KONICA Dimage E203 User manual

Brand: KONICA

Model: Dimage E203

Type: User manual

This manual is also suitable for

DIMAGE E203 - SOFTWARE

INSTRUCTION MANUAL

9224-2774-11 H-A107

Thank you for purchasing this Minolta digital camera. Please take the time to read through this

instruction manual so you can enjoy all the features of your new camera.

Check the packing list before using this product. If any items are missing, immediately contact your

camera dealer.

BEFORE YOU BEGIN

Minolta DiMAGE E203 digital camera

CR-V3 lithium battery

Hand strap for DiMAGE E203

HS-DG203

USB cable for DiMAGE E203

USB-400

DiMAGE E203 software CD-ROM

ArcSoft PhotoImpression CD-ROM

(packaged in one case)

Camera manual

Warranty card

8MB SD Memory Card

MINOLTA

Warranty

Read and understand all warnings and cautions before using this product.

Using batteries improperly can cause them to leak harmful solutions, overheat, or explode which may

damage property or cause personal injury. Do not ignore the following warnings.

• Only use the batteries specified in this instruction manual.

• Do not install the batteries with the polarity (+/–) reversed.

• Do not use batteries which show wear or damage.

• Do not expose batteries to fire, high temperatures, water, or moisture.

• Do not attempt to short or disassemble batteries.

• Do not store batteries near or in metallic products.

• Do not mix batteries of different types, brands, ages, or charge levels.

• Do not charge alkaline or lithium batteries.

• When recharging rechargeable batteries, only use the recommended charger.

• Do not use leaking batteries. If fluid from the batteries enters your eye, immediately rinse the eye

with plenty of fresh water and contact a doctor. If fluid from the batteries makes contact with your

skin or clothing, wash the area thoroughly with water.

WARNING

• Use only the specified AC adapter within the voltage range indicated on the adapter unit. An

inappropriate adapter or current may cause damage or injury through fire or electric shock.

• Do not disassemble this product. Electric shock may cause injury if a high voltage circuit inside the

product is touched.

• Immediately remove the batteries or unplug the AC adapter and discontinue use if the camera is

dropped or subjected to an impact in which the interior, especially the flash unit, is exposed. The

flash has a high voltage circuit which may cause an electric shock resulting in injury. The continued

use of a damaged product or part may cause injuries or fire.

• Keep batteries or small parts that could be swallowed away from infants. Contact a doctor

immediately if an object is swallowed.

• Store this product out of reach of children. Be careful when around children, not to harm them with

the product or parts.

• Do not fire the flash directly into the eyes. It may damage eyesight.

• Do not fire the flash at vehicle operators. It may cause a distraction or temporary blindness which

may lead to an accident.

• Do not use the monitor while operating a vehicle or walking. It may result in injury or an accident.

• Do not use this product in a humid environment, or operate this product with wet hands. If liquid

enters the product, immediately remove the batteries or unplug the AC adapter and discontinue

use. The continued use of a product exposed to liquids may cause damage or injury through fire or

electric shock.

• Do not use the product near inflammable gases or liquids such as gasoline, benzine, or paint

thinner. Do not use inflammable products such as alcohol, benzine, or paint thinner to clean the

product. The use of inflammable cleaners and solvents may cause an explosion or fire.

• When unplugging the AC adapter, do not pull on the power cord. Hold the plug when removing it

from an outlet.

• Do not damage, twist, modify, heat, or place heavy objects on the AC adapter cord. A damaged

cord may cause damage or injury through fire or electric shock.

• If the product emits a strange odor, heat, or smoke, discontinue use. Immediately remove the

batteries taking care not to burn yourself as the batteries become hot with use. The continued use

of a damaged product or part may cause injuries or fire.

• Take the product to a Minolta Service Facility when repairs are required

FOR PROPER AND SAFE USE

CAUTION

• Do not use or store the product in a hot or humid environment such as the glove compartment or

trunk of a car. It may damage the product and batteries which may result in burns or injuries

caused by heat, fire, explosion, or leaking battery fluid.

• If batteries are leaking, discontinue use of the product.

• The camera temperature rises with extended periods of use. Care should be taken to avoid burns.

• Burns may result if the memory card or batteries are removed immediately after extended periods

of use. Turn the camera off and wait for it to cool.

• Do not fire the flash while it is in contact with people or objects. The flash unit discharges a large

amount of energy which may cause burns.

• Do not apply pressure to the LCD monitor. A damaged monitor may cause injury, and the liquid

from the monitor may cause inflammation. If liquid from the monitor makes contact with skin wash

the area with fresh water. If liquid from the monitor comes in contact with the eyes, immediately

rinse the eyes with plenty of water and contact a doctor.

• When using the AC adapter, insert the plug securely into the electrical outlet.

• Do not use if the AC adapter cord is damaged.

• Do not cover the AC adapter. A fire may result.

• Do not obstruct access to the AC adapter; this can hinder the unplugging of the unit in

emergencies.

• Unplug the AC adapter when cleaning or when the product is not in use.

TABLE OF CONTENTS

About SD Memory Cards and MultiMediaCards ...................................................7

Names of parts ......................................................................................................8

Camera body ...............................................................................................8

Data panel ...................................................................................................9

Viewfinder ....................................................................................................9

Mode dial .....................................................................................................9

Getting up and running ........................................................................................10

Installing a CR-V3 lithium battery..............................................................10

Installing AA batteries................................................................................10

Battery-condition indicator .........................................................................11

Auto power off............................................................................................11

AC adapter (sold separately).....................................................................11

Installing and removing a memory card ....................................................12

Attaching the hand strap............................................................................12

Setting up the camera ...............................................................................13

Basic recording operation..........................................................................14

Using the zoom lens ..................................................................................14

Focus lock..................................................................................................15

Special focusing situations ........................................................................15

Handling the camera..................................................................................15

Viewing pictures.........................................................................................16

Enlarged playback .................................................................................16

Camera controls – auto-recording and multi-function recording modes..............17

Tur ning on the LCD monitor – the display button ......................................17

Mode button...............................................................................................18

Flash modes ..............................................................................................19

Flash range................................................................................................19

Flash signals..............................................................................................19

Subject-programs.......................................................................................20

Camera-shake warning..............................................................................20

Self-timer ...................................................................................................21

Image-size button ......................................................................................22

About the frame counter ............................................................................22

Auto-recording menu............................................................................................23

Setting the LCD monitor brightness ..........................................................23

Multi-function recording menu..............................................................................24

Navigating the multi-function recording menu ...........................................24

Reset menu ...........................................................................................26

Movie recording .....................................................................................26

Digital zoom...........................................................................................27

Exposure compensation ........................................................................27

White balance........................................................................................28

Automatic white balance ..................................................................28

Preset white balance........................................................................28

Spot metering ........................................................................................29

Slow shutter...........................................................................................29

LCD monitor brightness.........................................................................29

Colour mode ..........................................................................................29

TABLE OF CONTENTS

Playback mode – viewing and editing images.....................................................30

Viewing pictures.........................................................................................30

Enlarged playback .....................................................................................31

Viewing movies ..........................................................................................31

Navigating the playback menu...................................................................32

Deleting images.....................................................................................34

Index playback .......................................................................................34

Slide show .............................................................................................35

Locking and unlocking images ..............................................................35

Displaying the file number .....................................................................36

LCD monitor brightness.........................................................................36

About DPOF ..........................................................................................36

Creating a DPOF print order .................................................................36

Setup mode – adjusting camera operation..........................................................38

Navigating the setup menu ........................................................................38

Formatting memory cards......................................................................40

Self-timer period ....................................................................................40

Auto-power-off period ............................................................................40

File number memory..............................................................................40

Beep ......................................................................................................41

Instant playback.....................................................................................41

Setting the date and time ......................................................................41

Setting the language..............................................................................41

PC mode – connecting to a computer .................................................................42

Arcsoft PhotoImpression 3.0 system requirements...................................42

QuickTime 5.0 system requirements .........................................................42

Connecting the camera to a computer ......................................................43

Connecting to Windows 98 and 98SE .......................................................44

Memory card folder organization ...............................................................45

Auto power off (PC mode) .........................................................................46

Disconnecting the camera from the computer...........................................46

Macintosh ..............................................................................................46

Windows 98 and 98SE ..........................................................................46

Windows Me and Windows 2000 Professional......................................47

Changing the memory card (PC mode) ....................................................48

Appendix ...........................................................................................................49

Troubleshooting..........................................................................................50

Care and storage.......................................................................................52

Technical specifications .............................................................................54

• The following may cause data loss or damage.

1. Improper use of the card.

2. Static electrical discharge or electromagnetic fields near the card.

3. Removing the card or interrupting the power supply while the camera or a computer is

accessing the card (reading, writing, formatting, etc.).

4. The disuse of a card for an extended period.

5. Using the card beyond its life.

Minolta has no responsibility for any loss or damage to data.

It is recommended that a copy of the card data be made in another media such as a ZIP disc, hard

disk, CD-ROM, etc.

• When the card is formatted, all recorded data will be deleted. Be sure to make a backup of any

important data.

• The storage capability of the memory card will diminish with extended use. It may be necessary to

purchase a new card periodically.

• Keep away from static electricity and electromagnetic fields.

• Do not bend, drop, or subject the card to impact.

• Static electrical discharges or physical shock may prevent the card from being able to transfer data.

• Do not touch the electrical contacts of the card with your fingers or metal objects.

• Keep away from heat, moisture, and direct sunlight.

• Keep away from small children.

ABOUT SD MEMORY CARDS AND MULTI MEDIA CARDS

SD Memory Cards and MultiMediaCards are manufactured

with precision electronic components. Please read the fol-

lowing cautions:

The SD Memory Card has a write-protect switch to prevent

image data from being deleted. By sliding the switch to the

bottom of the card, the data will be protected. However,

when the card is protected, images can not be recorded. If

an attempt is made to record or delete an image with the

camera, the LED lamps near the viewfinder and the frame

counter on the data panel will blink and will be accompa-

nied by an audio signal.

Write-protect

switch

Lock

position

The response time during recording and playback is longer with MultiMediaCards compared with SD

Memory Cards. This is not a defect, but rather due to the specifications of the cards. When using

large capacity cards, some operations like deletion may take longer.

NAMES OF PARTS

* This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces

clean. Please read the care and storage instructions in the back of this manual (p. 52).

CAMERA BODY

Data panel

Shutter-release button

Lens*

Self-timer lamp (p. 21)

Flash (p. 19)

Strap eyelet (p. 12)

Mode dial (main switch)

Viewfinder window*

Battery/card-chamber door (p. 10, 12)

Viewfinder*

LCD monitor*

(p. 17)

Menu button

DC terminal (p. 11)

Access lamp

Display button (p. 17)

Mode button (p. 18)

Controller

USB port (p. 43)

Flash sensor

Image-size button (p. 22)

A tripod socket is locat-

ed under the body near

the lens.

DATA PANEL

MODE DIAL

Auto-recording mode

Multi-function recording mode

Playback mode (p. 30)

Setup mode (p. 38)

This dial gives direct and

easy access to the cam-

era’s major modes. It

also acts as the main

switch.

VIEWFINDER

Focus frame

Focus lamp (green)(p. 14)

Flash lamp (red)(p. 19)

The focus and flash

lamps also indicate when

an image is being written

to the memory card (p.

51).

Autoflash (p. 19)

Red-eye reduction (p. 19)

Fill-flash (p. 19)

Night portrait (p. 20)

Flash cancel (p. 19)

Landscape/Night view (p. 20)

Macro (p. 20)

Self-timer (p. 21)

Mode indicators

Movie indicator (p. 26)

Black & white indicator (p. 29)

Image-size indicators (p. 22)

Battery-condition indicator

(p. 11)

Frame counter

(p. 22)

GETTING UP AND RUNNING

INSTALLING A CR-V3 LITHIUM BATTERY

Insert the lithium battery (3).

• Make sure the positive and negative battery terminals are

orientated as illustrated.

This digital camera uses one CR-V3 lithium battery. When replacing the

battery, the mode dial should always be in the off position.

Close the battery-chamber door and slide it up (4) to engage the safety catch.

• If the battery-chamber door is open or the battery is removed for more than fifteen

minutes, the date and time may reset. When the camera is turned on, the monitor

will automatically activate and prompt you to set the calendar and clock (p. 41).

Open the battery-chamber door by sliding the door down (1) to release the

safety catch; the door should spring open (2).

BATTERY

CARD

TTERY

CARD

INSTALLING AA BATTERIES

Although camera performance is better with lithium batteries, two AA-size

alkaline or Ni-MH batteries can be used in this camera. The use of Ni-MH

batteries are recommended over alkaline because of longer life.

Install the batteries as shown in the diagram; make sure the positive and

negative battery terminals are orientated correctly.

When using Ni-MH batteries, fully recharge them with a battery charger

suitable for complex electronic equipment. Please consult your vendor

about an appropriate charger.

GETTING UP

AND RUNNING

This section covers the basic operation of the camera. Please read the entire section before moving

on to other sections in the manual. When the camera is initially turned on, the date, time, and menu

language must be set, see page 13.)

BATTERY-CONDITION INDICATOR

Full-battery Icon – the battery is fully charged.

Exhausted battery warning – battery power is insufficient for camera opera-

tion. The shutter will not release. Replace the battery immediately.

Low battery warning – battery power is very low, but all functions are operational. The

battery should be replaced as soon as possible.

This camera is equipped with an automatic battery-condition indicator. When the camera is on, the

battery-condition indicator appears on the data panel. If the data panel is blank, the batteries may be

dead or installed incorrectly.

AC ADAPTER (SOLD SEPARATELY)

The AC adapter AC-3 allows the camera to be powered from an electrical household outlet. The AC

adapter is recommended when the camera is interfaced with a computer or during periods of heavy

use.

Do not change the power supply while the camera is on.

Always turn off the camera before changing between power supplies.

AUTO POWER OFF

To conserve battery power, the camera will turn off displays and unnecessary functions if an opera-

tion is not made within three minutes. To restore power to the camera, press the shutter-release but-

ton partway down or press the display button. The length of the auto-power-off period can be

changed on the setup menu (p. 38).

In a recording mode, the LCD monitor will turn off after one minute. This period cannot be changed.

To reactive the LCD monitor, press the display button (p. 17).

Insert the mini plug of the AC adapter into the DC terminal.

Insert the AC adapter plug into an electrical outlet.

GETTING UP AND RUNNING

INSTALLING AND REMOVING A MEMORY CARD

Insert the memory card all the way into the card slot and

then release(2). The card should catch in the slot.

• Insert the card so the face is toward the front of the

camera. Always push the card in straight, never at an

angle. Never force the card. If the card does not fit,

check that it is orientated correctly.

• If a MultiMediaCard is inserted incorrectly, it will lock,

but the card chamber door will not close.

To eject a memory card, press the card into the slot and

release (3). The card can now be pulled out.

Always turn off the camera and confirm the access lamp is

not lit before inserting or removing a memory card,

otherwise the card may be damaged, and data lost.

BATTERY

CARD

BATTERY

CARD

Close the battery-chamber door and slide it up (4) to engage the safety

catch.

Open the battery-chamber door by sliding the door down

(1) to release the safety catch; the door should spring

open.

ATTACHING THE HAND STRAP

Pass the small loop through the strap eyelet on the

body (1).

Pass the other end of the strap through the small

loop and tighten (2).

Always keep the strap around your wrist in the event

that the camera is accidentally dropped.

Access lamp

An SD (Secure Digital) Memory card or MultiMediaCard must be inserted for the camera to operate.

If a card has not been inserted, three zeros (000) will blink on the data-panel frame counter. For

more about memory cards, see page 7.

SETTING UP THE CAMERA

When the camera is initially turned on, the

LCD monitor will activate and prompt you to

set the menu language and the date and

time. Turn the camera on by setting the mode

dial to the setup position.The

controller is used to make settings on the

LCD monitor.

JAPANESE

FRANCAIS

DEUTSCH

ENGLISH

Would you like to select

ENGLISH ?

YES

Date/Time set

00:00

2001

Year

Month

Day

Use the up/down key of the controller to

highlight the desired language.

To select the language, press the center of

the controller. A confirmation screen will

appear.

On the confirmation screen, use the left/right

key to select “YES.”

• Choosing “NO” will cancel the operation

and return to the language selection

screen.

Press the center of the controller to execute

the command.

After the language is set, the date/time screen will appear automatically. Please take time to accu-

rately set the clock and calendar; when an image is taken, the date and time of capture is recorded

with it.

Use the up/down key to highlight in red the

setting to be changed.

• When the hour is highlighted, pressing the

down key will highlight the minutes.

Use the left/right key to change the highlight-

ed setting.

When the date and time have been set,

press the center of the controller.

• A confirmation screen will appear. Use the left/right key to select “YES”; choosing “NO” will cancel

the operation and return to the date/time screen. Press the center of the controller to to execute the

command on the confirmation screen. If an error was made setting the language or date, they can

be reset on the setup menu (p. 38).

Controller

GETTING UP AND RUNNING

This camera is equipped with a zoom lens. The effect of

the zoom is visible in the viewfinder and on the LCD

monitor. To activate the LCD monitor, simply press and

hold the display button.

The controller is used to zoom the lens.

Pressing the up key of the controller zooms the

lens toward the telephoto position (T). The

down key zooms towards the wide-angle posi-

tion (W).

USING THE ZOOM LENS

Controller

Display button

Center the subject within the viewfinder focus frame.

• For off-center subjects, use the focus-lock function (p. 15).

• Make sure the subject is within the focus range of the lens:

0.8m – '. For subjects closer than 0.8m, use the macro

function (p. 20).

• The actual autofocus sensor is located in a

small area within the focus frame as

illustrated on the right by the shaded box.

Press the shutter-release button partway down (1) to lock the focus and exposure.

• The green focus lamp next to the viewfinder will glow to confirm that the image

is in focus. If the focus lamp blinks, the camera was unable to focus on the

subject. Repeat the previous steps until the lamp is

steady.

Press the shutter-release button all the way down (2) to take the pic-

ture.

• Both the focus and flash lamps will glow indicating the image data

is being written to the memory card. Never

remove a memory card while data is being

transferred.

• After an image in recorded, it can be

played back for three seconds by activating

the instant-playback function on the setup menu (p. 38, 41)

With the mode dial set to auto recording, the camera will turn on and the lens

will automatically extend. If the lens is hindered when extending, an error mes-

sage (Err) will appear on the data panel; turn the camera off and wait for the

lens to retract.

BASIC RECORDING OPERATION

SPECIAL FOCUSING SITUATIONS

The camera may not be able to focus in certain situations. If the autofocus system cannot focus on a

subject, the green focus lamp will blink. In this situation the focus-lock function can be used to focus

on another object at the same distance as your main subject, and then the image can be recom-

posed to take the picture.

The subject in the

focus frame is low in

contrast.

The subject is too dark. Two subjects at differ-

ent distances overlap

in the focus frame.

The subject is near a

very bright object or

area.

FOCUS LOCK

The focus-lock function is used when the subject is off-center and outside the focus frame. Focus

lock may also be used when a special focusing situation prevents the camera from focusing on the

subject. This function is controlled with the shutter-release button.

Center the subject within the focus

frame. Press and hold the shutter-

release button partway down.

• The green focus lamp will glow to

indicate that the focus is locked.

Without lifting your finger from the

shutter-release button, recompose

the subject within the image area.

Press the shutter-release button all

the way down to take the picture.

While using the viewfinder or LCD monitor, grip the camera firmly with your

right hand while supporting the body with your left hand. Keep your elbows at

your side and your feet shoulder-width apart to hold the camera steadily. When

taking vertical pictures, hold the camera so that the flash is above the lens with

the grip to the top. Take care not to cover the lens with your fingers or the

strap.

HANDLING THE CAMERA

GETTING UP AND RUNNING

VIEWING PICTURES

Still images can easily be viewed in playback mode. To view images, turn the

mode dial to the playback position (1).

Simply use the controller to scroll through the pictures on the memory card.

Images are displayed with date, frame number, and image size information.

The date is temporarily displayed with each new image.

Use the left/right key of the controller to

scroll through the images.

In playback mode, a still image can be enlarged by 2X for closer examination.

Controller

With the image to be enlarged displayed, press the center of

the controller.

• The degree of magnification is displayed on

the LCD monitor.

Date of recording

Frame number (p. 22)Image size (p. 22)

ENLARGED PLAYBACK

When enlarged, the

image can be scrolled

using the four-way key of

the controller.

• To exit the enlarged

playback, press the

controller again.

• Enlarged images are framed with a

blue border.

CAMERA CONTROLS

AUTO-RECORDING AND

MULTI-FUNCTION RECORDING MODE

Thoroughly familiarize yourself with the getting up and running section before moving on to this sec-

tion. The previous section covers the basic operation of the camera.

In this section, button controlled recording functions are described. Unless noted, the functions in this

section are the same for the auto-recording and multi-function recording mode.

TURNING ON THE LCD MONITOR – THE DISPLAY BUTTON

Display button

To turn on the LCD monitor, simply press the display but-

ton until the monitor activates. The button is also used to

turn the monitor off.

To conserve power, the monitor automatically turns off

after one minute if an operation is not made. The monitor

can be reactivated using the display button. The display

button also reactivates the camera when it is shut down

with the auto-power-save function (p. 11).

The use of the monitor will reduce battery life. To con-

serve power, use the viewfinder.

The mode button gives quick, easy access to the camera’s

flash modes and subject programs. By pressing the mode

button, the mode indicators point to the active mode. To

cycle through the modes in reverse order, press and hold

the mode button and use the left key of the controller to

change the modes. When the camera is turned off, the

mode is reset to autoflash. The mode can also be reset to

autoflash by pressing and holding the mode button for

about two seconds.

Four flash modes are available: autoflash, autoflash with

red-eye reduction, fill-flash, and flash cancel (p. 19). Three

subject programs can be chosen: night portrait, land-

scape/night view, and macro (p. 20). Subject programs opti-

mize the camera’s performance for certain subjects. Each

of the flash modes and subject programs has two posi-

tions, one with the mode alone and one with the self-timer

(p. 21). The mode button cannot be used with movie

recording (p. 26).

MODE BUTTON

CAMERA CONTROLS

Mode button

Self-timer w/ macro mode

Self-timer w/ landscape mode

Self-timer w/ flash cancel

Self-timer w/ night portrait mode

Self-timer w/ fill-flash

Self-timer w/ red-eye reduction

Self-timer w/ autoflash

Macro mode

Landscape/Night view mode

Flash cancel

Night portrait mode

Fill-flash

Autoflash w/ red-eye reduction

Autoflash

• When the auto-power-off function activates (p. 11), all the modes remain in effect except for night

portrait, macro, and self-timer.

Autoflash

Fill-flash

Flash cancel

Autoflash with

red-eye reduction

Autoflash – the flash fires automatically in low-light

and backlit conditions.

Red-eye reduction – the flash fires several times

before the main flash burst to reduce red-eye; the

effect is caused by light reflected from the retina.

Used in low-light conditions when taking pho-

tographs of people or animals. The pre-flashes con-

tract the pupils of the subject’s eyes.

Flash cancel – the flash will not fire. Use flash cancel when flash photography is prohibited, natural

light is desired to illuminate the subject, or the subject is beyond the flash range. The camera-shake

warning may appear when flash cancel is selected (p. 20).

Fill-flash – the flash fires with each exposure

regardless of the amount of ambient light. Fill-flash

can be used to reduce harsh shadows caused by

strong direct light or sunshine.

FLASH MODES

To set the flash mode, simply press the mode but-

ton on the back of the camera until the desired

mode is displayed (p. 18).

FLASH RANGE

The camera will automatically control the flash output. For well-exposed images, the subject must be

within the flash range. Because of the optical system, the flash range is not the same at the lens’

wide-angle position as it is at the telephoto position.

Wide-angle position

Telephoto position

0.8m ~ 3.0m (2.6 ft. ~ 9.8 ft.)

0.8m ~ 2.0m (2.6 ft. ~ 6.6 ft.)

FLASH SIGNALS

The red flash lamp next to the viewfinder

indicates the status of the flash when the

shutter-release button is pressed partway

down. When the lamps glows, the flash is

charging and the shutter will not release.

When the lamp is not lit, the flash is

charged and ready to fire.The flash lamp is

also used as a camera-shake warning, see

page 20.

Fill-flash

CAMERA CONTROLS

SUBJECT PROGRAMS

The subject-programs optimize the camera’s performance for various conditions and subjects.

Subject-programs are set with the mode button (p. 18). A pointer will indicate the active subject pro-

gram, which will remain in effect until it is changed or the camera is turned off.

Macro – Used for close-up photography between 25 and 80

cm (9.5 ~ 31 inches) from the front of the lens. The LCD moni-

tor should be used to compose the picture rather than the

viewfinder; press and hold the display button to activate the

monitor. The flash will not fire in macro mode; the camera-

shake warning may appear in low-light conditions.

Landscape / Night view – Optimized to produce sharp,

colourful landscapes during the day or at night. The flash will

not fire in this mode. The camera-shake warning may appear

in low-light conditions. When taking pictures of landscapes at

night, long exposures are required; the use of a tripod is rec-

ommended.

Night portrait – For portraits with subtle night scenes. The

flash output is balanced with the ambient light exposure so

that the subject and background are visible. Red-eye reduction

is used with night portrait (p. 19). Ask your subject not to move

after the flash burst; the shutter will still be open for the back-

ground exposure. Make sure the subject is within the flash

range: 0.8 – 3.0m (wide-angle position), 0.8 – 2.0m (telephoto

position).

CAMERA-SHAKE WARNING

If the shutter speed falls below the point where the

camera can be safely hand held, the red flash lamp

will blink. Camera shake is slight blurring caused by

subtle hand motion and is more pronounced at the

telephoto position of the lens than at the wide-angle.

Although the warning appears, the shutter can still

be released. If the warning appears, place the cam-

era on a tripod or, if the subject is within the flash

range (p. 19), use the built-in flash. The camera-shake warning only appears in the flash cancel (p.

19), landscape, and macro modes.

Page is loading ...

KONICA Dimage E203 User manual

Brand: KONICA

Model: Dimage E203

Type: User manual

This manual is also suitable for

DIMAGE E203 - SOFTWARE

Download PDF

report

KONICA Dimage E203 User manual

This manual is also suitable for

KONICA Dimage E203 User manual

Related papers

Other documents