2. Home
  3. Domestic appliances
  4. Climate control
  5. Fireplaces
  6. FMI
  7. CD32RC-1IS
CD32RC-1IS

FMI CD32RC-1IS Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the FMI CD32RC-1IS Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
DECORATIVE DOOR INSTALLATION FOR MODELS
CD(36,42)RD-1(I,S,W)S AND CD(32,36,42)RC-1(I,S,W)S
Figure 1 - Removing Louvers or smooth Panels (Louvers shown)
(Wood Burning, B-Vent and Vent Free Models)
Figure 3 - Installing Door (Wood Burning, B-Vent and Vent Free
Models
Figure 4 - Attaching Door Frame (All Models) and Installing
Hood (Vent Free Models)
Figure 2 - Installing Mesh Panels (Wood Burning, B-Vent and
Vent Free Models)
Note: Actual replace
may vary from illustration
Note: Actual replace
may vary from illustration
Tabs
Note: Actual replace
may vary from illustration
Control Access
Door Panel
Perforated
Mesh Panel
Note: Actual replace
may vary from illustration
Door Frame
Screws
Hood (Vent Free
Models Only)
Note: If you cannot read or understand these installation in-
structions, do not attempt to install or operate.
WOOD BURNING, B-VENT AND VENT
FREE FIREPLACES
Note: If using a blower, do not attach speed control box to
mounting bracket. Instead, place speed control on replace
oor.
1. For wood burning and vent free replaces, remove top and
bottom (if equipped) louver panels by carefully prying out at
corner and slowly pull away from replace (see Figure 1). For
B-vent replaces refer to step 1 and Figure 5, page 2, to remove
louver panels.
Note: If your replace has 2 louver panels you will use both mesh
panels included with the decorative door kit. If your replace has only
one louver, you will use only one of the mesh panels. If your replace
has control access through the bottom opening, bottom louver will
be replaced with the control access door panel.
2. To install perforated mesh panel, start one end between side
ange and facing. Slide entire panel into place (see Figure 2).
3. To install control access door panel, slide into lower opening
on front of replace (see Figure 2). Magnets located on back
of access door assembly will hold panel in place.
4. Two (2) people may be needed for lifting in this step. To
install decorative door assembly, lift and tilt bottom slightly
outward and insert 3 tabs into rectangular slots located under
top face ange as shown in Figure 3.
5. Open both decorative doors. Secure door frame to replace with
2 screws on each side of lower door frame as shown in Figure 4.
2
120512-01
REV. B
02/11
Figure 6 - Installing Door (Direct Vent Models)
Figure 5 - Removing Louvers (Direct Vent Models)
Figure 7 - Attaching Door Frame and Control Access Door Panel
(Direct Vent Models)
2701 S. Harbor Blvd.
Santa Ana, CA 92704
1-866-328-4537
www.fmiproducts.com
Bottom
Louver
Locating
Holes
Spring
Latch
Tabs
Door Frame
Screws
Magnet
Control Access
Door Panel
6. Depending on your installation, your vent free replace may
require an HD32RC, HD36RC, or HD42RC series hood for
proper clearance to combustibles. Attach hood deector (not
included with decorative door kit) with 4 screws as shown in
Figure 4, page 1.
DIRECT VENT 36'' AND 42'' FIREPLACES
1. Remove existing top and bottom louvers by simultaneously pull-
ing both top end spring latches towards center until disengaged
from locating holes (see Figure 5).
2. Two (2) people may be needed for lifting in this step. To
install decorative door assembly, lift and tilt bottom slightly
outward and insert 3 tabs into rectangular slots located under
face ange as shown in Figure 6.
3. Open both decorative doors. Secure door frame to replace with
2 screws on each side of lower door frame as shown in Figure 7.
4. Install control access door panel by attaching magnets located
on back of access door assembly to lower horizontal glass frame
as shown in Figure 7.
/