Page is loading ...
Networking Motherboard FWB - 225 0
FWB-2250
Networking Motherboard
CompactFlash™ Socket
4 LAN Ports
2 USB 2.0, 1 USB 3.0
1 COM for Console
FWB-2250 Rev. A Manual 1
st
Ed.
July 3, 2015
Networking Motherboard FWB- 2250
Copyright Notice
This document is copyrighted, 2015. All rights are reserved. The
original manufacturer reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, or for any in-
fringements upon the rights of third parties that may result from its
use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have been
made in the preparation of this document to assure its accuracy,
AAEON assumes no liabilities resulting from errors or omissions in
this document, or from the use of the information contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.
i
Networking Motherboard FWB- 2250
Acknowledgments
All other products’ name or trademarks are properties of their
respective owners.
Intel
®
and Atom™ are trademarks of Intel
®
Corporation.
AMI is a trademark of American Megatrends Inc.
CompactFlash™ is a trademark of the Compact Flash
Association.
Microsoft Windows
®
is a registered trademark of Microsoft Corp.
All other product names or trademarks are properties of their
respective owners.
ii
Networking Motherboard FWB- 2250
Caution
There is a danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions and your local government’s recycling or
disposal directives.
Attention:
Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte.
Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le
constructeur. Recycler les batteries usées en accord avec les instructions du
fabricant et les directives gouvernementales de recyclage.
iii
Networking Motherboard FWB- 2250
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
FWB-2250
DVD-ROM for manual (in PDF format)
40W Power Adapter
If any of these items should be missing or damaged, please
contact your distributor or sales representative immediately.
iv
Networking Motherboard FWB- 2250
China RoHS Requirements
产品中有毒有害物质或元素名称及含量
AAEON Main Board/ Daughter Board/ Backplane
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷电路板
及其电子组件
×
○
○
○
○
○
外部信号
连接器及线材
×
○
○
○
○
○
O：表示该有毒有害物质在该部件所有均质材料中的含量均在
SJ/T 11363-2006
标准规定的限量要求以下。
X
：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出
SJ/T 11363-2006
标准规定的限量要求。
备注：此产品所标示之环保使用期限，系指在一般正常使用状况下。
v
Networking Motherboard FWB- 2250
Contents
Chapter 1 General Information
1.1 Introduction .......................................................... 1-2
1.2 Features .............................................................. 1-3
1.3 Specifications ...................................................... 1-4
1.4 General System Information ............................... 1-7
Chapter 2 Quick Installation Guide
2.1 Safety Precautions .............................................. 2-2
2.2 Dimensions .......................................................... 2-3
2.3 Jumpers and Connectors .................................... 2-5
2.4 List of Jumpers .................................................... 2-7
2.5 List of Connectors ............................................... 2-8
2.6 Setting Jumpers .................................................. 2-10
2.7 Auto PWRBTN Selection (JP1) ........................... 2-11
2.8 HDD POWER (CN1, CN4) .................................. 2-11
2.9 CMOS Setting Selection (CN2) ........................... 2-11
2.10 RTCTEST Setting Selection (CN3) ................... 2-11
2.11 CF Power Selection (CN6) ................................ 2-11
2.12 VGA Connector (CN28) .................................... 2-12
2.13 PS2 Header (CN29) .......................................... 2-12
2.14 CPU FAN (CPU FAN) ....................................... 2-12
Chapter 3 AMI BIOS Setup
3.1 System Test and Initialization ............................. 3-2
vi
Networking Motherboard FWB- 2250
3.2 AMI BIOS Setup .................................................. 3-3
Chapter 4 Driver Installation
4.1 Installation ........................................................... 4-3
Appendix A Programming the Watchdog Timer
A.1 Watchdog Timer Initial Program ..................... A-2
Appendix B I/O Information
B.1 I/O Address Map ............................................. B-2
B.2 Memory Address Map ..................................... B-3
B.3 IRQ Mapping Chart ......................................... B-4
Appendix C Standard Firewall Platform Setting
C.1 Standard Firewall Platform Setting ................. C-2
C.2 Status LED Sample Code ............................... C-3
C.3 LAN Bypass Mode Sample Code ................... C-6
C.4 Console Redirection ..................................... C-10
vii
Networking Motherboard FWB- 2250
General
Information
Chapter
1
Chapter 1 General Information 1- 1
Networking Motherboard FWB- 2250
1.1 Introduction
FWB-2250 adopts the Intel
®
Atom™ E3815/E3827/Celeron® J1900
processor SoC. The system memory features two 204-pin single
channel DDR3L 1066/1333 SODIMM up to 8GB. It deploys four
Gigabit Ethernet LAN ports with optional one pair with LAN bypass
function.
In addition, it offers flexible expansion with network products and
features one optional MiniCard socket, two USB 2.0 ports and
one USB 3.0 port, and one RJ-45 console port. The console port
deploys console re-direction that increases the network security
via remote control. All of these designs provide for a more
user-friendly solution.
Chapter 1 General Information 1- 2
Networking Motherboard FWB- 2250
1.2 Features
4-LAN-port Networking Motherboard
Onboard Intel
®
Atom™ E3815/E3827/Celeron® J1900
Processor SoC
204-pin Single Channel DDR3L 1066/1333 SODIMM, up to
8GB
10/100/1000Base-TX Ethernet Port x 4 (up to one pair LAN
bypass)
CompactFlash™ Socket x 1
RJ-45 Console x 1, USB 2.0 x 2, USB 3.0 x 1
DC 12V
MiniCard Socket x 1
Chapter 1 General Information 1- 3
Networking Motherboard FWB- 2250
1.3 Specifications
System
Dimensions
110mm x 145mm (4.33” x 5.71”)
Processor
Intel® Atom™ E3815 1.46 GHz (Single Core)
Intel® Atom™ E3827 1.75 GHz (Dual Core)
Intel® Celeron® J1900 2.0 GHz (Quad Core)
System Memory
204-pin DDR3L 1066/1333 SODIMM x 2,
up
to 8GB
Ethernet Intel
®
Ethernet Controller I211-AT,
Gigabit
Ethernet x 4 (1 pair bypass, optional)
BIOS AMI BIOS
Serial ATA CompactFlash™ x 1
Expansion Interface MiniCard socket x 1
Watchdog Timer 1~255 steps by software programming
MTBF 90,000
OS Support Windows® 7 or above, Linux
Display
Chipset Intel® Atom™ E3815/E3827/Celeron® J1900
Graphic Engine Intel® HD
Resolution 2560x1600
Output Interface Reserved VGA internal box header
I/O
LAN Port RJ-45 Port x 4
Chapter 1 General Information 1- 4
Networking Motherboard FWB- 2250
Serial Port RJ-45 Console x 4
Keyboard & Mouse Reserved pin header
USB USB 2.0 Type A on I/O side x 2
USB 3.0 x 1
LED
Power LED x 1, Status LED x 1, HDD Active x
1, LAN LED x 8, Bypass LED x 1 (Optional)
Others
Power on/off x 1, Software Programmable
Reset x 1
Environment
Operating
Temperature
0°C ~ 60°C (32°F ~ 140°F)
Storage Temperature
-40°C ~ 85°C (-40°F ~ 185°F)
Operating Humidity
0%~90% @RH, non-condensing
Chapter 1 General Information 1- 5
Networking Motherboard
FWB- 2250
Chapter 2 Quick Installation Guide 2-1
Quick
Installation
Guide
Chapter
2
Networking Motherboard
F WB- 2250
Chapter 2 Quick Installation Guide 2-2
2.1 Safety Precautions
The installation is intended for technically qualified personnel who
have experience installing and configuring system boards.
The equipment can be installed in a restricted access location (RAL)
only.
A restricted access location is a site location for equipment where
the following criteria apply:
01. Access can only be gained by service persons or by users who
have been trained on the restrictions and the precautions for this
specific site.
02. Access is by means of at least one of the following, special tool,
lock and key, or other means of security, and is controlled by the
authority responsible for the location.
Safety Precautions:
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis
Networking Motherboard
FWB- 2250
Chapter 2 Quick Installation Guide 2-3
2.2 Dimensions
Networking Motherboard
F WB- 2250
Chapter 2 Quick Installation Guide 2-4
Networking Motherboard
FWB- 2250
Chapter 2 Quick Installation Guide 2-5
2.3 Jumpers and Connectors
Networking Motherboard
F WB- 2250
Chapter 2 Quick Installation Guide 2-6
Networking Motherboard
FWB- 2250
Chapter 2 Quick Installation Guide 2-7
2.4 List of Jumpers
The board has a number of jumpers that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's jumpers:
Label
Function
CN2
Clear CMOS
CN3
RTC TEST
CN6
CF Power Selection
JP1
Auto Power Button
CN30
Power Button
CN31
Software Reset
/
