Square D Company 9013-FSG2-J21 User manual

Brand: Square D Company

Model: 9013-FSG2-J21

Type: User manual

Data Bulletin

9013DB0701

12/2007

Raleigh, NC USA

Preventive Maintenance and Troubleshooting Guidelines for

Class 9013F and 9013G Pressure Switches

Retain for future use.

Introduction This data bulletin describes how to identify and correct the most common

maintenance issues for the Class 9013F and 9013G Pressure Switches.

Ensure that all maintenance recommended by the original equipment

manufacturer (OEM) is performed. If the equipment fails to operate properly,

refer to the instructions and recommendations provided by the OEM, and

ensure that the instructions were correctly followed. If the operating

problems persist and a pressure switch is the suspected cause, use the

information in this bulletin to assist in troubleshooting the issues.

Inspecting the Pump System

Before the Initial Operation Inspect the following items before operating the pump system:

1. Check the pump’s yield and flow rate.

2. Check the well water level, drawdown, and recovery.

3. Check the line voltage with the pump on and off.

4. Verify that the running current does not exceed the motor nameplate

data.

Before Maintenance Inspect the following items before performing maintenance to the pump

system:

1. Visually inspect the pump system for leakage.

2. Check the pressure switch using a pressure gauge.

3. Record the pressure switch setting if available.

4. Review any system discrepancies or perceived problems in operation.

5. Confirm that electrical power is available and that circuit breakers (or

fuses) are operational.

Providing Routine Maintenance During the normal maintenance period for the pump system, ensure that the

following steps are followed to for all pressure switches.

1. Disconnect the power.

2. Remove the cover.

3. Visually inspect the pressure switch for leakage. Verify that:

— No liquid is leaking from the diaphragm or flange area.

— The flange is not corroded.

— The area is free of standing water and wet spots.

Preventive Maintenance and Troubleshooting Guidelines for Class 9013F and 9013G Pressure Switches 9013DB0701

Providing Routine Maintenance 12/2007

4. Check all plumbing connections. Verify that:

— The flange is not corroded.

— The fittings are secure and without white residue (lime deposits).

5. Check all electrical connections. Verify that:

— The wires are not pinched or frayed, and the insulation is not

cracked.

— There are no insects, contamination, or nests. If found, remove.

NOTE: Contacts may appear pitted. Do not sand or file the contacts. Do

not use chemicals to clean the contacts.

6. Check the system pressure using a pressure gauge.

7. Replace the cover.

8. Restore the power and confirm pump system operation.

9. Open a tap or spigot to confirm water flow.

10. For devices with low pressure cut-out (Form M4), hold the lever to Run

until the pressure is within 10 psi of the cut-in pressure.

Adjusting the Pressure Switch 1. Monitor the pressure gauge during operation to determine the points

where the pressure switch turns on and off.

2. Determine whether to adjust the cut-in, cut-out, or both.

3. If using a tank with an air bladder, determine what air pressure is

required in the bladder.

NOTE: Follow the manufacturer's instructions for setting air pressure to

the required level for the new adjusted pressure switch setting. When

instructions are not available, always set the air pressure in the bladder

to 2 psi below the new desired cut-in pressure. Perform the following

steps to set the air pressure:

a. Turn off the power to the pump.

b. Drain the water from the pressure tank.

c. Using a pressure gauge, take a pressure reading of the tank.

d. Using the air valve, add or remove air from the tank bladder until the

correct pressure is reached.

4. Perform Steps 1–6 of “Providing Routine Maintenance” on page 1.

5. To increase or decrease the cut-in and cut-out settings (while

maintaining the same differential) adjust the pressure switch with a

3/8 inch nut driver or socket as follows:

a. Turn the range nut clockwise for higher cut-in pressure, or counter-

clockwise for lower cut-in pressure. See Figure 1.

NOTE: Adjusting the cut-in setting does not change the differential.

As the cut-in value changes, the cut-out value changes by the same

amount and in the same direction. For example, increasing the cut-in

pressure by 10 psi will also result in an increase in the cut-out

pressure by 10 psi.

When lowering the pressure setting, remember that most bladder

tank water systems are designed for the bladder pressure to be 2 psi

below the cut-in point when there is no water in the tank.

Figure 1: 9013F/9013G Pressure Switches

With Adjustable Differential

Range nut

Types FTG and FHG

Types FSG, FYG, and FRG

Type G

Range nut

Differential

nut

Differential

nut

9013DB0701 Preventive Maintenance and Troubleshooting Guidelines for Class 9013F and 9013G Pressure Switches

12/2007 Providing Routine Maintenance

b. Use the table below as a guideline for setting range nut R.

c. Complete Steps 7 and 8 of “Providing Routine Maintenance” on

page 2.

6. To increase or decrease the cut-out setting (while maintaining the same

cut-in pressure) adjust the pressure switch with a 3/8 inch nut driver or

socket as follows:

a. Complete Steps 1–6 of “Providing Routine Maintenance” on page 1.

b. Turn differential nut D clockwise for higher cut-out pressure, or

counter clockwise for lower cut-out pressure. See Figure 1 on

page 2.

NOTE: Adjusting the differential changes the cut-out setting. The

cut-in does not change.

c. Complete Steps 7–9 of “Providing Routine Maintenance” on page 2.

7. Monitor the system to ensure that the pressure setting is as desired.

a. Open a faucet and drain water from the system until the pump turns

on.

b. Turn off the faucet.

c. Monitor the system pressure to identify the point where the pump

turns off.

d. Repeat Steps 5–7 as required.

Renewal Parts

Original Setting New Setting

Turn Range Nut R

Clockwise

20-40 30-50 3-1/2 Turns

20-40 40-60 8 to 8-1/2 Turns

30-50 40-60 3-1/2 Turns

Table 1: Renewal Parts

Description Part Number

9013F 9013G

Contact kit with contact block, contacts, and

diaphragm

9998PC241 9998PC205

Replacement cover

Include the complete part number of the pressure switch to be used with, including all forms.

65076 605 50 665133 559 50

Preventive Maintenance and Troubleshooting Guidelines for Class 9013F and 9013G Pressure Switches 9013DB0701

Troubleshooting 12/2007

Troubleshooting

Table 2: Troubleshooting Tips

Condition Possible Causes Description/Corrective Action

Corrective Procedure for

Qualified Service Personnel

No water flow

Power is off Confirm that the power is on. —

No water in pressure

system

Confirm the pressure tank pressure reading.

A. If the pressure is below cut-in, and the switch has low pressure cut-

out (Form M4), hold lever in the Run position.

• Marginal or low producing well

• The pump may exceed well

capacity. Restrict pump output or

install smaller pump.

• Check the pumping water level.

1. The pump should turn on and run.

2. When you release the lever, if the M4 feature cuts out the pump

again (within 10 psi of cut-in), the water source is low.

3. Do not actuate the M4 lever again until source has recharged

(the well has water in it).

B. Where Form M4 is not present, check the water source. The well

may be low. Turn off the power to the pump until source has

recharged (the well has water in it).

C. The line to the pressure switch may be plugged, so that the switch

cannot read tank pressure. Check the tank pressure. If it is below

cut-in pressure setting, complete Steps 1–6 of “Providing Routine

Maintenance” on page 1. Look at the contacts to confirm that the

contacts are closed. Complete remaining steps in “Providing

Routine Maintenance” on page 1.

1. Remove the pressure switch from the

pipe and confirm that the entry to the

diaphragm is free of silt and

obstructions.

2. Confirm that any check valves in the

system between the source and the

pressure tank are functioning properly.

3. Confirm that pressure reading at the

pressure switch accurately reflects the

pressure in the pressure tank.

Switch contacts severely

burned

Insects or objects may have entered the space between the contacts.

Remove nests or other havens for insects or vermin near the switch.

Replace the contacts.

The pump is too large. Add a contactor designed for the load.

The application requires a switch with heavy duty contacts.

Replace the switch. Use higher hp

rating.

Rapid cycling

(erratic

operation)

Tank waterlogged

For pre-charged tanks, check the bladder or air valve for leaks and

check tank pressure. If it is below cut-in pressure setting, complete

Steps 1–5 of “Providing Routine Maintenance” on page 1.

Drain some air from the compressed air valve stem. If water comes out,

the bladder is leaking. Completely drain the bladder and recharge with

air as required. Complete the remaining procedures in “Providing

Routine Maintenance” on page 1.

Replace or repair the pressure tank.

Tank not charged

For pre-charged tanks, check the bladder or air valve for leaks and

check the tank pressure. If it is below cut-in pressure setting, complete

Steps 1–5 of “Providing Routine Maintenance” on page 1.

Drain some air from the compressed air valve stem. If water comes out,

the bladder is leaking. Completely drain the bladder and recharge with

air as required. Complete the remaining procedures in “Providing

Routine Maintenance” on page 1.

1. Replace or repair the pressure tank.

2. For conventional tanks, check air

volume control for proper operation.

Drain and recharge tank. Clean or

replace any faulty parts.

Diaphragm damaged

During routine maintenance (see “Providing Routine Maintenance” on

page 1) water is found leaking around diaphragm.

Replace the diaphragm.

Undersized tank

Restrict water usage. Limit the number of devices in operation at any

one time.

Install a larger tank.

Major leak in service lines

Visible water or wet spots may be present. The pump runs, but the tank

is slow to fill.

Check for leaks. Replace damaged

pipes or repair leaks.

Faulty check valve (open) In some systems, water can flow back into the well, emptying the tank.

Check for leaking or open check valve.

Replace if defective.

Foreign material

(calcium deposits)

The line to the pressure switch may be plugged and the switch cannot

read the tank pressure.

Check the tank pressure. If it is below cut-in pressure setting, complete

Steps 1–5 of “Providing Routine Maintenance” on page 1. Look at the

contact plate to confirm that the contacts are closed. Complete the

remaining procedures in “Providing Routine Maintenance” on page 1.

There may be a block in the line

allowing the pressure switch to see high

pressure all the time.

No holding tank — Install a properly sized holding tank.

9013DB0701 Preventive Maintenance and Troubleshooting Guidelines for Class 9013F and 9013G Pressure Switches

12/2007 Troubleshooting

Pump cycles

each time water

is used

Tank waterlogged

For pre-charged tanks, check the bladder or air valve for leaks and

check tank pressure. If it is below cut-in pressure setting, complete

Steps 1–5 of “Providing Routine Maintenance” on page 1.

Drain some air from the compressed air valve stem. If water comes out,

the bladder is leaking. Completely drain the bladder and recharge with

air as required. Complete the remaining steps under “Providing Routine

Maintenance” on page 1.

1. Replace or repair the pressure tank.

2. For conventional tanks, check air

volume control for proper operation.

Drain and recharge tank. Clean or

replace any faulty parts.

Pressure switch

chattering

(contact chatter

or bounce)

Incorrect air pressure in the

bladder

Adjust the air pressure in the bladder to manufacturer's specification.

See the procedures for waterlogged tank.

For conventional tanks, check the air

volume control for proper operation.

Drain and recharge tank. Clean or

replace any faulty parts.

Excessive vibration

The pressure switch may be mounted on rigid pipe and secured by

brackets to the structure. If the pump is also tightly secured, vibration

may be amplified.

Mount the pressure switch to a less rigid

pipe, and shock mount any brackets.

Isolate the switch from other sources of vibration by shock mounting.

Pump shuts off

immediately after

startup

High pressure pump or a

new pump

Add a surge reducer. Order 1530S6G1 for a bag of 50.

Long pump run,

or pump will not

shut off

Too many water outlets

Limit the number of devices running at any one time. —

Increase the size of the pump and/or storage tank Replace the components as desired

Worn pump parts —

Check the pump for worn impellers,

casing, or other close fitting parts.

Water leaks

Check for leaks in service lines. Repair the leaks as required

Plugged discharge pipes

Check for plugged discharge pipes

resulting in reduced flow. Replace the

damaged pipes or repair the leaks.

Switch contacts

burn up

Pump electrical rating is

too high

—

Ensure that the electrical rating of the

switch corresponds to the pump’s

electrical rating.

Add a contactor.

The switch may be replaced by one with

heavy duty contacts.

Switch will not

trip (cut-in/cut-

out) at desired

pressure

Incorrect pressure settings

Adjust to correct pressure settings. See procedures for waterlogged

tank on page 4.

—

Defective pressure gauge Test the pressure gauge. Replace the pressure gauge.

Damaged diaphragm

actuator

— Replace the diaphragm.

Cannot adjust

switch to desired

pressure

Settings outside the

pressure range limits of the

switch

—

Replace the switch with one that has

the correct range and differential

Table 2: Troubleshooting Tips (continued)

Condition Possible Causes Description/Corrective Action

Corrective Procedure for

Qualified Service Personnel

Preventive Maintenance and Troubleshooting Guidelines for Class 9013F and 9013G Pressure Switches 9013DB0701

Troubleshooting 12/2007

Switch operates

mechanically,

but not

electrically

No power to switch

Apply power to the switch.

Check the circuit breaker and/or disconnect switch. If the breaker is

tripped on a new installation, check the switch wiring. Reset the breaker

(disconnect).

Apply power to the switch.

Confirm the wiring of the switch.

Damaged or improperly

installed wiring

Wired to the wrong contact.

Complete Steps 1–5 of “Providing Routine Maintenance” on page 1.

Wire to the correct contacts.

Corroded or loose connections

Make new connections or tighten the

existing connections.

Damaged switch contacts

Replace the switch contacts or entire

switch.

Contacts overloaded (welded)

Complete Steps 6–10 of “Providing Routine Maintenance” on page 1.

• Remove the pressure switch from

the pipe and confirm that the entry

to the diaphragm is free of silt and

obstructions.

• Confirm that any check valves in the

system between the source and the

pressure tank are functioning

properly.

• Confirm that pressure reading at the

pressure switch accurately reflects

the pressure in the pressure tank.

• Low pressure cut-out (M4) has cut-

out.

• Repair or replace the switch if

defective.

• Clean plumbing and pressure port

(replace if defective).

Table 2: Troubleshooting Tips (continued)

Condition Possible Causes Description/Corrective Action

Corrective Procedure for

Qualified Service Personnel

9013DB0701 Preventive Maintenance and Troubleshooting Guidelines for Class 9013F and 9013G Pressure Switches

12/2007 Frequently Asked Questions

Frequently Asked Questions

Table 3: Frequently Asked Questions about Square D Class 9013F and 9013G Pressure Switches

Questions Answers

Can I use a 9013F water pump switch on an air compressor—or a

9013FHG air compressor switch on a water system?

Yes, but not you cannot use a 9013FSG water pump switch on a compressor requiring

Form X.

Is Form M4 (low pressure cut-out) available on the 9013GSG•••

pressure switches?

No, it is not available on the 9013GSG••• pressure switches. It is only available on the

9013FSG••• and the 9013FYG••• pressure switches.

Where can we find information about the 9213 pressure switch?

The information can be found in the 1947 Digest under Pressure Switches. For

information, contact Product Support.

Are 9013FRG pressure switches available in NEMA 3R? No, reverse action 9013F pressure switches are available only in NEMA 1 enclosures.

Are 9013 pressure switches DC voltage rated? Yes, the 9013 pressure switches are rated for DC as noted in Digest 174.

Do the 9013F and 9013G pressure switches accept both solid and

stranded wire?

Yes, the 9013F and 9013G pressure switches accept both solid and stranded wire.

Are the 9013FSG pressure switches CSA approved? Yes, these switches are CSA Approved, File #LR25490.

How can I connect a 9013G pressure switch to control a 3-phase

motor with only a 2-pole set of contacts?

Wire two legs of the 3-phase motor through the two poles of the pressure switch.

Breaking two phases will start and stop the motor. Wire the third leg direct. Install a

disconnect upstream of the pressure switch.

How do I select an appropriate pressure switch?

Refer to the catalog Commercial Pressure Switches Types F and G Class 9013

(9013CT9701) or Industrial Pressure Switches (9012CT9701) located in the Technical

Library at www.us.SquareD.com.

Will a 9013G pressure switch handle 20 A at 230 V, 1-phase and

3 hp?

The 9013G pressure switches are not current rated devices. They are hp rated devices

only. To use on 3-phase circuits, wire 2 phases through the 2 poles of the switch and

direct wire the third phase to one of the motor leads. This makes the lead live when the

pressure switch is off.

Can a 9013FSG2J20 pressure switch be installed horizontally, rather

than the standard vertical mounting?

Yes. The 9013FSG2J20 pressure switch can be mounted horizontally and still work

properly.

Is the catalog number for the 9013 pressure switch valid without the

pressure code?

No. You must have the J code pressure setting to order this product. If a list of pressure

settings is not available, use J99 and include the setpoints desired. The setpoints must

fall within the range of the pressure switch selected.

Is 9013FSG120J20 a valid catalog number?

No. That number indicates that all 9013FSG1 through 9013FSG20 pressure switches

with Form M4 have a different pressure range than the standard pressure switches.

What is the difference between a series B and series C 9013

pressure switch?

Functionally, they are the same device. A series change could have been due to a minor

change in the device. When ordering, customers will receive the latest series available.

What is the temperature range for a 9013F and 9013G pressure

switches?

These temperature ratings apply to all the 9013F and 9013G pressure switches:

Fluid media: -30 to 125 °C (-22 to +257 °F).

Ambient temperature rating: -30 °C to 70 °C (-22 to +158 °F).

What is the maximum allowable pressure for a 9013FRG pressure

switch?

The maximum allowable pressure for a 9013 FRG, GHB, GHG, GSB and GSG pressure

switch is 300 psi.

What is the replacement contact kit for a 9013GHG5 pressure

switch?

The replacement contact kit is 9998 PC205.

Is the 9013GSG2J23R commercial pressure switch available with an

override switch?

No. The closest product with an override switch is the 9012GSG pressure switch with

Form E (On-Auto-Off lever).

Is the low pressure cut-off option on a 9013 pressure switch

adjustable?

The low pressure cutoff remains fixed at 10 psi below the low pressure cut-in for the

pressure switch. Although it is not independently adjustable, it will follow the low pressure

set point. However, the pressure switch will not be effective if the cut-in point is set below

10 psi.

How do I select an appropriate pressure switch?

Refer to the catalog Commercial Pressure Switches Types F and G Class 9013

(9013CT9701), Industrial Pressure Switches (9012CT9701), or Nautilus™ Electronic

Pressure Sensors, XMLE, XMLF, XMLG (9014CT0201).

Is 9998PC52 parts kit still available?

Parts kit 9998PC52 is no longer available.

This parts kit, and all pressure switches using a bellows assembly in their construction

are obsolete. Cross reference the old pressure switch to current products. The available

cross referenced products use diaphragms or pressure transducers.

What is the function of a pulsation plug in a 9013 pressure switch?

The pulsation plug slows the flow of fluid to the diaphragm of the pressure switch to

reduce the surge rate of change. The switch with the plug installed senses change over

longer intervals and does not respond to spikes.

Preventive Maintenance and Troubleshooting Guidelines for Class 9013F and 9013G Pressure Switches 9013DB0701

Data Bulletin 12/2007

Electrical equipment should be installed, operated, serviced, and maintained only by

qualified personnel. No responsibility is assumed by Schneider Electric for any

consequences arising out of the use of this material.

Schneider Electric USA

8001 Knightdale Boulevard

Knightdale, NC 27545 USA

1-888-SquareD (1-888-778-2733)

www.us.SquareD.com

Recommended Protection Install electrical surge protection at the service entrance and in the control

box at the wellhead.

The installer should provide motor circuit overload protection in the pump

motor or control box (if used).

For Additional Information For additional information about common product catalog numbers, visit:

www.us.SquareD.com/pumptrol

Schneider Electric's Pumptrol product manager strives to provide the best

value and service to our Pumptrol customers. For answers to your specific

questions or comments about pumping solutions or products:

e-mail: [email protected]neider-electric.com

Technical Support Technical support is provided Monday through Friday between the hours of

8:00 a.m. and 6:00 p.m. EST. For more information, write or call:

Mailing address:

Schneider Electric Pumptrol Product Line

8001 Knightdale Boulevard

Knightdale, NC 27545-9023

e-mail: [email protected]c.com

Telephone: 1-888-SquareD (1-888-778-2733)

Square D Company 9013-FSG2-J21 User manual

Square D Company 9013-FSG2-J21 User manual

Square D Company 9013-FSG2-J21 User manual

Other documents