Makita LS1040 User manual

Compound Miter Saw

Instruction Manual

Gehrungs- und Kappsäge

Betriebsanleitung

Ukośnica

Instrukcja obsługi

Пила для составной отрезки

Инструкция по эксплуатации

LS1040

Page is loading ...

8

Symbols

The following show the symbols used for the tool. Be sure that you understand their meaning before use.

Symbole

Die folgenden Symbole werden für die Maschine verwendet. Machen Sie sich vor der Benutzung unbedingt

mit ihrer Bedeutung vertraut.

Symbole

Poniższe symbole używane są do opisu urządzenia. Przed użyciem należy upewnić się, że rozumie się ich

znaczenie.

Символы

Следующие объяснения показывают символы, используемые для инструмента. Убедитесь перед

использованием, что Вы понимаете их значение.

❏ Read instruction manual.

❏ Bitte Bedienungsanleitung lesen.

❏ Przeczytaj instrukcję obsługi.

❏ Прочитайте инструкцию по эксплуатации.

❏ DOUBLE INSULATION

❏ DOPPELT SCHUTZISOLIERT

❏ PODWÓJNA IZOLACJA

❏ ДВОЙНАЯ ИЗОЛЯЦИЯ

❏ Do not place hand or fingers close to the blade.

❏ Halten Sie Hände oder Finger vom Sägeblatt fern

❏ Nie zbliżaj rąk i palców do brzeszczotu.

❏ Не помещайте руки или пальцы близко к лезвию.

❏ To avoid injury from flying debris, keep holding the saw head down, after making cuts, until the

blade has come to a complete stop.

❏ Um Verletzungen durch herausgeschleuderte Teile zu vermeiden, halten Sie den Sägekopf nach

Ausführung von Schnitten abgesenkt, bis das Sägeblatt völlig zum Stillstand gekommen ist.

❏ Aby uniknąć zranienia odskakującymi odpadkami, po zakończeniu cięcia trzymaj głowicę piły w

dole, aż do całkowitego zatrzymania się brzeszczotu.

❏ Чтобы избежать травмы от летящих обрезков, удерживайте переднюю часть пилы,

обращенной вниз, после выполнения резки до тех пор, пока лезвие не остановится

полностью.

❏ For your safety, remove chips, small pieces, etc. from the table top before operation.

❏ Zur Sicherheit sollte die Tischplatte vor dem Betrieb von Spänen, Kleinteilen usw. gesäubert wer-

den.

❏ Dla bezpieczeństwa przed przystąpieniem do pracy usuń strużyny, małe odpady itp. z

powierzchni stołu.

❏ Для Вашей безопасности удалите стружки, маленькие куски и т.д. со стола перед

эксплуатацией.

❏ Always set SUB-FENCE to left position when performing left bevel cuts. Failure to do so may cause

serious injury to operator.

❏ Stellen Sie den ZUSATZANSCHLAG bei der Durchführung von Neigungsschnitten immer auf die

linke Position. Anderenfalls kann die Bedienungsperson ernsthaft verletzt werden.

❏ Podczas wykonywania cięć pod kątem pionowym lewym zawsze ustaw PROWADNICĘ po lewej

stronie. Niestosowanie się do tego zalecenia może doprowadzić do poważnego zranienia

operatora.

❏ При выполнении левых наклонных разрезов всегда устанавливайте ДОПОЛНИТЕЛЬНЫЙ

ЩИТОК в левое положение. Невыполнение этого условия может привести к серьезной

травме оператора.

9

ENGLISH

Explanation of general view

1Base

2Hex bolt

3 Auxiliary plate

4Nut

5Bolt

6Center cover

7 Socket wrench

8 Shaft lock

9Loosen

10 Arrow

11 Blade case

12 Arrow

13 Saw blade

14 Spindle

15 Flange

16 Ring

17 Flange

18 Hex bolt

19 Tighten

20 Safety cover

21 Dust spout

22 Dust bag

23 Fastener

24 Lock-off button

25 Switch trigger

26 Lever

27 Turn base

28 Kerf board

29 Sub-fence

30 Adjusting bolt

31 Pointer

32 Miter scale

33 Latch spring

34 Grip

35 Lever

36 Bevel scale

37 Pointer

38 Vise rod

39 Screws

40 Guide fence

41 Vise arm

42 Clamp screw

43 Support

44 Knob

45 Projection

46 Holder

47 Screw

48 Holder assembly

49 Screw

50 Rod 12

51 Cutting line

52 Groove

53 Vise

54 Spacer block

55 Aluminum extrusion

56 Spacer block

57 Over 10 mm

58 Over 460 mm

59 Hole

60 Set plate

61 Screw

62 Triangular rule

63 Hex bolts

64 Arm

65 Hex bolt (A)

66 Top surface of turn base

67 Arm holder

68 Hex bolt (B)

69 Limit mark

70 Screwdriver

71 Brush holder cap

SPECIFICATIONS

Model LS1040

Blade diameter .................................................................................................................................. 255 mm — 260 mm

Hole (arbor) diameter

For all countries other than European countries ........................................................................... 25.4 mm and 25 mm

For European countries ......................................................................................................................................30 mm

Max. cutting capacities (H x W) with blade 260 mm in diameter

No load speed (RPM) ............................................................................................................................................. 4,600

Dimensions (L x W x H) .....................................................................................................530 mm x 476 mm x 532 mm

Net weight ............................................................................................................................................................... 11 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for accurate straight and miter cut-

ting in wood. With appropriate saw blades, aluminum can

also be sawed.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

For public low-voltage distribution systems of

between 220 V and 250 V

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.30 Ohms it can be presumed that

there will be no negative effects. The mains socket used

for this device must be protected with a fuse or protective

circuit breaker having slow tripping characteristics.

Miter angle

Bevel angle

0° 45° (left and right)

0°

93 mmx 95 mm

69 mm x 135 mm

93 mmx 67 mm

69 mmx 95 mm

45° (left)

53 mmx 95 mm

35 mm x 135 mm

49 mmx 67 mm

35 mmx 94 mm

10

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety pre-

cautions should always be followed to reduce the

risk of fire, electric shock and personal injury, includ-

ing the following. Read all these instructions before

attempting to operate this product and save these

instructions.

For safe operation:

1. Keep work area clean

Cluttered areas and benches invite injuries.

2. Consider work area environment

Don’t expose power tools to rain. Don’t use power

tools in damp or wet locations. Keep work area well

lit. Don’t use power tools in presence of flammable

liquids or gases.

3. Guard against electric shock

Prevent body contact with grounded surfaces (e.g.

pipes, radiators, ranges, refrigerators).

4. Keep children away

Do not let visitors contact tool or extension cord. All

visitors should be kept away from work area.

5. Store idle tools

When not in use, tools should be stored in dry, high,

or locked-up place, out of the reach of children.

6. Don’t force tool

It will do the job better and safer at the rate for which

it was intended.

7. Use right tool

Don’t force small tools or attachments to do the job

of a heavy duty tool. Don’t use tools for purposes not

intended; for example, don’t use circular saw for cut-

ting tree limbs or logs.

8. Dress properly

Do not wear loose clothing or jewelry. They can be

caught in moving parts. Rubber gloves and non-skid

footwear are recommended when working outdoors.

Wear protective hair covering to contain long hair.

9. Use safety glasses and hearing protection

Also use face or dust mask if cutting operation is

dusty.

10. Connect dust extraction equipment

If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used.

11. Don’t abuse cord

Never carry tool by cord or yank it to disconnect it

from receptacle. Keep cord from heat, oil and sharp

edges.

12. Secure work

Use clamps or a vise to hold work. It’s safer than

using your hand and it frees both hands to ope-rate

tool.

13. Don’t overreach

Keep proper footing and balance at all times.

14. Maintain tools with care

Keep tools sharp and clean for better and safer per-

formance. Follow instructions for lubricating and

changing accessories. Inspect tool cords periodi-

cally and, if damaged, have repaired by authorized

service facility. Inspect extension cords periodically

and replace if damaged. Keep handles dry, clean

and free from oil and grease.

15. Disconnect tools

When not in use, before servicing, and when chang-

ing accessories such as blades, bits and cutters.

16. Remove adjusting keys and wrenches

Form the habit of checking to see that keys and

adjusting wrenches are removed from tool before

turning it on.

17. Avoid unintentional starting

Don’t carry plugged-in tool with finger on switch. Be

sure switch is off when plugging in.

18. Outdoor use extension cords

When tool is used outdoors, use only extension

cords intended for use outdoors and so marked.

19. Stay alert

Watch what you are doing. Use common sense. Do

not operate tool when you are tired.

20. Check damaged parts

Before further use of the tool, a guard or other part

that is damaged should be carefully checked to

determine that it will operate properly and perform

its intended function. Check for alignment of moving

parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect

its operation. A guard or other part that is damaged

should be properly repaired or replaced by an autho-

rized service center unless otherwise indicated else-

where in this instruction manual. Have defective

switches replaced by and authorized service center.

Do not use tool if switch does not turn it on and off.

21. Warning

The use of any other accessory or attachment other

than recommended in this operating instruction or

the catalog may present a risk of personal injury.

22. Have your tool repaired by an expert

This electric appliance is in accordance with the rel-

evant safety rules. Repairing of electric appliances

may be carried out only by experts otherwise it may

cause considerable danger for the user.

ADDITIONAL SAFETY RULES

1. Wear eye protection.

2. Do not operate saw without guards in place.

3. Don’t use the tool in the presence of flammable

liquids or gases.

4. Check the blade carefully for cracks or damage

before operation. Replace cracked or damaged

blade immediately.

5. Use only flanges specified for this tool.

11

6. Be careful not to damage the arbor, flanges

(especially the installing surface) or bolt. Dam-

age to these parts could result in blade break-

age.

7. Make sure that the turn base is properly secured

so it will not move during operation.

8. For your safety, remove the chips, small pieces,

etc. from the table top before operation.

9. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

10. Make sure the shaft lock is released before the

switch is turned on.

11. Be sure that the blade does not contact the turn

base in the lowest position.

12. Hold the handle firmly. Be aware that the saw

moves up or down slightly during start-up and

stopping.

13. Do not perform any operation freehand. The

workpiece must be secured firmly against the

turn base and guide fence with the vise during

all operations. Never use your hand to secure

the workpiece.

14. Keep hands out of path of saw blade. Avoid con-

tact with any coasting blade. It can still cause

severe injury.

15. Never reach around saw blade.

16. Make sure the blade is not contacting the work-

piece before the switch is turned on.

17. Before using the tool on an actual workpiece, let

it run for a while. Watch for vibration or wobbling

that could indicate poor installation or a poorly

balanced blade.

18. Wait until the blade attains full speed before cut-

ting.

19. Stop operation immediately if you notice any-

thing abnormal.

20. Do not attempt to lock the trigger in the ON posi-

tion.

21. Shut off power and wait for saw blade to stop

before servicing or adjusting tool.

22. Be alert at all times, especially during repetitive,

monotonous operations. Don’t be lulled into a

false sense of security. Blades are extremely

unforgiving.

23. Always use accessories recommended in this

manual. Use of improper accessories such as

abrasive wheels may cause an injury.

24. Don’t abuse cord. Never yank cord to disconnect

it from the receptacle. Keep cord away from heat,

oil, water and sharp edges.

25. Do not use the saw to cut other than aluminum,

wood or similar materials.

26. Connect compound miter saws to a dust collect-

ing device when sawing.

27. Select saw blades in relation to the material to be

cut.

28. Take care when slotting.

29. Replace the kerf board when worn.

SAVE THESE INSTRUCTIONS.

OPERATCING INSTRUCTIONS

Carrying tool (Fig. 1)

When carrying the tool, lower the handle fully and press

the stopper pin to lock the handle in the lowered position.

Secure the turn base by means of the grip. The tool can

then be conveniently carried by the carrying grip.

WARNING:

• Be sure that the tool is unplugged first.

• Stopper pin is for carrying purposes only and not for

any cutting operations.

Installing auxiliary plate (Fig. 2 & 3)

Install the auxiliary plate using the notch in the tool’s

base and secure it by tightening the hex bolt.

Bench mounting saw (Fig. 4)

This tool should be bolted with two bolts to a level and

stable surface using the bolt holes provided in the tool’s

base. This will help prevent tipping and possible injury.

Installing or removing saw blade

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the blade.

To remove the blade, use the socket wrench to loosen the

hex bolt holding the center cover by turning it more than

three turns counterclockwise. Raise the safety cover and

center cover. (Fig. 5)

Press the shaft lock so that the blade cannot revolve and

use the socket wrench to loosen the hex bolt clockwise.

Then remove the hex bolt, outer flange and blade.

(Fig. 6)

To install the blade, mount it onto the spindle, making

sure that the direction of the arrow on the surface of the

blade matches the direction of the arrow on the blade

case. (Fig.7)

CAUTION:

• For all countries other than European countries

(Fig.8)

The silver ring 25.4 mm in outer diameter is factory-

installed onto the spindle. The black ring 25 mm in

outer diameter is included as standard equipment.

Before mounting the blade onto the spindle, always be

sure that the correct ring for the arbor hole of the blade

you intend to use is installed onto the spindle.

• For European countries (Fig. 8)

The ring 30 mm in outer diameter is factory-installed

onto the spindle.

Install the flange and hex bolt, and then use the socket

wrench to tighten the hex bolt securely counterclockwise

while pressing the shaft lock. Then tighten the hex bolt

clockwise to secure the center cover. (Fig. 9)

CAUTION:

Use only the Makita socket wrench provided to install or

remove the blade. Failure to do so may result in overtight-

ening or insufficient tightening of the hex bolt. This could

cause an injury.

12

Safety cover (Fig. 10)

When lowering the handle, the safety cover rises auto-

matically. The cover returns to its original position when

the cut is completed and the handle is raised. NEVER

DEFEAT OR REMOVE THE SAFETY COVER. In the

interest of your personal safety, always maintain the

safety cover in good condition. Any irregular operation of

the safety cover should be corrected immediately.

NEVER USE THE TOOL WITH A FAULTY SAFETY

COVER. If the see-through safety cover becomes dirty, or

sawdust adheres to it in such a way that the blade and/or

workpiece is no longer easily visible, unplug the saw and

clean the cover carefully with a damp cloth. Do not use

solvents or any petroleum-based cleaners on the plastic

cover.

Dust bag (Fig.11 & 12)

The use of the dust bag makes cutting operations clean

and dust collection easy. To attach the dust bag, fit the

bag’s entry port over the dust spout. When the dust bag

is about half full, remove the dust bag from the tool and

pull the fastener out. Empty the dust bag of its contents,

tapping it lightly so as to remove particles adhering to the

insides which might hamper further collection.

Switch action

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

• When not using the tool, remove the lock-off button and

store it in a secure place. This prevents unauthorized

operation.

• Do not pull the trigger hard without pressing in the lock-

off button. This can cause breakage of the switch.

For all countries other than European countries

(Fig. 13)

To prevent the trigger from being accidentally pulled, a

lock-off button is provided. To start the tool, press in the

lock-off button and pull the trigger. Release the trigger to

stop.

For European countries (Fig. 14)

To prevent the trigger from being accidentally pulled, a

lock-off button is provided. To start the tool, push the

lever to the left, press in the lock-off button and then pull

the trigger. Release the trigger to stop.

Kerf board (Fig. 15)

This tool is provided with the kerf board in the turn base.

If the kerf groove has not yet been cut in the kerf board by

the factory, you should cut the groove before actually

using the tool to cut a workpiece. Switch on the tool and

lower the blade gently to cut a groove in the kerf board.

Sub-fence (Fig. 16 & 17)

This tool is equipped with the sub-fence which should

ordinarily be positioned as shown in Fig.16. However,

when performing left bevel cuts, set it to the left position

as shown in Fig.17.

Maintaining maximum cutting capacity

(Fig. 18 & 19)

Unplug the tool before any adjustment is attempted. This

tool is factory adjusted to provide the max. cutting capac-

ity for a 260 mm saw blade. When the diameter of the

blade has been reduced due to sharpening, adjust the

depth adjusting bolt by turning it with the socket wrench.

The saw blade is lowered by turning the depth adjusting

bolt counterclockwise and raised by turning it clockwise.

Adjust so that when the handle is in the fully lowered

position, there will be a distance of about 135 mm from

the front face of the guide fence to the point where the

front edge of the blade enters the kerf. With the tool

unplugged, rotate the blade by hand while holding the

handle all the way down. Be sure that the blade does not

contact any part of the lower base when the handle is

lowered completely.

Positioning for adjusting the miter angle (Fig. 20)

Loosen the grip by turning counterclockwise. Turn the

turn base while pressing down the latch spring. When

you have moved the grip to the position where the pointer

indicates the desired angle on the miter scale, securely

tighten the grip clockwise.

CAUTION:

When turning the turn base, be sure to raise the handle

fully.

Positioning for adjusting the bevel angle

(Fig. 21 & 22)

The saw blade tilts up to 45° to the left only when the

sub-fence is set to the left position as shown in Fig. 17.

To adjust the bevel angle, loosen the lever at the rear of

the tool. Tilt the blade to the left so that the pointer indi-

cates the desired angle on the bevel scale. Then tighten

the lever firmly to secure the arm.

CAUTION:

When tilting the saw blade, be sure to raise the handle

fully.

Securing workpiece

WARNING:

It is extremely important to always secure the workpiece

properly and tightly with the vise. Failure to do so can

cause the tool to be damaged and/or the workpiece to be

destroyed. PERSONAL INJURY MAY ALSO RESULT.

Also, after a cutting operation, DO NOT raise the blade

until the blade has come to a complete stop.

1. Vertical vise (Fig.23 & 27)

The vertical vise can be installed on the guide

fence or the holder assembly (optional accessory).

Insert the vise rod into the hole in the guide fence or

the holder assembly and tighten the screw to secure

the vise rod. Position the vise arm according to the

thickness and shape of the workpiece and secure

the vise arm by tightening the screw. Press the

workpiece flat against the guide fence and the turn

base. Position the workpiece at the desired cutting

position and secure it firmly by tightening the clamp

screw.

13

CAUTION:

The workpiece must be secured firmly against the

turn base and guide fence with the vise during all

operations.

If some part contacts the vise, re-position the vise

arm. Press the workpiece flat against the guide

fence and the turn base. Position the workpiece at

the desired cutting position and secure it firmly by

tightening the clamp screw of the vise.

CAUTION:

When cutting long workpieces, use supports that are

as high as the top surface level of the turn base.

(Fig. 24)

2. Horizontal vise (optional accessory)

(Fig. 25 & 26)

The horizontal vise can be installed on either the left

or right side of the base. When performing 15° or

greater miter cuts, install the horizontal vise on the

side opposite the direction in which the turn table is

to be turned. By turning the knob on the vise coun-

terclockwise, the screw is released and the vise

shaft can be moved rapidly in and out. By turning the

knob clockwise, the screw remains secured. To grip

workpieces, turn the knob gently clockwise until the

projection reaches its topmost position, then fasten

securely. If the knob is forced in or pulled out while

being turned clockwise, the projection may stop at

an angle. In this case, turn the knob back counter-

clockwise until the screw is released, before turning

again gently clockwise.

3. Holders and holder assembly(optional accesso-

ries)

The holders and the holder assembly can be

installed on either side as a convenient means of

supporting workpieces horizontally. Install them as

shown in Fig. 27. Then tighten the screws firmly to

secure the holders and the holder assembly.

(Fig. 27)

When cutting long workpieces, use the holder-rod

assembly (optional accessory). It consists of two

holder assemblies and two rods 12. (Fig.28)

CAUTION:

Always support long workpieces level with the top

surface of the turn base for accurate cuts and to pre-

vent dangerous loss of control of the tool.

Operation

CAUTION:

• Before use, be sure to release the handle from the low-

ered position by pulling the stopper pin.

• Make sure the blade is not contacting the workpiece,

etc. before the switch is turned on.

• Do not apply excessive pressure on the handle when

cutting. Too much force may result in overload of the

motor and/or decreased cutting efficiency.

• Gently press down the handle to perform the cut. If the

handle is pressed down with force or if lateral force is

applied, the blade will vibrate and leave a mark (saw

mark) in the workpiece and the precision of the cut will

be impaired.

When cutting with this tool, the thickness of the blade is

cut out of the workpiece as well. Therefore, your cutting

line should be on either the left or right side of the groove

in the kerf board. Switch on the tool and wait until the

blade attains full speed before lowering gently into the

cut. When the blade contacts the workpiece, gradually

bear down on the handle to perform the cut. When the

cut is completed, switch off the tool and WAIT UNTIL

THE BLADE HAS COME TO A COMPLETE STOP

before returning the blade to its fully elevated position. A

thin piece of cut off material could otherwise contact the

coasting blade and be thrown around dangerously.

(Fig. 29)

1. Miter cutting

Refer to the previously covered “Positioning for

adjusting the miter angle”.

2. Bevel cut (Fig. 30)

• Left 0° – 45° bevel cuts can be performed.

• Set the sub-fence to the left position as shown in

Fig. 17. Loosen the lever and tilt the saw blade to

set the bevel angle. Be sure to retighten the lever

firmly to secure the selected bevel angle safely.

Secure the workpiece with the vise. Switch on the

tool and wait until the blade attains full speed.

Then gently lower the handle to the fully lowered

position while applying pressure in parallel with the

blade. When the cut is completed, switch off the

tool and WAIT UNTIL THE BLADE HAS COME TO

A COMPLETE STOP before returning the blade to

its fully elevated position.

CAUTION:

• When performing the bevel cut with the workpiece

secured on the left side of the turn base, it will cre-

ate a condition where the piece cut off will come to

rest on the blade. If the blade is raised while the

blade is still rotating, this piece may be caught in

the blade, causing fragments to be scattered

around which is dangerous. The blade should be

gently raised only after the blade has come to a

complete stop.

• When pressing down the handle, apply pressure in

parallel with the blade. If a force is applied perpen-

dicularly to the turn base or if the pressure direc-

tion is changed during a cut, the precision of the

cut will be impaired.

• Always set the sub-fence to the left position as

shown in Fig. 17 when performing bevel cuts.

3. Compound cutting

Compound cutting can be performed at angle shown

in the table below.

When performing the compound cutting, refer to

“Miter cutting” and “Bevel cut” explanations.

Bevel angle Miter angle

45°

Left and right

0° – 45°

14

4. Cutting aluminum extrusion (Fig. 31)

When securing aluminum extrusions, use spacer

blocks or pieces of scrap as shown in Fig. 31 to pre-

vent deformation of the aluminum. Use a cutting

lubricant when cutting the aluminum extrusion to

prevent build-up of the aluminum material on the

blade.

CAUTION:

Never attempt to cut thick or round aluminum extru-

sions. Thick aluminum extrusions may come loose

during operation and round aluminum extrusions

cannot be secured firmly with this tool.

5. Wood facing (Fig. 32)

Use of wood facing helps to assure splinter-free cuts

in workpieces. Attach a wood facing to the guide

fence using the holes in the guide fence.

CAUTION:

• Use straight wood of even thickness as the wood

facing.

•See Fig. 32 concerning the dimensions for a sug-

gested wood facing.

6. Cutting repetitive lengths (Fig. 33)

When cutting several pieces of stock to the same

length, ranging from 240 mm to 400 mm, use of the

set plate (optional accessory) will facilitate more effi-

cient operation. Install the set plate on the holder as

shown in Fig. 33. Align the cutting line on your work-

piece with either the left or right side of the groove in

the kerf board, and while holding the workpiece from

moving, move the set plate flush against the end of

the workpiece. Then secure the set plate with the

screw. When the set plate is not used, loosen the

screw and turn the set plate out of the way.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,

but rough handling may have affected the alignment. If

your tool is not aligned properly, perform the following:

1) Miter angle (Fig. 34 & 35)

Loosen the grip and set the turn base at zero

degrees by turning the turn base. Tighten the grip

securely and loosen the hex bolts on the guide

fence. Square the side of the blade with the face of

the guide fence using a triangular rule, try-square,

etc. by moving the right side of the guide fence.

Then securely tighten the hex bolts on the guide

fence in the order indicated in Fig. 35.

2) Bevel angle

i) 0° bevel angle

Loosen the lever at the rear of the tool. Loosen

the hex nut and turn the hex bolt (A) two or three

revolutions clockwise so that the blade tilts to the

right. (Fig. 36)

Lower the handle fully and square the side of the

blade with the top surface of the turn base using

the triangular rule, try-square, etc. by turning the

hex bolt (A) counterclockwise. Then tighten the

hex nut to secure the hex bolt (A). (Fig. 37)

Make sure that the pointer on the arm indicates

0° on the bevel scale on the arm holder. If the

pointer does not indicate 0°, loosen the screw

securing the pointer and adjust the pointer.

(Fig. 38)

ii) 45° bevel angle

Adjust 45° bevel angle only after performing 0°

bevel angle adjustment. To adjust 45° bevel angle,

loosen the lever and tilt the saw blade to the left

fully. Make sure that the pointer on the arm indi-

cates 45° on the bevel scale on the arm holder. If

the pointer does not indicate 45°, turn the hex bolt

(B) on the side of the arm until the pointer indi-

cates 45°. (Fig. 38)

Replacement of carbon brushes

(Fig. 39 & 40)

Replace carbon brushes when they are worn down to the

limit mark. Both identical carbon brushes should be

replaced at the same time.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

15

Noise and Vibration of Model LS1040

The typical A-weighted noise levels are

sound pressure level: 93 dB (A)

sound power level: 106 dB (A)

– Wear ear protection. –

The typical weighted root mean square acceleration

value is not more than 2.5 m/s

2

.

EC-DECLARATION OF CONFORMITY

The undersigned, Yasuhiko Kanzaki, authorized by

Makita Corporation, 3-11-8 Sumiyoshi-Cho, Anjo,

Aichi 446-8502 Japan declares that this product

(Serial No. : series production) manufactured by Mak-

ita Corporation in P.R.C is in compliance with the fol-

lowing standards or standardized documents,

EN61029, EN55014, EN61000

in accordance with Council Directives,

73/23/EEC, 89/336/EEC and 98/37/EC.

Yasuhiko Kanzaki

CE97

Director

MAKITA INTERNATIONAL EUROPE LTD.

Michigan Drive, Tongwell, Milton Keynes, Bucks

MK15 8JD, ENGLAND

Page is loading ...

Makita Corporation

Anjo, Aichi, Japan

884085A204

Makita LS1040 User manual

This manual is also suitable for

Makita LS1040 User manual

in other languages

Related papers

Other documents