Neato Robotics 945-0292 User guide

Page is loading ...

1 REMOVE FILMS AND STICKERS

IMPORTANT: Remove all protective ﬁlms and shipping material from

the robot and charge base. If they are not removed, your Neato robot

will not operate correctly.

2 SET UP CHARGE BASE

Plug the power cord

securely into the

charge base.

Adjust the length of

the cord by wrapping it as shown.

3 INITIAL ROBOT CHARGING

Place the rounded side

of your Neato robot

against the metal

charging contacts on

the charge base until

the contacts are

pushed all of the way in.

For best results, charge the robot fully before your ﬁrst cleaning

cycle to experience a full high performance cleaning.

NOTE: During bootup, the robot LEDs next to the Start Button will

alternatively blink blue and green.

NOTE: Your robot is only compatible with the included charge base.

4 Get your • Smartphone / Tablet

• 2.4 GHz or 5 GHz Wi-Fi name & password

5 Download the Neato app

6 Open the Neato app and create a Neato account

7 Click Link in email to verify your email address

8 Follow steps in the Neato app to Add a new robot

Choose a wall outlet that has a 3’ (1 m)

clearance on both sides and in front

of the charge base. This helps your

robot ﬁnd the charge base.

Plug in the power cord and push

the charge base against the wall.

TIP: Locate the charge base on a hard ﬂoor surface.

TIP: Make sure the power outlet is not controlled by a switch.

Charging Contacts

Connecting Your Robot

ENGLISH

Use Neato FloorPlanner to add “No-Go” Lines.

See page 9 of the User Guide.

LED COLOR WHAT IT MEANS

Soft Glowing Blue

Robot is in Pairing Mode

Fast Blinking Blue*

Pairing to Neato app/account

Fast Blinking Red

Error Connecting

Solid Blue

Pairing Successful

No Light Robot Oine – please connect to access additional features

WI-FI LED

START BUTTON, HOUSE CLEAN and SPOT CLEAN LEDs

*If you’ve already paired, Fast Blinking Blue means the robot has lost connection. The robot could be

out of range, your Wi-Fi network may be down, or another Wi-Fi issue maybe have occurred. If out of

range, the robot will automatically reconnect when it comes back within range. Otherwise, check your

router to make sure it’s operating normally.

ACTION HOUSE CLEAN LED SPOT CLEAN LED

Start

Cleaning

Press Start Button 1x for

house cleaning

Solid Blue

Press Start Button 2x for

spot cleaning

Solid Blue

Pause/

Resume

Cleaning

Press Start Button during

cleaning to pause robot.

Pulses while paused

in House Clean

Pulses while paused in

Spot Clean

Press Start Button again

to resume cleaning

Solid Blue Solid Blue

Cancel

Cleaning

(When

Paused)

Press & hold Start Button

for 5 seconds to cancel

cleaning

Robot & LEDs turn

o & robot plays a

tone

Robot & LEDs turn o

& robot plays a tone

* NOTE: if LED light is blinking red or solid red, your robot needs robot maintenance or

your robot has a navigation issue. Please check the troubleshooting section of this guide.

During pairing the WI-FI LED will change based on connection status: Use the Neato app to start using your robot,

or press the Start Button on the robot.

If you don’t connect within the ﬁrst 60 minutes of charging your

robot OR if the robot does not connect the ﬁrst time, please do the

following:

• Press and hold the Start Button

and Right Bumper for

15 seconds to turn robot o.

• Press the Start Button again to turn robot on. The WI-FI LED

is slow blinking blue and robot is in pairing mode.

• Follow steps in the Neato app to Add a new robot.

Start

Button

Right

Side

Bumper

Pairing Issues - Try Again Start Using Your Robot

Need Assistance?

Watch How–To Video here

www.NeatoRobotics.com/connect

Call 1-877-296-3286 or go to

www.NeatoRobotics.com/support

for a contact phone number in your area

Email CustomerCare@NeatoRobotics.com

ENGLISH

Page is loading ...

Neato Robotics, Inc.

8100 Jarvis Avenue, Newark, CA 94560 USA

NeatoRobotics.com

515-0057 Rev 2

Neato Robotics 945-0292, 48235 User guide

Related papers

Other documents