Genius BRAIN 07 BRAIN 08 Operating instructions

Brand: Genius

Model: BRAIN 07 BRAIN 08

Category: Gate Opener

Type: Operating instructions

BRAIN 07BRAIN 07

24V / 230V24V / 230V

BRAIN 08

BRAIN 08BRAIN 08

24V / 115V24V / 115V

ISTRUZIONI PER L’USO - NORME DI INSTALLAZIONE

INSTRUCTIONS FOR USE - DIRECTIONS FOR INSTALLATION

INSTRUCTIONS - REGLES D’INSTALLATION

INSTRUCCIONES PARA EL USO - NORMAS PARA LA INSTALACION

GEBRAUCHSANLEITUNG - ANWEISUNGEN ZUR INSTALLATION

GEBRUIKSAANWIJZINGEN – INSTALLATIEVOORSCHRIFTEN

AVVERTENZE PER L’INSTALLATORE

OBBLIGHI GENERALI PER LA SICUREZZA

1) ATTENZIONE! È importante per la sicurezza delle persone seguire attentamente

tutta l’istruzione. Una errata installazione o un errato uso del prodotto può

portare a gravi danni alle persone.

2) Leggere attentamente le istruzioni prima di iniziare l’installazione del pro-

dotto.

3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati

alla portata dei bambini in quanto potenziali fonti di pericolo.

4) Conservare le istruzioni per riferimenti futuri.

5) Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo

indicato in questa documentazione. Qualsiasi altro utilizzo non espressamente

indicato potrebbe pregiudicare l’integrità del prodotto e/o rappresentare

fonte di pericolo.

6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso

da quello per cui l’automatismo è destinato.

7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi

infiammabili costituisce un grave pericolo per la sicurezza.

8) Gli elementi costruttivi meccanici devono essere in accordo con quanto

stabilito dalle Norme EN 12604 e EN 12605.

Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un livello di

sicurezza adeguato, devono essere seguite le Norme sopra riportate.

9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella

costruzione delle chiusure da motorizzare, nonché delle deformazioni che

dovessero intervenire nell’utilizzo.

10) L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453 e

EN 12445. Il livello di sicurezza dell’automazione deve essere C+D.

11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione

elettrica e scollegare le batterie.

12) Prevedere sulla rete di alimentazione dell’automazione un interruttore onnipo-

lare con distanza d’apertura dei contatti uguale o superiore a 3 mm. È consi-

gliabile l’uso di un magnetotermico da 6A con interruzione onnipolare.

13) Verificare che a monte dell’impianto vi sia un interruttore differenziale con

soglia da 0,03 A.

14) Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi le

parti metalliche della chiusura.

15) L’automazione dispone di una sicurezza intrinseca antischiacciamento costi-

tuita da un controllo di coppia. E’ comunque necessario verificarne la sogli di

intervento secondo quanto previsto dalle Norme indicate al punto 10.

16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali

aree di pericolo da Rischi meccanici di movimento, come ad Es. schiaccia-

mento, convogliamento, cesoiamento.

17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa

nonché di un cartello di segnalazione fissato adeguatamente sulla struttura

dell’infisso, oltre ai dispositivi citati al punto “16”.

18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funziona-

mento dell’automazione, in caso vengano utilizzati componenti dell’impianto

non di produzione GENIUS.

19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS.

20) Non eseguire alcuna modifica sui componenti facenti parte del sistema

d’automazione.

21) L’installatore deve fornire tutte le informazioni relative al funzionamento ma-

nuale del sistema in caso di emergenza e consegnare all’Utente utilizzatore

dell’impianto il libretto d’avvertenze allegato al prodotto.

22) Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto

durante il funzionamento.

23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro

datore di impulso, per evitare che l’automazione possa essere azionata

involontariamente.

24) Il transito tra le ante deve avvenire solo a cancello completamente aperto.

25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o

d’intervento diretto e rivolgersi solo a personale qualificato.

26) Tutto quello che non è previsto espressamente in queste istruzioni non è

permesso

IMPORTANT NOTICE FOR THE INSTALLER

GENERAL SAFETY REGULATIONS

1) ATTENTION! To ensure the safety of people, it is important that you read all the

following instructions. Incorrect installation or incorrect use of the product

could cause serious harm to people.

2) Carefully read the instructions before beginning to install the product.

3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of

children as such materials are potential sources of danger.

4) Store these instructions for future reference.

5) This product was designed and built strictly for the use indicated in this docu-

mentation. Any other use, not expressly indicated here, could compromise the

good condition/operation of the product and/or be a source of danger.

6) GENIUS declines all liability caused by improper use or use other than that for

which the automated system was intended.

7) Do not install the equipment in an explosive atmosphere: the presence of

inflammable gas or fumes is a serious danger to safety.

8) The mechanical parts must conform to the provisions of Standards EN 12604

and EN 12605.

For non-EU countries, to obtain an adequate level of safety, the Standards mentio-

ned above must be observed, in addition to national legal regulations.

9) GENIUS is not responsible for failure to observe Good Technique in the con-

struction of the closing elements to be motorised, or for any deformation

that may occur during use.

10) The installation must conform to Standards EN 12453 and EN 12445. The safety

level of the automated system must be C+D.

11) Before attempting any job on the system, cut out electrical power and

disconnect the batteries.

12) The mains power supply of the automated system must be fitted with an all-

pole switch with contact opening distance of 3mm or greater. Use of a 6A

thermal breaker with all-pole circuit break is recommended.

13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream

of the system.

14) Make sure that the earthing system is perfectly constructed, and connect

metal parts of the means of the closure to it.

15) The automated system is supplied with an intrinsic anti-crushing safety device

consisting of a torque control. Nevertheless, its tripping threshold must be

checked as specified in the Standards indicated at point 10.

16) The safety devices (EN 12978 standard) protect any danger areas against

mechanical movement Risks, such as crushing, dragging, and shearing.

17) Use of at least one indicator-light is recommended for every system, as well

as a warning sign adequately secured to the frame structure, in addition to

the devices mentioned at point “16”.

18) GENIUS declines all liability as concerns safety and efficient operation of the au-

tomated system, if system components not produced by GENIUS are used.

19) For maintenance, strictly use original parts by GENIUS.

20) Do not in any way modify the components of the automated system.

21) The installer shall supply all information concerning manual operation of the

system in case of an emergency, and shall hand over to the user the warnings

handbook supplied with the product.

22) Do not allow children or adults to stay near the product while it is operating.

23) Keep remote controls or other pulse generators away from children, to prevent

the automated system from being activated involuntarily.

24) Transit through the leaves is allowed only when the gate is fully open.

25) The user must not attempt any kind of repair or direct action whatever and

contact qualified personnel only.

26) Anything not expressly specified in these instructions is not permitted.

CONSIGNES POUR L’INSTALLATEUR

RÈGLES DE SÉCURITÉ

1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la lettre

toutes les instructions. Une installation erronée ou un usage erroné du produit

peut entraîner de graves conséquences pour les personnes.

2) Lire attentivement les instructions avant d’installer le produit.

3) Les matériaux d’emballage (matière plastique, polystyrène, etc.) ne doivent

pas être laissés à la portée des enfants car ils constituent des sources po-

tentielles de danger.

4) Conserver les instructions pour les références futures.

5) Ce produit a été conçu et construit exclusivement pour l’usage indiqué dans

cette documentation. Toute autre utilisation non expressément indiquée

pourrait compromettre l’intégrité du produit et/ou représenter une source

de danger.

6) GENIUS décline toute responsabilité qui dériverait d’usage impropre ou différent

de celui auquel l’automatisme est destiné.

7) Ne pas installer l’appareil dans une atmosphère explosive: la présence de gaz

ou de fumées inflammables constitue un grave danger pour la sécurité.

8) Les composants mécaniques doivent répondre aux prescriptions des Normes

EN 12604 et EN 12605.

Pour les Pays extra-CEE, l’obtention d’un niveau de sécurité approprié exige non

seulement le respect des normes nationales, mais également le respect des

Normes susmentionnées.

9) GENIUS n’est pas responsable du non-respect de la Bonne Technique dans la

construction des fermetures à motoriser, ni des déformations qui pourraient

intervenir lors de l’utilisation.

10) L’installation doit être effectuée conformément aux Normes EN 12453 et EN

12445. Le niveau de sécurité de l’automatisme doit être C+D.

11) Couper l’alimentation électrique et déconnecter la batterie avant toute

intervention sur l’installation.

12) Prévoir, sur le secteur d’alimentation de l’automatisme, un interrupteur om-

nipolaire avec une distance d’ouverture des contacts égale ou supérieure

à 3 mm. On recommande d’utiliser un magnétothermique de 6A avec

interruption omnipolaire.

13) Vérifier qu’il y ait, en amont de l’installation, un interrupteur différentiel avec

un seuil de 0,03 A.

14) Vérifier que la mise à terre est réalisée selon les règles de l’art et y connecter

les pièces métalliques de la fermeture.

15) L’automatisme dispose d’une sécurité intrinsèque anti-écrasement, formée

d’un contrôle du couple. Il est toutefois nécessaire d’en vérifier le seuil d’inter-

vention suivant les prescriptions des Normes indiquées au point 10.

16) Les dispositifs de sécurité (norme EN 12978) permettent de protéger des zones

éventuellement dangereuses contre les Risques mécaniques du mouvement,

comme l’écrasement, l’acheminement, le cisaillement.

17) On recommande que toute installation soit doté au moins d’une signalisation

lumineuse, d’un panneau de signalisation fixé, de manière appropriée, sur la

structure de la fermeture, ainsi que des dispositifs cités au point “16”.

18) GENIUS décline toute responsabilité quant à la sécurité et au bon fonc-

tionnement de l’automatisme si les composants utilisés dans l’installation

n’appartiennent pas à la production GENIUS.

19) Utiliser exclusivement, pour l’entretien, des pièces GENIUS originales.

20) Ne jamais modifier les composants faisant partie du système d’automa-

tisme.

21) L’installateur doit fournir toutes les informations relatives au fonctionnement

manuel du système en cas d’urgence et remettre à l’Usager qui utilise l’instal-

lation les “Instructions pour l’Usager” fournies avec le produit.

22) Interdire aux enfants ou aux tiers de stationner près du produit durant le

fonctionnement.

23) Eloigner de la portée des enfants les radiocommandes ou tout autre

générateur d’impulsions, pour éviter tout actionnement involontaire de

l’automatisme.

24) Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est com-

plètement ouvert.

25) L’Usager qui utilise l’installation doit éviter toute tentative de réparation ou

d’intervention directe et s’adresser uniquement à un personnel qualifié.

26) Tout ce qui n’est pas prévu expressément dans ces instructions est interdit.

ADVERTENCIAS PARA EL INSTALADOR

REGLAS GENERALES PARA LA SEGURIDAD

1) ATENCION! Es sumamente importante para la seguridad de las personas seguir

atentamente las presentes instrucciones. Una instalación incorrecta o un uso

impropio del producto puede causar graves daños a las personas.

2) Lean detenidamente las instrucciones antes de instalar el producto.

3) Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al

alcance de los niños, ya que constituyen fuentes potenciales de peligro.

4) Guarden las instrucciones para futuras consultas.

5) Este producto ha sido proyectado y fabricado exclusivamente para la

utilización indicada en el presente manual. Cualquier uso diverso del

previsto podría perjudicar el funcionamiento del producto y/o representar

fuente de peligro.

6) GENIUS declina cualquier responsabilidad derivada de un uso impropio o

diverso del previsto.

ENGLISH

CE DECLARATION OF CONFORMITY

Notes on reading the instruction

Read this installation manual to the full before you begin installing the product.

The symbol

indicates notes that are important for the safety of persons and for the good condition of the

automated system.

The symbol

draws your attention to the notes on the characteristics and operation of the product.

Manufacturer:

GENIUS S.p.A.

Address

: Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALY

Declares that:

Control unit mod.

BRAIN 07 - BRAIN 08

• conforms to the essential safety requirements of the following EEC directives:

73/23/EEC and subsequent amendment 93/68/EEC.

89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC

Additional information:

This product underwent a test in a typical uniform configuration (all products manufactured by GENIUS S.p.A.).

Grassobbio, 01-03-2005

Managing Director

D. Gianantoni

INDEX

1. GENERAL CHARACTERISTICS page.12

2. TECHNICAL SPECIFICATIONS page.12

3. PREPARATIONS page.12

4. BOARD LAY-OUT page.13

5. CONNECTION LAY-OUT page.13

6. DESCRIPTION OF CONNECTIONS page.14

6.1. TERMINAL-BOARD CN1 page.14

6.2. TERMINAL-BOARD CN2 page.14

6.3. TERMINAL-BOARD CN3 page.14

6.4. TERMINAL-BOARD CN4 page.15

7. OPERATION OF RECEIVER BOARD page.15

7.1. SAVING THE CODE page.15

7.2. DELETING RADIO CODES page.15

8. OPERATION OF ELECTRONIC CLUTCH page.16

9. CONTROL LEDS page.16

10. ADJUSTING THE OPERATING PARAMETERS page.16

11. PROGRAMMING page.17

12. PROTECTIVE FUSES page.17

13. OPERATING LOGICS page.18

14. HOW TO SECURE THE BOARD page.20

ENGLISH

24 Vdc CONTROL UNIT FOR SWING LEAF GATES

1. GENERAL CHARACTERISTICS

The BRAIN control unit was designed to control the operation of gates with swing leaves, with one or two 24 Vdc

motors.

Thanks to its built-in electronic clutch device, it guarantees - if correctly installed - installation conforming to the safety

regulations in force.

Extremely simple programming of the main functions reduces installation time.

Thanks to the facility for connecting two buffer batteries (optional) and to the internal recharging circuit, any mains

power cuts can be overcome.

The waterproof enclosure is designed for housing the control unit, its transformer and any buffer batteries (optional),

and has the characteristics and dimensions indicated in the table below.

2. TECHNICAL SPECIFICATIONS

Supply voltage of transformer

115/230 V~ (+6 -10%) - 50/60 Hz.

Supply voltage of control unit

22 V~ (+6 -10%) - 50/60 Hz.

Absorbed power

3 W

Motor max. load

70 W

Accessories max. load

24Vdc 500mA

Flashing lamp max load

24Vdc 15W max.

Operating ambient temperature

-20°C +50°C

Protective fuses

Operating logics

Automatic / Stepped automatic / Manual / Stepped manual

Opening / closing time

Through self-learning during programming

Pause time

Through self-learning during programming

Thrust force

4 dip-switch adjustable levels

Deceleration

Opening and closing through self-learning

Terminal board inputs

Power supply 22V~ / Batteries power supply / Total opening / Pede-

strian opening / Safety devices / Stop / Antenna

Radio receiver

Integrated

Terminal board outputs

Power supply: accessories 24 Vdc / Motors 24 Vdc / Flashing lamp

24 Vdc / Electric lock 24 Vdc

Board dimensions

165 x125 mm.

Characteristics of 230V~ toroidal transformer

prim. 230V~ - sec. 22V~ / 120VA / dimens. Ø105 x 40 mm.

Characteristics of 115V~ toroidal transformer

prim. 115V~ - sec. 22V~ / 120VA / dimens. Ø105 x 40 mm.

Characteristics of optional batteries

12V - 4 Ah / dimens. 90 x 70 x 108 mm.

Characteristics of outdoor enclosure

305 x 225 x 125 mm. - IP55

Different output values can be obtained on the 24V~ voltage depending on the mains voltage value. Before

start-up, always check the transformer output voltage. It must not exceed 26V~ for both power feed values of

230V~ and 115V~. Voltage must be measured load free, i.e. with the transformer powered and disconnected

from the board.

3. PREPARATIONS

To ensure people’s safety, all warnings and instructions in this booklet must be carefully observed. Incorrect

installation or incorrect use of the product could cause serious harm to people.

Make sure there is an adequate differential switch upstream of the system as specified by current safety standards,

and install an omnipolar thermal breaker on the electrical power mains.

For the installation of power cables: use adequate rigid and/or flexible tubes, always separating low voltage cables

from cables at 230/115 V~. To prevent any interference whatever, use separate sheaths.

• Maximum length of power cables between control unit and motors must not exceed 10 m, using cables of

2.5mm² diameter.

• Make sure that the mechanical closing and opening stops are installed.

To secure the various components inside of the airtight enclosure, refer to paragraph 14.

CN4CN4

RESET

MEMO

DP1

DL3

DL2

DL4

DL1

ENGLISH

4. BOARD LAY-OUT

5. CONNECTION LAY-OUT

CN1

Terminal-board supplying power

to board / accessories

CN2

Outputs terminal-board

CN3

Inputs terminal-board

CN4

Antenna terminal-board

DP1

Dip-switches

Accessories fuse

Primary power fuse

DL1

Power LED

DL2

FSW LED

DL3

STOP LED

DL4

MEMO RX LED

Built-in receiver

Fig. 02

Fig. 01

ENGLISH

6. DESCRIPTION OF CONNECTIONS

6.1. TERMINAL-BOARD CN1

6.1.1. 22V~ POWER SUPPLY

Terminals “

VAC - VAC

”. Connect the transformer secondary circuit to this input with power supply of 24V~ 50/60Hz.

Mains power supply “ON” is signalled by the “

POWER

” LED located under the terminal-board.

6.1.2. BATTERIES

Terminals “

3/4

”. Connect the power cables of the buffer batteries (optional) to these terminals. The control unit is

designed to operate with two buffer batteries with the characteristics shown on the table in paragraph 2. During

normal operation, the control unit keeps the batteries charged - the batteries come into operation in the event of a

mains power cut.

• Power supply from batteries only should be considered an

EMERGENCY

situation. The number of possible

manoeuvres is linked to the quality of the batteries, the structure of the gate to be moved, how long ago the

power cut occurred, etc, etc.

• The two batteries must be connected to each other in series.

• Observe the polarity of the batteries.

6.1.3. ACCESSORIES

Terminals “

5/6

”. Connect the accessories power cables to these terminals.

• The maximum load of the accessories must not exceed 500mA.

• The output of these terminals is on direct power. When connecting the accessories, observe correct polari-

ty.

6.1.4. EARTH

Terminal “

”. Connect the control unit earthing line to this terminal.

• This connection is absolutely necessary to ensure a correctly operating control unit.

6.2. TERMINAL-BOARD CN2

6.2.1. MOTOR M1

Terminals “

7/8

”. For two-leaf installations, the motor installed on the leaf which opens first must be connected to these

terminals. The maximum load of the motor must not exceed 70W.

6.2.2. MOTOR M2

Terminals “

9/10

”. These terminals are used solely and exclusively in two-leaf applications. Connect, to these terminals,

the power cables of the motor of the leaf opening second. For single leaf applications, these terminals are not used.

6.2.3. ELECTRIC LOCK

Terminals “

11/12

”. Connect these terminals to the electric lock, if any, with 24 Vdc power supply. This output is active

for 1.5 seconds before the opening manoeuvre.

• For two-leaf installations, the electric lock must be fitted on the same leaf as that of motor M1.

6.2.4. FLASHING LAMP

Terminals “

12/13

”. The flashing lamp with 24Vdc max 15W power supply must be connected to these terminals.

Before every manoeuvre, the flashing lamp pre-flashes for 0.5 sec.

• We advise you to connect the flashing lamp before programming the board, because it indicates - by a

series of flashes - the different programming stages of both the control unit and the receiver.

• Use a steady beam flashing lamp; flashing is controlled by the control unit itself.

6.3. TERMINAL-BOARD CN3

6.3.1. OPEN A

Terminals “

14/18

”. Normally open contact. Connect, to these terminals, any pulse generator (e.g. push-button, selector,

etc..) which, by closing the contact, commands the gate to totally open or close. The operation of this input is defined

by Dip-switch 6 - see paragraph 10.

• If there are several pulse generators, they must be connected in parallel.

ENGLISH

6.3.2. OPEN B

Terminals “

15/18

”. Normally open contact. Connect, to these terminals, any pulse generator (e.g. push-button, selector,

etc..) which, by closing the contact, commands the gate to partially open. In single-leaf applications, partial opening

coincides with an opening of about 60% of the total memory-stored opening. In two-motor applications, partial opening

coincides with total opening of the leaf by motor M1.

• If a total opening pulse is generated during pedestrian opening, it will be saved by the control unit and

performed at the end of the pedestrian opening.

• If there are several pulse generators, they must be connected in parallel.

6.3.3. PHOTOCELLS

Terminals “

16/18

”. Normally closed contact. Connect, to these terminals, any safety device (photocell, edge, pressure

switch, etc..) which, by opening the contact, acts on gate motion. This input can be active only during the closing stage

or also during the opening stage, according to how dip-switch 7 is selected (see paragraph 10). For the behaviour of

safety devices, see paragraph 13 (operating logics). The status of this input is shown by “FSW” LED.

• If no safety device is connected, jumper-connect the inputs.

6.3.4. STOP

Terminals “

17/18

”. Normally closed contact. Connect, to these terminals, any safety device (push-button, pressure switch

etc.) which, by opening the contact, acts on gate motion, causing motion to reverse for 1 second before stopping

movement, by disabling all the automatic functions. The status of this input is signalled by the “STOP” LED.

• If no device is connected, jumper-connect the inputs.

• If there are several safety devices, they must be connected in series.

6.4. TERMINAL-BOARD CN4

6.4.1. ANTENNA

Terminals “

19/20

”. Connect the external antenna, if any, to these terminals. Connect the antenna signal to terminal

20; connect the cable shielding to terminal 19.

7. OPERATION OF RECEIVER BOARD

The BRAIN control unit has a built-in receiver board. It operates only with the appropriate remote-controls, and a dif-

ferent receiver board cannot be connected. For programming and deleting the radio channel, follow the instructions

below.

7.1. SAVING THE CODE

1- Power up the system.

2- Press and hold down the “

MEMO RX

” push-button. The flashing lamp and the “

MEMO RX

” LED light up on steady

beam and indicate entry to the saving stage.

3- On the remote-control, press the push-button for the channel you wish to save - the flashing lamp flashes to indicate

that the push-button has been saved.

4- Release the radio-control push-button and the “

MEMO RX

” push-button: the flashing lamp and the “

MEMO RX

” LED

go off and you have exited the saving mode.

5- To save the next remote-controls, repeat from point 2.

7.2. DELETING RADIO CODES

During the deleting stage, you can delete one channel only or all the saved codes.

7.2.1. DELETING A RADIO CODE

Procedure for deleting one radio code only:

1- Press and hold down the “

MEMO RX

” push-button: the flashing lamp and the “

MEMO RX

” LED light up on steady

beam

2- After 10 seconds, press (on the radio control) the push-button for the channel you wish to delete: the flashing lamp

flashes for 5 seconds.

3- Release the radio control push-button and the “

MEMO RX

” push-button on the control unit: the flashing lamp and

the “

MEMO RX

” LED go off.

7.2.2. DELETING ALL RADIO CODES

Procedure for deleting all the saved codes:

1- Press and hold down the “

MEMO RX

” push-button: the flashing lamp and the “

MEMO RX

” LED light up on steady

beam

2- After 30 seconds, press any push-button on the radio control: the flashing lamp flashes for 10 seconds.

3- Release the remote control push-button and the “

MEMO RX

” push-button on the control unit: the flashing lamp

and the “

MEMO RX

” LED go off.

ENGLISH

8. OPERATION OF ELECTRONIC CLUTCH

This control unit has an electronic clutch device based on the control of the current absorbed by each motor. This

device is extremely important for safety. Its setting is maintained correct long-term and does not require maintenance

of further adjustments. This device is active during both closing and opening. When it operates, it reverses gate move-

ment without disabling automatic closing if enabled.

The electronic clutch can be adjusted over four sensitivity levels, by using the relevant dip-switches (see paragraph

10).

If the clutch operates two consecutive times, the control unit goes into “

STOP

” status, disabling all enabled automatic

functions. This is because, when the clutch operates twice consecutively, it means that the obstacle is still present

and it could be dangerous to perform another manoeuvre. When the obstacle has been removed, you must give an

“

OPEN

” command to resume the saved cycle.

If the clutch operates three consecutive times, and for more than 120 seconds, the control unit performs an “

EMER-

GENCY

” procedure: i.e. it executes complete opening until the opening mechanical stop-point is reached, and then

closes, if automatic closing has been enabled. With this manoeuvre, the control unit automatically re-calculates the

opening and closing stop-points.

• The “

EMERGENCY

”

procedure is carried out in slow mode.

9. CONTROL LEDS

There are 4 LEDs on the control unit for controlling inputs and the status of power supplied to the board. The behaviour

of the LEDs is described on the following table.

The statuses of the LEDs with control unit powered and gate closed are highlighted in bold.

LED

OFF

DL1

Mains power ON

No mains power / battery power

DL2

Safety devices released, contact closed

Safety devices engaged / contact open

DL3

Stop command released, contact closed

Stop command engaged, contact open

DL4

Saving mode enabled

Saving mode disabled

10. ADJUSTING THE OPERATING PARAMETERS

The control unit has 8 dip-switches for adjusting operating parameters. The operation of every dip-switch is described

in the table below.

To avoid damaging the control unit, the dip-switches must be set when the control unit is OFF. The only exception

to this is dip-switch 8 for access to programming.

ELECTRONIC CLUTCH

Sensitivity

Dip-switch 1

Dip-switch 2

Minimum force / maximum sensitivity

OFF

Medium-Low force / medium-high sensitivity

OFF

Medium-High force / medium-low sensitivity

OFF

Maximum force / minimum sensitivity

OPERATION OPEN A PUSH-BUTTON

OFF

Opens/Closes/Opens...

Opens/Stops/Closes/Stops/

Opens..

LEAF DELAY

OFF

Leaf delay 1.5 seconds

Leaf delay 3 seconds

INSTALLATION

OFF

Single-leaf installation

Two-leaf installation

AUTOMATIC CLOSURE

OFF

Automatic closure disabled

Automatic closure enabled

OPERATION OF FSW INPUT

OFF

Active only for closing

Active both for opening and closing

PROGRAMMING

OFF

Normal operation

Control unit in programming

mode

ENGLISH

11. PROGRAMMING

The work cycle is programmed entirely in self-learning mode. When the operation parameters have been adjusted,

follow the programming instructions below:

1- Release the motor/s, manually open the leaves up to half the required extent of opening, and re-lock the motor/s.

2- Power up the control unit and check if the LEDs are in the situation shown in paragraph 9.

3- Turn

dip-switch 8

- the flashing lamp goes on at steady beam to indicate you are in programming stage.

4- Give an opening pulse with one of the connected pulse generators or with the radio-control if already saved. The

first manoeuvre the gate performs must be the closure of the leaf/leaves. For two-leaf installations, the first leaf to

move must be the one on which motor M2 is installed. If this does not happen,

the control unit must be stopped operating by doing a “

RESET

”, using the

appropriate PIN, as indicated in Fig. 03. Exchange the wires of the motor/s

which did not perform the correct manoeuvre and repeat from point 1.

Remember to re-locate the “

RESET

” PIN in its initial position.

5- When the mechanical closure stop-point has been reached, the leaf/leaves

pause for about 2 seconds - when this time has elapsed, the opening manoe-

uvre begins. For 2-motor installations, the leaf with motor M1 moves first.

6- When the opening mechanical stop-point has been reached, the pause

time count begins.

7- When the required time has elapsed, supply another OPEN pulse, and the

gate will begin to close.

8- When the closure mechanical stop-point has been reached, programming has finished.

9- Turn

OFF dip-switch 8

: the flashing lamp goes off and programming has finished.

12. PROTECTIVE FUSES

The control unit has two protective fuses, one for the power supply to the accessories, and the other for the board

circuits. The fuse characteristics are indicated in the table below.

FUSE

CHARACTERISTICS

FUSE

CHARACTERISTICS

Power supply to accessories 5x20 T1.6A 250V

Primary power supply 5x20 T10A 250V

Fig. 03

ENGLISH

13. OPERATING LOGICS

Automatic logic (Dip-switch 3=OFF Dip-switch 6=ON)

Gate status

Pulses

Open A

Open B

Stop

Closure safety device

Dip-switch 5 ON

Dip-switch 5 OFF

Dip-switch 7 ON

Dip-switch 7 OFF

Closed

Opens gate and closes

after pause time

Opens leaf 1 and closes

after pause time

Partial opening: ~60% of

saved opening and closes

after pause time

Disables Open commands

Disables Open com-

mands

Open in pause

Closes immediately

Stops operation

Stops operation and, on

release, closes after 5 sec,

if pause time has elapsed

Stops operation and,

on release, closes after

5 sec, if pause time has

elapsed

Closing

Reverses gate movement

No effect

Stops operation

Stops operation and rever-

ses after release

Reverses gate movement

Opening

No effect

Stops operation

Stops operation and

restarts after release

No effect

Automatic Stepped logic (Dip-switch 3=ON Dip-switch6=ON)

Gate status

Pulses

Open A

Open B

Stop

Closure safety device

Dip-switch 5 ON

Dip-switch 5 OFF

Dip-switch 7 ON

Dip-switch 7 OFF

Closed

Opens gate and closes

after pause time

Opens leaf 1 and closes

after pause time

Partial opening: ~60% of

saved opening

Disables Open commands

Disables Open com-

mands

Open in pause

Closes immediately

Stops operation

Stops operation and, on

release, closes after 5 sec,

if pause time has elapsed

Stops operation and,

on release, closes after

5 sec, if pause time has

elapsed

Closing

Stops the gate movement,

opens at successive pulse

No effect

Stops operation

Stops operation and rever-

ses after release

Reverses gate movement

Opening

Stops the gate movement,

closes at successive pulse

No effect

Stops operation

Stops operation and

restarts after release

No effect

ENGLISH

Manual logic (Dip-switch 3=OFF Dip-switch6=OFF)

Gate status

Pulses

Open A

Open B

Stop

Closure safety device

Dip-switch 5 ON

Dip-switch 5 OFF

Dip-switch 7 ON

Dip-switch 7 OFF

Closed

Opens gate

Opens leaf 1

Partial opening: ~60% of

saved opening

Disables Open com-

mands

Disables Open com-

mands

Disables Open com-

mands

Open

Closes gate

Disables Open com-

mands

Disables OPEN command.

Disables OPEN com-

mand.

Closing

Reverses gate movement

No effect

Stops operation

Stops operation and

reverses after release

Reverses gate move-

ment

Opening

Reverses gate movement

No effect

Stops operation

Stops operation and

restarts after release

No effect

Manual Stepped logic (Dip-switch 3=ON Dip-switch6=OFF)

Gate status

Pulses

Open A

Open B

Stop

Closure safety device

Dip-switch 5 ON

Dip-switch 5 OFF

Dip-switch 7 ON

Dip-switch 7 OFF

Closed

Opens gate

Opens leaf 1

Partial opening: ~60% of

saved opening

Disables Open com-

mands

Disables Open com-

mands

Disables Open com-

mands

Open

Closes gate

Disables Open com-

mands

Disables OPEN command.

Disables OPEN com-

mand.

Closing

Stops the gate move-

ment, opens at successi-

ve pulse

No effect

Stops operation

Stops operation and

reverses after release

Reverses gate move-

ment

Opening

Stops the gate move-

ment, closes at successi-

ve pulse

No effect

Stops operation

Stops operation and

restarts after release

No effect

ENGLISH

14. HOW TO SECURE THE BOARD

The outdoor enclosure is designed to house the control unit, the toroidal transformer

and any buffer batteries (Optional).

To secure the toroidal transformer and the board support, consult the specific instruc-

tions.

To secure the control board, follow the instructions below:

1. Position the supplied spacers (Fig.04 ref.



) on the columns identified by the following

letters:

C-I-O-P-Q-G

2. Secure the board using the supplied screws (Fig.04 ref.



The spacers positioned next to letters

O & P

serve only for supporting the board.

3. Wire up according to the connection lay-out (paragraph 13).

4. To position and wire the battery kit, refer to the relevant instructions.

If you are using the battery kit, you MUST clear the pre-perforated hole in the lower

part of the enclosure (Fig.05 ref.



) as requested by current safety laws.

) as requested by current safety laws.

Fig. 04

Fig. 05

Page is loading ...

Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’ap-

parecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti

per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale.

The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils leaving the main features of the equip-

ments unaltered, to undertake any modifications to holds necessary for either technical or commercial reasons, at any time and without revising the present

publication.

Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter à tout moment les modifications qu’elle

jugera utiles sur ce produit tout en conservant les caractéristiques essentielles, sans devoir pour autant mettre à jour cette publication .

Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el derecho, dejando inmutadas las características

esenciales de los aparatos, de aportar, en cualquier momento y sin comprometerse a poner al día la presente publicación, todas las modificaciones que

considere oportunas para el perfeccionamiento técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial.

Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht vor, ohne die wesentlichen Eigenschaften

dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezung auf die Neufassung der vorliegenden Anleitungen, technisch bzw, konstruktiv / kommerziell

bedingte Verbesserungen vorzunehmen.

De beschrijvingen in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor op elk willekeurig moment de veranderingen aan te brengen

die het bedrijf nuttig acht met het oog op technische verbeteringen of alle mogelijke andere productie- of commerciële eisen, waarbij de fundamentele

eigenschappen van het apparaat gehandhaafd blijven, zonder zich daardoor te verplichten deze publicatie bij te werken.

GENIUS S.p.A.

Via Padre Elzi, 32

24050 - Grassobbio

BERGAMO-ITALY

tel. 0039.035.4242511

fax. 0039.035.4242600

[email protected]

www.geniusg.com