Symmons 442SH-1.5 Installation guide

Symmons
Brand
Symmons
Model
442SH-1.5
Type
Installation guide

This manual is also suitable for

Symmons 442SH-1.5 is a showerhead designed for residential and commercial use. It has a flow rate of 1.5 gallons per minute, which meets WaterSense standards for water conservation. The showerhead is made of metal and nonmetallic materials with a polished chrome finish. It comes with a limited lifetime warranty for residential installations and a 5-year warranty for commercial installations. The showerhead is easy to install and maintain, and it can be used with any standard shower arm.

Symmons 442SH-1.5 is a showerhead designed for residential and commercial use. It has a flow rate of 1.5 gallons per minute, which meets WaterSense standards for water conservation. The showerhead is made of metal and nonmetallic materials with a polished chrome finish. It comes with a limited lifetime warranty for residential installations and a 5-year warranty for commercial installations. The showerhead is easy to install and maintain, and it can be used with any standard shower arm.

442HS, 442SH, 442W
Carrington
™
Hand Shower/Showerhead/Hand Shower Wand
Operation & Maintenance Manual
Model Numbers Specifications
442HS Hand Shower Assembly
442SH Showerhead
442W Hand Shower Wand
Hand shower assembly, showerhead and hand shower
wand include standard 2.5 gpm (9.5 L/min) ow restrictor.
Components are made from metal and nonmetallic
materials plated in standard polished chrome nish.
Modifications Compliance
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
-STN Satin nickel finish
-ASME A112.18.1/CSA B125.1
-WaterSense 1.5, 2.0 gpm (442SH only)
Warranty
Limited Lifetime - to the original end purchaser in
consumer installations.
5 Years - for commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Note: Append appropriate -sufx to model number.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667 ■ Fax: (800)961-9621
©2014 Symmons Industries, Inc.
■
www.symmons.com
■
[email protected]
■
ZV-3087 REV 0 09/18/14
Certied by
IAPMO R&T
c
2
Dimensions
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667 ■ Fax: (800)961-9621
©2014 Symmons Industries, Inc.
■
www.symmons.com
■
[email protected]
■
ZV-3087 REV 0 09/18/14
Measurements
A 2 1/8", 54 mm
B
Male 1/2" IPS thread must
be recessed 1/4" from
nished wall
C 1 7/8", 48 mm
D 3 1/4", 83 mm
E 3 1/4", 83 mm
F 4 1/4", 108 mm
G 8 5/8", 219 mm
H 3 1/4", 83 mm
Note: Dimensions are subject to change without notice.
EE
D
D
C
C
B
B
F
F
442SH
442W
442HS
GG
HH
AA
3
Parts Breakdown
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667 ■ Fax: (800)961-9621
©2014 Symmons Industries, Inc.
■
www.symmons.com
■
[email protected]
■
ZV-3087 REV 0 09/18/14
Replacement Parts
Item Description Part Number
B
G
Vacuum Breaker
60" Hose
EF-104
A Wall Elbow EF-105
H Showerhead 442SH
C
D
E
Cradle
Cradle Mounting Screws
Cradle Mounting Plate
EF-106
F Hand Shower 442W
Notes:
1) Append -STN to part number for satin nickel nish.
2) Append -1.5 or -2.0 to showerhead or hand shower
for low ow.
Required for Installation
Adjustable wrench
Phillips head screwdriver
Allen wrench (1/8")
Plumber tape
F
F
B
A
G
E
D
H
442SH 442W
442HS
C
4
Installation
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667 ■ Fax: (800)961-9621
©2014 Symmons Industries, Inc.
■
www.symmons.com
■
[email protected]
■
ZV-3087 REV 0 09/18/14
1) Install wall elbow
(B)
to stub out
pipe. Tighten set screw to secure.
2) Place mounting plate
(F)
in
position, mark and drill 1/8" pilot
holes into stud.
Option:
Place mounting plate
(F)
in
position, mark and drill 3/16" holes
into wall. Install anchors.
3) Remove cover of hand shower
cradle
(D)
. Install cradle and
mounting plate
(F)
. Secure with
three screws
(E)
. Replace cover
on hand shower cradle.
4) Install showerhead
(C)
to shower
arm turning clockwise to tighten.
5)
Attach large end of hand shower
hose (H) to hand shower head (G).
Attach small end of hand shower
hose (H) and gasket to in-line
vacuum breaker (A). Connect
in-line vacuum breaker to wall
elbow (B). Turn clockwise to
tighten.
1
2
B
1
3
2
F
1
2
F
4
3
F
E
D
2
1
3
1
4
2
H
G
A
H
B
1
2
C
5
Care and Cleaning
1) Clean nished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse
with water.
Troubleshooting Chart
Problem Cause Solution
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then
quickly rinse with water.
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ (800)796-6667 ■ Fax: (800)961-9621
©2014 Symmons Industries, Inc.
■
www.symmons.com
■
[email protected]
■
ZV-3087 REV 0 09/18/14
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Symmons 442SH-1.5 Installation guide

Symmons
Brand
Symmons
Model
442SH-1.5
Type
Installation guide
This manual is also suitable for

Symmons 442SH-1.5 is a showerhead designed for residential and commercial use. It has a flow rate of 1.5 gallons per minute, which meets WaterSense standards for water conservation. The showerhead is made of metal and nonmetallic materials with a polished chrome finish. It comes with a limited lifetime warranty for residential installations and a 5-year warranty for commercial installations. The showerhead is easy to install and maintain, and it can be used with any standard shower arm.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents