Homelite ut46510 Owner's manual

Homelite
Brand
Homelite
Model
ut46510
Type
Owner's manual

Homelite ut46510 is a powerful and versatile cultivator that is perfect for a variety of gardening tasks. With its 4-cycle engine, the ut46510 is easy to start and operate. It also features a 16-inch tilling width, which makes it ideal for small to medium-sized gardens.

Here are some of the features and benefits of the Homelite ut46510:

  • 4-cycle engine for easy starting and operation
  • 16-inch tilling width for small to medium-sized gardens
  • Adjustable tilling depth for customized cultivation
  • Forward and reverse gears for easy maneuverability
  • Foldable handlebars for easy storage
  • Adjustable drag stake for added stability

Homelite ut46510 is a powerful and versatile cultivator that is perfect for a variety of gardening tasks. With its 4-cycle engine, the ut46510 is easy to start and operate. It also features a 16-inch tilling width, which makes it ideal for small to medium-sized gardens.

Here are some of the features and benefits of the Homelite ut46510:

  • 4-cycle engine for easy starting and operation
  • 16-inch tilling width for small to medium-sized gardens
  • Adjustable tilling depth for customized cultivation
  • Forward and reverse gears for easy maneuverability
  • Foldable handlebars for easy storage
  • Adjustable drag stake for added stability
1
HOW TO GET STARTED
HOMELITE ART WORK
Art Part No. : 987000616 Rev. 00
Where Used : 987000616
Refer to Drawings for Dimensions.
987000616
1-20-09 (REV:00)
Make The Most Of Your Purchase!
CALL
1-800-242-4672
www.homelite.com
Material: 60lb. Stock Paper.
Color: Lift-off Bright Pink.
FRONT
For any questions about operating or maintaining your product, call the Homelite Help Line !
Your Product has been fully tested prior to shipment to ensure your complete satisfaction.
Troubleshooting tips are available in your operator's manual.
Go to www.homelite.com and register your new tool on-line.
2
3
4
5
Stand behind the unit with the tines on the ground and the
work area clean and free of obstructions then depress the
switch lock-out.
Carefully remove the product and any accessories from the box. Make sure that all items listed are included.
Loosen the two handlebar knobs. Unfold the handlebar into operating postion. Retighten the handlebar knobs.
To install the tines, lean the unit back on its wheels so that the handlebar rests on the ground.
NOTE: This view of the gearbox for tine installation is from the front of the cultivator.
Place tine C on the tine shaft to the left of the gear box. The stamped side of the tine should face away from the gear box.
Place tine B on the tine shaft to the right of the gear box. The stamped side of the tine should face away from the gear box.
Place a felt washer on each side of the tine shaft, and slide to rest against the inner tines.
Place the outer tine stamped D on the left side of the tine shaft. The stamped side should face in toward tine C.
Place the outer tine stamped A on the right side of the tine shaft. The stamped side should face in toward tine B.
Note: When installed correctly, the angled edge of the tine blades
should face the ground.
To secure the tines to the tine shaft, insert the hitch pin into
the holes located on either side of the tine shaft.
NOTE: The unit will not operate properly if the tines are
installed incorrectly. If you notice a problem with the cultivating
operation of the unit, check for proper tine positioning.
6
7
Route an approved outdoor extension cord through the
upper extension cord retainer ring.
8
9
10
6
Pull the switch trigger toward the handlebar to begin tine rotation.
To stop the cultivator, release the switch trigger.
Position the front handle as shown. Depress the buttons on the handle and insert into the frame.
Press down on the handle until the button on the handle clicks into place.
Locate the axles, hitch pins, washers and wheels. Slide the wheel onto the axle. Place a washer on the outside of the wheel
and slide to rest against the wheel. Push the hitch pin into the hole on the end of the axle to secure the wheel/drag bar assembly.
Repeat with the second wheel.
To install the wheel/drag stake assembly, remove the adjustment knob located at the back of the tine shield. Insert the
wheel/drag stake assembly into the bracket at the back of the tine shield. Insert adjustment knob through holes in bracket,
passing through desired hole in wheel/drag stake assembly, to secure wheel/drag stake assembly at desired height.
Thread the adjustment knob into the nut and tighten, to secure wheel/drag stake assembly.
Tie extension cord to plug connector.
Plug the cultivator into the extension cord.
7
Tine D Tine C
Tine B
Tine A
WARNING: This How To Get Started Procedure is not a substitute for reading the operator’s manual.
To reduce the risk of injury, user must read and understand operator’s manual before using this product.
10
8
9
3
4
2
5
Page is loading ...
  • Page 1 1
  • Page 2 2

Homelite ut46510 Owner's manual

Homelite
Brand
Homelite
Model
ut46510
Type
Owner's manual

Homelite ut46510 is a powerful and versatile cultivator that is perfect for a variety of gardening tasks. With its 4-cycle engine, the ut46510 is easy to start and operate. It also features a 16-inch tilling width, which makes it ideal for small to medium-sized gardens.

Here are some of the features and benefits of the Homelite ut46510:

  • 4-cycle engine for easy starting and operation
  • 16-inch tilling width for small to medium-sized gardens
  • Adjustable tilling depth for customized cultivation
  • Forward and reverse gears for easy maneuverability
  • Foldable handlebars for easy storage
  • Adjustable drag stake for added stability
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents