Renkforce RF-POE-1000 Owner's manual

Brand: Renkforce

Model: RF-POE-1000

Type: Owner's manual

Page is loading ...

• Always lay the cables so that nobody can trip over or become entangled in them.

This poses a risk of injury.

• For safety reasons, disconnect the power adapter from the mains socket during storms.

• Ensure there is sufcient air circulation when you operate the product. Never

cover the product.

• Do not touch the power adapter if there are any signs of damage, as this may

cause a fatal electric shock! Switch off the mains voltage to the socket containing

the power adapter (switch off the corresponding circuit breaker or remove the

safety fuse, and then switch off the corresponding RCD protective switch). You

can then unplug the power adapter from the mains socket. Dispose of the faulty

power adapter in an environmentally friendly manner and discontinue its use.

Replace it with a power adapter of the same design.

• Never pour liquids over electrical devices or place objects lled with liquid next to

the device. If liquid or a foreign object enters the interior of the device nevertheless,

rst power down the respective mains socket (e.g. switch off the circuit breaker)

and then pull the mains plug from the mains socket. Do not operate the product

any more afterwards, but take it to a specialist workshop.

• Never use the product immediately after it has been brought from a cold room into a

warm one. The condensation that forms may destroy the product. The power adapter

may also cause a fatal electric shock! Allow the product to reach room temperature

before connecting it and putting it into use. This may take several hours.

• Consult a technician if you are not sure how to use or connect the product, or if

you have concerns about safety.

• Maintenance, modications and repairs must only be carried out by a technician

or a specialist repair centre.

• If you have any questions that are not answered in these operating instructions,

please contact our technical customer service or other professionals.

Product overview

1 32 4

1 LAN input LAN IN (Data)

2 LED indicator light PWR

3 Connection socket DC 48V

4 LAN output POWER+DATA OUT (PoE and data)

Connection diagram

PoE InjectorPower Socket Ethernet device

(switch, router, etc.)

LAN IN

PWR

DC 48V

IP Camera AP IP Phone

Powered Device (PD)

Setup

• Place the product on a levelled and clean surface.

• Connect the round plug of the included power adapter to the DC 48V connection socket (3).

Connect the power adapter to a suitable mains socket. The PWR LED indicator light (2) lights

up yellow, indicating that the power supply is operating normally.

• Connect a compatible RJ45 network cable (twisted pair, max 100 m per cable) to the LAN

input LAN IN (1).

• Connect a compatible RJ45 network cable (twisted pair, max 100 m per cable) to the LAN

output POWER+DATA OUT (4). You can connect an IEEE 802.3 compatible device (such as

an IP camera) to the other end of the network cable. A total of 12.95 W are available. Note

the "Technical data" section.

• As soon as the connection is active, the LED indicator PWR will turn solid red, indicating that

an electrically powered device has been detected and the power is normal.

• Disconnect all connected devices from the product after use. Disconnect the power adapter

from the mains socket after use. The LED indicator light goes out after a few seconds.

Operating instructions

PoE injector

Item no. 1954688

Intended Use

The product is used for power supply (PoE - Power over Ethernet) on a LAN output with

simultaneous data transmission. Power is supplied via the supplied adapter. The product can

power an existing network cable with compatible IEEE 802.3af PD compliant devices. The

product is compatible with "Smart Plug and Play". The LAN output has an output limitation of

max. 12.95 W and is protected against short circuits.

This product is intended for indoor use only. Do not use it outdoors. Contact with moisture

(e.g. in a bathroom) must be avoided under all circumstances.

For safety and approval purposes, do not rebuild and/or modify this product. Using the product

for purposes other than those described above may damage the product. In addition, improper

use can cause hazards such as a short circuit, re or electric shock. Read the instructions

carefully and store them in a safe place. If you pass the product on to a third party, please hand

over these operating instructions as well.

This product complies with statutory, national and European regulations. All company and

Delivery content

• PoE injector

• Power adapter

• Operating instructions

Up-to-date operating instructions

Download the up-to-date operating instructions at www.conrad.com/downloads or scan the QR

code shown. Follow the instructions on the website.

Explanation of symbols

The symbol with the lightning in a triangle indicates that there is a risk to your health,

e.g. due to an electric shock.

The symbol with an exclamation mark in a triangle is used to highlight important

information in these operating instructions that must be observed.

Safety instructions

Read the operating instructions carefully and observe in particular the safety

instructions. If you do not follow the safety information and information on

proper handling in these operating instructions, we will assume no liability for

any resulting personal injury or damage to property. Such cases will invalidate

the warranty/guarantee.

• The device is not a toy. Keep out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. It may become a

dangerous plaything for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height

may damage the product.

• Always observe the safety instructions and operating instructions of any other

devices which are connected to the product.

• The mains outlet must be located near to the device and be easily accessible.

• Only power the product using the power adapter provided.

• Only connect the power adapter to a normal mains socket connected to the public

supply. Before plugging in the power adapter, check whether the voltage stated on

the power adapter complies with the voltage of your electricity supplier.

• Never connect or disconnect power adapters if your hands are wet.

• Never unplug the power adapter from the mains socket by pulling on the cable;

always use the grips on the plug.

• When setting up the product, make sure that the cables are not pinched, kinked

or damaged by sharp edges.

Care and cleaning

• Disconnect the product from the mains socket and connected devices before cleaning.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may

damage the case or cause the product to malfunction.

• Do not immerse the product in water or other liquids.

• Use a dry, lint-free cloth to clean the product.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste. At the end of its service life, dispose of the product in accordance

with applicable regulatory guidelines.

You thus full your statutory obligations and contribute to environmental protection.

Technical data

a) PoE injector

Output voltage/current ............. 48 V/DC, 0.5 A

PoE output ...............................max. 12.95 W (IEEE 802.3af)

IEEE Standard ......................... IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3af

Ports (RJ45) ............................1 10/100/1000Mbps LAN data input,

1 10/100/1000Mbps LAN Data/Power output (PoE)

Network media .........................10BASE-T: UTP category 3, 4, 5 cables (max 100 m),

EIA/TIA-568 100Ω STP (max 100 m)

100BASE-TX: UTP category 5, 5e cables (max 100 m)

EIA/TIA-568 100Ω STP (max 100 m)

1000BASE-T: UTP category 5, 5e, 6 cables (max 100 m)

Operating conditions ................0 to +40 °C, 10 – 90 % RH (non-condensing)

Storage conditions ................... -40 to +70 ºC, 5 – 90 % RH (non-condensing)

Dimensions (W x H x D) ..........54 x 24 x 80.8 mm

Weight .....................................approx. 58 g

b) Power adapter

Input voltage / current .............. 100 - 240 V/AC, 50/60 Hz, 0.8 A

Output voltage / current ........... 48 V/DC, 0.5 A

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming or capturing in

electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is

prohibited. This publication reects the technical status at the time of printing.

Page is loading ...

Renkforce RF-POE-1000 Owner's manual

Brand: Renkforce

Model: RF-POE-1000

Type: Owner's manual

Download PDF

report

in other languages

français: Renkforce RF-POE-1000 Le manuel du propriétaire
Deutsch: Renkforce RF-POE-1000 Bedienungsanleitung
Nederlands: Renkforce RF-POE-1000 de handleiding

Renkforce RF-POE-1000 Owner's manual

Renkforce RF-POE-1000 Owner's manual

in other languages

Related papers

Other documents