Sony NV Series NV-U70 Quick start guide

NV-U70

Personal Navigation System

Owner's Record

The model and serial numbers are located on the bottom of the main unit.

Record the serial number in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer

regarding this product.

Model No. NV-U70 Serial No.________________________

Quick Start Guide

2-663-630-21 (1)

ES

US

FR

Guide de démarrage

rapide

Guía de inicio rápido

2

No guarantee for lost data or

damaged data

Sony does not provide any guarantee for lost or

damaged data.

Caution

IN NO EVENT SHALL SONY BE LIABLE

FOR ANY INCIDENTAL, INDIRECT OR

CONSEQUENTIAL DAMAGES OR OTHER

DAMAGES INCLUDING WITHOUT

LIMITATION LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE

OF THE PRODUCT OR ANY ASSOCIATED

EQUIPMENT, DOWNTIME, AND

PURCHASER’S TIME RELATED TO OR

ARISING OUT OF THE USE OF THIS

PRODUCT, ITS HARDWARE AND/OR ITS

SOFTWARE.

Welcome !

Thank you for purchasing this Sony Personal

Navigation System. Before operating this

system, read this manual thoroughly and retain it

for future reference.

FEATURING:

• Plug & Play capability

• Pre-installed US map

• Canada map available on Application Disc

• 15 languages selectable for voice guidance and

on-screen display

• 3.5-inch high quality display with touch screen

• Advanced 12ch parallel GPS receiver

• High-quality speaker

• Battery operation

• Auto dimmer function

Warning

If you have any questions about this product, you

may contact:

Sony Customer Information Services Center

Call: 1-(800)-222-7669

Address: 12451 Gateway Blvd., Fort Myers,

FL 33913

URL: www.sony.com/nav-u/support

About this manual

• This Quick Start Guide contains instructions

for installation, connections and basic

operations. For more information, see the

PDF manual on the supplied Application

Disc.

• Contents of this manual are written for users

with knowledge of using the Microsoft®

Windows® operating system. For details

about computer operation, see the manual

for your computer.

• Illustrations in this manual may differ from

the actual device.

• Retain this manual in a place where you can

refer to at any future time.

Declaration of Conformity

Trade Name: Sony

Model No.: NV-U70

Responsible Party: Sony Electronics Inc

Address: 16450 W. Bernardo Dr,

San Diego, CA 92127

USA

Telephone number: 858-942-2230

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one or more of the following

measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment

and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

– Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

3

Table of Contents

Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Getting Started 6

Checking the contents . . . . . . . . . . . . . . . . . . . . 6

Installing the unit. . . . . . . . . . . . . . . . . . . . . . . . 7

Location of controls. . . . . . . . . . . . . . . . . . . . . 11

Turning the unit on . . . . . . . . . . . . . . . . . . . . . 12

Starting up the navigation . . . . . . . . . . . . . . . . 12

Receiving GPS signals . . . . . . . . . . . . . . . . . . 12

Basic Operations 13

Menu operations . . . . . . . . . . . . . . . . . . . . . . . 13

Keyboard operations . . . . . . . . . . . . . . . . . . . . 13

Route Searching 14

Setting the destination and

starting guidance . . . . . . . . . . . . . . . . . . . . . 14

Other ways to set the destination. . . . . . . . . . . 15

Guidance displays . . . . . . . . . . . . . . . . . . . . . . 16

System Settings 17

Using the Supplied Software 18

Connecting to your computer. . . . . . . . . . . 18

Software features . . . . . . . . . . . . . . . . . . . . 19

Additional Information 19

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Notes on unit disposal. . . . . . . . . . . . . . . . . . . 19

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 20

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 21

Resetting the unit . . . . . . . . . . . . . . . . . . . . 21

4

Warning

PLEASE READ THIS MANUAL

COMPLETELY BEFORE INSTALLING OR

OPERATING YOUR PERSONAL

NAVIGATION SYSTEM. IMPROPER

INSTALLATION OR USE OF THIS DEVICE

MAY CAUSE ACCIDENT, INJURY OR

DEATH.

On safety

•Be sure to:

– install the navigation system in a safe place

where it does not obstruct the driver’s view.

– not install the unit above an airbag.

– place the cables where they do not obstruct

driving.

Failure to do so may result in unsafe driving

conditions.

• Be sure to attach the unit to the cradle properly,

otherwise the unit may fall.

• Be sure to clean the surface of the suction cup and

windshield before attaching. Also, confirm that

the suction cup is securely attached to the

windshield after installation. Otherwise, the unit

or cradle may fall.

• Do not apply excessive force to the unit or cradle

as it may fall.

• If ambient temperature is low, warm up the car

interior and then install the cradle and unit. The

cup suction is affected at high/low temperatures or

sudden changes in temperature, and the unit or

cradle may fall.

• Should condensation occur inside the car, wipe the

windshield before installation, as the suction cup

may come off, and the unit or cradle may fall.

• Observe all traffic rules and regulations, such as

one-way streets, while driving with the route

guidance.

• Comply with your local traffic laws and

regulations.

• Do not continuously watch the unit while driving.

It is dangerous and may cause a traffic accident.

• If you need to operate the navigation system while

driving, be sure to stop the car in a safe place

before operating.

• For your safety, do not mount or remove the unit

from the cradle while driving.

• When mounting the unit in the cradle, remove any

supplied accessories, such as USB cable, etc.,

from the unit. They may fall or their cables may

interfere with driving.

• Do not modify the unit.

• Do not disassemble the unit except when

disposing of it.

On handling

• Do not let foreign objects get inside the cradle

connector of the unit, as it may cause malfunction.

• Turn the unit off by pressing ?/1 and keep it in the

standby mode when not in use. Turning the

ignition off does not turn off the unit, which

continues to draw power from the lithium-ion

rechargeable battery (built-in).

• Turn the unit off by pressing ?/1, take it out of the

cradle, then disconnect the car battery adapter,

otherwise it may drain the car battery. Note the

following.

– If your car’s cigarette lighter socket is not

connected to the ignition switch ACC position,

power continues to be supplied to the built-in

battery, even if you turn the ignition off.

– Check the CHG indicator at the bottom right of

the unit which lights up during charging.

• Do not place anything other than the specified unit

in the cradle.

• Do not connect any accessory (car battery adapter,

AC power adapter, etc.) other than those supplied

or optional.

• Do not expose the unit to fire or water, as it may

cause a malfunction.

• Do not let water or rain get into the unit, as it may

cause a malfunction.

• Do not allow any liquid or foreign object to enter

the unit.

• Be sure to remove the unit out of the cradle when

leaving your car to prevent theft or high

temperature damage inside the car.

• If you leave the unit in direct sunlight, the LCD

may darken and not display clearly. This is not a

malfunction, and it will return to normal as

temperature decreases.

• Note that the built-in battery cannot be charged

outside the temperature range 5 – 45 ºC (41 – 113

ºF).

• Do not leave the unit in high ambient temperature

as the built-in battery capacity will deteriorate, or

it will become unchargeable.

• When the car battery adapter is not in use,

disconnect it from the cigarette lighter socket, as it

may drain the car battery even with ignition OFF.

C

H

G

R

E

S

E

T

P

O

W

E

R

O

F

O

N

Cradle

connector

?/1

5

On installation

• Before installing the unit, check your local traffic

laws and regulations.

• Make sure you install the unit properly according

to the installation instructions. Improper

installation may result in fire or electric shock.

• Before installation, be sure to turn the ignition

switch to the OFF position or take out the key.

Installing the unit with the ignition on may cause

the car battery to drain or short circuit.

• For information about the polarity, battery voltage

and location of the airbag in your car, please

consult your car dealer.

• When installing the unit, use only the hardware

provided and avoid mounting to any critical

components of the vehicle.

• Take care to prevent cords or wires from getting

tangled or crimped in the moving portion of a seat

rail.

Mounting location

• Do not install the cradle where:

– it will obstruct the driver’s view when the cradle

is mounted in the car, or the unit is in the cradle.

– it will obstruct the operation of the airbag

system.

– it will obstruct the operation of the car,

especially the steering wheel, shift lever, or

brake pedal.

– it will be subjected to heat/high temperature.

• Please consult a qualified technician or service

personnel if you cannot attach the cradle to the car

securely.

On GPS

GPS (Global Positioning System) satellites

continuously emit signals for positioning anywhere

on the earth. As a GPS antenna receives these

signals, users can be informed of their location

(latitude, longitude and altitude). Information must

be received from 3 satellites in order to obtain two-

dimensional fixes (latitude and longitude), and 4

satellites are required for three-dimensional

positioning (latitude, longitude and altitude). As

GPS satellites are controlled by the U.S. Department

of Defense, a deliberate margin of error between a

few meters (a few feet) and 10 meters (32.8 feet)

exists. As a result, the GPS navigation system may

include an error of between 10 meters (32.8 feet)

and about 200 meters (656.2 feet), depending on the

circumstances.

As GPS information is obtained using signal from

satellites, it may be impossible or difficult to obtain

the information in the following locations:

• Tunnel or underground

• Under a highway

• Between high buildings

• Between tall trees with dense foliage

After the initial installation, park your car in a safe,

open place (no high buildings, etc.) for up to 20

minutes to allow for GPS signals to be received

before using the navigation system. The system

requires signals from a minimum of 3 GPS satellites

to calculate the current car position properly.

Note

It takes time to receive a GPS signal when switching

the unit ON after switching OFF the main power, after

the built-in battery is fully discharged, or after resetting

the unit.

On the software

Read the following conditions carefully before use.

• Copyright laws prohibit reproducing the software

or the software manual in whole or in part or

renting the software without the permission of the

copyright holder.

• In the event a problem occurs with this software as

a result of defective manufacturing, Sony will

replace it at Sony’s option or issue a refund.

However, Sony bears no other responsibility.

• The software provided with this product cannot be

used with equipment other than that which it is

designated for use with.

• Please note that, due to continued efforts to

improve quality, the software specifications may

be changed without notice.

• Roads and names on the map may differ from

actual roads and names.

• The warranty does not extend to an exchange or

refund due to some typographical errors and

omissions, or any other discrepancy in layout

found in the software.

• In no way may the map data be copied and used,

in whole or in part, without permission of the

copyright holder.

• Contents are subject to change without notice.

By using the unit, you are agreeing to be bound by

the above.

6

Getting Started

Checking the contents

Check the package contents.

• Main unit

•Cradle

• Car battery adapter

• AC power adapter

• AC power cable

• USB cable

• Mounting plate

•Screws (3)

•Adhesive tape

•Pad

• Carrying pouch

• Application Disc (DVD-ROM)

• Quick Start Guide

• Read This First

• Warranty card

• END-USER LICENSE AGREEMENT

7

Installing the unit

About the main power switch

Before installation, switch on the main power by

sliding the POWER switch to the ON position.

Thereafter, you can turn the unit on/off by

pressing

?/

1

on the top right of the unit.

Notes

• Keep main power on unless the unit is not to be

used for more than 3 months.

• If you switch off the main power, it may take time to

receive GPS signals when switching on again.

About the suction mount

Before you start, choose a position on the

windshield that is clearly visible to the driver

without obstructing the road view, and make sure

all surfaces are clean and dry.

The optional cradle NVA-CU3 can also be

installed following the steps below.

Notes

• Install the unit in a safe place where it does not

interrupt the GPS signal.

• Detach and reattach the cradle regularly as cup

suction is affected by high/low temperature,

extended use, etc.

• Be sure to keep a distance between the cradle and

dashboard when installing.

1 Attach the cradle on the windshield.

Figure example of completed cradle

installation

Follow steps 1 - 3 to complete.

1 Clean and dry the surface of the suction

cup.

2 Press the center of suction cup firmly

against the windshield to remove the

remaining air inside it, then press the lever.

3 Holding the left knob*, loosen the right

knob and set the approximate vertical

angle, then retighten.

*The left knob does not turn.

Check that the installation method complies

with local traffic laws and regulations before

installing and operating the unit.

The unit can either be installed on a

windshield (page 7), or a dashboard with the

supplied mounting plate and screws (page 9).

POWER

ONOFF

C

H

G

R

E

S

E

T

POWER

OFF

ON

continue to next page t

x

To tighten

To loosen

8

If you want to fix the cradle on the

windshield permanently

The suction cup is affected in high/low

temperatures and may come off. If you want

to fix the cradle on the windshield

permanently, use the supplied adhesive tape

on the suction cup.

If the bottom of the cradle touches the

dashboard

Attach the supplied pad for protection.

Cut the pad to the appropriate size before

attaching.

Note

The adhesive tape is difficult to remove once

applied.

2 Connect the cradle to the car cigarette

lighter socket.

1 Plug the car battery adapter into the DC IN

5.2V jack at the rear of the cradle.

2 Insert the other end of the car battery

adapter fully into the car cigarette lighter

socket.

*Lights up when you turn the ignition on after

installation.

Note

Depending on the size or shape of the cigarette

lighter socket, connection may not be possible.

3 Align the 2 slots on the underside of

the unit with the tabs on the cradle,

then push to snap the unit into place.

Be sure the unit is securely locked in the

cradle (2 clicks).

4 Loosen the center knob, fine adjust

the angle so you can view the monitor

properly, then retighten.

Tip

You can also connect the unit to an outlet using the

supplied AC power adapter.

D

C

IN

5

.2

V

LED*

1st click

2nd click

To tighten

To loosen

9

To detach the unit from the cradle

1 Holding the unit, press the RELEASE

button of the cradle.

The unit pops out of the cradle.

2 Take the unit out of the cradle.

About the installation on the

dashboard

Note

The adhesive tape is difficult to remove once applied,

and the screw will mark the dashboard. Choose a

position carefully before installation.

1 Choose a position to attach the

mounting plate on the dashboard, then

clean and dry the surface of the

dashboard.

2 Remove the cover of the adhesive

tape, then firmly press down the

mounting plate on the dashboard.

3 Secure the supplied 3 screws of the

mounting plate using a screwdriver.

C

H

G

R

E

L

E

A

S

E

continue to next page t

1

2

Mounting plate

Adhesive tape

10

4 Attach the cradle on the mounting

plate.

1 Clean and dry the surface of the suction

cup.

2 Press the center of the suction cup firmly

down on the mounting plate, then press the

lever.

3Holding the left knob*, tighten the right

knob.

*The left knob does not turn.

If you want to fix the cradle on the mounting

plate more securely to prevent risk of

dropping, use the supplied adhesive tape on

the suction cup.

Follow steps 2 to 5 of “About the suction

mount” on page 7, to complete the

installation.

x

11

Location of controls

Front:

Rear:

Refer to the pages listed for details.

a VOICE/POSITION button

During route guidance:

To hear the next voice guidance.

In map scrolling mode:

To show your current car position.

b Speaker

Outputs guidance and warnings.

c Display window/touch screen

d ?/1 (on/standby) button 12

To turn the unit on/off.

e CHG (battery charge) indicator 8

Lights up in red while charging.

f USB jack 18

To connect to a computer with the USB

cable.

g Auto dimmer sensor

For details on auto dimmer function, see the

supplied PDF manual.

h DC IN 5V jack

To connect to the AC power adapter.

i POWER switch 7, 21

To turn the main power on/off.

j External GPS antenna* jack

k RESET button 21

l Cradle connector

* Not supplied

VOICE/

POSITION

C

H

G

1

2

3

5

4

Built-in GPS antenna

D

C

IN

5

V

POW

ER

OFF

ON

R

E

S

E

T

2

6

8

7

9

qa

0

qs

Jack cover

12

Turning the unit on

Check that the POWER switch on the bottom

right of the unit is in the ON position

beforehand (page 7).

1 Press ?/1.

To turn the unit off

Press ?/1.

The unit enters standby mode for minimum

power consumption.

Note

Be sure to take the unit out of the cradle and

disconnect the car battery adapter when the unit is not

in use to prevent car battery drain.

Starting up the navigation

1 After turning the unit on, touch the

desired language.

The warning display appears.

2 Read the warning display, then touch

“Agree.”

The tutorial displays appear.

3 Touch V to proceed.

The top menu appears.

Receiving GPS signals

After the initial installation, park your car in a

safe, open place (no high buildings, etc.) for up

to 20 minutes to allow for GPS signals to be

received before using the navigation system. The

system requires signals from a minimum of 3

GPS satellites to calculate the current car

position properly.

You can check the GPS status on displays.

* Lights up in bright green when signal reception is

sufficient for navigation.

Lights up in dark green when signal has been lost.

GPS status indicator*

13

Basic Operations

Common procedures to operate the system are

explained.

General operations can be performed on the

touch screen. Touch the displayed icons with

your finger gently.

Note

Do not press the display with excessive force, or use

any sharp article, such as a pen, etc., to tap on the

display.

Menu operations

You can set items in the menu by the following

procedures.

1 Show the top menu.

In the map display, touch the map.

In the menu display, touch to show the

map, then touch the map.

2 Touch “Settings,” then touch a desired

item.

3 Touch v/V to scroll the list, then touch

a desired setting item.

E.g.: Volume setting display

4 Make the desired setting.

Touch and select the desired setting or input

characters.

During menu operation:

To return to the previous display, touch .

To cancel the menu selection, touch (the

current car position display appears).

Note

The items on the menu and setting operations differ

depending on the selected menu item.

Keyboard operations

The keyboard display appears when you need to

enter text.

You need only enter characters in upper case, as

the system automatically converts them to

appropriate characters. You can enter special

characters when necessary (e.g. when naming a

saved destination, etc.).

Mobile phone keyboard display

To Touch

enter an alphabetical

character

the relevant key (e.g.

“ABC”) repeatedly until

the desired character is

highlighted in the line

above the keyboard.

enter a number “NUM” to switch to the

number keyboard, then

the desired number key;

and “ABC” to switch

back.

enter a space “_”

delete a character “T”

select a candidate v/V to scroll the list,

then the desired

candidate to confirm.

see the list of all

candidates

“List”

continue to next page t

Candidates

14

You can select either a mobile phone keyboard or

a character keyboard (alphabetical) for the

keyboard display.

Touch to switch to character keyboard.

The character keyboard is used in the same way

as the mobile phone keyboard, except when:

– entering a character (touch the desired

character key).

– entering a special character (touch “SYM” to

switch to the special character keyboard; touch

“ABC” to switch back).

Touch to switch back to the mobile phone

keyboard.

Route Searching

The system searches for routes automatically

after setting the destination.

Before starting, check that GPS signals are

sufficient for navigation (

page 12).

Setting the destination and

starting guidance

The procedure for searching for the route and

starting route guidance is explained.

As an example, setting the destination by the

address is introduced here.

For details on setting the destination in other

ways, see “Other ways to set the destination” on

page 15.

For your safety, park your car in a safe place,

then enter the destination information before

starting a journey.

1 Show the top menu.

In the map display, touch the map.

In the menu display, touch to show the

map, then touch the map.

2 Select “New Destination” c

“Navigation.”

3 Select the desired region by touching

the “Region” entry field.

Only regions included in the current map data

are selectable.

4 Select “Address.”

15

5 Input the address details.

For details on how to input characters, see

“Keyboard operations” on page 13.

Touch the respective entry field to input the

items below.

6 Select “Start navigation.”

The route option selection display appears.

For details on selecting route options, see the

supplied PDF manual.

7 Select “Start navigation” again.

The map display appears, the route is

calculated, and route guidance starts.

Other ways to set the

destination

You can also set the destination and search for

routes using the following methods.

From the top menu, select the items in the

following order, then “Start navigation” (if

necessary).

For details, see the supplied PDF manual.

“City or ZIP”

Input the city name or ZIP code.

“Street”/“–”

Input the street name, and house number (if

known).

If no house number is available, the “–” field

is deactivated.

“Intersection”

Input the crossroad name if you want it as the

destination point.

Search nearby

Searches for routes to a POI, such as restaurant,

hotel, etc., near the current car position.

Home

Searches for routes to your home when it is

registered.

“New Destination” c “Home”

Point of interest

Searches for routes to a POI, such as restaurant,

hotel, etc., by selecting the category(ies) and

correct destination from the list.

Select “New Destination” c “Navigation” c

“Point of interest,” then the following options

which allow you to specify the search area.

“---nearby GPS position”

Searches within the specified radius of the

center of the map.

“---nationwide”

Searches within the specified country.

“---in a browsed city”

Searches within the specified city.

Select on map

Searches for routes by setting the destination

directly from the map display.

“New Destination” c “Navigation” c “Select on

map”

Recent destinations

Searches for routes to recently searched

destinations.

“New Destination” c “Navigation” c “Recent

destinations”

Favorites

Searches for routes to a saved destination point.

“New Destination” c “Navigation” c

“Favorites”

16

Guidance displays

Once a route has been calculated, visual

guidance navigates you to the destination along

with audio guidance.

Information on map tool menu

1 To show/hide tool menu.

2 To switch the map direction (north up/

heading up) of the 2D map.

3 To switch to map scrolling mode.

4 To view detailed GPS information.

5 Indicates battery condition.

2D map display

Straight-ahead driving

Approaching an intersection

Approaching an intersection (closer)

Next guidance immediately after intersection

A Current position

B Distance to next turn

C Next direction

D Current street name

E Next street name

F ETA (Estimated Time of Arrival)/Distance to

destination

G Next turn instruction

H Bar indication of distance to next turn

I Instruction after next

3D map display

You can set the 3D map display in the setting

menu (page 17).

View route display

You can view the entire route to the destination.

To display, from the top menu, select “Route” c

“View route.”

1 2

3

4

5

D

A

FE

B

C

G

H

I

17

Map scrolling mode

You can switch to map scrolling mode from map

display by touching , whether during route

guidance or not.

In map scrolling mode, the cross-hair is

displayed on the map, and you can drag the

screen to scroll the map.

Touch –/+ to adjust map scale.

Place the intersection of the cross-hair on a

desired point, then touch to show the map

scrolling mode menu, where you can set the

point as a destination, etc.

Touch to return to the current car position

display.

System Settings

Various settings related to the system and

memory are configurable.

From the top menu, select “Settings,” then the

desired item below to make each setting.

For details, see the supplied PDF manual.

Volume

To adjust the voice guidance volume.

Note

When the unit is powered by the built-in battery,

maximum available volume is 70 %, even if set higher

(80 %, etc). When it is powered using the car battery

adapter or AC power adapter, this does not apply.

Select map

To select a map stored in the unit.

Map information

To show/hide the information bar (displayed at

the bottom of the map), POI icons, and street

names on the map.

Route information

To show/hide ETA (Estimated Time of Arrival)

and distance to final destination on the map.

Signpost information

To show/hide signposts indicating motorway/

highway exits*

1

on the map.

Light sensor

To adjust the sensitivity of the auto dimmer

sensor.

Graphical look

To set the brightness and map color.

Touch screen calibration

To calibrate the contact position of the touch

screen.

Auto mode

To select the default map display (2D or 3D);

automatically change the map scale depending

on the driving speed (configurable for 2D and 3D

respectively); select the default map direction for

2D map display (north up or heading up).

Routing options

To select the route search preference (time-

optimized or distance-optimized); permit/avoid

motorways, ferries and toll roads on route.

Itinerary

To automatically proceed to the next destination

after reaching the previous destination.

continue to next page t

18

*1 Displayed only if contained in the map information.

*2 This function is only for European models.

Note

Warnings given according to map information may not

always be correct due to road works, etc. Traffic

situations and road regulations take absolute

precedence over information given by the navigation

system.

Using the Supplied Software

Significant functions using the supplied software

are introduced here.

For details, see the supplied PDF manual.

Operating system requirements

• OS: Windows 98SE/2000/ME/XP

• DVD-ROM drive

•USB port

• 150 MHz CPU speed minimum

(recommended)

Connecting to your computer

1 Connect the unit to an outlet using the

AC power adapter and the AC power

cable.

2 Connect the unit to your computer

with the USB cable.

Connect the small connector of the USB

cable to the USB jack on the unit, then the

large connector to a USB port on your

computer.

Time zone

To select the time zone of the current region;

switch between daylight saving time and

standard time.

Although the current time is automatically set by

GPS, the time zone needs to be set for ETA

(Estimated Time of Arrival) to be displayed

accurately.

Format

To select 12/24-hour clock indication; select the

distance unit (kilometers/miles).

Select language

To select the desired language for on-screen

display and voice guidance.

Home address

To register your home address.

Radio muting*

2

To attenuate the radio sound.

Demo mode

To start the demonstration.

Product information

To display unit information, such as name,

version, etc., and tutorials.

19

Software features

Additional Information

Precautions

If your car has been parked in direct sunlight, allow

the unit to cool off before operating it.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the display of the

unit. Should this occur, the unit will not operate

properly. In such a case, slide the POWER switch on

the bottom right of the unit to OFF position, then

wait for about an hour until the moisture has

evaporated.

Maintenance

Fuse replacement

When replacing the fuse in the car battery adapter,

be sure to use one matching the amperage rating

stated on the original fuse. If the fuse blows, check

the power connection and replace the fuse. If the

fuse blows again after replacement, there may be an

internal malfunction. In such a case, consult your

nearest Sony dealer.

Warning

Never use a fuse with an amperage rating exceeding

the one supplied with the unit as this could damage

the unit.

Notes on unit disposal

Remove the built-in lithium-ion battery when

disposing of the unit, and return the battery to a

recycling location.

The procedure for removing the battery is explained

below.

Note

Never disassemble the unit except when disposing of

it.

Install PC connection software

PC connection software (ActiveSync) can be

installed.

Map Manager

Map data can be added to the unit from the

supplied DVD-ROM. When adding, you may

need to delete unnecessary map data from the

unit to free up memory space.

Language Manager

Language data for on-screen display and voice

guidance can be added to the unit from the

supplied DVD-ROM, and unnecessary language

data can be deleted from the unit.

Read the manual

You can read the manual in PDF format.

Support link

Easy access to the Sony navigation support site

(www.sony.com/nav-u/support) is available.

Visit this site for technical support, such as

software and firmware updates, FAQs, etc.

Re-install application

The navigation software pre-installed in the unit

can be re-installed from the supplied DVD-

ROM, in case of accidental deletion, etc.

continue to next page t

Fuse (2.5A)

To tighten

To remove

20

1 Switch off the main power by sliding

the POWER switch to the OFF

position.

2 Remove the jack cover (page 11).

3 Remove the 2 screws on the underside

of the unit using a screwdriver.

4 Slide the rear cover, then lift to open.

5 Remove the battery.

6 Insulate the connector terminal by

wrapping with a tape.

Notes on the lithium-ion battery

• Keep the battery out of the reach of children.

• Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Specifications

Main unit

Operating temperature: 5 – 45 ºC (41 – 113 ºF)

Power requirements: DC 5 V

(from supplied AC power adapter)

Connection terminals:

Cradle connector

DC IN 5V jack

USB jack

External GPS antenna jack

Speaker: 2-way speaker

Consumption current: Approx. 0.5 A

Dimensions: Approx. 104.7 × 87.5 × 42.9 mm

(4.1 × 3.5 × 1.8 in) (w × h × d)

Mass: Approx. 310 g (11 oz)

Monitor

System: Transmissive liquid crystal display

Drive system: a-Si TFT active matrix system

Dimensions: 3.5 in (4:3)

70.1 × 52.6, 87.6 mm (2.8 × 2.1, 3.5 in) (h × v, d)

Segment: 230,400 (960 × 240) dots

Cradle

Operating temperature: 5 – 45 ºC (41 – 113 ºF)

Power requirements: DC 5.2 V

(from supplied 12 V car battery adapter (negative

ground))

Connection terminals:

Unit connector

DC IN 5.2V jack

Optional accessories

External GPS Antenna: VCA-41

Car Cradle Kit: NVA-CU3

Design and specifications are subject to change

without notice.

1

2

WARNING

Battery may explode if mistreated.

Do not recharge, disassemble, or dispose of

in fire.

RECYCLING LITHIUM-ION BATTERIES

Lithium-ion batteries are recyclable.

You can help preserve our

environment by returning your used

rechargeable batteries to the collection

and recycling location nearest you.

For more information regarding recycling of

rechargeable batteries, call toll free 1-800-822-

8837, or visit http://www.rbrc.org/.

Caution: Do not handle damaged or leaking

Lithium-ion batteries.

• Lead-free solder is used for soldering.

• Halogenated flame retardants are not used in the

certain printed wiring boards.

• Use of rechargeable lithium ion batteries.

• Corrugated cardboard is used for the packaging

cushions.

• VOC (Volatile Organic Compound)-free vegetable

oil based ink is used for printing the carton.

• This manual is printed on 100 % recycled paper

using VOC (Volatile Organic Compound)-free

vegetable oil based ink.

Page is loading ...

Sony NV Series NV-U70 Quick start guide

This manual is also suitable for

Sony NV Series NV-U70 Quick start guide

in other languages

Related papers

Other documents