FORS WE9567 User manual

WE9567

User Manual

Washing

Machine

Benutzerin‐

formation

Waschma‐

schine

CONTENTS

Safety information 2

Safety instructions 3

Product description 5

Control panel 6

Programmes 9

Consumption values 14

Options 15

Settings 16

Before first use 17

Daily use 17

Hints and tips 21

Care and cleaning 22

Troubleshooting 26

Emergency door opening 28

Technical Data 29

Guarantee Conditions 29

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damages that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Do not let children play with the appliance.

• Children aged 3 years and under must be kept away from

this appliance when it is in operation at all times.

• Keep all packaging away from children and dispose of it

appropriately.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the

door is open.

• If the appliance has a child safety device, this should be

activated.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

2

General Safety

• Do not change the specification of this appliance.

• Do not exceed the maximum load of 9 kg (refer to the

"Programme chart" chapter).

• The operating water pressure at the water entry point from

the outlet connection must be between 0.5 bar (0.05 MPa)

and 8 bar (0.8 MPa).

• The ventilation opening in the base must not be covered

by a carpet, mat, or any floor covering.

• The appliance must be connected to the water mains using

the new supplied hose sets, or other new hose sets

supplied by the Authorised Service Centre.

• Old hose sets must not be reused.

• If the mains power supply cable is damaged, it must be

replaced by the manufacturer, its Authorised Service

Centre or similarly qualified persons to avoid an electrical

hazard.

• Before any maintenance operation, deactivate the

appliance and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to

clean the appliance.

• Clean the appliance with a moist cloth. Use only neutral

detergents. Do not use abrasive products, abrasive

cleaning pads, solvents or metal objects.

SAFETY INSTRUCTIONS

Installation

• Remove all the packaging and the

transit bolts.

• Keep the transit bolts in a safe place. If

the appliance is to be moved in future

they must be reattached to lock the

drum to prevent internal damage.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Do not install or use a damaged

appliance.

• Follow the installation instruction

supplied with the appliance.

• Do not install or use the appliance

where the temperature can be less

than 0°C or where it is exposed to the

weather.

• The floor area where the appliance is to

be installed must be flat, stable, heat

resistant and clean.

• Make sure that there is air circulation

between the appliance and the floor.

• Do not install the appliance directly

over the floor drain.

• Adjust the feet to have the necessary

space between the appliance and the

flooring.

3

• Do not install the appliance where the

appliance door cannot be fully opened.

• Do not put a container to collect

possible water leakage under the

appliance. Contact the Authorised

Service Centre to ensure which

accessories can be used.

Electrical connection

• The appliance must be earthed.

• Always use a correctly installed

shockproof socket.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by

our Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• Do not touch the mains cable or the

mains plug with wet hands.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• This appliance complies with the E.E.C.

Directives.

Water connection

• Do not cause damage to the water

hoses.

• Before connection to new pipes, pipes

not used for a long time, where repair

work has been carried out or new

devices fitted (water meters, etc.), let

the water flow until it is clean and clear.

• Ensure that there are no visible water

leaks during and after the first use of

the appliance.

• Do not use an extension hose if the

inlet hose is too short. Contact the

service centre for the replacement of

the inlet hose.

• You can extend the drain hose to

maximum 400 cm. Contact the service

centre for the other drain hose and the

extension.

Use

WARNING! Risk of injury,

electrical shock, fire, burns or

damage to the appliance.

• This appliance is for household use

only.

• Follow the safety instructions on the

detergent packaging.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

• Make sure that all metal objects are

removed from the laundry.

• Do not wash fabrics which are heavily

soiled with oil, grease or other greasy

substances. It can damage rubber

parts of the washing machine. Prewash

such fabrics by hand before loading

them into the washing machine.

• Do not touch the glass door while a

programme is in operation. The glass

can get hot.

Service

• To repair the appliance contact an

Authorised Service Centre.

• Use original spare parts only.

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains electrical and water supplies.

• Cut off the mains electrical cable close

to the appliance and dispose of it.

• Remove the door catch to prevent

children or pets from becoming trapped

in the drum.

• Dispose of the appliance in accordance

with local requirements for the disposal

4

of Waste Electrical and Electronic

Equipment (WEEE).

PRODUCT DESCRIPTION

Appliance overview

1

2

3

5

6

7

4

1

Worktop

2

Detergent dispenser

3

Control panel

4

Door handle

5

Rating plate

6

Drain pump filter

7

Feet for levelling the appliance

How to activate the child safety

device

This device prevents children or pets from

being closed in the drum.

Turn the device clockwise, until the groove

is horizontal.

You cannot close the door.

To close the door, turn the device

anticlockwise until the groove is vertical.

Fixing plate kit (4055171146)

Available from your authorised dealer.

If you install the appliance on a plinth,

secure the appliance in the fixing plates.

Read carefully the instructions supplied

with the accessory.

5

CONTROL PANEL

Control panel description

1

On/Off button (Auto Off)

2

Programme knob

3

Display

4

Start/Pause button (Start/Pause -

Départ/Pause)

5

Delay Start button (Zeitvorwahl -

Départ Différé )

6

Time Save button (Zeit Sparen - Gain

de Temps)

7

Extra Rinse button (Extra Spülen -

Rinçage +)

8

Stains/Prewash button (Flecken -

Taches / Vorwäsche - Prélavage)

9

Spin reduction button (U./Min. - T/min.)

10

Temperature button (Temperatur -

Température)

Display

A H

JKL

C D E F GB

I

6

The display shows:

A

Temperature of the set programme

Cold water

B

Spin speed of the set programme

No Spin symbol

1)

Rinse hold symbol

1)

Only available for SPIN/DRAIN programme.

C

The phase symbols

When a programme is set, all the symbols of the phases related to the programme

come on.

When the programme starts, only the symbol of the phase in operation flashes.

When the programme is completed, the symbol of the last phase is on.

Prewash phase

Washing phase

Rinse phase

Spin phase

D

The steam symbol comes on when you set a Steam programme (if

available in your appliance).

E

The detergent overdosing symbol comes on at the end of the cycle

when the appliance detects too much detergent.

F

You cannot open the appliance door when the symbol is on. You can

open the door only when the symbol goes off.

If the programme is completed but the symbol stays on:

• The «Rinse hold» function is on.

• There is water in the drum.

G

The delay start symbol comes on when you set the delay start function.

7

H

Programme time

When the programme starts, the programme time decreases with steps

of 1 minute.

Delay start

When you press the delay start button, the display shows the delay start

time

Alarm codes

If the appliance has a malfunction, the display shows alarm codes. Re‐

fer to «Troubleshooting».

The display shows this message for some seconds when:

• you cannot set a function with the washing programme

• you try to change the washing programme while it operates.

When the programme is completed.

I

The child safety lock symbol comes on when this device is activated.

Graphic bars

The empty indicator bar appears only if the related function is available

for the set programme.

The indicator bar fills accordingly to the set functions.

If you make a wrong selection the message Err indicates that the selec‐

tion is not possible.

J

The time save symbol comes on when you set one of the programme

duration.

Shortened time

Extra Quick

K

The extra rinse symbol comes on when this function is activated.

The value shows the total number of the rinses.

The indicator bar is fully filled when you set the maximum number of rin‐

ses.

8

L

the Stain symbol comes on when you activate the function.

The Prewash symbol comes on when this function is activated.

The indicator bar is not fully filled when you set only one of the func‐

tions.

The indicator bar is fully filled when you set the two functions.

PROGRAMMES

Programme Chart

Programme

Temperature range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Washing programmes

Koch/Bunt - Blanc/Couleurs

95°C - Cold

9 kg

1600 rpm

White cotton and coloured cotton.

Normal soil and light soil.

Extra Leise - Extra Silence

95°C - Cold

9 kg White and coloured cotton. Normal soil

and light soil. The programme eliminates

all spinning phase to perform a silent cy‐

cle. The cycle stops with water in the

tub.

Pflegeleicht - Synthétiques

60° C- Cold

4 kg

1200 rpm

Synthetic items or mixed fabric items.

Normal soil.

Leichtbügeln - Repassage

Facile

60° C - Cold

4 kg

800 rpm

Synthetic items requiring a gentle

wash. Normal and light soil.

1)

Feinwäsche - Délicats

40° C - Cold

4 kg

1200 rpm

Delicate fabrics such as acrylics, vis‐

cose and mixed fabrics requiring a

mild washing. Normal soil.

Wolle/Seide - Laine/Soie

40° C - Cold

2 kg

1200 rpm

Machine washable wool, hand washa‐

ble wool and other fabrics with «hand

washing» care symbol

2)

.

Daunen - Couette

60°C - 30° C

3 kg

800 rpm

Special programme for one synthetic

blanket, duvet, bedspread and so on.

9

Programme

Temperature range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Anti-Allergie - Anti-Allergies

60° C

9 kg

1600 rpm

White cotton items. This programme

removes micro-organisms thanks to the

washing by 60°C and adds one rinse. In

this way the wash is more effective.

Schleudern/Pumpen - Essor‐

age/Vidange

9 kg

1600 rpm

To spin the laundry and to drain the wa‐

ter in the drum. All fabrics, except

woollens and delicate fabrics.

Spülen - Rinçage

Cold

9 kg

1600 rpm

To rinse and spin the laundry. All fab‐

rics, except woollens and very delicate

fabrics. Reduce the spin speed accord‐

ingly to the type of laundry.

Jeans

60° - Cold

9 kg

1200 rpm

Items in denim and jersey. Also for

dark coloured items.

20 min.-3 kg

40°C - 30°C

3 kg

1200 rpm

Cotton and synthetic items with light

soil level or worn only once.

Super Eco 30°

30°C - Cold

3 kg

1200 rpm

Cottons, synthetic and mixed fabrics.

Normal soil

3)

.

Baumwolle Eco - Coton Eco

4)

60°C - 40° C

9 kg

1600 rpm

White cotton and fast-coloured cot‐

ton. Normal soil. The energy consump‐

tion decreases and the time of the wash‐

ing programme is extended.

Steam programmes

5)

Steam can be used for dried, washed or worn once laundry. These programmes

can reduce creases and odours and make your laundry softer.

Do not use any detergent. If necessary, remove stains by washing or using local‐

ized stain removal.

Steam programmes do not perform any hygienic cycle.

Do not set a Steam programme with these types of items:

• Items to be washed at a temperature lower than 40°C.

• Items where it is not specified on the care label as being suitable for tumble drying.

• All items with plastic, metal, wooden parts or alike.

10

Programme

Temperature range

Maximum

load

Maximum

spin speed

Programme description

(Type of load and soil level)

Auffrischen - Rafraîchir

1.5 kg Steam programme for cotton and syn‐

thetic items. This cycle removes odours

from the laundry

6)

.

Glätten - Défroissage

1.5 kg Steam programme for synthetic items.

This cycle helps to dewrinkle the laun‐

dry.

1)

To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin phase. The

appliance adds some rinses.

2)

During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't rotate or

doesn't rotate properly, but this is normal for this programme.

3)

Set this programme to decrease the energy and water consumption maintaining a good washing performance.

4)

Standard programmes for the Energy Label consumption values. According to regulation 1061/2010,

these programmes are respectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton pro‐

gramme». They are the most efficient programmes in terms of combined energy and water consumption for

washing normally soiled cotton laundry.

The water temperature of the washing phase may differ from the temperature declared for the se‐

lected programme.

5)

If you set a Steam programme with dried laundry, at the end of the cycle the laundry could be humid. It is

better to expose the items to the fresh air for about 10 minutes to let the humidity dry. When the programme is

completed, quickly remove the laundry from the drum. After a steam cycle, items may be ironed however with

less effort.

6)

Steam does not remove animal odours.

11

Programme options compatibility

Programme

U./Min. - T/min.

Flecken - Taches / Vorwäsche - Prélavage

1)

Extra Spülen - Rinçage +

2)

Zeit Sparen - Gain de Temps

3)

Zeitvorwahl - Départ Différé

Koch/Bunt - Blanc/Couleurs

■ ■ ■ ■ ■ ■

Extra Leise - Extra Silence

■ ■ ■ ■

Pflegeleicht - Synthétiques

■ ■ ■ ■ ■ ■

Leichtbügeln - Repassage

Facile

■ ■

■

4)

■ ■ ■

Feinwäsche - Délicats

■ ■ ■ ■ ■ ■

Wolle/Seide - Laine/Soie

■ ■ ■

Daunen - Couette

■ ■

Anti-Allergie - Anti-Allergies

■ ■ ■ ■ ■

Schleudern/Pumpen - Es‐

sorage/Vidange

5)

■ ■ ■

12

Programme

U./Min. - T/min.

Flecken - Taches / Vorwäsche - Prélavage

1)

Extra Spülen - Rinçage +

2)

Zeit Sparen - Gain de Temps

3)

Zeitvorwahl - Départ Différé

Spülen - Rinçage

Cold

■ ■ ■ ■

Jeans

■ ■

■

4)

■ ■ ■

20 min.-3 kg ■ ■

Super Eco 30° ■ ■ ■ ■

Baumwolle Eco - Coton Eco

■ ■ ■ ■

■

6)

■

1)

If you use liquid detergent, set a programme without Prewash. The Stain option is not available with a temper‐

ature lower than 40°C.

2)

With a low spin speed the appliance performs delicate rinses and a short spin.

3)

If you set the shortest duration, we recommend that you decrease the load size. It is possible to fully load the

appliance, however the washing results can be less satisfactory.

4)

Only the Prewash function is available.

5)

Set the spin speed. Make sure it is suitable for the type of fabric being washed. If you set the No Spin option

then only the drain phase is available.

6)

With these programmes you can set only the shorter duration.

13

Woolmark Apparel Care - Green

The wool wash cycle of this machine has

been approved by The Woolmark

Company for the washing of wool

garments labelled as «hand wash»

provided that the garments are washed

according to the instructions issued by the

manufacturer of this washing machine.

Follow the garment care label for drying

and other laundry instructions. M1361

In UK, Eire, Hong Kong and India the

Woolmark symbol is a certification

trademark.

CONSUMPTION VALUES

Stated values are obtained in laboratory conditions with relevant stand‐

ards. Different causes can change the data: the quantity and type of laun‐

dry and ambient temperature. Water pressure, the supply voltage and the

temperature of inlet water may also affect the washing programme dura‐

tion.

Technical specifications may be changed without prior notice to improve

the quality of product.

At the start of the programme, the display shows the programme duration

for the maximum load capacity.

During the washing phase the programme duration is automatically cal‐

culated and can be greatly reduced if the laundry load is lower than the

maximum load capacity (e.g. Cotton 60°C, maximum load capacity 9 kg,

the programme duration exceeds 2 hours; actual load 1 kg, the pro‐

gramme duration will be less than 1 hour).

When the appliance is calculating the real programme duration a dot

flashes in the display.

Programmes Load

(kg)

Energy

consump‐

tion (kWh)

Water

consump‐

tion (litre)

Approxi‐

mate pro‐

gramme

duration

(minutes)

Remain‐

ing mois‐

ture (%)

1)

Koch/Bunt - Blanc/

Couleurs 60°C

9 1,55 87 220 44

Koch/Bunt - Blanc/

Couleurs 40°C

9 0,97 87 205 44

14

Programmes Load

(kg)

Energy

consump‐

tion (kWh)

Water

consump‐

tion (litre)

Approxi‐

mate pro‐

gramme

duration

(minutes)

Remain‐

ing mois‐

ture (%)

1)

Pflegeleicht - Syn‐

thétiques 40°C

4 0,72 55 155 35

Feinwäsche - Déli‐

cats 40°C

4 0,60 59 89 35

Wolle/Seide -

Laine/Soie 30°C

2)

2 0,35 58 60 30

Standard cotton programmes

Standard 60°C cot‐

ton

9 0,640 57 226 44

Standard 60°C cot‐

ton

4.5 0,349 41 185 44

Standard 40°C cot‐

ton

4.5 0,347 40 199 44

1)

At the end of spin phase.

2)

Not available for some models.

Off Mode (W) Left On Mode (W)

0.05 0.05

The information given in the chart above is compliant with the EU Commission regulation

1015/2010 implementing directive 2009/125/EC .

OPTIONS

Start/Pause - Départ/Pause

Press button Start/Pause - Départ/Pause

to start or interrupt a programme.

Zeitvorwahl - Départ Différé

With this option you can delay the start of

a programme from 30 minutes to 20

hours.

The display shows the related indicator

and delay time.

Zeit Sparen - Gain de Temps

With this option you can decrease the

programme duration.

• Press this button one time to set

'Shortened duration' for items with daily

soil.

• Press this button two times to set 'Extra

Quick' for items with almost no soil.

Some programmes accept only

one of the two options.

15

Extra Spülen - Rinçage +

With this option you can add some rinses

to a washing programme.

Use this option for persons allergic to

detergents and in areas where the water

is soft.

The related indicator comes on.

Flecken - Taches / Vorwäsche -

Prélavage

Press this button to add the stain and/or a

prewash phase to a programme.

Press the button again and again to

activate one or two options. The related

symbol and the indicator bar comes on in

the display.

• Flecken - Taches: Use this option for

laundry with hard stains to remove.

When you set this option, put the stain

remover into compartment . This

function increases the programme

duration.

This option is not available

with a temperature lower

than 40° C.

• Vorwäsche - Prélavage: Use this

option to add a prewash phase before

the washing phase.

We recommend that you use this

option when you have laundry with a

high level of soil.

The set of this option

increases the programme

duration.

U./Min. - T/min.

Press this button to:

• Decrease the maximum speed of the

spin phase of the programme.

The display shows only the

spin speeds available with

the set programme.

• Deactivate the spin phase.

• Activate the Rinse Hold function.

Set this function to prevent fabric

creases. The appliance does not drain

the water when the programme is

completed.

Temperatur - Température

Press this button to change the default

temperature. When the display shows

and , the appliance does not heat the

water.

SETTINGS

Acoustic signals

The acoustic signals operate when:

• You activate the appliance.

• You deactivate the appliance.

• You press the buttons.

• The programme is completed.

• The appliance has a malfunction.

To deactivate/activate the acoustic

signals, press Flecken/Vorw. - Taches/

Prélavage and Extra Spülen - Rinçage

Plus at the same time for 6 seconds.

If you deactivate the acoustic

signals, they continue operate

when the appliance has a

malfunction.

Child Lock

With this option you can prevent that the

children play with the control panel.

• To activate/deactivate this option,

press Temp. and U./Min. - Essorage at

the same time until the indicator

comes on/goes off.

You can activate this option:

• After you press Start/Pause - Départ/

Pause : the options and the programme

knob are locked.

• Before you press Start/Pause - Départ/

Pause : the appliance cannot start.

16

Permanent Extra Rinse

With this option you can permanently have

an extra rinse when you set a new

programme.

• To activate/deactivate this option

press Zeit Sparen - Gain de Temps and

Zeitvorwahl - Départ Différé at the

same time until the relevant indicator

comes on/goes off.

BEFORE FIRST USE

1. Connect the mains plug to the mains

socket.

2. Open the water tap.

3. Put a small quantity of detergent in the

compartment for washing phase.

4. Set and start a programme for cotton

at the highest temperature without

laundry.

This removes all possible dirt from the

drum and the tub.

DAILY USE

WARNING! Refer to Safety

chapters.

Activating the appliance

1. Connect the mains plug to the mains

socket.

2. Open the water tap.

3. Press button Auto Off to activate the

appliance.

A short tune sounds.

Loading the laundry

1. Open the appliance door

2. Shake the items before you put them

in the appliance.

3. Put the laundry in the drum, one item

at a time.

Make sure not to put too much laundry in

the drum.

4. Close the door firmly.

Washing heavily oiled, greasy

stains could cause damage

rubber parts of the washing

machine.

Filling the detergent and

additives

17

Compartment for prewash phase an

soak programme.

Compartment for washing phase.

Compartment for liquid additives

(fabric conditioner, starch).

Maximum level for quantity of liquid

additives.

Compartment for stain remover.

Flap for powder or liquid detergent.

Always follow the instructions

that you find on the packaging

of the detergent products.

Check the position of the flap

1. Pull out the detergent dispenser until it

stops.

2. Press the lever down to remove the

dispenser.

1

2

3. To use powder detergent, turn the flap

up.

A

4. To use liquid detergent, turn the flap

down.

B

With the flap in the position

DOWN:

• Do not use gelatinous or

thick liquid detergents.

• Do not put more liquid

detergent than the limit

shown on in the flap.

• Do not set the prewash

phase.

• Do not set the delay

start function.

5. Measure out the detergent and the

fabric conditioner.

6. Carefully close the detergent

dispenser.

Make sure that the flap does not cause a

blockage when you close the drawer.

Setting a programme

1. Turn the programme knob. The related

programme indicator comes on.

The indicator of button Start/Pause -

Départ/Pause flashes with red colour.

The display shows the default

temperature, the spin speed and the

empty indicator bars of the available

functions.

2. To change the temperature and/or the

spin speed, press the related buttons.

3. Set the available functions.

Starting a programme without

the delay start

Press button Start/Pause - Départ/Pause

to start the programme.

18

The relevant indicator stops to flash and

stays on.

On the display the indicator of the phase

is operation starts to flash.

The programme starts, the door is locked.

The display show the indicator .

The drain pump can operate for

a short time when the

appliance fills water.

Starting a programme with the

delay start

1. Press button Zeitvorwahl - Départ

Différé again and again until the

display shows the number of minutes

or hours of delay.

The related indicator comes on.

2. Press button Start/Pause - Départ/

Pause.

The appliance starts the countdown of the

delay start.

When the countdown is completed, the

programme starts automatically.

Before you press button Start/

Pause - Départ/Pause to start

the appliance, you can cancel

or change the set of the delay

start.

Cancelling the delay start

To cancel the delay start:

1. Press button Start/Pause - Départ/

Pause to set the appliance to pause.

The related indicator flashes.

2. Press button Zeitvorwahl - Départ

Différé repeatedly until the display

shows

.

3. Press button Start/Pause - Départ/

Pause again to start the programme

immediately.

Cycle time recalculation

After approximately 15 minutes

from the start of the

programme:

• The appliance adjusts

automatically the cycle time

to the laundry you have put

in the drum to have perfect

washing results in the

minimum necessary time.

• The display shows the new

time value.

Cancelling a running

programme

1. Press button Auto Off to cancel the

programme and to deactivate the

appliance.

2. Press button Auto Off again to activate

the appliance.

Now, you can set a new washing

programme.

Before starting the new

programme the appliance could

drain the water. In this case,

make sure that the detergent is

still in the detergent

compartment, if not fill the

detergent again.

Interrupting a programme and

changing a option

You can change only some options before

they operate.

1. Press button Start/Pause - Départ/

Pause.

The related indicator flashes.

2. Change the option set.

3. Press the button Start/Pause - Départ/

Pause again.

The programme continues.

19

Opening the door

If the temperature and level of

the water in the drum are too

high and/or the drum still

rotates you cannot open the

door.

While a programme or the delay start

operates, the appliance door is locked.

1. Press button Start/Pause - Départ/

Pause.

In the display the related door lock

indicator goes off.

2. Open the appliance door.

3. Close the door and press button Start/

Pause - Départ/Pause.

The programme or the delay start

continues.

End of cycle

When the programme has finished, the

appliance stops automatically. The

acoustic signal operates (if it is active).

In the display

comes on and the door

locked indicator goes off.

The indicator of Start/Pause - Départ/

Pause button goes off.

1. Press button Auto Off to deactivate the

appliance.

After five minutes from the end of the

programme, the energy saving function

automatically deactivates the appliance.

When you activate the

appliance again, the display

show the end of the last set

programme. Turn the

programme knob to set a new

cycle.

2. Remove the laundry from the

appliance.

3. Make sure that the drum is empty.

4. Keep the door ajar, to prevent mildew

and odours

Draining water out after end of

cycle

The washing programme is completed,

but there is water in the drum:

The drum turns regularly to prevent the

creases in the laundry.

The door lock indicator is on. The

door stays locked.

You must drain the water to open the

door:

1. If necessary, decrease the spin speed.

2. Press the Start/Pause - Départ/Pause

button.

The appliance drains the water and spins.

3. When the programme is completed

and the door lock indicator

goes

off, you can open the door .

4. Press Auto Off some seconds to

deactivate the appliance.

The appliance drains and spins

automatically after

approximately18 hours.

AUTO OFF option

The AUTO OFF function automatically

deactivates the appliance to decrease the

energy consumption when:

• You do not use the appliance for 5

minutes before you press Start/Pause -

Départ/Pause button.

Press the button Auto Off to activate

the appliance again.

• After 5 minutes from the end of the

washing programme

Press the button Auto Off to activate

the appliance again.

The display shows the end of the last

set programme.

Turn the programme knob to set a new

cycle.

If you set a programme or an

option that ends with water in

the drum, the AUTO OFF

function doesn't deactivate

the appliance to remind you to

drain the water.

20

Page is loading ...

FORS WE9567 User manual

FORS WE9567 User manual

in other languages

Related papers

Other documents