machines
and to take these demands into consideration when developing new
machines, we would ask you to provide us with some details.
Furthermore, we will also be able to inform you of new developments.
Dokument D
GB-0600 Dokum D Anbaugeräte
PÖTTINGER Landtechnik GmbH
Industriegelände 1
A-4710 Grieskirchen
Tel. 07248 / 600 -0
Telefax 07248 / 600-2511
T Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating
devices at hand.
T Operation and maintenance of machine and/or implement according to operating instructions explained to the customer.
T Tyres checked re. correct pressure.
T Wheel nuts checked re. tightness.
T Drive shaft cut to correct lenght.
T *VYYLJ[WV^LY[HRLVɈZWLLKPUKPJH[LK
T Fitting to tractor carried out: to three-point linkage
T Trial run carried out and no defects found.
T Functions explained during trial run.
T Pivoting in transporting and operating position explained.
T Information given re. optional extras.
T Absolute need to read the operating manual indicated.
Please check. X
According to the product liability please check the above mentioned items.
INSTRUCTIONS FOR
PRODUCT DELIVERY
GB
In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.
For this purpose please do the following:
- sign the document A and send it to the company Pöttinger or via the internet to www.poettinger.at
- document B stays with the specialist factory delivering the machine.
- document C stays with the customer.
- 4 -
GB
0800_GB-Inhalt_352
TABLE OF CONTENTS
Attention!
ÈÛìÞëïÞÌÚßÞíò
ÁâçíìâçíáÞ
ìîééåÞæÞçí
ÍÚÛåÞèßÜèçíÞçíì
WARNING SIGNS
CE sign ............................................................................................................................................................................. 5
Meanings of warning signs............................................................................................................................................... 5
ATTACHMENT
Attaching the machine ..................................................................................................................................................... 6
Connecting the hydraulics ................................................................................................................................................ 6
Connecting the electrics................................................................................................................................................... 6
Check driving motor speed ............................................................................................................................................. 7
Correct drive shaft ............................................................................................................................................................ 7
Drive shaft length ............................................................................................................................................................. 7
TRANSPORT
Changing from work to transport position ....................................................................................................................... 8
Transporting on public roads ............................................................................................................................................ 8
Transporting on trailer or lorry .......................................................................................................................................... 8
OPERATION
Important points before starting work .............................................................................................................................. 9
Caution when turning on slopes! .................................................................................................................................... 10
Adjusting the machine .................................................................................................................................................... 10
Adjusting the machine ................................................................................................................................................... 11
Changing from transport to work position ..................................................................................................................... 13
Long swath board .......................................................................................................................................................... 14
Placing out of service ..................................................................................................................................................... 15
Swath formation to the side ........................................................................................................................................... 16
Adjusting swath board.................................................................................................................................................... 16
Electrohydraulic operation.............................................................................................................................................. 16
Variation "Extra dry" system ........................................................................................................................................... 17
MAINTENANCE
Safety point .................................................................................................................................................................... 18
General maintenance hints ............................................................................................................................................. 18
Cleaning of machine parts ............................................................................................................................................. 18
Parking in the ope .......................................................................................................................................................... 18
Winter storage ................................................................................................................................................................ 18
Drive shafts ..................................................................................................................................................................... 18
Hydraulic unit ................................................................................................................................................................. 18
Roller-type conditioner ................................................................................................................................................... 19
Every 50 hours of operation ........................................................................................................................................... 20
Cutter bar-oil change ...................................................................................................................................................... 20
Gearing ........................................................................................................................................................................... 21
Starting transmission ...................................................................................................................................................... 21
Garaging ......................................................................................................................................................................... 22
Lubrication chart ........................................................................................................................................................... 25
TECHNICAL DATA
Technical data ................................................................................................................................................................ 28
Defined use of the mower .............................................................................................................................................. 28
Position of Vehicle Identification Plate ........................................................................................................................... 28
SUPPLEMENT
Recommendations for work safety ............................................................................................................................... 31
Driveshaft ....................................................................................................................................................................... 32
Lubricants ....................................................................................................................................................................... 34
Air pressure ................................................................................................................................................................... 36
Taper bushes installation instructions ............................................................................................................................ 37
Turn gearing round ......................................................................................................................................................... 38
Power supply .................................................................................................................................................................. 40
Installation of control panel ........................................................................................................................................... 40
- 5 -
GB
кËÇÂÇÀÌÂÀÇÌ
0400_D-Warnbilder_353
The CE sign, which is affixed by the manufacturer,
indicates outwardly that this machine conforms to the
engineering guideline regulations and the other relevant
EU guidelines.
EU Declaration of Conformity (see Supplement).
By signing the EU Declaration of Conformity, the ma-
nufacturer declares that the machine being brought
into service complies with all relevant safety and health
requirements.
¼¾ìâàç
ÆÞÚçâçàìèßðÚëçâçàìâàçì
Before maintenance and repair work,
switch motor off and remove key.
Keep away from running motor with
p.t.o. connected.
bsb 447 410
Danger - flying objects; keep safe dis-
tance from the machine as long as the
engine is running.
Do not touch any moving parts.
Wait for complete standstill.
ËÞÜèææÞçÝÚíâèçì
ßèëðèëäìÚßÞíò
ºååéèâçíìëÞßÞëâçà
íèìÚßÞíòâçíáâì
æÚçîÚåÚëÞ
âçÝâÜÚíÞÝÛòíáâì
ìâàç§
- 6 -
GB
0000_GB-Anbau_353
ºííÚÜáâçàíáÞæÚÜáâçÞ
ÌÞÜîëÞåèðÞëáòÝëÚîåâÜåâçä¡Î¢ìèíáÚíâæéåÞæÞçíÜÚççèí
ìðâçàèîíìâÝÞðÚòì§
¦ ºàÚâçìíîçìíÞÚÝò¥îçìíÚÛåÞæÚÜáâçÞÚßíÞë¦ëîç
- Starting position:
Park machine on the support stand (7) on level
ground with bolts (8) inserted and spring pin
(10) secured.
- Attach lower link to the pipe bottom (9) and lock
at this height:
The attaching height corresponds to the parking
height on firm ground.
Fold support wheel (7) up: Pos. O
- Pin jack stand (7) up using bolts (8) and secure
with spring pin (10).
7
9
O
U
TD24/95/3
10
62-00-14
Important
Č ÌÚßÞíò
ÚÝïâÜÞ³ìÞÞ
ÌîééåÞæÞçíºª¥
éèâçí쪦±§
Č ¼áÞÜä
íáÚíÜîííÞëìÜëÞðì
ÚçÝéëèÜÞììèë
íâçÞìÚëÞßâëæåò
ìÞÚíÞݧ
¼èççÞÜíâçàíáÞáòÝëÚîåâÜì
- At least one double-action (11) and
- one single-action (10)
hydraulic connection must be available on the
tractor.
- Connect hydraulic lines to tractor:
- Feed hydraulic lines through cable routing
(13).
- Insert plug-in connections of hydraulic lines.
¼èççÞÜíâçàíáÞÞåÞÜíëâÜì
- Feed cable through cable routing (13).
- Connect.
Electrical equipment: see Supplement
ºÍͺ¼ÁƾÇÍ
- 7 -
GB
0000_GB-Anbau_353
ºÍͺ¼ÁƾÇÍ
½ëâïÞìáÚßíåÞçàíá
¼áÞÜäÝëâïÞìáÚßíåÞçàíáÛÞßèëÞâçâíâÚåèéÞëÚíâèçÚçÝÚÝÚéíâß
çÞÜÞììÚëò§ÌÞÞÜáÚéíÞëĎ½ËÂϾÌÁº¿ÍāÚåìèâçÌîééåÞæÞçí
»¥èëíáÞÚÜÜèæéÚçòâçàÝëâïÞìáÚßíâçìíëîÜíâèçæÚçîÚå§
W 2400
1000 rpm
W 2500
540 rpm
TD 47/96/9
¼èëëÞÜíÝëâïÞìáÚßí
Use correct drive shaft
• Type W 2500 for a drive motor speed of 540 rpm
• Type W 2400 for a drive motor speed of 1000 rpm
ÇèíÞ
ÌÞÞÜáÚéíÞë
Ď½ËÂϾÌÁº¿Íā
Úåìèâç
ÌîééåÞæÞçí»§
¼áÞÜäÝëâïâçàæèíèëìéÞÞÝ
(at the tractor)
1000 rpm = standard driving motor speed
The pivoting gear (SG) has been factory set for
operation with this rpm (delivery
condition).
540 rpm
When only this driving motor speed
(540 rpm) is possible on the tractor,
the gear (SG) must be removed and
installed again in reverse.
• Ensure the drawbar is
well supported (e. g. with a solid wooden block
"H")!
• Pemove oil filler neck.
• Then install protective cap again.
¿èëßîëíáÞëÝÞíÚâåììÞÞÜáÚéíÞë˾ϾËÌÂÇÀÍÁ¾À¾ºË
âçíáÞìîééåÞæÞçí§
TD8/95/6a
1000 rpm
540 rpm
SG
S
H
TD24/95/47
GB
- 8 -
0000_GB-TRANSPORTSTELLUNG_353
TRANSPORT
AT
TD24/95/18
4
Transporting on public roads
• Safety advice: see Supplement A1, pts. 1, 3, 4 and
6-9.
• Danger of injury can occur if machine swings out
during transportation.
- When travelling on public roads with machine swivelled in,
secure operating lever against swinging (E2).
• Travel on public roads only in transport position!
• Side guard rails (5):
- Remove linch pin (6).
- Fold guard rail up.
- Secure with linch pin.
• Check lighting and safety
equipment.
Changing from work to transport position
• Safety advice: see Supplement A1, pts. 1, 3, 4 and
6-9.
1. Before changing to transport position
- Turn p.t.o. off and wait for cutter to completely stop (mower
runs after turning off for approx. 30 seconds)
2. Raising the machine
- Raise mower: extend lifting cylinder (1) completely out.
• Lock (year of construction -1998)
- Remove spring pin (2).
- Fold locking device (3) up: Pos. O
- Secure with spring pin.
• Lock (year of construction +1999)
- Swing lever into position
T1
3. Swivelling the machine
in: Pos T
• Retract swivelling cylin-
der completely.
• Lock (year of construction
+1999)
- Swing lever into posi-
tion
E2
Transporting on trailer or lorry
- Fit in spacers (right 14,5 cm, left 11 cm).
- Swivel drawbar in and fix it (F).
U
O
1
23
TD24/95/16
TD 495.732
A1
T1
- 9 -
GB
0400_GB-Betreiben_353
OPERATION
Important points before starting work
After the first hours of operation
• Retighten all knife screw fittings.
1. Check
- The cutter condition and fixture
- The mower disc for damage (see chapter „Main-
tenance and Service“).
2. Only turn machine on when in work position
and do not exceed the stipulated p.t.o. r.p.m.
according to gearing fitted: 540 or 1000
r.p.m.!
• In principle, only turn p.t.o. on when all safety
equipment (covers, protective aprons, facings,
etc.) are in proper order and are in their protective
position on the implement.
3. Ensure the correct p.t.o. rotation direction! If
rotation direction is wrong then the drive runs
empty in the drive shaft free-running.
4. Damage protection!
• The surface to be mowed must be free of
obstructions or foreign objects. Such objects
(e.g. large stones, pieces of wood, boundary
stones, etc.) can damage the mower unit.
In the event of a collision
• Stop immediately and switch
off the drive.
• Carefully check the implement
for damage. The mowing discs
and their drive shaft must be
checked in particulare.
• Have the implement checked
also by a specialist workshop
if necessary.
After any contact with foreign objects
• Check the condition of knives and the knife holder.
• Retighten all knife screw fittings.
5. Keep away when motor is running
- Keep people out of the danger area as injury
can occur through out-thrown foreign bodies.
Take particular care on stoney fields, and near
roads and paths.
6. Wear hearing protection
The noise level in the working place can differ
from the measured values (see Technical Data),
particularly through the various designs of the
different tractor cabins.
• When a noise level of 85 dB(A) is reached or
exceeded, then the employer (farmer) must have
suitable hearing protection available (UVV 1.1
§2).
- When a noise level of 90 dB(A) is reached or
exceeded, then hearing protection must be worn
(UVV 1.1 § 16).
7. Check condition of V-belts
Replace worn out or damaged V-belts!
8. Check V-belt tension!
The disc on the pressure spring should be set at
the top control measurement. Adjustment takes
place by turning the adjusting nut accordingly.
Secure again with the locking nut afterwards (see
chapter "Maintenance and Service").
9. To mow, slowly throw-in the p.t.o. away from
the forage to be mowed and bring the mowing
drum up to full speed.
An even continuous increase in r.p.m. prevents
operating noises in the drive shaft free-running.
- The speed of travel depends on the terrain and
forage to be mowed.
bsb 447 410
TD 18/96/1
4a
Safety
advice:
see Supplement
A1, pts. 1-4 and
6-8.
OPERATION GB
0500-GB Einsatz_353 - 10 -
TD 58/98/08
1
510 mm
(Type: PSM 352)
515 mm
(Type: PSM 353)
520 mm
(Type: PSM 360)
550 mm
(Type: PTM 337)
L1
TD 58/98/09
R1
SK SK
38
L1 R1
(mm) (mm)
CAT 310 T (Type: PSM 337) 140 190
CAT NOVA 260 T (Type: PSM 352) 190 230
CAT NOVA 310 T (Type: PSM 353) 160 200
CAT NOVA 360 T (Type: PSM 360) 88 130
Adjusting the machine
(up to 2003 / 1 model)
1. Upper link relieving springs (1)
- Improve cutter unit adaption to ground contours.
- Are preset in the factory.
Inside measurement of the German rings
2. Adjust cutter bar bearing pressure on main
springs (38)
- Preset in the factory: 150 kg
- left: 75 kg
- right: 75 kg
Fixed measurement console spring:
- left: L1
- right: R1
- Decrease bearing pressure: turn screw (4) to the right.
- Increase bearing pressure: turn screw to the left.
Caution when turning on slopes!
Danger of tipping exists
- when turning left
- when mower unit is positioned downhill
Safety advice
• Mount accompanying ballast weights onto left wheel bearer of
mower unit (these components are optional with some types,
see Spare Parts List also)
• When turning left reduce speed accordingly.
• Travel with mower unit positioned uphill.
• It is better travel in reverse on a slope than to make a risky
turn.
OPERATION GB
0500-GB Einsatz_353 - 11 -
155-03-03
Adjusting the machine
(from 2003 / 2 model)
1. Adjust cutter bar bearing pressure on main
springs (3)
- Preset in the factory: 150 kg
- see table
2. Adjust skid bearing pressure at the spindle (4)
- Decrease bearing pressure: turn screw (4) to the right.
- Increase bearing pressure: turn screw to the left.
OPERATION GB
0500-GB Einsatz_353 - 12 -
90 cm
140 cm
024-95-32
13
12
TD24/95/33
15
+
-
+-
14
3. Adjusting swath width
- Loosen swath board (12) with clamping leaver
(13).
- Adjust swath board by shifting clamping lever.
- Secure.
4. Adjusting processor angle (Baujahr: - 1997)
• Turn lever (14) to the right. This brings impact plate
(15) closer to processor tines.
• Turn lever to the left. Impact plate is further away.
The distance between the impact plate and processor
tines can change the conditioning effect.
- Conditioning is most efficient in the lowest position
(-), the forage surface is intesively worn down but it
should not be beaten. Mais veiller à ne pas broyer
le fourrage.
- The opposite effect is the case for the highest po-
sition (+) as the forage surface is only lightly worn
down.
The correct setting depends on the volume of forage,
speed and tractor power among other things.
5. Adjusting processor angle (Baujahr: + 1998)
The gap between the beating arm and rotor is adjusted using the
hand lever.
Through this the processing effect can be changed.
• Processing is most effective in lowest position (5) where
forage surface is strongly reamed. But forage should not be
crushed.
• The opposite occurs in the uppermost position (0) where forage
is only lightly reamed.
The correct setting depends on the volume of forage, speed
and tractor power among other things. Therefore no references
necessary for the correct lever position can be given at this
point.
6. Altering rotor rpm
- by exchanging pulley
(A) and belts (B).
Parts: see Spare Parts
List
• 630 rpm
- pulley with ø 147 mm
This rpm is recommended for very leafy forage because it is
not intensively crushed.
• 860 rpm
- pulley with ø 197 mm
These prepare forage for quick drying. But forage should not
be crushed.
• 1000 rpm
- pulley with ø 224 mm
OPERATION GB
0300-GB Arbeitsstellung (353) - 13 -
10
10
9
9
TD24/95/29
AT
TD24/95/26
5
U
O
1
23
TD24/95/16
TD 495.732
A1
T1
Changing from transport to work position
• Danger of injury from out-swinging machine:
- Note free swivel area.
1. Swivel out
• Extend swivel cylinder (5) completely out: Pos. A
2. Lower machine
• Unlock on both sides (year of construction -1998):
- Remove spring pin (2).
- Fold locking mechanism (3) down: Pos. U
- Secure with spring pin.
• Unlock on both sides (year of construction +1999)
- Swing lever into position A1
3 Lower mower unit: retract lifting cylinder (1)
completely.
4. Folding down side guard rails (9) in work position
- Remove linch pin (10).
- Fold down guard rail.
OPERATION GB
0300-GB Arbeitsstellung (353) - 14 -
5. Adjusting cutting height
Setting: Lift mower unit hydraulically (H1)
• For optimum operation the set measurement for the telescopic
upper link should be 415-445 mm: see drawing (Type)
• Increase:
- Turn telescopic upper link (11) to the right.
• Decrease:
- Turn telescopic upper link to the left.
6. Adjust cutting height with runner
(only with CAT NOVA)
- The cutting height can be moved to 2 positions using
the runner (K)
- Pos. “A” low, pos. “B” high
SB-1
TD 62-00-25
SB
SB
62-00-26
Long swath board
The left standard swath board (SB) can be replaced by a longer
one (SB – 1).
By doing so the swath width (S1) can be reduced.
Problem:
In difficult working conditions (long, heavy grass) the longer swath
board (SB-1) may lead to clogging. In such a case the standard
swath board (SB) must be mounted.
OPERATION GB
0300-GB Arbeitsstellung (353) - 15 -
TD 23/95/41
s
h
0
ST
8
O
U
TD24/95/15
9
10
Electrics
- Pull out plug.
Hydraulics
- Disconnect hydraulic lines from tractor and insert into
holder.
Problems when uncoupling
- To reduce remaining pressure: position servo-valve briefly
at „lower (S)“.
- Uncouple hydraulic lines.
Disconnecting drive shaft
- Turn motor off.
- Turn p.t.o. off.
- Wait for standstill: The mowing unit runs for about 30
seconds after being shut off.
- Disconnect drive shaft
Uncouple lower link attachment.
Placing out of service
• Safety advice: see Supplement A1, pts. 1 and 8
- Park machine only on firm level ground.
Parking the machine
- Remove spring pin form support stand.
- Swing support stand (8) down and secure: Pos. U
Insert bolt (9) and secure with spring pin (10)
- Lower onto support stand using tractor’s hydraulics.
OPERATION GB
9800-GB SCHWAD (337) - 16 -
TD 47/96/2
TD 47/96/3
Zyl
TD 47/96/4
TD 26/92/48
s
h
0
ST
Swath formation to the side
• Danger of accident when swinging the machine out:
- Pay attention to free swivelling range.
- Crushing and cutting points within swivelling range of swatch
board.
Electrohydraulic operation
Control panel operation
- Pre-select required control panel
function (1)
- Actuate servo-valve (ST)
Swing drawbar
Swing draw-
bar and swath
board
Swing swath
board
Adjusting swath board
1. Swing drawbar out into working
position
2. Then actuate the servo-valve (ST)
- Swing swath board into position for
swath formation - right
- Lever in "RA" position
3. Move servo-valve (ST) to "LOWER"
(s)
- Swing swath board into position for swath formation
- left
- Lever in "LA" position
Changing to transport position
1. Pull rope (S)
2. Move servo-valve (ST) to
"LOWER" (s)
- Drawbar swings into transport
position
- Release rope (S)
Lever in
"TR" position
Swath formation - left
- Lever in "LA" position
Swath formation - right
- Lever in "RA" position
Tansport position
- Lever in "TR" position
- 17 -
GB
9800_GB-Exdra dry_352
OPERATION
Swathes
1. Set the positions of the guiding plates
- see diagram
Variation "Extra dry" system
Note
The settings listed
below are to be
understood as
basic settings.
Because of the
various types
of crops, an
optimum setting
of the guiding
plates can
possibly first be
ascertained when
the machine is in
use.
Spread width
1. Remove left rear swath plates (LH)
- remove truss-head screws (FL) and
level (H)
2. Fix left front swath plate (LV) with lever
(H)
3. Set the positions of the guiding plates
- see diagram
TD 58/98/02
TD 58/98/03
LH
LV
FL
H
- 18 -
GB
0400_GB-BA-Allg. Wartung
Parking in the ope
When parking in the open for
long periods of time, clean
piston rods and then coat
with grease.
FETT
Safety
points!
• Turn engine off
when adjustment,
service and repair
work is to be
done.
• Do not work un-
der the machine
without safe
support.
• Retighten all
screws after the
first hours of
operation..
General maintenance hints
In order to keep the implement in
good condition after long periods
of operation, please observe the
following points:
- Tighten all screws after the first
hours of operation.
In particular check:
- blade screws on the mowers
- tine screws on the swather and tedder.
Spare part
a. The original components and accessories have
been designed especially for these machines and
appliances.
b. We want to make it quite clear that components and
accesories that have not been supplied by us have
not been tested by us.
c. The installation and/or use of such products can,
therefore, negatively change or influence the
construction characteristics of the appliance. We are
not liable for damages caused by the use of components
and accessories that have not been supplied by us.
d. Alterations and the use of auxiliary parts that are
not permitted by the manufacturer render all liability
invalid.
Cleaning of machine parts
Attention! Do not use high-pressure washers for the
cleaning of bearing- and hydraulic parts.
- Danger of rust!
- After cleaning, grease the machine according to the
lubrication chart and carry out a short test run.
- Cleaning with too high pressure may do damage to
varnish.
Safety point
• Turn engine off when adjustment, service and repair
work is to be done.
Hydraulic unit
Caution! Danger of injury or infection!
Under high pressure, escaping fluids can penetrate
the skin. Therefore seek immediate medical help!
After the first 10 operating hours and then every
consecutive 50 operating hours
- Check the hydraulic unit and lines for tightness and
retighten screw connections if necessary.
Before operation
- Check hydraulic hoses for wear.
Replace worn or damaged hydraulic hoses immediately.
The replacement hoses must meet the manufacturer’s
technical requirements.
Hose lines are subject to natural ageing. The period of
use should not exceed 5 – 6 years.
Winter storage
- Thoroughly clean machine before storage.
- Put up protection against weather.
- Change or replenish gear oil.
- Protect exposed parts from rust.
- Lubricate all greasing points according to lubrication
chart.
Drive shafts
- see notes in the supplement
For maintenance please note!
The instructions in this operating manual are always
valid.
In case there are no special instructions available, then
the notes in the accompanying drive shaft manufacturer´
instructions are valid.
Repair In-
structions
Please refer to
repair instructions
in supplement (if
available)
MAINTENANCE
GB
MAINTENANCE
0700-GB Wartung_353 - 19 -
60 mm
TD 44-97-18
(2x)
119-02-10
After the first hours of operation
- Retighten all screws.
- Above all, check wheel nuts and cutter
screws.
• Always maintain the specified tyre pressure (2 bar).
• Check or adjust V-belt tension.
- After changing V-belts:
- Basic adjustment:
Disc (1) to approx. top control measurement (2).
- Adjust:
- Tension nut:
Tension: turn to the right.
Relieve: turn to the left.
- Secure with lock nut
Roller-type conditioner
Adjustment: 60 mm
Lubrication: 50h
left and right
OIL
Check oil level before starting work.
K1,K2
Check chain tension regularly.
- Do not tension chains too tightly
- Thumb test
K1 = 10 – 12 mm
K2 = 4 – 5 mm
Pos. 13
Adjustment possibility: Both conditioner
rollers should be as parallel to each
other as possible.
GB
MAINTENANCE
0700-GB Wartung_353 - 20 -
4 - 6 mm
66-00-08
5
62
TD45/94/33
Every 50 hours of operation
- Grease all grease nipples according to lubrication chart.
- Grease both drive shafts in machine (see lubrication
chart):
Take sliding sections apart and grease well.
Cutter bar-oil change
After the first 50 hours of operation, then after every
500 hours of operation, or annually.
Note:
• Change oil when at operating temperature.
The oil is too viscid when cold. Too much old oil remains stuck
to the gearwheels and because of this any suspended matter
present cannot be removed from the gearing.
- Drain oil:
- Lift the right side of the mower bar so that the oil gathers in the
drain plug area.
- Remove drain plug (62), drain old oil and dispose of properly.
- Fill with oil:
Full amount: 2,5 - 2,7 litres: SAE 90 EP
Fill check raised 10 cm
1. Lift one side of the mower bar (10 cm) and support.
• The side where the oil refill screw is located remains on
the ground.
• Lift the other side of the mower bar about 10 cm and
support with a suitable prop.
2. Let mower bar stand in this position for some 15 minu-
tes.
• This time is necessary to allow the oil to gather in the
lower area of the mower bar.
3. Remove oil refill screw (5).
The oil level is measured at the oil refill screw hole.
Important!
In doing so the cutter bar must be in horizontal position.
4. Check the "4 - 6 mm" oil level using a wooden stick and
top-up if necessary.
• Too much oil leads to the mower bar overhe-
ating during operation.
• Too little oil does not guarantee the necessary
lubrication.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Pottinger CAT NOVA 260 T CR Operating instructions
- Category
- Lawnmowers
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Pottinger CAT NOVA 310 T CR Operating instructions
-
-
-
-
-
-
-
-
-