Woodstock Styling Iron D3119 User manual

Woodstock
Brand
Woodstock
Model
Styling Iron D3119
Type
User manual

This manual is also suitable for

BOARD STRAIGHTENERS ™
INSTRUCTION SHEET
D3119 Board Straighteners
™
How to Use Your Board Straighteners
™
Toholdandcutanirregular-edgedboardwithouttheuse
ofajointer,dothesestepsandsee
Figures 1 and 2.
1. Choose a straight and square
pieceof
1
⁄2"thickwoodforthe
guideboard,whichisthesame
length or longer than the
workpiece you will cut; and
makea
3
⁄16"deepby1
1
⁄2"wide
rabbetcutthecompletelength
ofyourneededguideboard.
2. Positiontheguideboardandworkpiecetoeithersideof
theBoardStraighteners
™
asshowninFigure 1.
3. Tightenthethumbscrewsuntiltheboardsaresecurelyheld.
Forlongboards–useadditionalBoardStraighteners
™
DO
NOTovertightenthethumbscrews.
4. Slide the guideboard against the fence and make your
first cut, remove the workpiece from the Board
Straighteners
™
, and put the freshly-cut side of the
workpieceagainstthefenceandmakeyoursecondcut.
Theworkpieceisnowsquare.
Introduction
Youcannowcutstraightboardsfromirregular-edged
boards without using a jointer! The SHOP FOX
®
ModelD3119BoardStraighteners
™
holdaboardwith
an irregular edge to a guide board with a known
straightedge.Thisstablearrangementcanthenbeslid
alongthetablesawfence,producingastraightcuton
theirregularboard.
• READ and UNDERSTAND this instruction
sheet and your table saw instruction manual
before you use Board Straighteners
™
. Otherwise,
serious personal injury may occur.
• If you are using BOARD BUDDIES
®
or any other
anti-kickback device on your table saw, make sure
that no interference or unsafe condition exists if
used in conjunction with Board Straighteners
™
.
• Always use two or more Board Straighteners
™
to
hold the workpiece to the guide board; otherwise,
the boards can slip apart, causing kickback. It is
often better to use too-many Board Straighteners
™
than too-few.
• ONLY use Board Straighteners
™
for holding an
irregular-edged board to a guide board for cutting
on your table saw. Board Straighteners
™
are not
designed for cutting warped boards, which do not
sit flat on the table. DO NOT modify Board
Straighteners
™
for any other task, but rather, use
“C” clamps, vises, jigs, and bar clamps for
associated clamping and gluing needs.
• Woodstock International Inc.
shall not be
responsible for damage or injuries caused by
improper use of the Board Straighteners
™
. If you
have any questions about the use of this tool,
contact Woodstock International Inc.
ForquestionscontactWoodstockInternationalTechnicalSupportat360-734-3482,orsende-mailto:[email protected].
COPYRIGHT©APRIL2003BYWOODSTOCKINTERNATIONAL,INC.WARNING:NOPORTIONOFTHISDOCUMENTMAYBE
REPRODUCEDINANYSHAPEORFORMWITHOUTTHEWRITTENAPPROVALOFWOODSTOCKINTERNATIONAL,INC.
www.woodstockint.com
Figure 2.
Figure 1.
Guide board
is against
fence
Workpiece
1
1
⁄2"
3
⁄16"
Workpiece
Guide
Board
  • Page 1 1

Woodstock Styling Iron D3119 User manual

Woodstock
Brand
Woodstock
Model
Styling Iron D3119
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents