BEGLEC ENH2.3 Owner's manual

Brand: BEGLEC

Model: ENH2.3

Category: Subwoofers

Type: Owner's manual

Version: 1.0

WWW.BEGLEC.COM

Operation Manual

Mode d'emploi

Gebruiksaanwijzing

Bedienungsanleitung

Manual de instrucciones

Manual do utilizador

The Power Source for DJ’s

‘t Hofveld 2C ~ B1702 Groot-Bijgaarden ~ Belgium

Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.

MULTIBAND SOUND PROCESSOR

EN - DISPOSAL OF THE DEVICE

Dispose of the unit and used batteries in an environment friendly manner

according to your country regulations.

FR - DÉCLASSER L’APPAREIL

Débarrassez-vous de l’appareil et des piles usagées de manière écologique

Conformément aux dispositions légales de votre pays.

NL - VERWIJDEREN VAN HET APPARAAT

Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke

manier conform de in uw land geldende voorschriften.

DU - ENTSORGUNG DES GERÄTS

Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und

Weise gemäß den Vorschriften Ihres Landes.

ES - DESHACERSE DEL APARATO

Reciclar el aparato y pilas usadas de forma ecologica conforme a las

disposiciones legales de su pais.

PT - COMO DESFAZER-SE DA UNIDADE

Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em

conformidade com as normas vigentes no seu país.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 1/30 ENH2.3 / SE-100

OPERATION MANUAL

FEATURES

 Professional multi-band sound enhancer: adds harmonics to the sound which

increases definition, presence and transparency.

 Improves bass punch considerably

 Separate variable subwoofer output with adjustable cutoff frequency

 Subwoofer inverter switch

 50Hz/100Hz low cut filter

 Variable sound processing for perfect sound balance

 Enhancer multi-band tuning from 1kHz to 8kHz.

 Balanced XLR inputs/outputs

BEFORE USE

Check the contents:

Check that the carton contains the following items:

 ENH2.3 / SE-100 Enhancer unit

 Operating instructions

 Power cord with IEC-plug

SAFETY INSTRUCTIONS:

CAUTION: To reduce the risk of electric shock, do not

remove the top cover. No user-serviceable parts inside.

Refer servicing to qualified service personnel only.

The lightning flash with arrowhead symbol within the

equilateral triangle is intended to alert the use or the

presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the

presence of important operation and maintenance (servicing) instructions in the literature

accompanying this appliance.

This symbol means: indoor use only.

This symbol means: Read instructions.

 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures

when bringing it into a warm room after transport. Condense sometimes prevents the unit from

working at full performance or may even cause damages.

 This unit is for indoor use only.

 Don’t place metal objects or spill liquid inside the unit. No objects filled with liquids, such as vases,

shall be placed on this appliance. Electric shock or malfunction may result. If a foreign object enters

the unit, immediately disconnect the mains power.

 No naked flame sources, such as lighted candles, should be placed on the appliance.

 Don’t cover any ventilation openings as this may result in overheating.

 Prevent use in dusty environments and clean the unit regularly.

 Keep the unit away from children.

 Inexperienced persons should not operate this device.

CAUTION

ENGLISH OPERATION MANUAL

JB SYSTEMS® 2/30 ENH2.3 / SE-100

 Maximum save ambient temperature is 45°C. Don’t use this unit at higher ambient temperatures.

 Always unplug the unit when it is not used for a longer time or before you start servicing.

 The electrical installation should be carried out by qualified personal only, according to the

regulations for electrical and mechanical safety in your country.

 Check that the available voltage is not higher than the one stated on the rear panel of the unit.

 The socket inlet shall remain operable for disconnection from the mains.

 The power cord should always be in perfect condition. Switch the unit immediately off when the

power cord is squashed or damaged. It must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a hazard.

 Never let the power-cord come into contact with other cables!

 When the power switch is in OFF position, this unit is not completely disconnected from the mains!

 This appliance must be earthed to in order comply with safety regulations.

 In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no

user serviceable parts inside.

 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the

same type and electrical specifications!

 In the event of serious operating problems, stop using the appliance and contact your dealer

immediately.

 Please use the original packing when the device is to be transported.

 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

INSTALLATION GUIDELINES:

 Install the unit in a well-ventilated location where it will not be exposed to high

temperatures or humidity.

 Placing and using the unit for long periods near heat-generating sources such as

amplifiers, spotlights, etc. will affect its performance and may even damage the

unit.

 The unit can be mounted in 19-inch racks. Attach the unit using the 4 screw holes

on the front panel. Be sure to use screws of the appropriate size. (screws not

provided)

Take care to minimize shocks and vibrations during transport.

 When installed in a booth or flight case, please make sure to have good ventilation

to improve heat evacuation of the unit.

 To avoid condensation to be formed inside, allow the unit to adapt to the

surrounding temperatures when bringing it into a warm room after transport.

Condense sometimes prevents the unit from working at full performance.

CONNECTIONS

This sound enhancer can be used in different ways. Basically the unit is connected

between the music source (any line output is possible) and the unit that will be used

to record or amplify the music:

 In most cases SE100 will be used to enhance the sound quality and bass punch in

PA systems and discotheque sound systems. The SE100 will be connected behind

the master output of the audio mixer. You can also use the subwoofer output to

drive an extra subwoofer amplifier which results in an additional power punch!

 SE100 can be inserted in the monitor send of a PA mixer to enhance the sound

quality of monitor speakers.

 SE100 can also be used between a tape deck and mixing console to enhance the

sound of the tape deck.

 SE100 can be connected between the record output of a mixing console and a tape

deck to enhance the sound that will be recorded.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 3/30 ENH2.3 / SE-100

 SE100 can be used to correct the loss of sound quality, caused by all kinds of effect

equipment. In this case put the SE100 as last unit in the chain of effect equipment.

 SE100 can be used to compensate the loss of sound definition during tape

duplication: the copy can be even better than the original! Put the SE100 between

the output of the playback deck and the input of the recording deck.

For additional information on connections please refer to the next paragraph.

REAR PANEL: CONNECTIONS

1. INPUT connector: this female XLR-connector accepts both unbalanced and

balanced line signals from the unit that needs audio enhancement.

 For balanced use, please follow these conventions:

Pin1 = Ground ~ Pin2 = Hot (+) ~ Pin3 = Cold (-)

Readymade cables are available from JB Systems (ex. 7-0063 ~ 5m XLR m/f)

 For unbalanced use, connect Pin3 (-) to Pin1 (ground/shield)

Readymade cables are available from JB Systems (2-0445 ~ cinch/XLR m)

2. OUTPUT connector: this male XLR-connector can be connected to both

unbalanced and balanced line inputs.

 For balanced use, please follow these conventions:

Pin1 = Ground ~ Pin2 = Hot (+) ~ Pin3 = Cold (-)

Readymade cables are available from JB Systems (ex. 7-0063 ~ 5m XLR m/f)

 For unbalanced use, connect Pin3 (-) to Pin1 (ground/shield)

Readymade cables are available from JB Systems (2-0440 ~ cinch/XLR f)

3. SUBWOOFER OUTPUT connector: this male XLR-connector can be connected

to both unbalanced and balanced inputs of subwoofer amplifiers. The cutoff

frequency and level of this output are adjustable.

 For balanced use, please follow these conventions:

Pin1 = Ground ~ Pin2 = Hot (+) ~ Pin3 = Cold (-)

Readymade cables are available from JB Systems (ex. 7-0063 ~ 5m XLR m/f)

 For unbalanced use, connect Pin3 (-) to Pin1 (ground/shield)

Readymade cables are available from JB Systems (2-0440 ~ cinch/XLR f)

4. Mains input: connect the sound enhancer to the 220V AC mains, using the

supplied power-cord.

ENGLISH OPERATION MANUAL

JB SYSTEMS® 4/30 ENH2.3 / SE-100

FRONT PANEL: CONTROLS AND USE

5. ACTIV switch: This button switches the processor over between operation and

bypass. When the button is pressed the blue led turns on to indicate that the

processor works. You can use this switch to compare the sound with and without

processing. This makes it easier to tune the sound using trial and error.

6. SHIFT switch: Sets the cutoff lower frequency of the bass processor. Depending

on the situation you can select 50Hz or 100Hz cutoff frequency for the bass

processor. This function also helps reducing system load.

7. LOW MIX control: Controls the amount of low band signal, produced by the bass

processor, used for sound enhancement (from zero to maximum). The setting

depends on the application and can be adapted to your own taste. When

adjusting, use the ACTIV switch to compare between original and processed

sound.

Important: Note that the bass processor should be used with care to avoid

possible speaker damage. Most smaller and economical speakers are not

capable of handling the low frequencies produced by this unit.

8. TUNE control: Sets the cutoff frequency of the high-pass filter. In a range from

1kHz to 8kHz you can select the frequencies that are routed to the high band

processor.

9. PROCESSOR control: controls the efficiency of the high band processor. The

signals’ transparency and sharpness increases while turning the control knob in

clockwise direction. When adjusting, use the ACTIV switch to compare between

original and processed sound.

10. HIGH MIX control: Controls the amount of signal, produced by the high band

processor, used for sound enhancement (from zero to maximum). The setting

depends on the application. It can be used to give a high-quality system the little

“finishing touch” it needs or you can add some extra clarity to a relatively poor

sound system. In any case it is up to you to adapt the sound to your own taste.

Always start adjusting with the HIGH MIX control turned in counterclockwise

position and use the ACTIV switch often to compare between original and

processed sound.

Important: Note that the high band processor should be used with care to avoid

possible tweeter damage. Improper and excessive use of high band processor

can cause overload to the tweeters of your speakers. Always start tuning the high

band processor with the HIGH MIX control completely turned to the left.

11. PHASE INVERT switch: To add more bass punch, a subwoofer can be

connected to the subwoofer output. Sometimes the conductors of the subwoofer

are inversed which results in poor sound quality with a lack of low frequencies:

the opposite of what you expected! This can be corrected by inversing the (+) and

(-) poles of the cabling to your subwoofer or … by pushing the PHASE INVERT

ENGLISH OPERATION MANUAL

JB SYSTEMS® 5/30 ENH2.3 / SE-100

switch! Press the phase invert switch and compare the results of both positions.

The position with the most bass production is the right one!

12. X-OVER FREQ. control: (crossover frequency control) adjusts the cutoff

frequency of the subwoofer low pass filter. This crossover frequency can be set in

a range of 100 to 250Hz. Once again it is up to you to adapt its position to your

own taste. For most subwoofers 100Hz to 150Hz seems to be the best choice.

13. OUTPUT control: Controls the level of the subwoofer output from zero to +12dB.

Start from zero and slowly turn in clockwise direction until the amount of low

frequencies seems to be OK for you.

14. CLIP LED: When the subwoofer output level is too big, clipping may occur. In this

case the clip led turns on. No problem if the led blinks from time to time. However

when this happens too often, it’s time to lower the subwoofer output signal.

Note: Clipping means deformation and deformation means possible damage to

your subwoofer…

15. LED BAR: Small led bar indicates the output level of both enhancer outputs.

SPECIFICATIONS

Max. input level / impedance: +20dBu unbalanced / 40kΩ

Max. output level / impedance: +20dBu unbalanced / 40Ω

Common mode rejection (CMRR): >40dB

Frequency response: 10-30.000Hz (+/-0.5dB)

THD(A) + noise: 0.005% +4dB

IMD Intermodulation distortion: 0.01% +10dB

S/N Ratio (IHF-A): >94dB (20-20.000Hz)

Crosstalk @20kHz: > -83dBu

Power Supply: AC 230 V, 50Hz

Power Consumption: 10W

Fuse: 0.5A slow blow

Dimensions: 482(W) x 44(H) x 154(D) mm

Weight: 1Kgs

Every information is subject to change without prior notice

You can download the latest version of this user manual on our website: www.beglec.com

FRANCAIS MODE D’EMPLOI

JB SYSTEMS® 6/30 ENH2.3 / SE-100

CAUTION

MODE D’EMPLOI

CARACTERISTIQUES

 Sound enhancer multi-bandes professionnel: ajoute des harmoniques au son, ce

qui augmente la définition, la présence et la transparence.

 Accentue considérablement les basses (plus de punch)

 Sortie séparée pour le sub-woofer avec réglage du niveau de sortie et de la

fréquence de coupure.

 Inverseur de polarité du sub-woofer

 Filtre « low cut » 50Hz/100Hz

 Traitement variable du son pour une balance sonore parfaite

 Enhancer multi-bandes : tuning de 1kHz à 8kHz.

 Entrées / sorties XLR balancées

AVANT L’UTILISATION

Vérifiez le contenu:

Vérifiez si la boite contient les articles suivants :

 Le ENH2.3 / SE-100

 Le mode d’emploi

 Câble d’alimentation au connecteur IEC

INSTRUCTIONS DE SECURITE:

ATTENTION: afin de réduire le risque d’électrocution,

n’enlevez jamais le couvercle de l’appareil. Il n’y a

aucune pièce à l’intérieur de l’appareil que vous pouvez

remplacer vous-même. Confiez l’entretien uniquement à

des techniciens qualifiés.

La flèche dans un triangle met l'utilisateur en garde contre la présence de haute tension

sans isolation dans l'appareil qui peut causer un risque d'électrocution.

Un point d'exclamation dans un triangle prévient de la présence d'instructions de

fonctionnement et de maintenance se trouvant dans le manuel, fourni avec l'appareil.

Ce symbole signifie : uniquement pour usage à l'intérieur

Ce symbole signifie : Lire le mode d’emploi.

 Afin d’éviter tout risque d’incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou

l’humidité.

 Pour éviter la formation de condensation à l’intérieur de l’appareil, patientez quelques minutes pour

laisser l’appareil s’adapter à la température ambiante lorsqu’il arrive dans une pièce chauffée après

le transport. La condensation empêche l’unité de fonctionner en performance optimale et peut

même causer des dommages.

 Cette unité est destinée à une utilisation à l’intérieur uniquement.

 Ne pas insérer d’objet métallique ou verser un liquide dans l’appareil. Aucun objet rempli de

liquides, tels que des vases, ne peut être placé sur cet appareil. Risque de choc électrique ou de

dysfonctionnement. Si un corps étranger est introduit dans l’unité, déconnectez immédiatement de

la source d’alimentation.

Page is loading ...

BEGLEC ENH2.3 Owner's manual

Brand: BEGLEC

Model: ENH2.3

Category: Subwoofers

Type: Owner's manual

Download PDF

report

in other languages

français: BEGLEC ENH2.3 Le manuel du propriétaire
español: BEGLEC ENH2.3 El manual del propietario
Deutsch: BEGLEC ENH2.3 Bedienungsanleitung
Nederlands: BEGLEC ENH2.3 de handleiding
português: BEGLEC ENH2.3 Manual do proprietário

BEGLEC ENH2.3 Owner's manual

BEGLEC ENH2.3 Owner's manual

in other languages

Related papers

Other documents