Turbosound TPA152/64 Quick start guide

Category
Soundbar speakers
Type
Quick start guide
TPA122/64/95/00 / TPA122/64/95/00-WH
TPA152/64/95 / TPA152/64/95-WH
TPZ122/64
TPZ152/64
TPZ153/64
Quickstart Guide
Arrayable 2-Way/3-Way 12/15" Full Range Loudspeaker for Installation Applications
2
TPA/TPZ series Quick Start Guide
3
Terminals marked with this
symbol carry electrical
current of suffi cient magnitude
to constitute risk of electric shock. Use only
high-quality commercially-available speaker
cables with plugs pre-installed. All other
installation or modifi cation should be
performed only by qualifi ed personnel.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated
dangerous voltage inside the enclosure -
voltage that may be suffi cient to constitute
a risk of shock.
This symbol, wherever it
appears, alerts you to important
operating and maintenance
instructions in the accompanying literature.
Please read the manual.
Caution
To reduce the risk of electric
shock, do not remove the
top cover (or the rear section). No user
serviceable parts inside. Refer servicing to
qualifi ed personnel.
Caution
To reduce the risk of fi re or
electric shock, do not expose
this appliance to rain and moisture.
The apparatus shall not be exposed to
dripping or splashing liquids and no objects
lled with liquids, such as vases, shall be
placed on the apparatus.
Caution
These service instructions are
for use by qualifi ed service
personnel only. To reduce the risk of
electric shock do not perform any servicing
other than that contained in the operation
instructions. Repairs have to be performed
by qualifi ed service personnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves,
or other apparatus (including amplifi ers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding-type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fi t into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11. Use only attachments/accessories
specifi ed by the manufacturer.
12. Use only with
the cart, stand,
tripod, bracket,
or table specifi ed by
the manufacturer,
or sold with
the apparatus.
When a cart is used,
use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14. Refer all servicing to qualifi ed service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
15. The apparatus shall be connected to
a MAINS socket outlet with a protective
earthing connection.
16. Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain
readily operable.
17. Correct disposal of
this product: This symbol
indicates that this product
must not be disposed of
with household waste,
according to the WEEE
Directive (2012/19/EU)
and your national law.
This product should be taken to a collection
center licensed for the recycling of waste
electrical and electronic equipment (EEE).
The mishandling of this type of waste could
have a possible negative impact on the
environment and human health due to
potentially hazardous substances that are
generally associated with EEE. At the same
time, your cooperation in the correct
disposal of this product will contribute to
the effi cient use of natural resources.
For more information about where you can
take your waste equipment for recycling,
please contact your local city offi ce, or your
household waste collection service.
LEGAL DISCLAIMER
MUSIC Group accepts no liability for
any loss which may be suffered by any
person who relies either wholly or in
part upon any description, photograph,
or statement contained herein. Technical
specifi cations, appearances and other
information are subject to change
without notice. All trademarks are the
property of their respective owners.
MIDAS, KLARK TEKNIK, TURBOSOUND,
BEHRINGER, BUGERA and DDA are
trademarks or registered trademarks of
MUSIC Group IP Ltd. © MUSIC Group IP
Ltd. 2014 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and
conditions and additional information
regarding MUSIC Group’s Limited
Warranty, please see complete details
online at music-group.com/warranty.
Important Safety
Instructions
Instrucciones de
seguridad
Las terminales marcadas con
este símbolo transportan
corriente eléctrica de magnitud
sufi ciente como para constituir un riesgo de
descarga eléctrica. Utilice solo cables de
altavoz de alta calidad con clavijas
TS de 6,3 mm pre-instaladas
(puede adquirirlos en comercios
especializados en audio). Cualquier otra
instalación o modifi cación debe ser
realizada únicamente por un
técnico cualifi cado.
Este símbolo, siempre que
aparece, le advierte de la
presencia de voltaje peligroso
sin aislar dentro de la caja; este voltaje
puede ser sufi ciente para constituir un
riesgo de descarga.
Este símbolo, siempre que
aparece, le advierte sobre
instrucciones operativas y de
mantenimiento que aparecen en la
documentación adjunta. Por favor,
lea el manual.
Atención
Para reducir el riesgo de
descarga eléctrica, no quite
la tapa (o la parte posterior). No hay
piezas en el interior del equipo que
puedan ser reparadas por el usuario.
Si es necesario, póngase en contacto con
personal cualifi cado.
Atención
Para reducir el riesgo de
incendio o descarga eléctrica,
no exponga este aparato a la lluvia,
humedad o alguna otra fuente que pueda
salpicar o derramar algún líquido sobre
el aparato. No coloque ningún tipo de
recipiente para líquidos sobre el aparato.
Atención
Las instrucciones de servicio
deben llevarlas a cabo
exclusivamente personal cualifi cado.
Para evitar el riesgo de una descarga
eléctrica, no realice reparaciones que no
se encuentren descritas en el manual de
operaciones. Las reparaciones deben
ser realizadas exclusivamente por
personal cualifi cado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atención a todas
las advertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie este aparato con un paño seco.
7. No bloquee las aberturas de
ventilación. Instale el equipo de acuerdo
con las instrucciones del fabricante.
8. No instale este equipo cerca de
fuentes de calor tales como radiadores,
acumuladores de calor, estufas u otros
aparatos (incluyendo amplifi cadores) que
puedan producir calor.
9. No elimine o deshabilite nunca la
conexión a tierra del aparato o del cable
de alimentación de corriente. Un enchufe
polarizado tiene dos polos, uno de los
cuales tiene un contacto más ancho que
el otro. Una clavija con puesta a tierra
dispone de tres contactos: dos polos y
la puesta a tierra. El contacto ancho y el
tercer contacto, respectivamente, son
los que garantizan una mayor seguridad.
Si el enchufe suministrado con el equipo
no concuerda con la toma de corriente,
consulte con un electricista para cambiar la
toma de corriente obsoleta.
10. Coloque el cable de suministro de
energía de manera que no pueda ser pisado
y que esté protegido de objetos afi lados.
Asegúrese de que el cable de suministro de
energía esté protegido, especialmente en la
zona de la clavija y en el punto donde sale
del aparato.
11. Use únicamente los dispositivos o
accesorios especifi cados por el fabricante.
12. Use únicamente
la carretilla,
plataforma, trípode,
soporte o mesa
especifi cados
por el fabricante
o suministrados
junto con el equipo.
Al transportar el
equipo, tenga cuidado para evitar daños y
caídas al tropezar con algún obstáculo.
13. Desenchufe el equipo durante
tormentas o si no va a utilizarlo durante un
periodo largo.
14. Confíe las reparaciones únicamente a
servicios técnicos cualifi cados. La unidad
requiere mantenimiento siempre que
haya sufrido algún daño, si el cable
de suministro de energía o el enchufe
presentaran daños, se hubiera derramado
un líquido o hubieran caído objetos dentro
del equipo, si el aparato hubiera estado
expuesto a la humedad o la lluvia, si ha
dejado de funcionar de manera normal o si
ha sufrido algún golpe o caída.
15. Al conectar la unidad a la toma de
corriente eléctrica asegúrese de que la
conexión disponga de una unión a tierra.
16. Si el enchufe o conector de red sirve
como único medio de desconexión,
éste debe ser accesible fácilmente.
17. Cómo debe
deshacerse de este
aparato: Este símbolo
indica que este aparato no
debe ser tratado como
basura orgánica, según lo
indicado en la Directiva
WEEE (2012/19/EU) y a las
normativas aplicables en su país. En lugar
de ello deberá llevarlo al punto limpio más
cercano para el reciclaje de sus elementos
eléctricos / electrónicos (EEE). Al hacer esto
estará ayudando a prevenir las posibles
consecuencias negativas para el medio
ambiente y la salud que podrían ser
provocadas por una gestión inadecuada de
este tipo de aparatos. Además, el reciclaje
de materiales ayudará a conservar los
recursos naturales. Para más información
acerca del reciclaje de este aparato,
póngase en contacto con el Ayuntamiento
de su ciudad o con el punto limpio local.
NEGACIÓN LEGAL
MUSIC Group no admite ningún tipo
de responsabilidad por cualquier
daño o pérdida que pudiera sufrir
cualquier persona por confi ar total
o parcialmente en la descripciones,
fotografías o afi rmaciones contenidas
en este documento. Las especifi caciones
técnicas, imágenes y otras informaciones
contenidas en este documento
están sujetas a modifi caciones sin
previo aviso. Todas las marcas
comerciales que aparecen aquí son
propiedad de sus respectivos dueños.
MIDAS, KLARK TEKNIK, TURBOSOUND,
BEHRINGER, BUGERA y DDA son marcas
comerciales o marcas registradas de
MUSIC Group IP Ltd. © MUSIC Group IP
Ltd. 2014 Reservados todos los derechos.
GARANTÍA LIMITADA
Si quiere conocer los detalles y condiciones
aplicables de la garantía así como
información adicional sobre la Garantía
limitada de MUSIC group, consulte
online toda la información en la web
music-group.com/warranty.
8
TPA/TPZ series Quick Start Guide
9
Thank you for choosing a TURBOSOUND loudspeaker product for your application. If you would like further
information about this or any other product, please visit our website at turbosound.com.
Unpacking the Loudspeaker
After unpacking the unit, please check carefully for damage. If damage is found, please notify your
supplier at once. You, the consignee, must instigate any claim. Please retain all packaging in case of future
return shipment.
System Requirements
TPA122, TPA152, TPZ122 and TPZ152 are switchable passive / bi-amp 2-way loudspeakers.
Passive operation (full range or with a subwoofer) requires 1 amplifi er channel and 1 controller channel.
The input signal is divided between the low-frequency and high-frequency drivers internally with a
passive crossover.
Bi-amp operation (full range or with a subwoofer) requires 2 amplifi er channels and 2 controller channels,
one for low frequencies and one for high frequencies. The input signal is divided between the low
frequency and high frequency driver in the controller and the individual ampli ed signals are fed to the
speaker input.
TPZ153 is a switchable bi-amp / tri-amp 3 way loudspeaker.
Bi-amp operation (full range or with a subwoofer) requires 2 amplifi er channels and 2 controller channels,
one for low frequencies and one for mid-high frequencies. The input signal is divided between the low
frequency and mid-high frequency drivers in the controller and the individual amplifi ed signals are fed
to the speaker input. The signals are then divided again between the mid and high frequency drivers
internally with a passive crossover.
Tri-amp operation (full range or with a subwoofer) requires 3 amplifi er channels and 3 controller channels,
one for low frequencies, one for mid frequencies, and a third for high frequencies. The input signal is
divided between the low frequency, mid frequency, and high frequency drivers in the controller and the
individual amplifi ed signals are fed to the speaker input.
Correct controller settings for all horn variants and operation with subwoofers can be downloaded from
the website, and are also available as presents for the LMS series controllers.
To avoid wasting ampli er power, you should use heavy-duty speaker cable with a minimum wire size of
1.5 mm
2
(16 AWG), and preferably 2.5 mm
2
(14 AWG) for longer runs. For extreme cable lengths, be aware
of cable impedance and resistive losses. Always observe the correct polarity.
᧙᜷߸Мᮍ
ࣝధ൦ಗ঄ᄋጽቬ᝻ܭЧధृ
ܹᄋႄุߜڛᝐႄԁᬘǎ̪ᬎ
Ώၺࣝధ ¼" TSੌ੶ᩛऱତ݁
ᄋᰵַ᠐˅ˋੵܧ٩ጴǎ੟ధᄋ߸ᜊੌ
஠ڪᮍՍಬ˅ˋ̢ցᤊᛢǎ
൦ಗ঄ଣᧉ১ַ̘аߜڛ
ፑᎇᄋԁᬘႄԎధᝐႄԁᬘǎ
൦ಗ঄ଣᧉ১ಋ੟ᬅ᧙᜷
ᄋΏၺԤ፦οឮ௛ǎឱ᫟឵
У੥гǎ
࠶ॸ
˟ᥙГᝐႄԁᬘឱӉ੫ऩ
ᮈᄧੌᑁ᭨૖ౝǎ᝻ܭа෦
ధԼΚၺਜ਼፦οΏၺᄋᦋ͉ǎឱ࠳፦ο̄
ᮋ̕ႁՍಬᄋ˅ˋ̢ցᤊᛢǎ
࠶ॸ
˟ᥙГ༣ੌᝐႄԁᬘឱӉ
࠳൦᝻ܭ̇ᭂ๹ੌ˘ǎ
᝻ܭ˸ˁԼԫ๰͵๰͵
٩˸ˁԼᎷ̇Цʾݡᔊၬ኏ǎ
࠶ॸ
፦οឮ௛̪௨ፍՍಬᄋ˅ˋ
ο̢ցΏǎ˟Гԁ
ᬘᬕ́Ώၺឮ௛˻ଣ҃ᄋ̀ܲឱӉᤊᛢ
͋ͶЦ߳፦οǎ੟ధ፦οڪᮍႁՍಬᄋ˅
ˋ̢ցᤊᛢǎ
1. ឱ᫟឵ᤉ̐ឮ௛ǎ
2. ឱݱؔεߜᤉ̐ឮ௛ǎ
3. ឱญਔ੟ధᄋ᝞ᇩǎ
4. ឱᥗ߷੟ధᄋឮ௛ǎ
5. ឱӉڛ᭦ᤄබᄋڢஶΏၺశַ̘ǎ
6. ឱၺࣱ࣌ຎพశַ̘ǎ
7. ឱӉ܅܌ᤱ᮴Աǎ߸ᜊశַ̘௒ឱᥗ
ཱིԉࠓᄋឮ௛ǎ
8. ឱӉ࠳శַ̘߸ᜊڛམ຺ᬅᤄ
ݡ఍ජྠ༰ߖੌЦ̘߳ၸམ᧛ᄋ᝻ܭ
Ӌ઻ҫ஋٩ǎ
9. ឱӉሩᬕ౞মତ݁ੌ଍ڢତ݁ᄋ߸М
ᜊᎷǎ଍ڢତ݁௨ႁˑ˕ତ܌଍གྷԤʸ˕
଍ڢ݁౟ੈǎᔫᬥ᠏ଣΚᄋତ݁ˁᤡՍ১
ᄋତऑឱ੾ႄࢻట૲ʸ˕Սᤡᄋତऑǎ
10. ݱؔεઑႄ຺ጴΏЦˁᜃ᡼ᢇੌ҉
ᆢࡀЦญਔႄ຺ତ݁Ǎܴၺ᤮ତऑԤ᝻ܭ
ᤍ଍ܬǎ
11. ឱԷΏၺԉࠓ૊ࠁᄋᬅ࡜᝻ܭ֘ᦢ͉ǎ
12. ឱԷΏၺԉࠓ
૊ࠁᄋੌᬥ᠏ᩚ
׭ᄋ੥ଏᢽ౷ߖ
ʽᝉ౷஄౷֘ಹ
ߖǎᔫΏၺ੥ଏᢽ
౐ୄᤃ᝻ܭឱญ
ਔ߸М஋Ꮇ᝻ܭ
̀ᥙГ੥ଏᢽ֘᝻
ܭϛωᏬԫ͟ǎ
13. ᥆᫆ႄᭈᲟੌ᫃ఱˁΏၺశ᝻ܭ௒
ឱફѤႄ຺ତ݁ǎ
14. ੟ధ፦οڪᮍႁՍಬᄋ፦ο̢ցᤊ
ᛢǎ᝻ܭԫ૰௒ᭋᤊᛢ፦οΔݡႄ຺ጴੌ
ႄ຺ତ݁ԫ૰๰͵ุЛੌफྮᗁЛ᝻ܭ
а᝻ܭᥔᭂ๹ੌԫ໾᝻ܭˁᑠ൥ࣣᤃͼ
ੌᜃ୒گǎ
15. శ᝻ܭᤍ଍ႄ຺௒ʸࠁ᜷ధ଍ڢ
εઑǎ
16. ᔫႄ຺ତ݁ੌ٩Ч
ᏺՍ٩ၺͼளႄᜊᎷ
अैε᝾߳̈́ܬ̇ᬥ௒Լ
ஶΨ୳ͼ࿅ঘǎ
17. శַ̘̪ᤡၺ̇๓ફ
2000ዜ̀ʿڢӞశַ̘
̪ᤡၺ̇᭥མࣝජό౏
͉ʿǎ
ฃ०ܧ௛
ࠬ̇͋Ͷڃڛ൦ឮ௛˻ଣ҃ᄋМᦋ
ੌᦋ͌ଢᤙǍڐྠੌܧ௛Ꮼᤶੈᄋ૰
݀MUSIC Groupˁ᠈͋Ͷ᠋͋ǎ
઀సԡஞ֘ܲ᜻ᔫధటஉিˁԴᛢ
ᤱᅽǎ੟ధᄋ׹ಗڪ˟ЦՋᒮ੟ధᏩ
ᄋ᠊̘ǎMIDASKLARK TEKNIK
TURBOSOUNDBEHRINGERBUGERA
֘DDA௨MUSIC Group IP Ltd.ОՄᄋ
׹ಗੌญг׹ಗǎ© MUSIC Group IP
Ltd. 2014ྡీ੟ధǎ
εο౏൝
ధУᮄˮᬸڅεοᄋᤡၺ౏
൝ԤЦ߳ᄲУθ্ឱᄇᬇ
music-group.com/warranty
Ꭻቤಋᄻߺ஠ᄋឡጻθ্ǎ
10
TPA/TPZ series Quick Start Guide
11
Amplifi er Considerations
The TPA and TPZ series loudspeakers are optimized for use with the TURBOSOUND T series amplifi ers with
the LMS series controllers. A full range of DSP settings to suit any con guration are provided for download
on the TURBOSOUND website. The use of third party amplifi cation and processing is only advised using the
matrix of manual settings as well as the limiter calculator provided on the TURBOSOUND website. The TPA
and TPZ series loudspeaker enclosures should be driven by high quality power amplifi ers designed for true
professional use. Power amplifi ers should be capable of delivering long term broadband power equal to half
the loudspeakers peak power rating at its stated nominal impedance. The use of underpowered amplifi ers
must be avoided as heavily clipped signals can cause permanent loudspeaker damage. Limiters, crossovers
and equalisation points must be set in accordance with the settings provided on the TURBOSOUND website.
This will ensure the optimum sound quality and long-term reliability as well as protection from damage.
Neutrik speakON* NL4 locking input connector(s) and 4-way barrier strip(s) are provided, allowing options
for input and link, passive, bi-amp and tri-amp operation.
Model TPA122 TPA152 TPZ122 TPZ152
Mode Passive Bi-amp LF Bi-amp HF Passive Bi-amp LF Bi-amp HF Passive Bi-amp LF Bi-amp HF Passive Bi-amp LF Bi-amp HF
Impedance 8 Ω 8 Ω 6 Ω 8 Ω 8 Ω 6 Ω 8 Ω 8 Ω 6 Ω 8 Ω 8 Ω 6 Ω
Minimum
Amplifi er
Power
Continuous
RMS
500 W 500 W 40 W 500 W 500 W 40 W 600 W 600 W 75 W 650 W 650 W 75 W
Peak 2000 W 2000 W 400 W 2000 W 2000 W 400 W 2400 W 2400 W 750 W 2600 W 2600 W 750 W
Model TPZ153
Mode Bi-amp LF Bi-amp MF/HF Tri-amp LF Tri-amp MF Tri-amp HF
Impedance 8 Ω 8 Ω 8 Ω 8 Ω 6 Ω
Minimum
Amplifi er
Power
Continuous
RMS
650 W 200 W 650 W 200 W 75 W
Peak 2600 W 800 W 2600 W 800 W 750 W
Passive
Bi-Amp
HPF
HF
NL4
Input/
Link
1+
1 -
2+
2 -
>
>
>
>
>
>
>
>
1+
1 -
2+
2 -
Barrier
Strip
Input/
Link
LPF
LF
HF
NL4
Input/
Link
1+
1 -
2+
2 -
>
>
>
>
>
>
>
>
1+
1 -
2+
2 -
Barrier
Strip
Input/
Link
LF
speakON* NL4
Barrier Strip
1-
2-
2+
1+
PASSIVE, Input Full Range -
PASSIVE, Input Full Range -
PASSIVE, Input Full Range +
PASSIVE, Input Full Range +
1+ 1- 2+ 2-
speakON* NL4
Barrier Strip
1+ 1- 2+ 2-
BI-AMP, Input Low +
BI-AMP, Input Low +
BI-AMP, Input Low -
BI-AMP, Input Low -
BI-AMP, Input High +
BI-AMP, Input High +
BI-AMP, Input High -
BI-AMP, Input High -
1-
2-
2+
1+
Amplifier Channel 1
Amplifier Channel 2
Mode Back Panel Connector Internal Schematic
Connections
Models: TPA122, TPA152, TPZ122, TPZ152
Tri-Amp
speakON* NL4
Barrier Strip
1-
2-
2+
1+
BI-AMP, Input Low -
BI-AMP, Input Low -
BI-AMP, Input Mid-High +
BI-AMP, Input Mid-High -
BI-AMP, Input Mid-High +
BI-AMP, Input Mid-High -
BI-AMP, Input Low +
BI-AMP, Input Low +
1-
2-
2+
1+
1+
1-
2+
2-
3+
3-
4+
4-
Bi-Amp
Amplifier Channel 1
INPUT 1/2
INPUT 3/4
Amplifier Channel 2
speakON* NL4
Barrier Strip
1-
2-
2+
1+
TRI-AMP, Input Low -
TRI-AMP, Input Low -
TRI-AMP, Input Mid +
TRI-AMP, Input Mid -
TRI-AMP, Input Mid +
TRI-AMP, Input Mid -
TRI-AMP, Input Low +
TRI-AMP, Input Low +
1-
2-
2+
1+
1+
1-
2+
2-
3+
3-
4+
4-
Amplifier Channel 1
INPUT 1/2
INPUT 3/4
TRI-AMP, Input High -
TRI-AMP, Input High +
Amplifier Channel 3
Amplifier Channel 2
TRI-AMP, Input High -
TRI-AMP, Input High +
Mode Back Panel Connector Internal Schematic
Model TPZ153
12
TPA/TPZ series Quick Start Guide
13
Suspending with Eyebolts
TPA and TPZ cabinets can be suspended using optional eyebolts coupled
to the internal rigging points provided on the top, bottom and sides and
back. The simplest method is to use the two rigging points on the top and
a single pull-back rigging point in the centre of the rear panel.
Remove the appropriate countersunk screws and replace them with
shoulder eyebolts, which must have a thread length of at least 18 mm.
Use the rear rigging point to angle the cabinet for optimum room
coverage. Cabinets may be hung upside down if required.
IMPORTANT NOTE: The mounting of a permanently installed sound system
may be dangerous unless undertaken by qualifi ed personnel with the
required experience and certi cation to perform the necessary tasks. Walls, fl oors or ceilings must be
capable of safely and securely supporting the actual load. The mounting accessory used must be safely
and securely fi xed both to the loudspeaker and to the wall, fl oor or ceiling.
When mounting rigging components on walls, fl oors or ceilings, ensure that all fi xings and fasteners
used are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and
composition of walls and ceilings, all need to be taken into account when determining whether a
particular fi xing arrangement can be safely employed for a particular load. Cavity plugs or other specialist
xings, if required, must be of an appropriate type, and must be fi tted and used in accordance with the
maker’s instructions.
The operation of your speaker cabinet as part of a fl own system, if installed incorrectly and improperly,
can potentially expose persons to serious health risks and even death. In addition, please ensure that
electrical, mechanical and acoustic considerations are discussed with quali ed and certi ed (by local state
or national authorities) personnel prior to any installation or fl ying.
Make sure that speaker cabinets are set up and fl own by qualifi ed and certifi ed personnel only,
using dedicated equipment and original parts and components delivered with the unit. If any parts or
components are missing please contact your dealer before attempting to set up the system.
Be sure to observe the local, state and other safety regulations applicable in your country. MUSIC Group,
including the MUSIC Group companies listed on the enclosed “Service Information Sheet, assumes no
liability for any damage or personal injury resulting from improper use, installation or operation of the
product. Regular checks must be conducted by qualifi ed personnel to ensure that the system remains in a
secure and stable condition. Make sure that, where the speaker is fl own, the area underneath the speaker is
free of human traf c. Do not fl y the speaker in areas that can be entered or used by members of the public.
Speakers create a magnetic fi eld, even if not in operation. Therefore, please keep all materials that can
be affected by such fi elds (discs, computers, monitors, etc) at a safe distance. A safe distance is usually
between 1 and 2 metres.
Mounting and Fixing
TPA and TPZ series cabinets are designed with multiple internal rigging points to suit many possible
mounting methods in permanent installations. The graphic below shows the assembly of the optional
mounting bracket (TPA122-WB and TPA152-WB).
ITEM QTY COMPONENT
1 2 M10 x 45 screw
22Flat washer
3 2 Friction washer
4 2 Rotate lock screw
52Spring washer
61Wall bracket
Wall Brackets
1. Remove the M10 blanking bolts from the speaker.
The bracket will be mounted to these points.
2. Install the wall plate in the venue using the appropriate
xings (not supplied).
3. Lift the speaker to the bracket and attach with the
supplied M10 bolts and friction washers.
4. Set the desired speaker angle and insert the 2
locking screws.
5. For added precaution and where required by local
standards, install an M10 threaded eyebolt in the back of
the speaker, then connect a properly-rated safety cable from the eyebolt to the mounting structure.
The TPZ153-FK fl y kit is also available for suspension of 3 TPZ153 models. Array angles from 50 degrees
to 90 degrees can be chosen in 5 degree increments. The fl y kit comprises an upper and lower fl y plate,
4 eyebolts and M10 fi xings required for installation. See turbosound.com for more information.
1
2
3
4
5
6
14
TPA/TPZ series Quick Start Guide
15
Technical Specifi cations
TPA152/64 (WH) TPA152/95 (WH) TPA122/64 (WH) TPA122/95 (WH) TPA122/00 (WH) TPZ153/64 TPZ152/64 TPZ122/64
System
Frequency response
43 Hz – 18 kHz ±3 dB
37 Hz – 20 kHz -10 dB
43 Hz – 18 kHz ±3 dB
37 Hz – 20 kHz -10 dB
45 Hz – 18 kHz ±3 dB
40 Hz – 20 kHz -10 dB
45 Hz – 18 kHz ±3 dB
40 Hz – 20 kHz -10 dB
45 Hz – 18 kHz ±3 dB
40 Hz – 20 kHz -10 dB
45 Hz – 20 kHz ±3 dB
38 Hz – 20 kHz -10 dB
41 Hz – 18 kHz ±3 dB
35 Hz – 20 kHz -10 dB
43 Hz – 18 kHz ±3 dB
37 Hz – 20 kHz -10 dB
Nominal dispersion
60° H x 40° V @ -6 dB points,
rotatable
90° H X 50° V @ -6 dB points,
rotatable
60° H X 40° V @ -6 dB points,
rotatable
90° H X 50° V @ -6 dB points,
rotatable
100° H X 100° V @ -6 dB points,
rotatable
60° H x 40° V @ -6 dB points,
rotatable
60° H X 40° V @ -6 dB points,
rotatable
60° H X 40° V @ -6 dB points,
rotatable
Directivity factor (Q)
18.3 10.4 18.3 10.4 5 18.3 18.3 18.3
Directivity index (DI)
12.6 10.2 12.6 10.2 7 12.6 12.6 12.6
Power handling (IEC)
Passive
500 W continuous,
2,000 W peak
500 W continuous,
2,000 W peak
500 W continuous,
2,000 W peak
500 W continuous,
2,000 W peak
500 W continuous, 2,000 W peak 650 W continuous, 2,600 W peak 600 W continuous, 2,400 W peak
Bi-amp
LF: 500 W continuous,
2,000 W peak
HF: 40 W continuous,
160 W peak
LF: 500 W continuous,
2,000 W peak
HF: 40 W continuous,
160 W peak
LF: 500 W continuous,
2,000 W peak
HF: 40 W continuous,
160 W peak
LF: 500 W continuous,
2,000 W peak
HF: 40 W continuous,
160 W peak
LF: 500 W continuous, 2,000 W peak
HF: 40 W continuous, 160 W peak
LF: 650 W continuous,
2,600 W peak
M/HF: 200 W continuous,
800 W peak
LF: 650 W continuous, 2,600 W peak
HF: 75 W continuous, 300 W peak
LF: 600 W continuous, 2,400 W peak
HF: 75 W continuous, 300 W peak
Tri-amp ————
LF: 650 W continuous, 2,600 W peak
MF: 200 W continuous, 800W peak
HF: 75 W continuous, 300 W peak
——
Sensitivity
97 dB (1 W @ 1 m) 97 dB (1 W @ 1 m) 97 dB (1 W @ 1 m) 97 dB (1 W @ 1 m) 97 dB (1 W @ 1 m)
LF: 97 dB (1 W @ 1 m)
MF: 107 dB (1 W @ 1 m)
HF: 109 dB (1 W @ 1 m)
97 dB (1 W @ 1 m) 96 dB (1 W @ 1 m)
Maximum SPL
Passive
124 dB continuous, 130 dB
peak
124 dB continuous, 130 dB
peak
124 dB continuous, 130 dB
peak
124 dB continuous, 130 dB
peak
124 dB continuous, 130 dB peak 125 dB continuous, 131 dB peak 124 dB continuous, 130 dB peak
Bi-amp
LF: 124 dB continuous, 130
dB peak
HF: 122 dB continuous, 128
dB peak
LF: 124 dB continuous, 130
dB peak
HF: 122 dB continuous, 128
dB peak
LF: 124 dB continuous, 130
dB peak
HF: 122 dB continuous, 128
dB peak
LF: 124 dB continuous, 130
dB peak
HF: 122 dB continuous, 128
dB peak
LF: 124 dB continuous, 130 dB peak
HF: 122 dB continuous, 128 dB peak
LF: 125 dB continuous, 131 dB peak
MHF: 128 dB continuous,
134 dB peak
LF: 125 dB continuous, 131 dB peak
HF: 128 dB continuous, 134 dB peak
LF: 124 dB continuous, 130 dB peak
HF: 128 dB continuous, 134 dB peak
Tri-amp ————
LF: 125 dB continuous, 131 dB peak
MF: 130 dB continuous, 136 dB peak
HF: 128 dB continuous, 134 dB peak
——
Impedance
Passive 8 Ω
LF: 8 Ω
HF: 6 Ω
8 Ω
LF: 8 Ω
HF: 6 Ω
8 Ω
LF: 8 Ω
HF: 6 Ω
8 Ω
LF: 8 Ω
HF: 6 Ω
8 Ω
LF: 8 Ω
HF: 6 Ω
LF: 8 Ω
MHF: 8 Ω
8 Ω
LF: 8 Ω
HF: 6 Ω
8 Ω
LF: 8 Ω
HF: 6 Ω
Bi-amp
Tri-amp ————
LF: 8 Ω
MF: 8 Ω
HF: 6 Ω
——
Crossover type
Passive / Bi-amp, switchable Passive / Bi-amp, switchable Passive / Bi-amp, switchable Passive / Bi-amp, switchable Passive / Bi-amp, switchable Bi-amp / tri-amp switchable Passive / Bi-amp, switchable Passive / Bi-amp, switchable
Components
1 x 15" (394 mm) LF driver
1 x 1" (25 mm)
HF compression driver
1 x 15" (394 mm) LF driver
1 x 1" (25 mm)
HF compression driver
1 x 12" (316 mm) LF driver
1 x 1" (25 mm)
HF compression driver
1 x 12" (316 mm) LF driver
1 x 1" (25 mm)
HF compression driver
1 x 12" (316 mm) LF driver
1 x 1" (25 mm)
HF compression driver
1 x 15" (394 mm) LF driver
1 x 8" (200 mm) MF driver
1 x 1.4" (36 mm)
HF compression driver
1 x 15" (394 mm) LF driver
1 x 1.4" (36 mm)
HF compression driver
1 x 12" (316 mm) LF driver
1 x 1.4" (36 mm)
HF compression driver
Enclosure
Connectors
1 x Neutrik speakON* NL4,
1 x barrier strip terminals
1 x Neutrik speakON* NL4,
1 x barrier strip terminals
1 x Neutrik speakON* NL4,
1 x barrier strip terminals
1 x Neutrik speakON* NL4,
1 x barrier strip terminals
1 x Neutrik speakON* NL4,
1 x barrier strip terminals
2 x Neutrik speakON* NL4,
2 x barrier strip terminals
1 x Neutrik speakON* NL4,
1 x barrier strip terminals
1 x Neutrik speakON* NL4,
1 x barrier strip terminals
Wiring
Passive
Pins 1+ / 1- input,
pins 2+ / 2- link
Pins 1+ / 1- input,
pins 2+ / 2- link
Pins 1+ / 1- input,
pins 2+ / 2- link
Pins 1+ / 1- input,
pins 2+ / 2- link
Pins 1+ / 1- input, pins 2+ / 2- link Pins 1+ / 1- input, pins 2+ / 2- link Pins 1+ / 1- input, pins 2+ / 2- link
Bi-amp Pins 1+ / 1- LF, pins 2+ / 2- HF Pins 1+ / 1- LF, pins 2+ / 2- HF Pins 1+ / 1- LF, pins 2+ / 2- HF Pins 1+ / 1- LF, pins 2+ / 2- HF Pins 1+ / 1- LF, pins 2+ / 2- HF
Pins 1+ / 1- LF, pins 2+ / 2- MHF,
pins 3+ / 3- and pins 4+ / 4- link
Pins 1+ / 1- LF, pins 2+ / 2- HF Pins 1+ / 1- LF, pins 2+ / 2- HF
Tri-amp ————
Pins 1+ / 1- LF, pins 2+ / 2- MF,
pins 3+ / 3- HF, pins 4+ / 4- Link
——
Dimensions (HWD)
781 x 419 x 503 mm
(30.7 x 16.5 x 19.8")
781 x 419 x 503 mm
(30.7 x 16.5 x 19.8")
711 x 368 x 458 mm
(28.0 x 14.5 x 18.0")
711 x 368 x 458 mm
(28.0 x 14.5 x 18.0")
711 x 368 x 458 mm
(28.0 x 14.5 x 18.0")
967 x 559 x 656 mm
(38.0 x 22.0 x 25.8")
781 x 419 x 503 mm
(30.7 x 16.5 x 19.8")
711 x 368 x 458 mm
(28.0 x 14.5 x 18.0")
Net weight
26.8 kg (59 lbs) 27.0 kg (59.4 lbs) 23.8 kg (52.4 lbs) 23.3 kg (51.3 lbs) 23.2 kg (51.1 lbs) 43.3 kg (95 lbs) 26.8 kg (59.0 lbs) 23.4 kg (51.5 lbs)
Construction
15 mm (
5
/
8
") birch plywood 15 mm (
5
/
8
") birch plywood 15 mm (
5
/
8
") birch plywood 15 mm (
5
/
8
") birch plywood 15 mm (
5
/
8
") birch plywood 15 mm (
5
/
8
") birch plywood 15 mm (
5
/
8
") birch plywood 15 mm (
5
/
8
") birch plywood
Finish
Semi-matt black paint
(white optional)
Semi-matt black paint
(white optional)
Semi-matt black paint
(white optional)
Semi-matt black paint
(white optional)
Semi-matt black paint
(white optional)
Semi-matt black paint Semi-matt black paint Semi-matt black paint
Grille
Powder-coated
perforated steel
Powder-coated
perforated steel
Powder-coated
perforated steel
Powder-coated
perforated steel
Powder-coated perforated steel Powder-coated perforated steel Powder-coated perforated steel Powder-coated perforated steel
Flying hardware
M10 x 15 points M10 x 15 points M10 x 15 points M10 x 15 points M10 x 15 points M10 x 13 points M10 x 15 points M10 x 15 points
Accessories
TPA152-WB wall bracket
PRAGUE 15"
TPA152-WB wall bracket
PRAGUE 15"
TPA122-WB wall bracket
PRAGUE 12"
TPA122-WB wall bracket
PRAGUE 12"
TPA122-WB wall bracket
PRAGUE 12"
TPZ153-FK
TPA152-WB wall bracket
PRAGUE 15"
TPA122-WB wall bracket
PRAGUE 12"
16
TPA/TPZ series Quick Start Guide
17
Other important information
1. Register online. Please register your
new MUSIC Group equipment right after
you purchase it by visiting turbosound. com.
Registering your purchase using our
simple online form helps us to process your
repair claims more quickly and effi ciently.
Also, read the terms and conditions of our
warranty, if applicable.
2. Malfunction. Should your MUSIC Group
Authorized Reseller not be located in your
vicinity, you may contact the MUSIC Group
Authorized Fulfi ller for your country listed
under “Support” at turbosound. com.
Should your country not be listed, please
check if your problem can be dealt with by
our “Online Support” which may also be
found under “Support” at turbosound. com.
Alternatively, please submit an online warranty
claim at turbosound. com BEFORE returning
the product.
3. Power Connections. Before plugging
the unit into a power socket, please make
sure you are using the correct mains voltage
for your particular model. Faulty fuses must
be replaced with fuses of the same type and
rating without exception.
Important information
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Turbosound TPA152/64 Quick start guide

Category
Soundbar speakers
Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI