Whirlpool HIN 150 IX Owner's manual

OVEN

HI 150.B

HI 150.B IX

HI 20.B

HI 20.A IX

HIN 150

HIN 150 IX

HI 20.A

Contents

Installation, 2-4

Positioning

Electrical connections

Data plate

Description of the appliance, 5

Overall view

Control panel

Start-up and use, 6

Starting the oven

Using the cooking timer

Cooking modes, 7-8

Cooking modes

Practical cooking advice

Cooking advice table

Hob, 9

Type of hob

Switching on the glass ceramic hob

Practical advice on using the glass ceramic hob

Precautions and tips, 10

General safety

Disposal

Respecting and conserving the environment

Maintenance and care, 11

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

Assistance

Operating Instructions

GB

Nederlands, 23English,1

Deutsch, 34 ÅëëçíéêÜ, 45

Français, 12

FR

GB

NL

DE GR

Espanol, 56

ES

2

GB

 Before placing your new appliance into operation

please read these operating instructions carefully.

They contain important information for safe use, for

installation and for care of the appliance.

 Please keep these operating instructions for future

reference. Pass them on to possible new owners of

the appliance.

Positioning

 Keep packaging material out of the reach of

children.It can become a choking or suffocation

hazard (see Precautions and tips).

 The appliance must be installed by a qualified

person in compliance with the instructions provided.

Incorrect installation may cause harm to persons,

animals or may damage property.

Fitting the appliance

Use the appropriate cabinet to ensure that the

appliance functions properly.

 The panels adjacent to the oven must be made of

heat-resistant material.

 Cabinets with a veneer exterior must be assembled

with glues which can withstand temperatures of up

to 100°C.

 To install the oven under the counter (see

diagram) and in a kitchen unit, the cabinet must

have the following dimensions:

 The appliance must not come into contact with

electrical parts once it has been installed.

The consumption indications on the data plate have

been calculated for this type of installation.

Ventilation

To ensure good ventilation, the back panel of the

cabinet must be removed. It is advisable to install the

oven so that it rests on two strips of wood, or on a

completely flat surface with an opening of at least 45 x

560 mm (see diagrams).

Centring and fastening

Position the 4 tabs on the side of the oven according

to the 4 holes of the outer frame. Adjust the tabs

according to the thickness of the cabinet side panel,

as shown below:

thickness of 20 mm: take off

the removable part of the tab

(see diagram)

thickness of 18 mm: use the

first groove, which has already

been set in the factory (see

diagram)

thickness of 16 mm: use the

second groove (see diagram)

Secure the appliance to the cabinet by opening the

oven door and putting 4 screws into the 4 holes of the

outer frame.

 All parts which ensure the safe operation of the

appliance must not be removable without the aid of a

tool.

595

558

min

45

min

575-585 min

560

+4 -0

480

+4 -0

547 min

555

580

500

39

15

595

23

572

543

545

560 m

m

.

45 mm.

Installation

3

GB

Electrical connections

The cooker must be connected to the mains electricity

supply. It is designed to operate with alternating

current at the voltage and frequency indicated on the

data plate (see the following page).

The hob is connected to the cooker using a special

connector.

BUILT-IN HOB

BUILT-IN COOKER

WHITE RED

YELLOW

BLUE GREEN

Only on

certain models

Replace the metal protection after performing all the

necessary hob connections. If the hob is removed

from its position, the red cap which was originally

protecting the red connector must be replaced.

Fitting the power supply cable

1. Open the terminal

board by inserting a

screwdriver into the side

tabs of the cover. Use

the screwdriver as a

lever by pushing it down

to open the cover (see

diagram).

2. Install the power supply cable by loosening the

cable clamp screw and the wire contact screws L-N-

. Connect the wires to the corresponding terminals:

the Blue wire to the terminal marked (N), the Brown

wire to the terminal marked (L) and the Yellow Green

wire to the terminal marked

.

The terminal board is designed for a 400 V three-

phase connection (see diagrams below).

400V 3N~H05RR-F

5x2.5 CEI-UNEL 35363

If the electrical system has other characteristics (see

diagrams below), carry out the electrical connection

using the connection supports provided in the box P.

230V ~H05RR-F 3x4

CEI-UNEL 35363

400V 2N~H05RR-F 4x4

CEI-UNEL 35363

3. Secure the power supply cable by fastening the

clamp screw.

4. Close the cover of the terminal board.

NL1L3L2

1

3

2

4

5

N

L2

L1

L3

P

NL

1

3

2

4

5

NL1L2

1

3

2

4

5

4

GB

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (see side).

The appliance must be directly connected to the

mains using an omnipolar circuit-breaker with a

minimum contact opening of 3 mm installed between

the appliance and the mains, suitable for the load

indicated and complying with current electrical

regulations (the earthing wire must not be interrupted

by the circuit-breaker). The supply cable must not

come into contact with surfaces with temperatures

higher than 50°C.

 The installer must ensure that the correct electrical

connection has been made and that it is compliant

with safety regulations.

Before connecting to the power supply, make sure that:

 The appliance is earthed and the plug is compliant

with the law.

 The socket can withstand the maximum power of

the appliance, which is indicated on the data plate

(see below).

 The voltage must be in the range between the

values indicated on the data plate (see below).

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

 Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

 The cable must not be bent or compressed.

 The cable must be checked regularly and replaced

by authorised technicians only (see Assistance).

 The manufacturer declines any liability should

these safety measures not be observed.

DATA PLATE

Dimensions

width 43.5 cm

height 32 cm

depth 43,5 cm

Volume

lt. 60

Electrical

connections

voltage: 230V/400V~ 3N 50/60Hz

maximum power absorbed 8400W

ENERGY LABEL

Directive 2002/40/EC on the label

of electric ovens.

Standard EN 50304

Energy consumption Class

certification Natural convection

heating mode: TRADITIONAL

This appliance conforms to the

following European Economic

Community directives:

2006/95/EEC of 12/12/06 (Low

Voltage) and subsequent

amendments;

- 2004/108/EEC of 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments;

- 93/68/EEC of 22/07/93 and

subsequent amendments.

- 2002/96/EC and subsequent

amendments.

5

GB

Control panel

GRILL rack

DRIPPING PAN

GUIDES for the

sliding racks

position 5

position 4

position 3

position 2

position 1

Description of the

appliance

Overall view

Control panel

SELECTOR

Knob

HOTPLATES

knob

HOTPLATES

indicator light

6

GB

 The first time you use your appliance, heat the

empty oven with its door closed at its maximum

temperature for at least half an hour. Ensure that the

room is well ventilated before switching the oven off

and opening the oven door. The appliance may

produce a slightly unpleasant odour caused by the

burning away of protective substances used during

the manufacturing process.

Starting the oven

1. Select the desired cooking mode by turning the

SELECTOR knob.

2. See the Cooking advice table for cooking modes

and the suggested cooking temperatures (see

Cooking Modes).

3. You may do the following during cooking:

- change the cooking mode by turning the SELECTOR

knob

- stop cooking by turning the SELECTOR knob to the

0 position

 Never put objects directly on the oven bottom to

avoid damaging the enamel coating.

 Always place cookware on the rack(s) provided.

Oven light

When selecting

with the SELECTOR knob the

oven light goes on. It remains on when a cooking

mode is selected.

Start-up and use

7

GB

Cooking modes

TRADITIONAL OVEN mode

Both the top and bottom heating elements will come

on. With this traditional cooking mode, it is best to use

one cooking rack only; if more than one rack is used,

the heat will be distributed unevenly.

The oven will automatically reach the temperature set,

and the thermostat, which is controlled by the

SELECTOR knob, will keep it constant.

TOP OVEN mode

The top heating element comes on. This mode can be

used to brown food at the end of cooking. Always

cook in this mode with the oven door closed.

Cooking modes

Practical cooking advice

 In the GRILL cooking mode, place the dripping pan

in position 1 to collect cooking residues (fat and/or

grease).

GRILL

 Insert the rack in position 3 or 4. Place the food in

the centre of the rack.

 The top heating element is regulated by a

thermostat and may not always be on.

PIZZA

 Use a light aluminium pizza pan. Place it on the

rack provided.

For a crispy crust, do not use the dripping pan

(prevents crust from forming by extending cooking

time).

 If the pizza has a lot of toppings, we recommend

adding the mozzarella cheese on top of the pizza

halfway through the cooking process.

8

GB

Cooking advice table

Foods

Weight

(in kg)

Rack position

Pre-heating time

(min)

Recommended

temperature

Cooking time

(minutes)

2asta

Lasagne

Cannelloni

Tagliatelle

2.5

3

-

210

75-80

Meat

Veal

Chicken

Turkey

Duck

Rabbit

Pork

Lamb

1.7

1.5

3.0

1.8

2.0

2.1

1.8

3

-

220

220-Max

220

85-90

110-115

95-100

120-125

105-110

100-110

90-95

Fish

Mackerels

Dentex

Trout baked

in foil

1.1

1.5

1.0

3

-

210-230

55-60

60-65

40-45

2izza

Napolitan

1.0 3 15 Max 30-35

2ies

Biscuits

Tart

Chocolate cake

Leavened cake

0.5

1.1

1.0

3

15

180

200

30-35

45-50

50-55

9

GB

Hob

Type of hob

The oven is combined with a hob that can be made up of

two types of heating elements: cast-iron electric plates

(see diagram 1) or glass ceramic hobs (see diagram 2).

Switching on the glass ceramic hob

Traditional cooking zones

Traditional cooking zones are made up of circular

heating elements. They turn red approximately ten

seconds after they have been turned on.

Each cooking zone is fitted with a control knob allowing

you to select from 6 different temperature settings from a

minimum of 1 to a maximum of 6.

Residual heat indicator lights*

The indicator lights (C) indicate that the temperature of

the corresponding cooking zones have exceeded 60°C,

even after the heating element has been switched off.

Recommended power levels for various types of

cooking:

Setting Normal or Fast Plate

0

Off

1

Cooking vegetables, fish

2

Cooking potatoes (using steam) soups,

chickpeas, beans.

3

Continuing the cooking of large quantities

of food, minestrone

4

For roasting (average)

5

For roasting (above average)

6

For browning and reaching a boil in a

short time.

Practical advice on using the glass

ceramic hob

 The glue that is applied on the gaskets leaves some

traces of grease on the glass. Before using the

appliance, we recommend you eliminate these with a

special non-abrasive cleaning product. During the first

few hours of use there may be a smell of rubber which

will disappear very quickly.

To obtain the best results with your hob:

 Use flat-bottomed pans to ensure that they adhere to

the cooking zone perfectly.

 Always use pans with a diameter that is large enough

to cover the hotplate fully, in order to use all the

available heat.

 Make sure that the bottom of the cookware is always

dry and clean to guarantee correct adherence and

long life, not only for the cooking zones but also for

the cookware itself.

 Avoid using the same cookware that is used on gas

burners: the heat concentration on gas burners may

deform the base of

the pan, causing it not to adhere

correctly.

 Never leave a cooking zone on without cookware on it

because as it heats up and rapidly reaches the

maximum level, it could damage the heating

elements.

diagram 2

diagram 1

C

A

* Only on certain models

10

GB

Precautions and tips

 The appliance was designed and manufactured in

compliance with international safety standards. The

following warnings are provided for safety reasons

and must be read carefully.

General safety

 The appliance was designed for domestic use

inside the home and is not intended for

commercial or industrial use.

 The appliance must not be installed outdoors,

even in covered areas. It is extremely dangerous

to leave the appliance exposed to rain and

storms.

 When handling the appliance, always use the

handles provided on the sides of the oven.

 Do not touch the appliance with bare feet or with

wet or moist hands and feet.

 The appliance must be used to cook food by

adults only and according to the instructions in this

manual.

 Do not touch the heating elements and parts of

the oven door when the appliance is in use;

these parts become extremely hot. Keep

children well away from the appliance.

 Ensure that the power supply cable of other

electrical appliances does not come into contact

with the hot parts of the oven.

 The openings used for ventilation and dispersion

of heat must never be covered.

 Always grip the oven door handle in the centre:

the ends may be hot.

 Always use oven gloves to place cookware in the

oven or when removing it.

 Do not use aluminium foil to line the bottom of the

oven.

 Do not place flammable materials in the oven: if

the appliance is switched on by mistake, it could

catch fire.

 Always make sure the knobs are in the l/

¡

position when the appliance is not in use.

 When unplugging the appliance always pull the

plug from the mains socket, do not pull on the

cable.

 Never carry out any cleaning or maintenance work

without having unplugged the plug from the

mains.

 In the case of a malfunction, under no

circumstances should you attempt to repair the

appliance yourself. Repairs carried out by

inexperienced persons may cause injury or further

malfunctioning of the appliance. Contact a Service

Centre (see Assistance).

 Do not rest heavy objects on the open oven door.

 The glass ceramic hob is resistant to mechanical

shocks, but it may crack (or even break) if hit with

a sharp object such as a tool. If this happens,

disconnect the appliance from the electricity

mains immediately and contact a Service Centre.

 Remember that the temperature of the cooking

zones remains relatively high for at least thirty

minutes after they have been switched off.

 Keep any object that could melt away from the

hob, for example plastic and aluminium objects,

or products with a high sugar content. Keep

plastic or aluminium objects away from the hob: if

you forget them on surfaces that are still hot, they

may cause serious damage to the hob.

 The appliance should not be operated by people

(including children) with reduced physical,

sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with

the product. These individuals should, at the very

least, be supervised by someone who assumes

responsibility for their safety or receive

preliminary instructions relating to the operation of

the appliance.

 Do not let children play with the appliance.

Disposal

 Observe local environmental standards when

disposing packaging material for recycling

purposes. Observe existing legislation when

disposing of the old appliance.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE),

requires that old household electrical appliances

must not be disposed of in the normal unsorted

municipal waste stream. Old appliances must be

collected separately in order to optimise the

recovery and recycling of the materials they

contain and reduce the impact on human health

and the environment. The crossed out wheeled

bin symbol on the product reminds you of your

obligation, that when you dispose of the

appliance it must be separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Respecting and conserving the

environment

 By using the appliance in the hours between late

afternoon and early morning, you can help reduce

the work load placed on electrical companies.

 Always keep the oven door closed when using the

GRILL mode to attain best results and to save

energy (approximately 10%).

 Regularly check the door seals and wipe clean to

ensure they are free of debris so that they stick

properly to the door and do not allow heat to

disperse.

11

GB

Switching the appliance off

Disconnect your appliance from the electricity supply

before carrying out any work on it.

Cleaning the appliance

 The stainless-steel or enamel-coated external parts

as well as the rubber seals may be cleaned using a

sponge that has been soaked in lukewarm water

and neutral soap. If these stains are difficult to

remove, use only specialised products. After

cleaning, rinse and dry thoroughly. Do not use

abrasive powders or corrosive substances.

 Ideally, the inside of the oven should be cleaned

after each use, when it is still lukewarm. Use hot

water and detergent, rinse and dry with a soft cloth.

Do not use abrasive products.

 The accessories can be washed like everyday

crockery (even in your dishwasher).

 Never use steam cleaners or pressure cleaners on

the appliance.

Cleaning the oven door

Clean the glass part of the oven door using a sponge

and a non-abrasive cleaning product, then dry

thoroughly with a soft cloth. Do not use rough abrasive

material or sharp metal scrapers as these could

scratch the surface and cause the glass to crack.

To clean more thoroughly, you can remove the oven door.

1. Open the oven door fully

(see diagram).

2. lift up and turn the small

levers situated on the two

hinges; (see diagram).

3. Grip the door on the two

external sides and close it

approximately half way. Unlock

the door by pressing on the

clamps ., then pull the door

towards you lifting it out of its

seat (see diagram).

To replace the door, reverse this sequence.

Inspecting the seals

Check the door seals around the oven periodically. If

the seals are damaged, please contact your nearest

After-sales Service Centre (see Assistance). We

recommend not using the oven until the seals have

been replaced.

Replacing the light bulb

To replace the oven light bulb:

1. Remove the glass cover of the lamp-holder.

2. Remove the light bulb and replace it with a similar

one: Wattage 25 W, cap E 14.

3. Replace the glass cover (see diagram).

Assistance

Communicating:

 appliance model (Mod.)

 serial number (S/N)

This information is found on the data plate located on

the appliance and/or on the packaging.

F

Maintenance and care

Page is loading ...

Whirlpool HIN 150 IX Owner's manual

Whirlpool HIN 150 IX Owner's manual

in other languages

Related papers

Other documents