Adaptec RAID 6405 User guide

Brand: Adaptec

Model: RAID 6405

Type: User guide

User's Guide

Microsemi Adaptec Event Monitor

Released

September 2016

Microsemi makes no warranty, representation, or guarantee regarding the information contained herein

or the suitability of its products and services for any particular purpose, nor does Microsemi assume any

liability whatsoever arising out of the application or use of any product or circuit. The products sold

hereunder and any other products sold by Microsemi have been subject to limited testing and should not

be used in conjunction with mission-critical equipment or applications. Any performance specications

are believed to be reliable but are not veried, and Buyer must conduct and complete all performance

and other testing of the products, alone and together with, or installed in, any end-products. Buyer shall

not rely on any data and performance specications or parameters provided by Microsemi. It is the Buyer's

responsibility to independently determine suitability of any products and to test and verify the same. The

information provided by Microsemi hereunder is provided "as is, where is" and with all faults, and the

entire risk associated with such information is entirely with the Buyer. Microsemi does not grant, explicitly

or implicitly, to any party any patent rights, licenses, or any other IP rights, whether with regard to such

information itself or anything described by such information. Information provided in this document is

proprietary to Microsemi, and Microsemi reserves the right to make any changes to the information in

this document or to any products and services at any time without notice.

Microsemi Corporate Headquarters

One Enterprise, Aliso Viejo,

CA 92656 USA

Within the USA: +1 (800) 713-4113

Outside the USA: +1 (949) 380-6100

Fax: +1 (949) 215-4996

Email: [email protected]om

www.microsemi.com

2016 Microsemi Corporation. All rights

reserved. Microsemi and the Microsemi logo

are trademarks of Microsemi Corporation. All

other trademarks and service marks are the

property of their respective owners.

Microsemi Corporation (Nasdaq: MSCC) offers a comprehensive portfolio of semiconductor

and system solutions for aerospace & defense, communications, data center and industrial

markets. Products include high-performance and radiation-hardened analog mixed-signal

integrated circuits, FPGAs, SoCs and ASICs; power management products; timing and

synchronization devices and precise time solutions, setting the world's standard for time;

voice processing devices; RF solutions; discrete components; enterprise storage and

communication solutions; security technologies and scalable anti-tamper products; Ethernet

solutions; Power-over-Ethernet ICs and midspans; as well as custom design capabilities

and services. Microsemi is headquartered in Aliso Viejo, California, and has approximately

4,800 employees globally. Learn more at www.microsemi.com.

CONFIDENTIAL Document Number: ESC-2160662, Issue 2, September 2016

Revision History

Details of ChangeIssue DateIssue

Update supported OSs; add installing on powerpc instructions; update installing on FreeBSD; update uninstalling on

FreeBSD.

September

2016

Update supported OSs; add downloadable installer instructions; add /etc/init.d start/stop method for linuxApril 20161

3CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Contents

Microsemi Adaptec

Product Support.............................................................................................6

Software License Agreement...........................................................................................................7

1 Overview....................................................................................................................................10

2 Installing and Uninstalling the Event Monitor Utility.................................................................11

2.1 System Requirements.................................................................................................................................11

2.2 Using the Event Monitor Utility with a Firewall..........................................................................................11

2.3 Downloading the Installation Packages......................................................................................................11

2.4 Installing on Windows.................................................................................................................................12

2.5 Performing a Silent Windows Installation...................................................................................................12

2.5.1 Windows Command Line Properties and Examples.....................................................................13

2.6 Installing on Red Hat Linux and Cent OS.....................................................................................................14

2.7 Installing on Debian Linux and Ubuntu Linux..............................................................................................14

2.8 Installing on FreeBSD..................................................................................................................................15

2.9 Installing on PowerPC.................................................................................................................................15

2.10 Uninstalling the Event Monitor Utility......................................................................................................15

3 Stopping and Starting the Event Monitor Service......................................................................17

4 Conguring Event Monitor.........................................................................................................18

5 Email Notications in Linux Event Monitor................................................................................19

6 Event Monitor Log Files..............................................................................................................20

7 Frequently Asked Questions......................................................................................................21

8 More Information......................................................................................................................22

4CONFIDENTIAL Document Number: ESC-2160662, Issue 2

List of Tables

Table 1 • Windows Command Line Exit Codes ........................................................................................................13

Table 2 • Optional Command Line Properties .........................................................................................................13

5CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Microsemi Adaptec

Product Support

If you have questions about installing or using your Microsemi Adaptec

product, check this document

rst—you will nd answers to most of your questions. If you need further assistance, use the support

options listed below. To expedite your service, have your computer in front of you.

Note: Please visit the Support section of www.adaptec.com for the most up to date contact

information.

Self Help and Support in English

• Visit our Web site at www.adaptec.com.

• Search the Adaptec Support Knowledgebase (ASK) at ask.adaptec.com for articles, troubleshooting

tips, and frequently asked questions for your product.

• For support via e-mail, submit your question at ask.adaptec.com.

• To contact Technical Support, visit our product support site at start.adaptec.com and click on

"Contact Support" for options.

Technische Informationen und Support in Deutsch

• Besuchen Sie unsere Webseite www.adaptec.com/de-de

• Suchen Sie in der Adaptec Support Knowledgebase (ASK) unter ask-de.adaptec.com nach Artikeln,

Tipps zur Fehlerbehebung und häug gestellten Fragen zu Ihrem Produkt.

• Support per Email erhalten Sie unter ask-de.adaptec.com.

• Um den Technischen Support zu kontaktieren, besuchen Sie uns bitte unter start.adaptec.com und

klicken Sie auf „Support kontaktieren“, für Auswahlmöglichkeiten.

Техническая поддержка и информация на русском языке

• Посещаете наш сайт www.adaptec.com/ru-ru/.

• База знаний Adaptec (ASK) на сайте ask-ru.adaptec.com ask-ru.adaptec.com – статьи, советы по

устранению неисправностей и часто задаваемые вопросы о Вашем продукте.

• Для поддержки по электронной почте отправьте Ваш запрос на сайте ask-ru.adaptec.com

• Для обращения в службу Технической Поддержки, пожалуйста, посетите наш web сайт

start.adaptec.com и используйте ссылку "Contact Support".

日本語での技術情報とサポート

• 弊社のウェブサイト、www.adaptec.com/ja-jp をご覧ください。

• ask.adaptec.co.jp のAdaptec Support Knowledgebase (ASK)で、お使いの製品の情報トラブルシュー

ティングのヒント、よくある質問を検索してください。

• Eメールでのサポートには ask.adaptec.co.jp から質問を送ってください。

• テクニカルサポートへコンタクトするには、弊社ウェブサイトstart.adaptec.comをご覧になり、"Contact

Support“をクリックして下さい。

6CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Software License Agreement

PLEASE READ CAREFULLY: THE USE OF THIS SOFTWARE IS SUBJECT TO THE SOFTWARE LICENSE TERMS

OF MICROSEMI, INC. AND OTHER LICENSORS WHOSE SOFTWARE MAY BE BUNDLED WITH THIS PRODUCT.

BY YOUR USE OF THE SOFTWARE INCLUDED WITH THIS PRODUCT YOU AGREE TO THE LICENSE TERMS

REQUIRED BY THE LICENSOR OF THAT SOFTWARE, AS SET FORTH DURING THE INSTALLATION PROCESS.

IF YOU DO NOT AGREE TO THE LICENSE TERMS APPLICABLE TO THE SOFTWARE, YOU MAY RETURN THE

ENTIRE UNUSED PRODUCT FOR A FULL REFUND.

In return for acquiring a license to use the Microsemi software, which may include software from third

party licensors and patches made available by Microsemi (“Software”), and the related documentation,

you agree to the following terms and conditions:

1. License. This Agreement grants you, the Licensee, a license to:

a. Use the Software on a single computer system, which is not intended for use by more than ve

(5) users; and:

b. Make one copy of the Software in machine readable form solely for back-up purposes, provided

you reproduce Microsemi's copyright proprietary legends. Notwithstanding the foregoing, the

Software may be used on the home, laptop or other secondary computer of the principal user

of the Software, and an additional copy of the Software may be made to support such use. As

used in this license, the Software is “in use” when it is either loaded into RAM or installed on a

hard disk or other permanent memory device. The Software may be “in use” on only one computer

at any given time. (Different license terms and fees are applicable for networked or multiple user

applications.) As a specic condition of this license, you agree to use the Software in compliance

with all applicable laws, including copyright laws, and that you will not copy, transmit, perform

or distribute any audio or other content using the Software without obtaining all necessary

licenses or permissions from the owner of the content.

2. Restrictions. You may not distribute copies of the Software to others or electronically transfer the

Software from one computer to another over a network. You may not post or otherwise make

available the Software, or any portion thereof, in any form, on the Internet. You may not use the

Software in a computer service business, including in time sharing applications. The Software contains

trade secrets and, in order to protect them, you may not decompile, reverse engineer, disassemble,

or otherwise reduce the Software to a human-perceivable form. YOU MAY NOT MODIFY, ADAPT,

TRANSLATE, RENT, LEASE, LOAN, RESELL FOR PROFIT, DISTRIBUTE, NETWORK OR CREATE DERIVATIVE

WORKS BASED UPON THE SOFTWARE OR ANY PART THEREOF.

3. Ownership of Software. As Licensee, you own the media upon which the software is recorded or

xed, but Microsemi and its licensors retain title and ownership of the Software recorded on the

original media and all subsequent copies of the Software, regardless of the form or media in which

or on which the original and other copies may exist. This license is not a sale of the Software or any

copy.

4. Condentiality. You agree to maintain the Software in condence and that you will not disclose the

Software to any third party without the express written consent of Microsemi. You further agree to

take all reasonable precautions to preclude access of unauthorized persons to the Software.

5. Term. This license is effective until January 1, 2045, unless terminated earlier. You may terminate

the license at any time by destroying the Software (including the related documentation) together

with all copies or modications in any form. Microsemi will have the right to terminate our license

immediately if you fail to comply with any term or condition of this Agreement. Upon any termination,

including termination by you, you must destroy the Software (including the related documentation),

together with all copies or modications in any form.

7CONFIDENTIAL Document Number: ESC-2160662, Issue 2

6. Special Terms Applicable to Databases. Where a database is included with the Software, you

acknowledge that it is licensed only in connection with the use of the Software to perform disc

creation, and that the database and all data derived therefrom must be maintained in condence

in accordance with the provisions of Section 4. This license does not grant you any rights to distribute

or disclose such database or data.

7. Limited Warranty. Microsemi and its Licensor warrant only that the media upon which the Software

is furnished will be free from defects in material or workmanship under normal use and service for

a period of thirty (30) days from the date of delivery to you. MICROSEMI AND ITS LICENSORS DO

NOT AND CANNOT WARRANT THE PERFORMANCE OR RESULTS YOU MAY OBTAIN BY USING THE

SOFTWARE OR DOCUMENTATION. THE FOREGOING STATES THE SOLE AND EXCLUSIVE REMEDIES

MICROSEMI AND ITS LICENSORS WILL PROVIDE FOR BREACH OF WARRANTY. EXCEPT FOR THE

FOREGOING LIMITED WARRANTY, MICROSEMI AND ITS LICENSORS MAKE NO WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED, AS TO NON-INFRINGEMENT OF THIRD PARTY

RIGHTS, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow the

exclusion of implied warranties or limitations on how long an implied warranty may last, so the

above limitations may not apply to you. This warranty gives you specic legal rights and you may

also have other rights which vary from state to state.

8. The entire liability of Microsemi and its licensors, and your exclusive remedy for a breach of this

warranty, shall be:

a. The replacement of any media not meeting the above limited warranty which is returned to

Microsemi; or:

b. if Microsemi or its distributor is unable to deliver replacement media which is free from defects

in materials or workmanship, you may terminate this Agreement by returning the Software and

your money will be refunded.

9. Limitation of Liability. IN NO EVENT WILL MICROSEMI OR ITS LICENSORS BE LIABLE TO YOU FOR ANY

INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES, INCLUDING ANY LOST PROFITS, LOST SAVINGS,

OR LOSS OF DATA, EVEN IF MICROSEMI OR A LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY. Some states do not allow the exclusion

or limitation of special, incidental, or consequential damages, so the above limitation or exclusion

may not apply to you.

10. Export. You acknowledge that the laws and regulations of the United States and other countries

may restrict the export and re-export of the Software. You agree that you will not export or re-export

the Software or documentation in any form in violation of applicable United States and foreign law.

11. Government Restricted Rights. The Software is subject to restricted rights as follows. If the Software

is acquired under the terms of a GSA contract: use, reproduction or disclosure is subject to the

restrictions set forth in the applicable ADP Schedule contract. If the Software is acquired under the

terms of a DoD or civilian agency contract, use, duplication or disclosure by the Government is subject

to the restrictions of this Agreement in accordance with 48 C.F.R. 12.212 of the Federal Acquisition

Regulations and its successors and 49 C.F.R. 227.7202-1 of the DoD FAR Supplement and its successors.

12. General. You acknowledge that you have read this Agreement, understand it, and that by using the

Software you agree to be bound by its terms and conditions. You further agree that it is the complete

and exclusive statement of the agreement between Microsemi and you, and supersedes any proposal

or prior agreement, oral or written, and any other communication between Microsemi and you

relating to the subject matter of this Agreement. No additional or any different terms will be

enforceable against Microsemi unless Microsemi gives its express consent, including an express

waiver of the terms of this Agreement, in writing signed by an ofcer of Microsemi. You assume full

responsibility for the use of the Software and agree to use the Software legally and responsibly. This

Agreement shall be governed by California law, except as to copyright matters, which are covered

by Federal law. This Agreement is deemed entered into at Sunnyvale, California by both parties.

Should any provision of this Agreement be declared unenforceable in any jurisdiction, then such

8CONFIDENTIAL Document Number: ESC-2160662, Issue 2

provision shall be deemed severable from this Agreement and shall not affect the remainder hereof.

All rights in the Software not specically granted in this Agreement are reserved by Microsemi.

Should you have any questions concerning this license, contact:

Microsemi Corporation

Legal Department

One Enterprise

Aliso Viejo, CA 92656

(949) 380-6100

9CONFIDENTIAL Document Number: ESC-2160662, Issue 2

1 Overview

The Microsemi

Adaptec

Event Monitor utility is a software application that monitors and manages

the Microsemi Adaptec storage controllers installed on your system. Its job is to monitor system health,

send notications, and manage task schedules and other on-going processes. It sends notices when

tasks are completed successfully, such as the creation of a logical drive, and sounds an alarm when

errors or failures occur.

The Microsemi Adaptec Event Monitor Utility runs on Windows and Linux systems (see System

Requirements on page 11 for details). Once it is installed, it runs in the background with no user

intervention.

When you install the Event Monitor utility, the Microsemi Adaptec Command Line Interface tool,

ARCCONF, is installed automatically. The CLI tool allows you to build and manage your storage space;

create logical drives; add redundancy to protect your data; check status; recover from a failed physical

device; rebuild logical drives; and more. See Frequently Asked Questions for related documentation.

10CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Overview

2 Installing and Uninstalling the Event Monitor Utility

You can install the Event Monitor utility using an interactive Installation wizard, or you can perform a

“silent” installation from the command line without messages or user interaction. The silent installation

method is suitable for scripted or “batch” installations across multiple machines.

Note: You must install the Event Monitor utility on every system that will be part of your storage

space.

2.1 System Requirements

To install the Microsemi Adaptec Event Monitor Utility, each machine must meet these requirements:

• 20 MB of free disk space

• Microsemi Adaptec storage controller

• One of these operating systems:

Microsoft

Windows

Server 2012 R2 (64-bit), Windows Server 2012 (64-bit), Windows Server

2008 R2, R2 SP1 (64-bit), Windows SBS 2011 Standard and Essential (64-bit), Windows 7,

Windows 8.x, Windows 10, Windows PE 5.x, 8.1 (64-bit)

•

• Red Hat

Enterprise Linux 7.2, 7.1, 6.7,6.6, 5.11, 5.10 (64-bit)

• SuSE Linux Enterprise Server 12, 12 SP1, 11 SP3 and SP4 (64-bit)

• FreeBSD 10.2, 9.3 (64-bit)

• Debian Linux 8.1, 8.3 (64-bit)

• Ubuntu Linux 16.04, 14.04.3, 14.04.2, 12.04.5 (64-bit)

• Fedora Linux 22, 23 (64-bit)

• CentOS 7.3, 7.2, 7.1, 6.7, 6.6, 5.11, 5.10 (64-bit)

2.2 Using the Event Monitor Utility with a Firewall

If your system or network includes a rewall, you must unblock the following ports:

• 8003 (TCP)

• 34580 (TCP)

• 34570 to 34579 (TCP)

• 34570 (UDP)

• 34577 to 34580 (UDP)

For details on unblocking ports, refer to your operating system documentation.

2.3 Downloading the Installation Packages

Complete these steps to download the installation package for your operating system(s):

1. Open a browser window, then type start.adaptec.com in the address bar.

2. Select your RAID controller family (Series 7, Series 8, and so on) and controller model.

3. Select Storage Manager Downloads.

4. Select Adaptec Event Monitor (for Windows and Linux).

5. Click Download Now and accept the license agreement.

6. When the download completes, extract the contents of the installer archive le to a temporary

location. The archive includes installers for multiple operating systems; each installer is stored in a

separate folder.

7. Continue with the installation instructions for your operating system.

11CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Installing and Uninstalling the Event Monitor Utility

2.4 Installing on Windows

Note: You need administrator privileges to install the Microsemi Adaptec Event Monitor Utility.

For details on verifying privileges, refer to your operating system documentation.

To install the Microsemi Adaptec Event Monitor Utility on Windows systems:

1. Open Windows Explorer or My Computer, then change to the directory where the Windows installer

package is located (see Downloading the Installer Package on page 11 for details).

2. Double-click the setup program for your operating system version:

DescriptionOptions

setup_AdaptecEventMonitor_x64_xxxxx.exeWindows 64-bit

The Installation wizard opens.

3. Click Next to begin the installation, click I accept the terms..., and then click Next.

4. Select EventMonitor, accept the default installation directory or click Change... to select a different

installation directory; and then click Next.

Note: To check disk space availability, click Space, review disk space usage, and then click OK.

5. Click Install, and then click Finish.

6. Repeat these steps to install the Microsemi Adaptec Event Monitor Utility on every Windows system

that will be part of your storage space.

2.5 Performing a Silent Windows Installation

To complete a silent Windows installation:

1. Open a command prompt window then change to the directory where the Windows installer package

is located (see Downloading the Installer Package on page 11 for details).

2. Run the silent installation from the command line (where xxxxx is the version number):

• EventMonitorInstaller_x64_xxxxx.exe

For a silent installation, the installer has the following form:

12CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Installing and Uninstalling the Event Monitor Utility

EventMonitorInstaller_x64_xxxxx.exe [ INSTALLDIR=<path> ] [ LOGDIR=<path>

] [ ADDLOCAL=<properties> ]

See Windows Command Line Properties and Examples on page 13 for a description of the command

line options.

After a minute or two, the silent installation should be complete. You may need to reboot the system

if instructed to do so in the install log (see next step).

3. Check the install log, at <LOGDIR>\eventmonitor_install.log, to verify that the installation

completed successfully. The exit codes, shown below, indicate if you need to take further action to

complete the installation.

Table 1 • Windows Command Line Exit Codes

Meaning

ValueCode

The installation was successful. No

reboot is required.

0SUCCESS

The installation was not successful.1FAILURE_GENERAL

The installation was successful, but

a reboot is required.

2SUCCESS_REBOOT

Required hardware is not present,

the software is up to date, or there

is nothing to install.

3SUCCESS_NOT_REQUIRED

Note: For more information about the success or failure of the installation, check the detailed

installation log at <LOGDIR>\adaptec.log. If the installation failed, you will nd detailed

information to help you diagnose the problem.

4. Repeat these steps to install the Microsemi Adaptec Event Monitor Utility on every Windows system

that will be part of your storage space.

2.5.1 Windows Command Line Properties and Examples

A command-line installation (or “silent” installation) uses command-line parameters to complete an

installation without messages or user interaction.

Command Line Properties

Table 2 • Optional Command Line Properties

ValuesProperty

Species the installation path. For example:INSTALLDIR

INSTALLDIR=C:\Program Files\EventMon(Optional)

Note: If you do not set the installation path, the installer uses the following default

path:

C:\Program Files\Adaptec\Adaptec Event Monitor

Species the installation log path. For example:LOGDIR

LOGDIR=C:\Program Files\EventMon\InstallLogs(Optional)

Note: If you do not set the installation log path, the installer uses the following

default path:

C:\PMCS\Logs

ADDLOCAL Note: Use commas to separate multiple values.

(Optional)

13CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Installing and Uninstalling the Event Monitor Utility

ValuesProperty

• ALL—Installs all of the following features. If you specify ALL, do not also specify any

of the following values.

• EventMonitor—Installs the Microsemi Adaptec Event Monitor.

• CLITools—Installs the Command Line Interface tool (ARCCONF).

Example Command Line Installations

Note: In the examples below, xxxxx is the installer version number.

• To install the Microsemi Adaptec Event Monitor, CLI tools (ARCCONF), and installation logs in the

default location:

EventMonitorInstaller_x64_xxxxx.exe

• To install the Microsemi Adaptec Event Monitor, CLI tools, and installation logs to a different

installation path:

EventMonitorInstaller_x64_xxxxx.exe INSTALLDIR=C:\Adaptec\EventMon

LOGDIR=C:\Adaptec\EventMon\InstallLogs

• To install the Microsemi Adaptec Event Monitor and CLI tools to the default location and the

installation logs to a different installation path:

EventMonitorInstaller_x64_xxxxx.exe LOGDIR=”C:\Program Files\Adaptec\Adaptec

Event Monitor\InstallLogs”

Note: Be sure to enclose the installation path in double quotes if the pathname includes

spaces (as in the example above). Do not include a trailing \ on the leaf directory, however,

for example InstallLogs\”; it will be interpreted as an escape sequence for the outside

quote.

• To install just the CLI tools on a 64-bit Windows system:

EventMonitorInstaller_x64_xxxxx.exe ADDLOCAL=CliTools

2.6 Installing on Red Hat Linux and Cent OS

For Red Hat Linux and Cent OS, the Microsemi Adaptec Event Monitor package consists of a RPM le.

You can install the RPM package by double clicking the le in a GUI interface. Alternatively, run the RPM

command from the Linux shell (where xxxxx is the version number):

rpm -ivh EventMonitor-2.02-xxxxx.x86_64.rpm (64-bit)

Where xxxxx is the build version.

Once the RPM is installed, the les are stored under /usr/Adaptec_Event_Monitor. This directory

also includes the Microsemi Adaptec Command Line Utility ARCCONF, which allows you to congure

your RAID storage. The installation creates a user process called ‘EventMonitor’, which runs on the

system that will monitor the Microsemi Adaptec storage controller for events.

2.7 Installing on Debian Linux and Ubuntu Linux

For Debian and Ubuntu Linux, the Microsemi Adaptec Event Monitor is distributed as a .deb package.

You can install the .deb package from the Linux shell with this command (where xxxxx is the version

number):

dpkg –i EventMonitor-2.02-xxxxx_amd64.deb (64-bit)

Where xxxxx is the build version.

Once the DEB package is installed, the les are stored under /usr/Adaptec_Event_Monitor. This

directory also includes the Microsemi Adaptec Command Line Utility ARCCONF, which allows you to

congure your RAID storage. The installation creates a user process called ‘EventMonitor’, which runs

on the system that will monitor the Microsemi Adaptec storage controller for events.

14CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Installing and Uninstalling the Event Monitor Utility

2.8 Installing on FreeBSD

For FreeBSD, use the pkg_add command to install the Microsemi Adaptec Event Monitor (where xxxxx

is the version number):

pkg_add Adaptec_Event_Monitor-2.02-xxxxx-amd64.pkg.tbz (64-bit)

(For FreeBSD 10.x) pkg add Adaptec_Event_Monitor-2.02-xxxxx.txz

Where xxxxx is the build version.

Once the package is installed, the les are stored under /opt/Adaptec_Event_Monitor. This directory

also includes the Microsemi Adaptec Command Line Utility ARCCONF, which allows you to congure

your RAID storage. The installation creates a user process called ‘EventMonitor’, which runs on the

system that will monitor the Microsemi Adaptec storage controller for events.

2.9 Installing on PowerPC

Note: Event Monitor for PowerPC is supported on Microsemi Adaptec Series 8 controllers only

for the following OS versions:

• Ubuntu 16.04

• RHEL 7.2

• Ubuntu 14.04.4

• SUSE Linux 12 SP1

• PowerKVM 3.1.0.1

• Installing Event Monitor:

• Installing on RHEL PowerPC 64-bit

rpm -i EventMonitor-2.02-xxxxx.ppc64le.rpm

• Installing on Ubuntu PowerPC 64-bit

dpkg -i EventMonitor_2.02-xxxxx.ppc64el.deb

• Installing on SLES PowerPC 64-bit

rpm -i EventMonitor-2.02-xxxxx.ppc64le.rpm

Where xxxxx is the build version.

2.10 Uninstalling the Event Monitor Utility

To uninstall Microsemi Adaptec Event Monitor, follow the instructions for your operating system.

Note: If a previous version of Microsemi Adaptec Event Monitor is installed on your system, you

must remove it before beginning a new installation.

Uninstalling on Windows

To uninstall Microsemi Adaptec Event Monitor from a Windows system, use the Add or Remove Programs

tool in the Control Panel. All Microsemi Adaptec Event Monitor components are uninstalled.

When the uninstall process is complete, you receive a conrmation message.

Uninstalling on Linux Red Hat or Cent OS

Type the command: rpm -e EventMonitor

When the uninstall process is complete, you receive a conrmation message.

15CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Installing and Uninstalling the Event Monitor Utility

Uninstalling on Debian Linux or Ubuntu Linux

Type the command: dpkg -r EventMonitor

When the uninstall process is complete, you receive a conrmation message.

Uninstalling on FreeBSD

To uninstall on a FreeBSD system:

1. Change to the /var/db/pkg directory:

cd /var/db/pkg

2. Type the command: pkg_delete Adaptec_Event_Monitor*

3. (For FreeBSD 10.x) Type the command: pkg delete Adaptec_Event_Monitor

16CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Installing and Uninstalling the Event Monitor Utility

3 Stopping and Starting the Event Monitor Service

When you complete a Windows or Linux installation, the Event Monitor service starts automatically.

Stopping and Starting the Service on Windows

To stop the service, restart the service, or disable the service, use the services.msc program

(Administrative Tools) in the Windows Control Panel. The service name, highlighted in the gure below,

is Microsemi Adaptec Event Monitor.

Stopping and Starting the Service on Linux and Unix

To stop and start the ‘EventMonitor’ process on a Linux system, use one of the following commands:

/usr/Adaptec_Event_Monitor/EventMonitorService <start | stop>

/etc/init.d/EventMonitorService <start | stop | restart>

With the /etc/init.d method, a return status of 0 indicates success, which is returned for the

following conditions:

• Running start on a service already running

• Running stop on a service already stopped or not running

• Running restart on a service already stopped or not running

To stop and start the ‘EventMonitor’ process on a FreeBSD system, use the following command:

/opt/Adaptec_Event_Monitor/EventMonitorService <start | stop>

17CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Stopping and Starting the Event Monitor Service

4 Conguring Event Monitor

You can set the following property values in the Event Monitor conguration le, NRMConfig.ini, to

control its behavior:

• nrm.eventQueueSize—the number of events to store before they are posted to the log les. The

default is 200:

nrm.eventQueueSize=200

• nrm.debugMask—the level of debug message output. The following values are supported:

nrm.debugMask=0 ; normal output. Only serious problems are logged (default)

nrm.debugMask=1 ; normal output + events logged to NRMEvents.log

nrm.debugMask=2 ; full debug output

• agent.OSLoggingLevel—the operating system event logging level. The following values are supported:

agent.OSLoggingLevel=0 ; no event logging

agent.OSLoggingLevel=1 ; error events only

agent.OSLoggingLevel=2 ; error and warning events

agent.OSLoggingLevel=3 ; error, warning, and informational events (default)

• agent.alarm—enable or disable the audible alarm. The following values are supported:

agent.alarm=on ; warning and informational events trigger the alarm (default)

agent.alarm=off ; alarm disabled

Note: The property value is not case-sensitive.

See the NRMConfig.ini le, in the installation directory, for a complete list of values for each property.

See Email Notications in Linux Event Monitor for more on event logging.

18CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Conguring Event Monitor

5 Email Notications in Linux Event Monitor

The Email Notication feature in Event Monitor for Linux allows you to send notication emails based

on the events reported by the Event Monitor utility. This feature is disabled by default; it can be

congured after the Event Monitor utility is installed. Once congured, the email notication feature

runs in the background with no user intervention.

Conguring Email Notications

The Event Monitor package includes a script named configureEmailSettings.sh. Use this script

to congure the email notication settings below.

Note: The configureEmailSettings.sh script runs only on the bash shell.

• Enable Email Notication

Enables the Email Notication feature in Event Monitor.

• Disable Email Notication

Disables the Email Notication feature in Event Monitor.

• Get SMTP Server Details

Returns the current SMTP server settings.

• Set SMTP Server Details

Congures the SMTP server settings. The Event Monitor utility can store information about one

SMTP server only. If you already have an existing SMTP server setup, this option will overwrite the

exiting SMTP server settings with new settings. You can congure the following SMTP server details:

• SMTP Server Address—IP address of your SMTP Server.

• SMTP Server Port—port number on which your SMTP server is running.

• From Email Address—from email address.

• Secure SMTP Server—To use a secure SMTP server, choose ‘YES’ for this option. You will need

to provide a username and password for your SMTP server.

• Get Recipient Information

Displays the list of recipients who will receive email notications from Event Monitor.

• Set Recipient Information

Sets the recipient information for users who receive notications from Event Monitor, including:

• Recipient’s Email Address—email address of the recipient.

• Email Notication Type—type of event(s) the recipient is notied of:

I–If this option is selected, the recipient will receive emails for Error, Warning and

Informational events.

•

• W–If this option is selected, the recipient will receive emails for Error and Warning events.

• E–If this option is selected, the recipient will receive emails for Error events only.

• Update Recipient Information

Updates the notication type for a specic recipient.

• Delete Recipient Information

Deletes a specic recipient from the recipient list.

• Send Test Email

Sends a test email based on your SMTP server settings.

Note: After running the conguration script, restart the Event Monitor utility for the

conguration settings to take effect.

19CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Email Notications in Linux Event Monitor

6 Event Monitor Log Files

Windows Log Files

The Event Monitor utility logs events to the Windows Event Viewer (the operating system event logging

utility) and to the Event Monitor log les. The log les are available at the default log path for an

interactive installation (C:\PMCS\Logs), or the <LOGDIR> directory, for a silent installation. Events

are logged to NRMFSAEvents.log for error, warning, and informational events, and NRMFSADebug.log

for debug messages.

Linux and Unix Log Files

The Event Monitor utility logs events to the Syslogs (/var/log/messages) and to the Event Monitor

log les. The Event Monitor log les are located under the /var/log directory. Events are logged to

NRMFSAEvents.log for error, warning, and informational events, and NRMFSADebug.log for debug

messages.

20CONFIDENTIAL Document Number: ESC-2160662, Issue 2

Event Monitor Log Files

Page is loading ...

Adaptec RAID 6405 User guide

Adaptec RAID 6405 User guide

Adaptec RAID 6405 User guide

Related papers

Other documents