InSinkErator H-VIEWSN-SS User manual

Brand: InSinkErator

Model: H-VIEWSN-SS

Category: Water dispensers

Type: User manual

INVOLVE VIEW

™

INVOLVE WAVE

™

INVITE CONTOUR

™

INVITE CLASSIC

™

1.800.558.5700

www.insinkerator.com

The Emerson logo is a trademark and a service mark of Emerson Electric Co.

InSinkErator may make improvements and/or changes in the specifications at any time, in its sole discretion,

without notice or obligation and further reserves the right to change or discontinue models.

El logotipo Emerson es una marca registrada y una marca de servicio de Emerson Electric Co.

InSinkErator puede realizar mejoras y/o modificaciones en las especificaciones en cualquier momento, y bajo su exclusivo

criterio, sin previo aviso u obligación; además, se reserva el derecho de cambiar o suspender los modelos.

Le logo Emerson est une marque de commerce et de service d'Emerson Electric Co.

InSinkErator se réserve le droit, à son entière discrétion, d’apporter en tout temps des améliorations ou des modifications

aux spécifications, et ce, sans préavis ou obligation de sa part, ou de modifier ou de supprimer des modèles.

44671 REV A

Instant Hot Water Dispenser

Owner’s Manual

Installation, Care & Use

Instalación, cuidado y uso

Installation, soin et utilisation

Dispensador de agua caliente instantánea

Manual del usuario

Distributeur d’eau très chaude instantanée

Manuel du propriétaire

INVOLVE VIEW

™

INVOLVE WAVE

™

INVITE CONTOUR

™

INVITE CLASSIC

™

To see a tutorial of this installation:

http://goo.gl/AZOHu

Para ver un tutorial de esta instalación ingrese a

Pour voir un tutoriel de cette installation

Unpack dispenser components.

On a firm, flat surface, carefully

straighten the copper tubing using

hands only.

View/Wave

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

INSTALLING THE FAUCET - VIEW/WAVE

HOW TO USE THIS INSTRUCTION MANUAL

These instructions are separated into main sections, indicated by numbers, and subsections,

indicated by capital letters. The manual is setup this way to allow you to take a break at any

point after completing a section or subsection without affecting the installation process.

What you’ll see in the

instruction manual:

OVERVIEW OF A

COMPLETED SETUP

H-Contour-SS H-Classic-SSH-View-SS H-Wave-SSHC-View-SS HC-Wave-SS

Identify the model of your instant hot water dispenser and record it here:______________________

Equipment You May Need:

We are delighted that you have chosen the InSinkErator

Instant Hot Water Dispenser to be

a part of your home. This unique appliance will save you time and effort in the kitchen, and

you’ll enjoy discovering new uses for it each day. That’s exactly why millions of people are

now using an InSinkErator Instant Hot Water Dispenser.

We are confident that by following our step-by-step instructions, you’ll soon be enjoying the

convenience of instant hot water.

For your satisfaction and safety, read all instructions, cautions and warnings before installing or using this

instant hot water dispenser.

This particular unit is not intended for commercial use.

Make sure that all electrical wiring and connections conform to local codes.

A standard 115-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power.

The wall outlet powering your dispenser must have power supplied to it continuously.

This outlet must be fused and should not be controlled by the same wall switch that operates the disposer,

unless you have a SinkTop Switch

™

from InSinkErator

It is recommended that a dedicated control valve be installed on the cold water line supplying water to this

system.

If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation

of this unit, it is recommended to use our water filtration system.

This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the

number of factors that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty

water discharged from the hot water dispenser may indicate the need for service or replacement of this product.

The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).

If it does, this will prevent your unit from operating properly.

Moving parts inside the tank causing a rattling noise is normal.

WHAT YOU SHOULD KNOW BEFORE YOU BEGIN

Equipment Required:

n Drill

n T-fitting

n Dedicated control valve

n Adjustable wrench

n Phillips and flat blade screwdrivers

n Pencil

n Tape Measure / Ruler

n Level

Anchors for drywall

Hole saw

Basin wrench

Hole punch

If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench

and a 1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line. See Step 1-B.

If you need to cut a mounting hole in your stainless steel sink, you may need a 1-1/4" – 1-1/2" hole

saw made for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a

surface other than stainless steel.

WHAT YOU NEED TO GET STARTED

Provides a step-by-step narrative describing the installation step, with check boxes that

can be marked as you progress through the installation.

Contains simple illustrations that provide visual instruction to support the narrative.

Important safety messages that will require your attention during the step.

Warning indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

Caution indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

Notice is used to address practices not related to personal injury.

NOTICE

To see a tutorial of this installation:

http://goo.gl/AZOHu

NOTICE

The wall outlet for your dispenser must have power supplied to it continuously

and must be fused. It should not be controlled by the same wall switch

that operates your disposer, unless using an InSinkErator SinkTop Switch

™

*component parts pre-installed on dispenser

PREPARATION

START HERE

Identify locations for the dispenser

faucet, tank and filter (if applicable).

Check to make sure there is proper

clearance (see chart at left) for

dispenser handles to be fully opened.

Check to make sure counter is not

too thick (see chart at left).

Make sure there is a grounded

electrical outlet under the sink.

Turn off water supply.

If using the sink sprayer hose hole,

remove nut that connects sprayer

hose at bottom of faucet.

Using adjustable wrench, remove

nut connecting sprayer washer

flange in sprayer hole.

Plug hose opening with either a 1/8"

plug or a 1/4" cap (not supplied).

If you have to drill through sink or

countertop, you may need to rent or

purchase the appropriate tools.

Consult a professional before drilling into

a surface other than stainless steel.

Required minimum

from center of hole

to wall

Maximum counter

thickness (depth)

What if you don’t have a sprayer hole

or don’t want to use it?

Many homeowners replace the

soap dispenser in their sink with an

instant hot water dispenser.

If drilling a hole into a stainless steel

sink or counter top, you can cut

a mounting hole for the dispenser

with a hole saw for stainless steel,

or you can use a hole punch.

Required Hole Size

1-1⁄4" – 1-1⁄2"

Dependent on model

HC-View-SS ..... 2-5⁄8" .................... 3"

H-View-SS ....... 2-5⁄8" .................... 3"

HC-Wave-SS .... 2-5⁄8" .................... 3"

H-Wave-SS ...... 2-3⁄8" .................... 3"

H-Contour-SS ... 2" ...........................3"

H-Classic-SS .... 2" ........................... 3"

COMPONENTS IN THIS PACKAGE

H-Classic-SS

Semi-Circular

Mounting Plate

Flat Gasket

Wing Nut

Trim Ring

3/4" Screws (2)

HC-View-SS

H-View-SS

H-Wave-SS

HC-Wave-SS

Small Steel* FiberRubber* Large Steel

Washers

1-1/2"

1-1/4" 1-1/4"

1-5/16"

3/8" Tube

Brass Nut / Ferrule /

Tube Insert

Quick Connector

3/4" Screws (2)

Extension & Star Nut*

Small Steel* FiberRubber* Large Steel

Washers

1-1/2"

1-1/4"

Semi-Circular

Mounting Plate

Flat GasketWing Nut

3/4" Screws (2)

1-1/4"

1-5/16"

3/4" Screws (2)

Extension & Star Nut*

H-Contour-SS

Tank

To see a tutorial of this installation:

http://goo.gl/AZOHu

Unpack dispenser components.

On a firm, flat surface, carefully

straighten the copper tubing using

hands only.

Unscrew and remove threaded extension

from valve body. Do not discard, as you

will need this later (See Figure 1).

Leave small washers in place.

Feed tubes down through the hole in

the sink/counter until the base is at

rest. Set faucet at desired angle.

From under sink, slide 1-1/2" fiber washer

over faucet base. Reinstall threaded

extension onto the base until snug.

Thread star nut onto extension until

snug (See Figure 2).

From under sink, slide 1-1/2" fiber washer

over threaded extension. Thread star

nut onto extension until snug.

Hot & Cool models only

Attach the quick connector to the

ends of the copper tubes running

from the dispenser.

Install a white 3/8" tube into other

end of quick connector.

If sink/counter thickness exceeds 3/4"

a hole diameter of 1-1⁄2" is required.

An assistant may be needed to hold

the dispenser head in place

while securing the dispenser.

View/Wave

Hot & Cool models only

For a standard 1-1⁄2" sink/counter hole

Feed tubes down through the hole in

the sink/counter until the base is at

rest. Set faucet at desired angle.

Large washer required for sink holes

larger than 1-1⁄ 2" or for porcelain sinks

with radius or beveled holes.

Before feeding tubes through sink

hole, remove extension. Place 1-5/16"

large steel washer over threads on

faucet base. Reinstall extension.

View/Wave

Faucet is factory-ready for installation

into a standard 1-1⁄2" sink/counter hole.

1-1/4"

Small

Steel

Washer

Fiber

Washer

Star Nut

1-5/16" Large

Steel Washer

1-1/4"

Small

Rubber

Washer

Standard 1-1⁄2" hole Hole larger than 1-1⁄2"

Installing into hole smaller than 1-1⁄2"

Figure 1 Figure 2

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

1-1/4" Small

Steel Washer

Fiber

Washer

Star Nut

1-1/4" Small

Rubber Washer

1-1/4"

Small

Steel

Washer

1-1/4"

Small

Rubber

Washer

INSTALLING THE FAUCET - View/Wave

Property Damage: Do not pinch or break copper

tubing. Do not distort the last 1 inch of tubing.

Make sure to use rubber gasket

to ensure proper seal.

Unpack dispenser components.

On a firm, flat surface, carefully

straighten the copper tubing using

hands only.

Install chrome trim ring

onto base of faucet.

Ensure that the flat gasket is

properly seated into the base

of the dispenser head and will

surround the sink mount.

Feed tubes down the hole in

the sink or countertop until the

base is at rest on the sink or

countertop surface.

From under the sink, place the

semi-circular mounting plate onto

the threaded stud.

Place wing nut onto the threaded

stud. Make sure faucet head is

at the desired angle. Tighten the

wing nut until snug, while ensuring

the semi-circular mounting plate

extends beyond the sink hole.

Do not over tighten wing nut. May cause

damage to faucet.

An assistant may be needed to hold

the dispenser head in place

while securing the dispenser.

Contour/Classic

INSTALLING THE FAUCET

Contour/Classic

NOTICE

Flat

Gasket

Trim

Ring

To see a tutorial of this installation:

http://goo.gl/AZOHu

Select a spot under the sink to mount

tank vertically within reach of both

plumbing and electrical connections.

The tank should be within 16" or less

of faucet water lines and within 30"

or less of a standard grounded outlet.

While holding tank in place on

the spot selected for installation,

use a pencil to mark locations for

2 hanging screws.

Property Damage: Tank must be located

within 16" of faucet and within 30" or less

of a standard grounded outlet. DO NOT extend

plumbing or electrical lines.

Without depressing the gray button,

place the snap-connect fitting at

the end of the blue 1/4" tube onto

the left fitting on the tank, pushing

until it clicks into place. (1)

Slip the flexible white 7/16" tube

over barbed middle fitting and slide

down approximately 1/2". (2)

Slip the clear 5/16" tube over the

far right smooth fitting and slide

down approximately 1/2". (3)

Visually check for pinched or

crimped tubes.

Property Damage: Pinched or blocked water

lines may cause damage to the dispenser tank.

Check to make sure tubes are connected

properly and are pushed down as far as possible.

Tank must be

mounted level

to ensure

proper operation.

Hose clamps are not needed for any

of the connections.

Mount tank vertically in an area that

allows clearance on the underside of

the tank for drainage, if necessary.

DO NOT over tighten screws.

Pre-drill 1/8" pilot holes at marks.

Turn screws into pre-drilled holes,

leaving 1/4" exposed.

Hang the tank on the screws.

Tighten the screws with only 1/2

turn clockwise.

Screws provided are for use in wood

studs or cabinets only. Use wall anchors

(not supplied) for installation into drywall.

Leave 1/4" for

hanging tank.

Brass Nut

Ferrule

Brass Insert

Wing Nut

Fiber

Washer

Brass Nut

Ferrule

Wing Nut

Fiber

Washer

Plastic

tube

Brass Nut

Ferrule

Brass Insert

Wing Nut

Fiber

Washer

Brass Nut

Ferrule

Wing Nut

Fiber

Washer

Plastic

tube

Brass Nut

Ferrule

Brass Insert

Wing Nut

Fiber

Washer

Brass Nut

Ferrule

Wing Nut

Fiber

Washer

Plastic

tube

(1) (2) (3)

MOUNTING THE TANK

CONNECTING FAUCET TO TANK

NOTICE

Scalding Hazard: The faucet dispenses

near-boiling (212ºF) water which can

instantly cause scalds or burns. Use care

when operating this appliance.

Property Damage: Join remaining tube

to cold water supply only.

Property Damage: Join remaining tube

to cold water supply only.

Turn on the cold water supply.

Depress the dispenser’s HOT

handle and hold it until water flows from

the spout (approximately 1 to

2 minutes).

Run the water for at least 2 minutes to

flush lines (both the hot and cold handles

independently if applicable).

Check all connections to ensure they are

tight and that there are no leaks.

Plug in instant hot water tank.

Water will be cold at first.

Allow 12-15 minutes for water to reach

target temperature.

Gurgling or hissing is normal during the

initial heating cycle.

Install a T-fitting (not included) onto the

cold water supply line.

Install dedicated water control valve with

3/8" compression fitting.

At the end of the white 3/8" tube from

the quick-connector, slide the supplied

brass nut and ferrule over the tube and

then push in the brass tube insert.

Insert the white 3/8" tube into the 3/8"

compression fitting and tighten.

HC-View/HC-Wave

Install a T-fitting (not included) onto the

cold water supply line.

Install dedicated water control valve with

1/4" compression fitting (not included).

At the end of the copper 1/4" tube,

slide the brass nut and ferrule provided

with the control valve over the tube.

Insert the copper tube into the 1/4"

compression fitting and tighten.

H-View/H -Wave/Contour/Classic

Electric Shock Hazard: A standard grounded

outlet within 30" of the dispenser is required

under the sink. Do not use an extension

cord set with the dispenser.

Brass Nut

Ferrule

Brass Insert

Wing Nut

Fiber

Washer

Brass Nut

Ferrule

Wing Nut

Fiber

Washer

Plastic

tube

FINAL WATER CONNECTION

FILL TANK & THEN CONNECT POWER

NOTICE

3/8"

Plastic

Tube

Brass

Nut

Brass

Insert

Ferrule

1/4"

Copper

Tube

Brass

Nut

Ferrule

Brass Nut

Ferrule

Brass Insert

Wing Nut

Fiber

Washer

Brass Nut

Ferrule

Wing Nut

Fiber

Washer

Plastic

tube

To see a tutorial of this installation:

http://goo.gl/AZOHu

Electric Shock Hazard: Using an ungrounded or improperly connected

appliance can result in serious injury or death from electrical shock.

Property Damage: To avoid water damage, replace any loose or split tubing.

Periodically inspect the unit for any signs of leakage and immediately remove from

service any unit suspected of leaking.

Personal Injury: This tank is a non-pressurized tank. DO NOT modify this system.

DO NOT close vent tube or connect other type dispensers or valves to the tank. Use

only the InSinkErator dispenser faucet supplied. Use only parts provided. Contact an

authorized InSinkErator Service agent for repairs or replacement components.

This appliance must be grounded. This instant hot water dispenser is equipped with a cord that has a

grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided

with the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Check

with a qualified electrician or serviceman if you are in doubt as to whether the instant hot water dispenser is

properly grounded.

Fire Hazard: To minimize possibility of fire, DO NOT store flammable items such as

rags, paper or aerosol cans near the tank. DO NOT store or use gasoline or other

flammable vapors and liquids in the vicinity of this or any other appliance.

Leak Hazard: Regularly inspect dispenser and plumbing fittings for leaks, which can

cause property damage and/or could result in personal injury.

An instant hot water dispenser, like any water heater, has a limited life and will eventually

fail. To avoid possible property damage and personal injury, this instant hot water dispenser

should be regularly examined for leakage and/or corrosion and replaced when necessary.

A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be

used in those applications where any leakage could cause property damage. To check

for corrosion, examine the appearance of the dispensed water in a clear glass once every

three (3) months. If there is any discoloration or rusty appearance, unplug and drain unit as

described in the Seasonal Storage/Drainage section on page 12 of this manual. If the water

discoloration remains after draining and refilling unit, discontinue use and contact an

authorized InSinkErator service agent.

NOTICE

This warranty is provided by InSinkErator

, a business unit of Emerson Electric Co., (“InSinkErator” or “Manufacturer” or

“we” or “our” or “us”) to the original consumer owner of the InSinkErator product with which this warranty is provided (the

“InSinkErator Product”), and any subsequent owner of the residence in which the Product was originally installed (“Customer”

or “you” or “your”).

InSinkErator warrants to Customer that your InSinkErator Product will be free from defects in materials and workmanship,

subject to the exclusions described below, for a period of 3 years (the “Warranty Period”), commencing on the later of: (a)

the date your InSinkErator Product is originally installed, (b) the date of purchase, or (c) the date of manufacture as identified

by your InSinkErator Product serial number. You will be required to show written documentation supporting (a) or (b). If you are

unable to provide documentation supporting either (a) or (b), the Warranty Period commencement date will be determined by

Manufacturer, in its sole and absolute discretion, based upon your InSinkErator Product serial number.

Permitted Uses

You may use your InSinkErator Product hot/cold water tank and filter system in combination with any genuine InSinkErator

Product instant hot water dispensers and component parts, and with any authentic Dornbracht hot or hot/cold water dispensers

and component parts (collectively, “Dornbracht Water Dispenser”) which Dornbracht expressly states in writing is/are compatible

with such InSinkErator Product(s). Use of your InSinkErator Product with any other manufacturer’s products or in any combination

other than as expressly stated above will void this warranty.

What is Covered

This warranty covers defects in materials or workmanship, subject to the exclusions below, in InSinkErator Products used

by a consumer Customer for residential use only, and includes all replacement parts and labor costs. YOUR SOLE AND

EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE

INSINKERATOR PRODUCT, PROVIDED, THAT IF WE DETERMINE IN OUR SOLE DISCRETION THAT NEITHER REMEDY

IS PRACTICABLE, WE MAY PROVIDE YOU WITH A REFUND OF YOUR PURCHASE PRICE OR A CREDIT TOWARDS

ANOTHER INSINKERATOR PRODUCT.

What is not Covered

This limited warranty does not extend to and expressly excludes:

 • LossesordamagesortheinabilitytooperateyourInSinkEratorProductresultingfromconditionsbeyondthe

Manufacturer’s control including, without limitation, accident, alteration, misuse, abuse, neglect, negligence (other than

Manufacturer’s), failure to install, maintain, assemble, or mount the InSinkErator Product in accordance with

Manufacturer’s instructions or local electrical and plumbing codes.

 • Wearandtearexpectedtooccurduringthenormalcourseofuse,includingwithoutlimitation,cosmeticrust,scratches,

dents or comparable and reasonably expected losses or damages.

 • LossesordamagescausedbytheDornbrachtWaterDispenser

In addition to the above exclusions, this warranty does not apply to InSinkErator Products installed in a commercial or

industrial application.

No Other Express Warranty Applies

This warranty is the sole and exclusive warranty provided to the Customer identified above. No other express warranty, written

or verbal, applies. No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other

warranty on behalf of Manufacturer. The terms of this warranty shall not be modified by the Manufacturer, the original owner, or

their respective successors or assigns.

What we will do to Correct Problems

If your InSinkErator Product does not operate in accordance with the documentation provided to you, or you have questions

concerning your InSinkErator Product or how to determine when service is needed, please call the toll free InSinkErator

AnswerLine at 1 (800) 558-5700, or visit our website at www.insinkerator.com. You may also notify us at: InSinkErator Service

Center, 4700 21st Street, Racine, Wisconsin 53406 USA.

The following information must be provided as part of your warranty claim: your name, address, phone number, your

InSinkErator Product model and serial number, and if necessary, upon request, written confirmation of either: (a) the date shown

on your installation receipt, or (b) the date shown on your purchase receipt.

Manufacturer or its authorized service representative will determine, in its sole and absolute discretion, if your InSinkErator Product

is covered under this warranty. You will be given the contact information for your closest authorized InSinkErator Service Center.

Please contact your InSinkErator Service Center directly to receive in home warranty repair or replacement service. Only an

authorized InSinkErator service representative may provide warranty service. InSinkErator is not responsible for warranty claims

arising from work performed on your InSinkErator Product by anyone other than an authorized InSinkErator service representative.

If a covered claim is made during the Warranty Period, Manufacturer will, through its authorized service representative, either

repair or replace your InSinkErator Product. Cost of replacement parts or a new InSinkErator Product, and cost of labor for repair

or installation of the replacement InSinkErator Product are provided at no cost to you. Repair or replacement shall be determined

by Manufacturer or its authorized service representative in their sole discretion. All repair and replacement services will be provided

to you at your home. If Manufacturer determines that your InSinkErator Product must be replaced rather than repaired, the

warranty on the replacement InSinkErator Product will be limited to the unexpired term remaining in the original Warranty Period.

Limitation of Liability

TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL MANUFACTURER OR ITS AUTHORIZED SERVICE

REPRESENTATIVES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING

ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE

INSINKERATOR PRODUCT OR THE MANUFACTURER’S OR ITS AUTHORIZED SERVICE REPRESENTATIVE’S NEGLIGENCE.

MANUFACTURER SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT,

REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT,

NEGLIGENCE, STRICT LIABILITY, OTHER SORT OR OTHERWISE), SHALL MANUFACTURER’S LIABILITY TO YOU EXCEED THE

PRICE PAID BY THE ORIGINAL OWNER FOR THE INSINKERATOR PRODUCT.

The term “consequential damages” shall include, but not be limited to, loss of anticipated profits, business interruption, loss of

use or revenue, cost of capital or loss or damage to property or equipment.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not

apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

IN-HOME FULL SERVICE LIMITED WARRANTYIMPORTANT SAFETY INSTRUCTIONS

InSinkErator

may make improvements and/or changes in the specifications at any time, in its sole

discretion, without notice or obligation and further reserves the right to change or discontinue models.

Electric Shock Hazard: To prevent electrical shock, disconnect power before

servicing unit. Use only a properly grounded and polarized electric outlet.

Scalding Hazard: Do not allow

water to boil. May result in

severe burns.

Factory temperature pre-set

is approximately 200˚F.

Adjust the thermostat

slowly, turning the dial

clockwise to increase

temperature or counter

clockwise to decrease

temperature, then activate faucet handle

for 20 seconds to bring in fresh water

to be heated at the new setting. Allow

5-7 minutes for water to reach new

temperature.

To reset the thermostat to 200°, turn the indicator

two notches to the right of vertical.

Regularly inspect the unit for any signs

of leakage. If there are signs of water

damage, immediately remove the unit

from service.

To avoid water damage from leakage,

replace all cut, loose or split tubing.

A drain pan, plumbed to an appropriate

drain or outfitted with a leak detector,

should be used in those applications

where any leakage could cause

property damage.

PROPERTY DAMAGE

CARE AND USE

approx. 200°

Only use mild cleaners to clean the

faucet and plastic components.

Cleaners with acids, abrasives, alkaline

or organic solvents will result in

deterioration of the plastic components

and void the warranty.

CLEANING THE FAUCET AND TANK

Anytime the instant hot water dispenser is not used

for extended periods of time, unplug and drain unit.

If it is below freezing you will need to unplug the unit

and drain it.

SEASONAL STORAGE/DRAINAGE

ADJUSTING THE THERMOSTAT

For fresher tasting water, add filtration to your

instant hot water dispenser system. InSinkErator

offers water filtration systems designed exclusively

for instant hot water dispensers. For more

information, visit www.insinkerator.com or

shop.insinkerator.com.

Regularly check for signs of corrosion

by examining the appearance of the

dispensed water.

If there is any discoloration or rusty

appearance, unplug and drain unit

as described in the Seasonal

Storage/Drainage section on this

page of the manual.

If the water discoloration remains

after draining and refilling unit,

discontinue use and contact an

authorized InSinkErator service agent.

PERSONAL INJURY

Disconnect power from unit (unplug unit).

Push hot water dispenser faucet lever

and allow water to flow until it is cool.

Shut the cold water supply off at the valve.

Disconnect tubes from the tank.

Unhook tank from wall.

Hold tank upside down and drain the

water into the sink.

Towel dry any water drippings from

tank area.

Reinstall tank to wall and reconnect tubes.

Remove and discard filter cartridge,

if applicable.

To put back into working order, install

new filter cartridge (if applicable) and

turn on cold water supply at valve.

Depress the hot water dispenser faucet

lever and hold until water flows from the

spout. Reconnect the electrical cord.

(Refer to Page 9, Step 6B)

NOTICE

TROUBLESHOOTING

WHAT TO DO

Water and steam spits

forcefully from spout

without turning on the

dispenser faucet.

Water is not hot.

• Unit is boiling.

May be normal during initial setup.

• The unit is unplugged.

• The electric outlet is inoperative.

• Activate faucet lever to release some water from

the tank.

• Adjust water temperature using dial on tank front.

Remember that at higher altitudes, water boils

at lower temperatures.

• Make sure the unit is connected to a properly

grounded electric outlet.

• Make sure the circuit breaker or fuses are

functioning properly.

• Check that the outlet is not switched off.

Water is too hot

or not hot enough.

• Thermostat is not adjusted to

your needs.

• Adjust the thermostat slowly, then activate faucet

lever for 20 seconds to bring in fresh water to be

heated at the new setting. Allow 5-7 minutes for

water to reach new temperature.

Water comes out the

vent instead of spout.

• Outlet tube is blocked. • Check that outlet tube is not kinked, twisted

or pinched.

• Unscrew spout end piece and clean out any debris.

Water is dripping from

the spout/vent

intermittently.

• The expansion chamber isn’t

draining properly due to low

water pressure.

• The spout is blocked.

• Unplug the unit. If the dripping doesn’t stop after a

few minutes, check the supply valve to ensure that

is fully open and there are no obstructions in the

water line reducing the pressure below 30 psi (i.e.,

a poorly mounted saddle valve, a clogged water

filter, or a partially opened shut-off valve).

• Unscrew spout end piece and clean out any debris.

Water is dripping

from the spout/vent

constantly.

• Debris in the water line may

be in the faucet valve seat

causing a slow water leak.

• Unscrew spout end piece and clean out any debris.

• Activate faucet lever 7-10 times to flush faucet & lines.

Divided stream.

• Debris in the end piece. • Unscrew spout end piece and clean out any debris.

Water continues to run

after releasing lever.

(View/Wave)

• Mounting nut too tight.

• Mounting washers not

installed properly

• Loosen mounting nut, 1/4 turn at a time, until

shut-off occurs.

• See page 6, Step 2B to check proper mounting

washer installation.

PROBLEM POSSIBLE CAUSE

If you are still experiencing trouble call the AnswerLine

1-800-558-5700.

Please read Troubleshooting Guide and/or visit

www.insinkerator.com before calling AnswerLine

Water discoloration/

rusty appearance.

• Corrosion of unit. • Unplug and drain unit as described in the Seasonal

Storage/Drainage Section on page 12 of this

manual. If the water discoloration remains after

draining and refilling unit, discontinue use and

contact an authorized InSinkErator service agent.

Page is loading ...

InSinkErator H-VIEWSN-SS User manual

Brand: InSinkErator

Model: H-VIEWSN-SS

Category: Water dispensers

Type: User manual

Download PDF

report

in other languages

français: InSinkErator H-VIEWSN-SS Manuel utilisateur
español: InSinkErator H-VIEWSN-SS Manual de usuario

InSinkErator H-VIEWSN-SS User manual

InSinkErator H-VIEWSN-SS User manual

in other languages

Related papers

Other documents