DeWalt D26441 Owner's manual

Page is loading ...

2

Copyright DEWALT

Dansk 6

Deutsch 12

English 19

Español 25

Français 31

Italiano 37

Nederlands 43

Norsk 49

Português55

Suomi 61

Svenska 67

Türkçe

73

EÏÏËÓÈÎ· 79

Page is loading ...

19

ENGLISH

PALM GRIP SANDER D26441

Congratulations!

You have chosen a DEWALT tool. Years of

experience, thorough product development and

innovation make D

EWALT one of the most reliable

partners for professional power tool users.

Technical data

D26441

Voltage V 230

(U.K. & Ireland only) V 230/115

Power input W 230

Pad size mm 108 X 115

Orbits min

-1

14,000

Orbit mm 1.4

Weight kg 1.4

Fuses:

Europe 230 V tools 10 Amperes, mains

U.K. & Ireland 230 V tools 13 Amperes, in plugs

U.K. & Ireland 115 V tools 16 Amperes, mains

The following symbols are used throughout this

manual:

Denotes risk of personal injury, loss of life

or damage to the tool in case of non-

observance of the instructions in this

manual.

Denotes risk of electric shock.

Fire hazard.

Explosion hazard.

EC-Declaration of conformity

D26441

D

EWALT declares that these power tools have been

designed in compliance with: 98/37/EC, 89/336/EEC,

73/23/EEC, 86/188/EEC, EN 60745-1,

EN 60745-2-4, EN 55014-2, EN 55014-1,

EN 61000-3-2 & EN 61000-3-3.

For more information, please contact D

EWALT at the

address below, or refer to the back of the manual.

D26441

L

pA

(sound pressure) dB(A) 79

L

WA

(acoustic power) dB(A) 90

Weighted RMS acceleration value m/s

2

9.3

K

pA

(sound pressure uncertainty) dB(A) 3

K

WA

(acoustic power uncertainty) dB(A) 3

Director Engineering and Product Development

Horst Großmann

DEWALT, Richard-Klinger-Straße 11

D-65510, Idstein, Germany

20

ENGLISH

General safety rules

Warning! Read all instructions. Failure to follow

all instructions listed below may result in electric

shock, fire and/or serious injury. The term

„power tool“ in all of the warnings listed below

refers to your mains operated (corded) power

tool or battery operated (cordless) power tool.

SAVE THESE INSTRUCTIONS.

1 Work area

a Keep work area clean and well lit. Cluttered

and dark areas invite accidents.

b Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

c Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2 Electrical safety

a Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded)

power tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

b Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or

grounded.

c Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

3 Personal safety

a Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b Use safety equipment. Always wear eye

protection. Safety equipment such as dust

mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

c Avoid accidental starting. Ensure the switch

is in the off position before plugging in.

Carrying power tools with your finger on the

switch or plugging in power tools that have the

switch on invites accidents.

d Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery

or long hair can be caught in moving parts.

g If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly

used. Use of these devices can reduce dust

related hazards.

4 Power tool use and care

a Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

b Do not use the power tool if the switch does

not turn it on and off. Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

c Disconnect the plug from the power source

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

21

ENGLISH

d Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tools operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g Use the power tool, accessories and tool bits

etc., in accordance with these instructions

and in the manner intended for the particular

type of power tool, taking into account the

working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5 Service

a Have your power tool serviced by a qualified

repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional safety instructions for sanders

Take special care when sanding some

woods (e.g. beech, oak) and metal which

may produce toxic dust. Wear a dust

mask specifically designed for protection

against toxic dust and fumes and ensure

that persons within or entering the work

area are also protected.

• Use this tool in a well-ventilated area when

sanding ferrous metals. Do not operate the tool

near flammable liquids, gases or dust. Sparks or

hot particles from sanding or arcing motor

brushes may ignite combustible materials.

Sanding paint

Observe the applicable regulations for sanding paint.

Pay special attention to the following:

1 Whenever possible, use a vacuum extractor for

dust collection.

2 Take special care when sanding paint which is

possibly lead based:

• Do not let children or pregnant women enter the

work area.

• All persons entering the work area should wear a

mask specially designed for protection against

lead paint dust and fumes.

• Do not eat, drink or smoke in the work area.

3 Dispose of dust particles and any other removal

debris safely.

Package contents

The package contains:

1 Palm grip sander

1 Dustbag

1 Dust extraction adapter

1 Sheet of sanding paper

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or

accessories which may have occurred during

transport.

• Take the time to thoroughly read and understand

this manual prior to operation.

Description (fig. A)

Your palm grip sander D26441 has been designed

for sanding of wood, metal and plastics in a

professional environment.

1 On/off switch

2 Dust extraction outlet

3 Sanding pad

4 Sanding sheet clamp knob

Electrical safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

22

ENGLISH

Mains plug replacement

(U.K. & Ireland only)

Should your mains plug need replacing and you

are competent to do this, proceed as instructed

below. If you are in doubt, contact an authorized

D

EWALT repair agent or a qualified electrician.

• Disconnect the plug from the supply.

• Cut off the plug and dispose of it safely; a plug

with bared copper conductors is dangerous if

engaged in a live socket outlet.

• Only fit 13 Amperes BS1363A approved plugs

fitted with the correctly rated fuse (1).

• The cable wire colours, or a letter, will be marked

at the connection points of most good quality

plugs. Attach the wires to their respective points

in the plug (see below). Brown is for Live (L) (2)

and Blue is for Neutral (N) (4).

• Before replacing the top cover of the mains plug

ensure that the cable restraint (3) is holding the

outer sheath of the cable firmly and that the two

leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N)

wires to the earth pin marked E or

.

For 115 V units with a power rating exceeding 1500 W,

we recommend to fit a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1.5 mm

2

.

When using a cable reel, always unwind the cable

completely.

Also refer to the table below.

Conductor size (mm

2

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Fitting sanding sheets (fig. B1 - B4)

Fitting regular sanding sheets (fig. B1 - B3)

• Soften the sanding sheet by rubbing its non-

abrasive side over the edge of a worktop.

• Release both sanding sheet clamp knobs (4).

• Hold the sanding pad (3) with one hand and align

the dust extraction holes (5).

• Slide the sanding sheet under the sanding sheet

clamp (4).

• Engage the corresponding sanding paper clamp

knob (4).

• Stretch the sanding paper firmly over the sanding

pad (3) and repeat for the other clamp.

Fitting hook and loop sanding sheets (fig. B4)

• Place the tool on a table, sanding pad (3) up.

• Place the sanding sheet directly on top of the

sanding pad.

• Hold the sanding pad (3) with one hand and align

the dust extraction holes (5).

• Press the sheet firmly onto the sanding pad.

23

ENGLISH

Dust extraction (fig. C)

Since woodworking with a sander

produces dust, always install a dustbag

designed in compliance with the

applicable directives regarding dust

emission.

Do not use a dustbag or vacuum

extractor without proper spark protection

when sanding metal.

The tool is supplied with an adapter for connecting a

dustbag or a vacuum extractor.

• Fit the dust extraction adaptor (6) onto the outlet

(2) as shown.

• Attach the dustbag (7) by aligning the open-

ended slots (8) with the notches (9) and fitting the

bag onto the adaptor (6).

• Turn the assembly clockwise to lock it in position.

• Alternatively, connect the tool to a vacuum

extractor using the adaptor (6).

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Make sure all materials to be sanded are well

secured.

• Apply only a gentle pressure to the workpiece.

Excessive pressure does not improve the

sanding effect, but only results in an increased

load on the machine and causes the abrasive to

tear.

• Avoid overloading.

Do not sand magnesium!

Switching on and off (fig. A)

• To switch the tool on, set the on/off switch to

position I.

• To switch the tool off, set the on/off switch to

position O.

Sanding (fig. A)

• Start with the coarsest grit size.

• As the tool produces small scratch marks in all

directions, it is not necessary to sand with the

grain.

• Check your work at short intervals.

• Always switch off the tool when work is finished

and before unplugging.

Emptying the dustbag (fig. C)

For efficient dust extraction empty the dust collector

when it is about one third full.

• To empty the dust collector, pull it off together

with the adaptor.

• Remove the dustbag (7) from the adaptor (6) by

turning it counter-clockwise and pulling it off.

• Empty the contents of the bag into a waste

container. If necessary, use a vacuum extractor

to clean the dustbag, applying suction to the

interior surface.

• Re-fit the dust extraction adaptor.

• Re-fit the dustbag.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

Keep the ventilation slots clear and regularly clean

the housing with a soft cloth.

• After the tool is used in metal sanding

applications without dustbag, clean the tool

using low-pressure air.

24

ENGLISH

Protecting the environment

Separate collection. This product must

not be disposed of with normal

household waste.

Should you find one day that your D

EWALT product

needs replacement, or if it is of no further use to you,

do not dispose of it with household waste. Make this

product available for separate collection.

Separate collection of used products

and packaging allows materials to be

recycled and used again. Re-use of

recycled materials helps prevent

environmental pollution and reduces the

demand for raw materials.

Local regulations may provide for separate collection

of electrical products from the household, at

municipal waste sites or by the retailer when you

purchase a new product.

D

EWALT provides a facility for the collection and

recycling of D

EWALT products once they have

reached the end of their working life. To take

advantage of this service please return your product

to any authorised repair agent who will collect them

on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

D

EWALT office at the address indicated in this

manual. Alternatively, a list of authorised D

EWALT

repair agents and full details of our after-sales

service and contacts are available on the Internet at:

www.2helpU.com

GUARANTEE

• 30 DAY NO RISK SATISFACTION GUARANTEE •

If you are not completely satisfied with the

performance of your D

EWALT tool, simply return

it within 30 days, complete as purchased, to the

point of purchase, for a full refund or exchange.

Proof of purchase must be produced.

• ONE YEAR FREE SERVICE CONTRACT •

If you need maintenance or service for your

D

EWALT tool, in the 12 months following

purchase, it will be undertaken free of charge at

an authorized D

EWALT repair agent. Proof of

purchase must be produced. Includes labour and

spare parts for Power Tools. Excludes

accessories.

• ONE YEAR FULL WARRANTY •

If your DEWALT product becomes defective due

to faulty materials or workmanship within

12 months from the date of purchase, we

guarantee to replace all defective parts free of

charge or, at our discretion, replace the unit free

of charge provided that:

• The product has not been misused.

• Repairs have not been attempted by

unauthorized persons.

• Proof of purchase date is produced.

This guarantee is offered as an extra benefit

and is additional to consumers statutory rights.

For the location of your nearest authorized

D

EWALT repair agent, please use the appropriate

telephone number on the back of this manual.

Alternatively, a list of authorized D

EWALT repair

agents and full details on our after-sales service

are available on the Internet at www.2helpU.com.

Page is loading ...

85

E°°À∏™∏

• 30 ∏ªEƒø¡ E°°À∏™∏ π∫∞¡√¶√π∏∆π∫∏™

∞¶√¢√™∏™ •

E¿Ó ‰ÂÓ Â›ÛÙÂ Ï‹Úˆ˜ ÈÎ·ÓÔÔÈËÌ¤ÓÔÈ ·ﬁ ÙËÓ

·ﬁ‰ÔÛË ÙÔ˘ ÂÚÁ·ÏÂ›Ô˘ Û·˜ DeWALT, ·ÏÒ˜

ÂÈÛÙÚ¤„ÙÂ ÙÔ ÂÓÙﬁ˜ 30 ËÌÂÚÒÓ, Ï‹ÚÂ˜

ﬁˆ˜ ÙÔ ·ÁÔÚ¿Û·ÙÂ, ·ﬁ ÙÔ ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓÔ

∫·Ù¿ÛÙËÌ· DeWALT, ÁÈ· Ï‹ÚË ÂÈÛÙÚÔÊ‹

¯ÚËÌ¿ÙˆÓ. ¶Ú¤ÂÈ Ó· ÚÔÛÎÔÌÈÛÙÂ› ·ﬁ‰ÂÈÍË

·ÁÔÚ¿˜.

• E¡√™ E∆√À™ ™Àªµ√§∞π√ °π∞ ¶§∏ƒE™ ™Eƒµπ™ •

E¿Ó ¯ÚÂÈ¿˙ÂÛÙÂ Û˘ÓÙ‹ÚËÛË ‹ Û¤Ú‚È˜ ÁÈ· ÙÔ

ÂÚÁ·ÏÂ›Ô Û·˜ DeWALT, ÂÓÙﬁ˜ 12 ÌËÓÒÓ ·ﬁ

ÙËÓ ·ÁÔÚ¿, ·˘Ùﬁ ÌÔÚÂ› Ó· Á›ÓÂÈ ‰ˆÚÂ¿Ó ÛÂ

ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓÔ ∫·Ù¿ÛÙËÌ· Service. ¶Ú¤ÂÈ

Ó· ÚÔÛÎÔÌÈÛÙÂ› ·ﬁ‰ÂÈÍË ·ÁÔÚ¿˜.

∏ Û˘ÓÙ‹ÚËÛË/service ÂÚÈÏ·Ì‚¿ÓÂÈ ÂÚÁ·Û›·

Î·È ·ÓÙ·ÏÏ·ÎÙÈÎ¿ ÁÈ· Ù· ËÏÂÎÙÚÈÎ¿ ÂÚÁ·ÏÂ›·

DeWALT.

• E¡√™ E∆√À™ ¶§∏ƒ∏™ E°°À∏™∏ •

E¿Ó ÙÔ ÚÔ˚ﬁÓ Û·˜ ÙË˜ DeWALT ·ÚÔ˘ÛÈ¿˙ÂÈ

·ÓˆÌ·Ï›· ÔÊÂÈÏﬁÌÂÓË ÛÂ ÂÏ¿ÙÙˆÌ· ÙˆÓ

˘ÏÈÎÒÓ ‹ ÙË˜ Î·Ù·ÛÎÂ˘‹˜ ÂÓÙﬁ˜ 12 ÌËÓÒÓ ·ﬁ

ÙËÓ ËÌÂÚÔÌËÓ›· ÙË˜ ·ÁÔÚ¿˜, ÂÁÁ˘ÒÌ·ÛÙÂ ÙË

‰ˆÚÂ¿Ó ·ÓÙÈÎ·Ù¿ÛÙ·ÛË ﬁÏˆÓ ÙˆÓ

ÂÏ·ÙÙˆÌ·ÙÈÎÒÓ ÌÂÚÒÓ, ‹ Î·Ù¿ ÙËÓ ÎÚ›ÛË Ì·˜,

ÙË ‰ˆÚÂ¿Ó ·ÓÙÈÎ·Ù¿ÛÙ·ÛË ÔÏﬁÎÏËÚË˜ ÙË˜

ÌÔÓ¿‰·˜ ˘ﬁ ÙËÓ ÚÔ¸ﬁıÂÛË ﬁÙÈ:

• ¢ÂÓ ¤¯ÂÈ Á›ÓÂÈ Î·Î‹ ÌÂÙ·¯Â›ÚÈÛË ÙÔ˘

ÚÔ˚ﬁÓÙÔ˜.

• ¢ÂÓ ¤¯ÂÈ ÂÈ¯ÂÈÚËıÂ› ÂÈÛÎÂ˘‹ ·ﬁ ÌË

ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓÔ ¿ÙÔÌÔ.

• £· ÚÔÛÎÔÌÈÛÙÂ› ·ﬁ‰ÂÈÍË ÙË˜ ËÌÂÚÔÌËÓ›·˜

·ÁÔÚ¿˜.

°È· Ó· ÂÓÙÔ›ÛÂÙÂ ÙÔ ÏËÛÈ¤ÛÙÂÚÔ

ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓÔ ∫·Ù¿ÛÙËÌ· Service,

·Ú·Î·ÏÂ›ÛıÂ Ó· ÙËÏÂÊˆÓ‹ÛÂÙÂ ÛÙÔ

ÏËÛÈ¤ÛÙÂÚÔ ∫·Ù¿ÛÙËÌ· Service ÙË˜ ÂÙ·ÈÚ›·˜

Ì·˜ (‚Ï¤Â ·Ú·Î¿Ùˆ). EÓ·ÏÏ·ÎÙÈÎ¿, ÌÈ· Ï›ÛÙ·

ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓˆÓ ∫·Ù¿ÛÙËÌ·ÙˆÓ Service

DeWALT Î·È ÔÏÏ¤˜ ÏÂÙÔÌ¤ÚÂÈÂ˜ Û¯ÂÙÈÎ¿ ÌÂ

ÙËÓ ˘ËÚÂÛ›· after-sales Â›Ó·È ‰È·ı¤ÛÈÌÂ˜ ÛÙÔ

Internet ÛÙË ‰ÈÂ‡ı˘ÓÛË www.2helpU.com.

∂§§∏¡π∫∞

Page is loading ...

88

Belgique et Luxembourg DEWALT Tel: +32 (0)015 - 15 47 9211

België en Luxemburg Mechelen Campus, Schaliënhoevedreef 20

E

Fax: +32 (0)015 - 15 47 9210

B-2800 Mechelen www.dewalt.com

Danmark D

EWALT Tlf: 70 20 15 10

Sluseholmen 2-4 Fax: 36 94 49 01

2450 København SV www.dewalt-nordic.com

Deutschland D

EWALT Tel: 06126-21-1

Richard-Klinger-Straße Fax: 06126-21-2770

65510 Idstein www.dewalt.de

EÏÏ¿˜ Black & Decker (EÏÏ¿˜) ∞.E. TËÏ: 210 8981616

™ÙÚ¿‚ˆÓÔ˜ 7 & µÔ˘ÏÈ·ÁÌ¤ÓË˜ 159 º·Í: 210 8983285

°Ï˘Ê¿‰· 16674, ∞ı‹Ó·

España D

EWALT Tel: 934 797 400

Parque de Negocios “Mas Blau” Fax: 934 797 439

Edificio Muntadas, c/Bergadá, 1, Of. A6

08820 El Prat de Llobregat (Barcelona)

France D

EWALT Tel: 472 20 39 72

Le Paisy Fax: 472 20 39 02

BP 21, 69571 Dardilly Cedex www.dewalt.fr

Schweiz DeWALT Tel: 01 - 730 67 47

Suisse In der Luberzen 40 Fax: 01 - 730 70 67

Svizzera 8902 Urdorf www.dewalt.ch

Ireland D

EWALT Tel: 00353-2781800

Calpe House Rock Hill Fax: 00353-2781811

Black Rock, Co. Dublin www.dewalt.ie

Italia D

EWALT Tel: 800-014353

Viale Elvezia 2 Fax: 039-2387592

20052 Monza (Mi) www.dewalt.it

Nederland D

EWALT BV Tel: 0164 283000

Joulehof 12 Fax: 0164 283100

4622 RG Bergen Op Zoom www.dewalt.com

Norge D

EWALT Tel: 22 90 99 00

Postboks 4814, Nydalen Fax: 22 90 99 01

0422 Oslo www.dewalt-nordic.com

Österreich D

EWALT Tel: 01 - 66116 - 0

Werkzeugevertriebs GmbH Fax: 01 - 66116 - 14

Erlaaerstraße 165, Postfach 320,1231 Wien www.dewalt.at

Portugal D

EWALT Tel: 214 66 75 00

Rua Egas Moniz 173 Fax: 214 66 75 75

João do Estoril, 2766-651 Estoril

Suomi D

EWALT Puh: 010 400 430

Keilasatama 3 Faksi: (09) 2510 7100

02150 Espoo www.dewalt-nordic.com

D

EWALT Tel: 010 400 430

Kägelhamnen 3 Fax: (09) 2510 7100

02150 Esbo www.dewalt-nordic.com

Sverige D

EWALT, c/o Regus Tel: 031 68 61 00

Fabriksgatan 7 Fax: 031 68 60 08

412 50 Göteborg www.dewalt-nordic.com

Türkiye

Merkez Servis

Tel:

0212 361 60 20

Tersane Cad.

Faks:

0212 361 60 19

Nafe Sokak 1-3/4 Karaköy - Istanbul

United Kingdom D

EWALT Tel: 01753-56 70 55

210 Bath Road Fax: 01753-57 21 12

Slough, Berks SL1 3YD www.dewalt.co.uk

06/06

626665-00

DeWalt D26441 Owner's manual

This manual is also suitable for

DeWalt D26441 Owner's manual

in other languages

Related papers

Other documents