American Standard 2771L.020 User manual

Brand: American Standard

Model: 2771L.020

Category: Space heaters

Type: User manual

753737-100 Rev. C

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The

whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the

whirlpool installation are your selected fittings and electrical connections.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

MODEL 2422L / LA / V / VA 5' x 32"

MODEL 6060L / V CORNER

MODEL 2771L / LA / V / VA 5' x 36"

MODEL 2645L / LA / V / VA OVAL

MODEL 7236L / LA / V / VA 6' x 36"

MODEL 2425L / V - LHO 5' x 32" IA-LHO

MODEL 2425L / V - RHO 5' x 32" IA-RHO

MODEL 2901L SAVONA

MODEL 2908L / LA REMINISCENCE

MODEL 2711L ELLISSE

MODEL 2773L CADET 6' x 36"

MODEL 2774L / LA CADET 6' x 42"

MODEL 2775L CADET CORNER

MODEL 2805L 5' x 42"

All product names listed herein are trademarks

of AS Americas Inc. unless otherwise noted.

FOR AFTER-SALES SERVICE CALL 1 (00) -10 WEEKDAYS.

INSTALLATION GUIDE FOR

LIFETIME™ / EVOLUTION™

WHIRLPOOLS AND BATHTUBS



753737-100 Rev. C

TABLE OF CONTENTS:

Safety Instructions............................................................................Page 3

General Information..........................................................................Page 

Optional Components.......................................................................Page 

Specifications....................................................................................Page 5

Roughing-in Reference.....................................................................Page -

Framing and Support Instructions.....................................................Page 

Mounting Instructions........................................................................Page 10

Electrical Connections.......................................................................Page 11

00L/V Corner EZ-Install Heater.....................................................Page 1

Drain Connection and System Test...................................................Page 13

Care and Cleaning.............................................................................Page 13

Warranty............................................................................................Page 1

753737-100 Rev. C

SAVE THESE INSTRUCTIONS

WARNING:

Risk of personal injury.

Do not permit children to use this unit without adult supervision.

WARNING: Risk of personal injury. Do not operate this unit without the guard over the suction fitting.

WARNING:

Risk of electric shock. Do not permit electrical appliances (hair dryer, telephone, radio, etc.) within

0 inches (15mm) of this unit.

WARNING: Risk of hyperthermia and possible drowning. People using medications and/or having adverse

medical history should consult a physician before using this product.

WARNING: Risk of personal injury. Do not overfill unit before entering. Entering tub when filled more than /3

can cause overflow and slippery conditions. Exercise caution when entering and exiting.

WARNING:

No Food or Alcoholic Beverages.

Use of your bathtub immediately after meals is not

recommended. Avoid alcohol consumption before or during bathing. Alcoholic beverages can cause drowsiness or

hyperthermia resulting in loss of consciousness or even drowning.

WARNING: Pregnancy. If you are or think you may be pregnant, consult your physician before using the bathtub.

Never drop or insert any object into any opening.

Use this unit only for its intended use as described in this manual. Do not use any attachments not recommended by

American Standard.

The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter

(GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI,

push the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI

fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the bathtub without the test button

being pushed, a ground current is flowing, indicating the possibility of an electric shock. Do not use this hydromassage

bathtub. Disconnect the hydromassage bathtub and have the problem corrected by a licensed electrician before using.

A pressure wire connector is provided on the exterior of the motor unit to permit connection of a no.  AWG solid

copper bonding conductor between this unit and all other electrical equipment and exposed metal in the vicinity, as

needed to comply with local requirements. To reduce the risk of an electric shock, connect this connector the

grounding terminal of your electric service or supply panel with a conductor equivalent in size to the circuit conductors

supplying this unit.

IMPORTANT SAFETY

INSTRUCTIONS

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, ELECTRIC SHOCK

OR INJURY TO PERSONS

READ AND FOLLOW ALL INSTRUCTIONS!



753737-100 Rev. C

Lifetime™/Evolution™ Corner

Lifetime™/Evolution™ 5' x 3"

Lifetime™/Evolution™ 5' x 3"

Lifetime™/Evolution™ ' x 3"

Lifetime™/Evolution™ 5' x 3" IA

Lifetime™/Evolution™ Oval

Lifetime™ Savona

Lifetime™ Reminiscence

Lifetime™ Ellisse

Lifetime™ Cadet ' x 3"

Lifetime™ Cadet ' x "

Lifetime™ Cadet Corner

Lifetime™ 5' x "

00



771

73

5

5

01

0

711

773

77

775

05

INCLUDED

0707.00

1.01

71.01

INTEGRAL

.01

NOT

AVAILABLE

NOT

AVAILABLE

NOT

AVAILABLE

7.01

NOT

AVAILABLE

10.00

15.500.00

15.500.00*

15.500.00

153.70.00

Optional Components

(Not Included)

Required Components

(Not Included)

E-Z

Install

Heater

Apron

Kit

Tile

Bead

Kit

Bath

Filler

•

153.70.XXX

15.05.XXX*

153.70.XXX

Drain

•

(Specify

Finish)

Drain

•

(White)

List of Required Tools and Supplies:

Tools

• Level

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard Woodworking Tools

• Personal Safety Equipment

• Caulking Gun

Supplies

• Nails

• Putty

• Caulking (waterproof)

• 1 x  Stringers

• Drop Cloth

• Cement, Plaster, Grout

General Installation Information

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your

vendor immediately. After inspection and during installation, protect the bath from construction damage. Before

installation, and before enclosing with wallboard, tile, etc., the bath must be filled with water and operated to

check for leaks that may have resulted from shipping damage or mishandling! Do not make modifications to

the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance

of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and

enclosing materials are provided by others.

For electrical requirements, refer to section titled “Whirlpool Electrical Installation Instructions”.

Check for availability of optional American Standard wall tiling bead (required for recess installation).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

Description

Model

Number

LIST OF OPTIONAL COMPONENTS (NOT INCLUDED):

• For these components please see your Vendor.

* These models require American Standard Lifetime™ Drain 15.05 or 15.500

WARNING: Do not lift whirlpool by the piping harness at any time.

753737-100 Rev. C

SPECIFICATIONS:

GENERAL SPECIFICATIONS FOR LIFETIME / EVOLUTION WHIRLPOOLS AND BATH TUBS

TABLE 1

SIDE VIEW

DRAIN / OVERFLOW

END VIEW

00L / V

Corner*

L / LA /

V / VA

5' x 3"

771L / LA /

V / VA

5' x 3"

73L / LA /

V / VA

' x 3"

5L / V

5' x 3”

IA-LHO /

IA-RHO

5L / LA /

V / VA

Oval

01L

Savona

0L / LA

Reminiscence

711L

Ellisse

773L

Cadet ' x 3"

77L / LA

Cadet ' x "

775L

Cadet Corner

05L

5' x "

A 1"

(57 mm)

B 13-3/"

(3 mm)

A 0-1/"

(511 mm)

B 11"

(7 mm)

A 0-1/"

(511 mm)

B 11"

(7 mm)

A 0-1/"

(511 mm)

B 11"

(7 mm)

A 1-1/"

(5 mm)

B 10-1/"

( mm)

A 15-1/"

(37 mm)

B -1/"

(0 mm)

A 1-1/"

(13 mm)

B -1/"

(15 mm)

A 15-1/"

(3 mm)

B "

(15 mm)

A 17-3/"

(1 mm)

B "

(10 mm)

A 17"

(3 mm)

B 1"

(305 mm)

A 1-1/"

(13 mm)

B -1/"

(15 mm)

A 1-1/"

(1 mm)

B -1/"

(15 mm)

A 1-1/"

(13 mm)

B -1/"

(15 mm)

130mm

(5-5/)

3mm

(3-1/)

3mm

(3-1/)

3mm

(3-1/)

73mm

(-7/)

mm

(1-3/)

10mm

(5-1/)

15mm

()

10mm

()

57mm

(-1/)

57mm

(-1/)

7mm

(11)

15mm

()

C 1-1/"

(5 mm)

C 0"

(50 mm)

C 0"

(50 mm)

C 0"

(50 mm)

C 0-1/"

(515 mm)

C 1-1/"

( mm)

C 0"

(50 mm)

C 1-1/"

( mm)

C 1-1/"

(5 mm)

C 1-1/"

( mm)

C 1-1/"

( mm)

C 1-1/"

( mm)

C 1-1/"

(5 mm)

Template

provided

5-1/"

(15 mm)

x 30-1/"

(77 mm)

5-1/"

(15 mm)

x 3-1/"

(7 mm)

70-1/"

(170 mm)

x 3-1/"

(7 mm)

N/D

"

(15 mm)

x 3"

(3 mm)

-3/"

(177 mm)

x "

(107 mm)

Template

provided

70-1/"

(171 mm)

x -1/"

(111 mm)

70-1/"

(171 mm)

x 3-1/"

(70 mm)

70-1/"

(171 mm)

x 0-1/"

(1537 mm)

Template

provided

5-1/"

(1 mm)

x 0-1/"

(10 mm)

Template

7510-100

0-3/1"

(15 mm)

x 30-1/"

(77 mm)

0-3/1"

(15 mm)

x 3-1/"

(7 mm)

7-3/1"

(133 mm)

x 3-1/"

(7 mm)

0-3/1"

(15 mm)

x 30-1/"

(77 mm)

-3/1"

(11 mm)

x 3-1/"

(7 mm)

7-3/1"

(133 mm)

x -1/"

(100 mm)

DESIRED

7-3/1"

(133 mm)

x "

(11 mm)

7-3/1"

(133 mm)

x 3"

(1 mm)

7-3/1"

(133 mm)

x "

(107 mm)

0-3/1"

(15 mm)

x "

(107 mm)

L 1mm (7-3/")

W 11mm (5-3/")

H 5mm (1-1/")

L 15mm (0")

W 13mm (3")

H 5mm (1-1/")

L 15mm (0")

W 1mm (3")

H 5mm (1-1/")

L 1mm (7")

W 1mm (3")

H 5mm (1-1/")

L 15mm (0")

W 13mm (3")

H 51mm (0-1/")

L 17mm (")

W 1mm (3")

H 50mm (1-3/")

L 1mm(7")

W 111mm(")

H 55mm(")

L 17mm (")

W 1mm (3")

H 1mm (-1/")

L 1mm (7")

W 11mm (")

H 5mm (1-1/")

L 1mm (7")

W 1mm (3")

H 50mm (1-3/")

L 1mm (7")

W 107mm (")

H 50mm (1-3/")

L 15mm (5")

W 15mm (0")

H 50mm (1-3/")

L 15mm (0")

W 107mm (")

H 5mm (1-1/")

10 lb.

( kg.)

7 lb.

(3 kg.)

75 lb.

(3 kg.)

10 lb.

( kg.)

 lb.

( kg.)

 lb.

( kg.)

15 lb.

( kg.)

5 lb.

(3 kg.)

1 lb.

(7 kg.)

101 lb.

(5 kg.)

137 lb.

( kg.)

130 lb.

(5 kg.)

130 lb.

(5 kg.)

 lb. (37 kg)/

(117 kg/sq.m)

5 lb./sq.ft.

0 lb. (313 kg)/

(0 kg/sq.m)

53 lb./sq.ft.

00 lb. (33 kg)/

(0 kg/sq.m)

53 lb./sq.ft.

1031 lb. (7 kg)/

(0 kg/sq.m)

57 lb./sq.ft.

75 lb. (30 kg)/

( kg/sq.m)

5 lb./sq.ft.

50 lb. (3 kg)/

(175 kg/sq.m)

3 lb./pies

cuadrados

3 lb. (1 kg)/

(11 kg/sq.m)

3 lb./sq.ft.

5 lb. ( kg)/

(11 kg/sq.m)

0 lb./sq.ft.

5 lb. (3 kg)/

(15 kg/sq.m)

0 lb./sq.ft.

751 lb. (31 kg)/

(10 kg/sq.m)

0 lb./sq.ft.

1 lb. (37 kg)/

(03 kg/sq.m)

 lb./sq.ft.

75 lb. (33 kg)/

(115 kg/sq.m)

3 lb./sq.ft.

 lb. (310 kg)/

(11 kg/sq.m)

3 lb./sq.ft.

Optional

Included

Optional

Included

Optional

 gal.

(35 l.)

7 gal.

(0 l.)

7 gal.

(3 l.)

111 gal.

(0 l.)

70 gal.

(5 l.)

5 gal.

(1 l.)

 gal.

(35 l.)

 gal.

(57 l.)

5 gal.

(30 l.)

7 gal.

( l.)

 gal.

(310 l.)

75 gal.

( l.)

 gal.

(3 l.)

71 gal.

( l.)

33 gal.

(15 l.)

50 gal.

(1 l.)

53 gal.

(01 l.)

3 gal.

(1 l.)

 gal.

(15 l.)

 gal.

(3 l.)

55 gal.

(0 l.)

7 gal.

(0 l.)

 gal.

(3 l.)

 gal.

(5 l.)

0 gal.

(7 l.)

5 gal.

(17 l.)

Description

Drain /

Overflow

Cut Out

Pier

G x F

Rough-In

Recess

E x D

Tub Edge to

Centerline

Overflow: J

Weight with

Water / Floor

Product

Weight

Apron /

Mounting

Heater Ready

for Field

Installation

Gallon to

Overflow

Whirlpool

Operating

Volume

Height to

Underside

of Deck: C

Dimensions

L-W-H



753737-100 Rev. C

DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE

OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z1.1 AND A11.1.7.

ROUGHING-IN REFERENCES

5' x 32" (MODEL 2422L / LA / V / VA)

CUT OUT IN FLOOR

FOR DRAIN

0"

(15mm)

3"

(13mm)

7-1/"

(11mm)

10-1/"

(7mm)

(7mm)

-7/"

(73mm)

"

(15mm)

13-1/"

(33mm)

1"

(0mm)

5' x 32" IA-LHO (MODEL 2425L/V-LHO) - shown

5' x 32" IA-RHO (MODEL 2425L/V-RHO)

0"

(15mm)

3"

(1mm)

(7mm)

7-1/"

(11mm)

"

(15mm)

11"

(7mm)

13-3/"

(3mm)

CUT OUT IN FLOOR

FOR DRAIN

5' x 36" (MODEL 2771L / LA / V / VA)

7"

(1mm)

3"

(1mm)

7-3/"

(17mm)

11"

(7mm)

3-1/"

(3mm)

(7mm)

"

(15mm)

13-3/"

(3mm)

CUT OUT IN FLOOR

FOR DRAIN

6' x 36" (MODEL 7236L / LA / V / VA)

"

(17mm)

5-3/"

(137mm)

"

(15mm)

3"

(1mm)

-1/"

(10mm)

(7mm)

11-1/"

(mm)

1-3/"

(mm)

1"

(57mm)

CUT OUT IN FLOOR

FOR DRAIN

OVAL (MODEL 2645L / LA / V / VA)

0"

(15mm)

3"

(13mm)

11"

(7mm)

7-3/"

(17mm)

13-3/"

(3mm)

"

(15mm)

(7mm)

3-1/"

(3mm)

CUT OUT IN FLOOR

FOR DRAIN

3-1/"

(3mm)

753737-100 Rev. C

DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE

OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.

ROUGHING-IN REFERENCES

SAVONA (MODEL 2901L)

CORNER (MODEL 6060L / V)

(178mm)

76-3/4"

(1949mm)

54-1/2"

(1384mm)

65-3/8"

(1661mm)

(76mm)

7" (178mm)

15"

(381mm)

5-5/8"

(143mm)

17-3/4"

(451mm)

10"

(254mm)

13-3/4" (349mm)

CUT OUT

IN FLOOR FOR DRAIN

72"

(1829mm)

44"

(1118mm)

(76mm)

(305mm)

(203mm)

RECOMMENDED FITTING LOCATION

64 X 279mm (2-1/2 X 11)

●

(152mm)

11-1/2"

(292mm)

5-1/2"

(140mm)

CADET CORNER (MODEL 2775L)

(60

)

70mm REF.

(2-3/4)

165mm

(6-1/2)

279mm

(11

)

229 X 305mm

X 12

)

CUTOUT IN

FLOOR FOR

DRAIN

OUTLINE OF

CUTOUT

2159mm

(85

)

1080 mm

(42-1/2

)

C/L

1524mm

(60

)

1076mm

(42-3/8

)

1080mm

(42-1/2

)

PUMP

C/L OF DRAIN OUTLET

5X42 (MODEL 2805L)

1524mm

(60

)

INTEGRAL

FITTING DECK

762mm

(30

)

1067mm

(42

)

PROVIDE ACCESS

TO PUMP FOR

SERVICE ON ALL

INSTALLATIONS

C/L OF

DRAIN

19mm

(3/4

)

PUMP

305mm

(12

)

152mm

)

PROVIDE ACCESS TO

PUMP FOR

SERVICING ON ALL

INSTALLATIONS

RECOMMENDED

FITTING

LOCATION

64 X 330mm

(2-1/2 X 13

)

OUTLINE OF CUTOUT

1486mm x 1029mm

(58-1/2

x 40-1/2

)

178mm x 381mm

x 15

)

FLOOR

CUTOUT

ELLISSE (MODEL 2711L)

1829mm

(72

)

927mm

(36-1/2

)

OUTLINE OF CUTOUT

1791 X 1181

(70-1/2

X 46-1/2

)

C/L OF

DRAIN

102mm

)

PUMP

305mm

(12

)

1219mm

(48

)

229mm x 356mm

x 14

) FLOOR

CUTOUT

RECOMMENDED

FITTING LOCATION

64 X 279mm (2-1/2" X 11")

OPTIONAL DECK

FITTING AREA

GRAB BAR

FITTING AREA

PROVIDE ACCESS TO

PUMP FOR SERVICE

ON ALL INSTALLATIONS



753737-100 Rev. C

REMINISCENCE (MODEL 2908L / LA)

 x 305mm

( X 1)

FLOOR

CUTOUT

mm REF.

(-1/)

17mm

(")

PUMP

1mm

(3")

57mm

(1)

330mm

(13

)

INTEGRAL

FITTING

DECK

15mm

()

OUTLINE OF

CUTOUT

C/L OF DRAIN

OUTLET

PROVIDE ACCESS TO

PUMP FOR SERVICE

ON ALL INSTALLATIONS

CADET 6 x 36 (MODEL 2773L)

RECOMMENDED FITTING LOCATION

 X 330mm (-1/ x 13")

FOR PIER OR ISLAND

INSTALLATIONS ONLY

ALT. FITTING

LOCATION #1

1 mm

(7)

0 mm

(35-3/)

OUTLINE OF CUTOUT

171 mm x 70 mm

(70-1/ X 3-1/)

5 mm

(17-7/)

mm

()

305 mm

(1)

57mm

(-1/)

() JETS

CUTOUT IN FLOOR

FOR DRAIN

PUMP

FINISHED

WALL

1 mm

(3/)

 mm

()

C/L OF DRAIN

() AIR VALVES

PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS

CADET 6 x 42 (MODEL 2774L / LA)

C/L OF DRAIN

RECOMMENDED FITTING LOCATION

 X 330mm (-1/ x 13")

FOR PIER OR ISLAND

INSTALLATIONS ONLY

ALT. FITTING

LOCATION #1

1 mm

(7)

107mm

()

533mm

(1)

mm

()

305 mm

(1)

57mm

(-1/)

() JETS

CUTOUT IN FLOOR

FOR DRAIN

PUMP

FINISHED

WALL

1 mm

(3/)

 mm

()

() AIR VALVES

PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS

OUTLINE OF

CUTOUT

171mm x 10mm

(70-1/ X 0-1/)

DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE

OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z1.1 AND A11.1.7.

ROUGHING-IN REFERENCES

753737-100 Rev. C



INSTALLATION AND FRAMING INSTRUCTIONS

The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs as needed. Ensure

roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an access opening for servicing the pump

and controls. It is strongly recommended that an additional opening be provided for access to the drain components. The apron should not be used

as the primary access opening.

TYPICAL PIER TYPE INSTALLATION

AS DESIRED

CUTOUT

AS DESIRED

CUTOUT



(10 mm)

1

(305 mm)

MOUNTING

SURFACE

WATERPROOF

SEALANT

BATH

TYPICAL RECESS INSTALLATION



(10 mm)

1

(305 mm)

LEVELING

STRINGERS

TILE

BEAD

STRIP

LEVELING STRINGER

1 x  (not for support)

BATH

ADHESIVE

SEALANT

WALLBOARD

NOTE: Tile bead kit not included and

must be purchased separately.

TYPICAL INSTALLATION

FIGURE 1

This bath must be supported along its entire bottom. Use mortar as bedding

material (do not use sand or foam). Apply enough mortar to support the complete

bottom of the bath. After the mortar has been poured, and before it sets, position

whirlpool or bath within recess until the rim is leveled against the leveling stringers (see

"Typical Recess Installation") shown below.

The rim of the bath must not support weight. Allow the mortar material to completely

harden before applying weight to the rim or bottom of the bath. Any finish material such

as tile or wall board must be self-supporting if it contacts the deck of the bath.

Replace whirlpool and re-shim the integral support feet, shimming the entire length of

the support feet. Secure the shims using construction adhesive, silicone, mortar or

equivalent materials. While not a necessity, the use of a foundation base consisting of

cement, mortar, or grout will help provide a solid and secure installation.

3. Install drain components to the whirlpool following the drain installation instructions. Before

replacing your whirlpool for final installation, be certain that an opening has been provided in

the sub-floor for the drain. See the roughing-in drawing and Table 1 for suggested opening

size (shadowed) and location dimensions. The drain/overflow of the bath extends below the

bottom of the bath. Note that this requires a cutout in the floor.

The floor structure beneath the bath must be able to support a total weight of bath, water, and

bather. Refer to Table 1 under total weight for your model.

For Models:

2425L/V-LHO and 2425L/V-RHO;

For Models:

2645L/V, 2771L/V, 6060L/V, 7236L/V, 2422L/V and 2422LA/VA;

. Remove the whirlpool and attach a 1 x  stringer to the studs, with the top of the stringer touching the traced line.

The rim of the bath must not support weight.

1. Position the whirlpool into the installation opening and level the deck in both directions, shimming the integral support feet IF necessary.

Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1).

ACCESS PANEL MUST BE LOCATED

ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON PUMP/MOTOR

END FOR SERVICE.

ACCESS PANEL MUST BE LOCATED

ON THE SAME SIDE AS THE MOTOR.

ALLOW OPEN FRAMING ON

PUMP/MOTOR END FOR SERVICE.

FOR E & D DIMENSIONS SEE TABLE 1 ON PAGE 5.

FOR G & F DIMENSIONS SEE TABLE 1 ON PAGE 5.

NOTE:

FRONT EDGE

OF BATH MUST

BE SUPPORTED

BY STUD WALL OR

AMERICAN STANDARD

APRON KIT

The rim of the bath must not support weight. If foundation base is used, allow the

bedding material to completely harden before applying weight to the rim or bottom of

the bath. Any finish material such as tile or wall board must be self-supporting if it

contacts the deck of the bath.

UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)

IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.

(EXCEPT 2425 WHERE APRON IS PRIMARY ACCESS OPENING)

ACCESS PANELS NOT REQUIRED

FOR BATH TUBS.

ACCESS PANELS NOT REQUIRED

FOR BATH TUBS.

753737-100 Rev. C

SUGGESTED WHIRLPOOL / BATH

INSTALLATION METHOD

SECURE THE BATH TO THE STUDS AS SHOWN

FOR WOOD OR STEEL STUD CONSTRUCTION.

TYPICAL FLANGE MOUNTING DETAIL

UNLESS AN ACCESS OPENING OF AT LEAST

12" x 24" (305 x 610mm) IS PROVIDED,

WARRANTY SERVICE WILL NOT BE PERFORMED.

1-1/

(5mm)

WHIRLPOOL

ACCESS PANEL

Please note that care must be taken to protect the surface of the tub during all aspects of the installation.

Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result.

1. Install the tub per the installation instructions provided with the unit.

. Prepare the bath deck support structure per the local codes. Note - the bath deck must be self supporting.

3. Cut bath deck to your specifications.

. Place the bath deck in position and trace the opening on the tub with a soft pencil. Do not drill or cut the bath

deck with the tub directly beneath it as damage to the tub may result.

5. Remove the bath deck and apply a generous bead of waterproof sealant on the outer edge of the traced line.

. Replace the bath deck and secure it into place.

7. Apply additional sealant along the tub and bath deck interface as necessary to ensure a watertight seal.

. Remove excess sealant per the manufacturer's instructions.

Finished bath deck surface material must be

self-supporting and secured per local codes

Tub support structure per installation

instructions provided with the tub

Bath deck support material

Bathtub

Waterproof

Sealant

* SEE CUTOUT TEMPLATE

PROVIDED ON UNDERSIDE

OF BOX LID

UNDER DECK MOUNTING INSTRUCTIONS

STUD

WATERPROOF DRYWALL

OR CEMENT BOARD

WATERPROOF DRYWALL

OR CEMENT BOARD

TILE

SEALANT

TUB

ROOFING NAIL

1 x 3 (5 x 7mm) WOOD

STRINGER FULL LENGTH

1 x 3 (5 x 7mm) WOOD

STRINGER FULL LENGTH

STEEL

STUD

WASHER

TILE

SEALANT

TUB

" (10mm)

DRYWALL

SCREW

WOOD

STUDS

STEEL

STUDS

TYPICAL INSTALLATION -

CORNER

753737-100 Rev. C

All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes.

WARNING: When using electrical products, basic precautions should always be observed, including the following:

1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter.

. Grounding is required. The unit should be installed by a licensed electrician and grounded.

3. Permit access for servicing motor as noted.

. All building materials and wiring should be routed away from the pump body and heater (if equipped).

WHIRLPOOL ELECTRICAL INSTALLATION INSTRUCTIONS

ELECTRICAL DIAGRAM

READ AND FOLLOW ALL INSTRUCTIONS

BLACK

WHITE

120 VA C

GND .

PUMP/MOTOR

WIRE SELEC TION GUIDE

Maxim um di stanc e fro m

fuseb ox to moto r

The s izes shown on t his

chart are recom menda tions

for c opper cond uctor s

only. Alw ays f ollow

local and natio nal

elect rical code s

Motor

Hi Pe rform ance

Ratin g

2.1 H .P.,

1.4 H .P.,

and 1 .25 H .P.

50' 100'

115V Power Line

150' 20 0 '

12 10 8 8

The whirlpool should be installed on a 120 vac,

amp dedicated

GFCI circuit.

The circuit should be hard-wired from the electrical power supply panel. The

circuit must be a three (3) wire circuit from the electrical supply panel. A

grounded neutral wire and a third wire, earth ground, are essential.

Optional heater requires a separate 15 amp maximum GFCI circuit.

The whirlpool should be installed on a 120 vac, 20 amp dedicated

GFCI circuit.

The circuit should be hard-wired from the electrical power supply panel. The

circuit must be a three (3) wire circuit from the electrical supply panel. A

grounded neutral wire and a third wire, earth ground, are essential.

Optional heater requires a separate 15 amp maximum GFCI circuit.

GFCI CIRCUIT REQUIREMENTS: FOR MODEL NUMBERS:

2422, 2425, 2645,

2771, 2805, 2908

ALL MODELS

7236, 2774

MODELS ENDING IN SUFFIX

LA, LAC, VA, VAC

6060, 2775, 2773, 2711, 2901

ALL MODELS

7236, 2774

MODELS ENDING IN SUFFIX

L, LC, V, VC

PLEASE SEE THE FOLLOWING TABLE FOR GFCI CIRCUIT REQUIREMENTS:

1

753737-100 Rev. C

For 6060L/V Corner Only

OPERATION

ELECTRICAL CONNECTIONS

Install a separate 10VAC / 15AMP dedicated circuit with GFCI (Ground Fault Circuit Interrupter) protection.

At initial start-up with power ON, push the GFCI test button. The reset button should pop out. Push this button in to reset. If the GFCI fails to

operate in this manner, there is a ground fault or malfunction, indicating the possibility of electrical shock. Turn off the power and do not

use the bath until the source of the problem has been identified and corrected.

1. Route two separate branch circuits to the junction box near the whirlpool as shown in Figure . Each branch circuit MUST BE GFCI

PROTECTED and must use copper conductors only.

. Ensure the heater and pump are properly GROUNDED and BONDED as required. Attach the  AWG solid copper conductor supplied with

the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3. The conductor is secured to the lugs using set

screws. The motor frame shall have a second  AWG solid copper conductor connected from the frame bonding lug to the homes electrical

panel or approved local bonding point as shown in Figure 3.

Fig. 2 Fig. 3

Fig. 1

WARNING: Prior to operation, review the Important Safety Instructions

listed at the beginning of this instruction manual.

Once the heater is installed and the whirlpool pump is operating, the heater is

totally automatic. The heater will help maintain the temperature of the water in

the bath.

Pressure Switch

The heater is equipped with a preset pressure switch. The pump must be

running with water flowing in the whirlpool to allow the heater to turn on.

Indicator Light

This light turns on whenever the heater is operating.

High-Limit Switch

The heater includes an exclusive "Intelligent High-Limit". This safety circuit will not "false trip" from hot tap water. It will only turn the heater

off if the thermostat fails. If the high-limit trips frequently, call a service technician.

To manually reset the circuit in the event that the “High-Limit” switch has been activated, simply (1) Turn off the whirlpool pump. () Drain

water from the tub. (3) Remove power from heater by unplugging at receptacle or turning off circuit breaker. () The heater circuit will

automatically reset in less than 15 minutes. (5) Restore power to the heater. () Whirlpool bath is now ready to use.

ELECTRICAL DIAGRAM

READ AND FOLLOW ALL INSTRUCTIONS

BL AC K

WH IT E

12 0 VA C

GN D.

SEPARATE 20 AMP GFCI OUTLET

for2.1 H.P. PUMP

SEPARATE 15 AMP GFCI OUTLET

for 1.6 H.P. PUMP

PUMP/MOTOR

ELECTRICAL INSTALLATION

HEATER

BL AC K

WH IT E

12 0 VA C

GN D.

SEPARATE

15 AMP GFCI OUTLET

HEATER “ON” LIGHT

Bonding Lug on

Heater Housing

E-Z INST

™

WHIRLPOOL

HEA

RUN  AWG SOLID COPPER

CONDUCTORS FROM

HEATER BONDING LUG TO

PUMP/MOTOR FRAME LUG

AND FROM PUMP/MOTOR

LUG TO APPROVED

GROUND AS SHOWN

(PUMP/MOTOR)

TO GROUND

SECOND

COPPER

CONDUCTOR

FIRST COPPER

CONDUCTOR

PUMP/MOTOR FRAME WITH

BONDING LUGS

HEATER ON

E-

™

FACTORY INSTALLED - NOT FOR RESALE

HEATER P/N: 753174-100

(HEATER)

753737-100 Rev. C

DRAIN CONNECTION AND SYSTEM TEST

Using recommended drain assembly, connect whirlpool drain to waste line in accordance with the drain assembly instructions.

Tighten all drain joints securely. Check the pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with

water to a point " above the top of the highest jet. Recheck the pump couplings and make certain that they are not leaking.

(Although the pump couplings are factory tightened and inspected, some loosening may have occurred during transit.) Make sure

the whirlpool is connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the

whirlpool is running.

POST INSTALLATION CLEAN-UP

Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use

wire brushes or any other metal implement on bath surface.

Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains

may be removed using granular Spic and Span

mixed with water.

Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.

AFTERCARE and CLEANING

• The high gloss surface is resistant to impact and chemicals and will retain its lasting luster with proper care and

maintenance.

• Always fill the tub with temperate water. Excessively hot water may cause surface damage

• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.

• Clean after use with a mild liquid household detergent cleaner. Do not use Lestoil, Lysol Disinfectant (spray or

concentrate), or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner, or

cleaning products in aerosol cans.

HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.

• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits,or other surface blemishes.

• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses

its sheen, dulled areas can be restored by rubbing with a white "automotive type" polishing compound and

waxing with a "liquid wax."

• Do not wax areas where you walk or stand.

• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into

contact with the surface.

• Clean the surrounding surface immediately after using caustic drain cleaners.

• Burning cigarettes will damage the surface.

• Should damage to the fixture occur, repairs can be made quickly and easily.

Your distributor or builder can provide details.

• Do not permit drain cleaner to enter the circulation system.

CIRCULATION SYSTEM CLEANING-PURGING PROCEDURES

STEP 1. Once every month purge and clean the circulating system. Fill whirlpool with warm water and add two teaspoons

of dishwasher detergent and one-half cup of house hold bleach.

STEP 2. Activate whirlpool system in accordance with operating instructions or two minutes.

STEP 3. Drain and refill whirlpool with cool water and circulate for additional five minutes.

STEP 4. Drain whirlpool completely.

1

753737-100 Rev. C

By Mail: American Standard Inc.

P.O. Box 5

West Caldwell, N.J. 07007

Attention: Customer Care Center

AS AMERICA, INC. (AMERICAN STANDARD) LIMITED LIFETIME WARRANTY

FOR LIFETIME™ / EVOLUTION™ ACRYLIC WHIRLPOOLS

AS America (“American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this whirlpool or any

of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long

as it is owned by the original consumer purchaser.

This warranty shall only become effective upon receipt by American Standard of a completely filled out Warranty Registration Card evidencing

proof of purchase.

THIS WARRANTY SHALL BE VOID IF THE ACCESS PANEL TO THE WHIRLPOOL IS COVERED IN ANY MANNER CONTRARY TO THE

INSTALLATION INSTRUCTIONS. In no event will American Standard be liable for the cost of repair or replacement of any installation

materials including but not limited to tiles, marble etc.

This limited warranty DOES NOT COVER the following:

1. Defects or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenance and cleaning as

directed in the owner’s manual and use of other than genuine American Standard replacement parts, in all cases whether caused by a

plumbing contractor, service company, the owner or any other person.

. Deterioration through normal wear and tear and the expense of normal maintenance.

3. Commercial application.

. Options and accessories. American Standard’s limited warranty on these items is one year for parts only and excludes labor. This one

year limited warranty covers accessories manufactured by American Standard (e.g. aprons, drains, grab bars, heaters, trim kits) against

defects of material or workmanship. Warranty coverage begins on the date the accessory was originally purchased by the owner.

5. Postage or shipping costs for returning products for repairs or replacement under this limited warranty and labor or other costs incurred in

connection with product removal or installation under this limited warranty.

. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY EXPRESSLY DISCLAIMED, OR

THE EXTENSION BEYOND THE DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING THOSE OF

MERCHANTABILITY OR FITNESS FOR AN INTENDED PURPOSE. (Some jurisdictions do not allow limitations on how long an implied

warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you.)

7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly distributors, retailers, dealers,

installation contractors and users of plumbing products should determine whether there are any code restrictions on the installation or use of a

specific product.)

This warranty gives you specific legal rights. You may have other legal rights that vary from state to state. For service under this warranty, you

should contact the following:

By Telephone:

1-800-442-1902

If inspection of this AS American, Inc. (“American Standard”) plumbing product, within one year after its initial purchase, confirms that it is

defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.

This warranty applies only to the original purchaser and installation of these products.

This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this

product should check with a local building or plumbing contractor to insure local code compliance before installation.

This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance,

abuse, misuse, accident or other damages; if it was not installed in accordance with American Standard's instructions; or if it has been

modified in a manner inconsistent with the product as shipped by American Standard.

American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or

installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product

defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or

provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in

which case this warranty does not affect such statutory rights.

For service under these warranties, it is suggested that a claim be made through the contractor or dealer from or through whom the product

was purchased, or that a service request (including a description of the product model and of the defect) be sent to:

AS AMERICA, INC. (AMERICAN STANDARD) ONE YEAR LIMITED WARRANTY

FOR E-Z INSTALL WHIRLPOOL HEATER

Product names listed herein are trademarks of AS America, Inc.

HOTLINE FOR HELP

For toll-free information and answers to your questions, call 1 (800) 442-1902

weekdays: :00 a.m. to 5:00 p.m. Eastern Time

SERVICE: For service or repair contact the number below. The model number and

serial number for your whirlpool are located on a label near the motor.

By Mail: American Standard Inc.

P.O. Box 5

West Caldwell, N.J. 07007

Attention: Customer Care Center

By Telephone:

1-800-442-1902

753782-100 Rev. B

-JGFUJNF&WPMVUJPO

8IJSMQPPMBOE#BUIT0QFSBUJOHBOE6TFS

.BJOUFOBODF*OTUSVDUJPO.BOVBM

T hank you for choosing

American Standard

"MMJOGPSNBUJPOJOUIJTNBOVBMJTCBTFEPOUIFMBUFTUQSPEVDUJOGPSNBUJPOBWBJMBCMFBUUIFUJNFPGQVCMJDBUJPO"4"NFSJDBT*OD

SFTFSWFTUIFSJHIUUPNBLFDIBOHFTJOQSPEVDUDIBSBDUFSJTUJDTQBDLBHJOHPSBWBJMBCJMJUZBUBOZUJNFXJUIPVUOPUJDF

1SPEVDUOBNFTMJTUFEIFSFJOBSFUSBEFNBSLTPG"4"NFSJDBT*OD

¥"4"NFSJDBT*OD

"55&/5*0/*/45"--&3

1MFBTFEFMJWFSUIJTNBOVBMUPIPNFPXOFS

753782-100 Rev. B



4"7&5)&4&*/4536$5*0/4

8"3/*/(3JTLPGQFSTPOBMJOKVSZ%POPUQFSNJUDIJMESFOUPVTFUIJTVOJUXJUIPVUBEVMUTVQFSWJTJPO

8"3/*/(3JTLPGQFSTPOBMJOKVSZ%POPUPQFSBUFUIJTVOJUXJUIPVUUIFHVBSEPWFSUIFTVDUJPOGJUUJOH

8"3/*/(3JTLPGFMFDUSJDTIPDL%POPUQFSNJUFMFDUSJDBMBQQMJBODFTIBJSESZFSUFMFQIPOFSBEJPFUDXJUIJO

JODIFTNNPGUIJTVOJU

8"3/*/(3JTLPGIZQFSUIFSNJBBOEQPTTJCMFESPXOJOH1FPQMFVTJOHNFEJDBUJPOTBOEPSIBWJOHBEWFSTF

NFEJDBMIJTUPSZTIPVMEDPOTVMUBQIZTJDJBOCFGPSFVTJOHUIJTQSPEVDU

8"3/*/(3JTLPGQFSTPOBMJOKVSZ%POPUPWFSGJMMVOJUCFGPSFFOUFSJOH&OUFSJOHUVCXIFOGJMMFENPSFUIBO

DBODBVTFPWFSGMPXBOETMJQQFSZDPOEJUJPOT&YFSDJTFDBVUJPOXIFOFOUFSJOHBOEFYJUJOH

8"3/*/(/P'PPEPS"MDPIPMJD#FWFSBHFT6TFPGZPVSCBUIUVCJNNFEJBUFMZBGUFSNFBMTJTOPU

SFDPNNFOEFE"WPJEBMDPIPMDPOTVNQUJPOCFGPSFPSEVSJOHCBUIJOH"MDPIPMJDCFWFSBHFTDBODBVTFESPXTJOFTTPS

IZQFSUIFSNJBSFTVMUJOHJOMPTTPGDPOTDJPVTOFTTPSFWFOESPXOJOH

8"3/*/(1SFHOBODZ*GZPVBSFPSUIJOLZPVNBZCFQSFHOBOUDPOTVMUZPVSQIZTJDJBOCFGPSFVTJOHUIFCBUIUVC

/FWFSESPQPSJOTFSUBOZPCKFDUJOUPBOZPQFOJOH

6TFUIJTVOJUPOMZGPSJUTJOUFOEFEVTFBTEFTDSJCFEJOUIJTNBOVBM%POPUVTFBOZBUUBDINFOUTOPUSFDPNNFOEFECZ

"NFSJDBO4UBOEBSE

5IFVOJUNVTUCFDPOOFDUFEPOMZUPBTVQQMZDJSDVJUUIBUJTQSPQFSMZQSPUFDUFECZBHSPVOEGBVMUDJSDVJUJOUFSSVQUFS

('$*4VDIB('$*TIPVMECFQSPWJEFECZUIFJOTUBMMFSBOETIPVMECFUFTUFEPOBSPVUJOFCBTJT5PUFTUUIF('$*

QVTIUIFUFTUCVUUPO5IF('$*TIPVMEJOUFSSVQUQPXFS1VTIUIFSFTFUCVUUPO1PXFSTIPVMECFSFTUPSFE*GUIF('$*

GBJMTUPPQFSBUFJOUIJTNBOOFSUIF('$*JTEFGFDUJWF*GUIF('$*JOUFSSVQUTQPXFSUPUIFCBUIUVCXJUIPVUUIFUFTUCVUUPO

CFJOHQVTIFEBHSPVOEDVSSFOUJTGMPXJOHJOEJDBUJOHUIFQPTTJCJMJUZPGBOFMFDUSJDTIPDL%POPUVTFUIJTIZESPNBTTBHF

CBUIUVC%JTDPOOFDUUIFIZESPNBTTBHFCBUIUVCBOEIBWFUIFQSPCMFNDPSSFDUFECZBMJDFOTFEFMFDUSJDJBOCFGPSFVTJOH

"QSFTTVSFXJSFDPOOFDUPSJTQSPWJEFEPOUIFFYUFSJPSPGUIFNPUPSVOJUUPQFSNJUDPOOFDUJPOPGBOP"8(TPMJE

DPQQFSCPOEJOHDPOEVDUPSCFUXFFOUIJTVOJUBOEBMMPUIFSFMFDUSJDBMFRVJQNFOUBOEFYQPTFENFUBMJOUIFWJDJOJUZBT

OFFEFEUPDPNQMZXJUIMPDBMSFRVJSFNFOUT5PSFEVDFUIFSJTLPGBOFMFDUSJDTIPDLDPOOFDUUIJTDPOOFDUPSUIF

HSPVOEJOHUFSNJOBMPGZPVSFMFDUSJDTFSWJDFPSTVQQMZQBOFMXJUIBDPOEVDUPSFRVJWBMFOUJOTJ[FUPUIFDJSDVJUDPOEVDUPST

TVQQMZJOHUIJTVOJU

*.1035"/54"'&5:

*/4536$5*0/4

*/4536$5*0/41&35"*/*/(50

"3*4,0''*3&&-&$53*$4)0$,

03*/+63:501&340/4

3&"%"/%'0--08"--*/4536$5*0/4

753782-100 Rev. B

0QFSBUJPO

/05&&BDIXIJSMQPPMJTTIJQQFEGSPNUIFGBDUPSZXJUIBOBJSBDUVBUPSPOPGGTXJUDIBOEQVNQXJUIBUUBDIFE

QPXFSTVQQMZDPSE01&3"5*/(5)&4:45&.8*5)0658"5&3%3:36//*/(8*--$"64&16.1

%"."(&"/%70*%5)&8"33"/5:"MXBZTGJMMUIFXIJSMQPPMCFGPSFPQFSBUJOHUIFQVNQ5IFBJSTXJUDIJT

NPVOUFEFJUIFSPOUIFEFDLPSTJEFXBMMPGUIFUVC

'JMMUIF8IJSMQPPM8BUFSMFWFMNVTUCFBUMFBTUPOFJODINNBCPWFUIFIJHIFTUKFUGPSQSPQFSPQFSBUJPO

4FFEJBHSBNCFMPX

%POPUGJMMXIJSMQPPMNPSFUIBOGVMMQSJPSUPUIFVTFSDPNQMFUFMZJNNFSTJOHUIFNTFMWFTJOUPVOJU

4UBSU8IJSMQPPM1VTIPODFOUFSPGCVUUPO#VUUPOXJMMEFQSFTTBOEXIJSMQPPMXJMMTUBSU

4UPQ8IJSMQPPM%FQSFTTBOESFMFBTFCVUUPOBOEXIJSMQPPMXJMMTUPQ

065-&5.645#&

('$*1305&$5&%

BMMIFBUFSTSFRVJSFTFQBSBUF('$*

"*3"$56"50348*5$)

MPDBUJPOWBSJFTXJUINPEFM

"*356#*/(

8"5&3-&7&-

-7JODMVEFTGBDUPSZJOTUBMMFEIFBUFS

"JS7PMVNF$POUSPM"EKVTUNFOUT8BUFSUVSCVMFODFJTEFUFSNJOFECZUIFBNPVOUPGBJSNJYFEXJUIUIF

XBUFS3PUBUFUIFBJSWPMVNFDPOUSPMDPVOUFSDMPDLXJTFGPSNPSFUVSCVMFODFDMPDLXJTFGPSMFTT

4"'&5)&"5&3

3&.07"#-&#-"/,









"JS7PMVNF$POUSPM"EKVTUNFOUT

.03&"*3 -&44"*3





753782-100 Rev. B

"EKVTUBCMF'MPX$PNGPSU+FU5IFXBUFSGMPXBDUJPONBZCFBEKVTUFEGSPNWJHPSPVTUPTPGUCZSPUBUJOHUIF

OP[[MFDPVOUFSDMPDLXJTFGPSWJHPSPVTBOEDMPDLXJTFGPSTPGU



/05&:PVNBZCBMBODFUIFBJSWPMVNFDPOUSPMBOEOP[[MFBEKVTUNFOUGPSUIFNPTUEFTJSBCMFDPOEJUJPO

4NBMM+FU

-BSHF+FU

4PGUFS.BTTBHF

DPVOUFSDMPDLXJTF

.PSF7JHPSPVT.BTTBHF

DMPDLXJTF

4PGUFS.BTTBHF

DPVOUFSDMPDLXJTF

.PSF7JHPSPVT.BTTBHF

DMPDLXJTF

-JGFUJNF%SBJO.PEFMSFRVJSFEPO.PEFMT--"77"--"77"

-7--"77"

0WFSGMPX

1BSUJBMMZGJMMUVCUIFOFOUFSUVCCFGPSFDPNQMFUFMZGJMMJOHUPQSFWFOUPWFSGMPX

5JQ5PF%SBJO

%FQSFTTESBJODBQUPPQFOPSDMPTFESBJO

"DDFTT1BOFM.PEFM-7

3FNPWFBDDFTTQBOFMUPTFSWJDFNPUPS

"DDFTT1BOFM

5JQ5PF%SBJO

0WFSGMPX

753782-100 Rev. B

0QUJPOBM*O-JOF&;*OTUBMM)FBUFS0QFSBUJOH*OTUSVDUJPOT

4PNFXIJSMQPPMTBSFFRVJQQFEGPSVTFXJUIUIFPQUJPOBM&;*OTUBMM)FBUFS8IJSMQPPM#BUI)FBUFSQBSUOP4JNQMZ

MPDBUFUIF&;*OTUBMM)FBUFS3FNPWBCMF#MBOLOFBSUIFXIJSMQPPMQVNQBOESFQMBDFJUXJUIUIFIFBUFS#FTVSFUP'0--08

"--01&3"5*/(*/45"--"5*0/BOE4"'&5:*/4536$5*0/45)"5$0.&8*5):063&;*/45"--)&"5&3

$"3&'6--:#&'03&130$&&%*/(8*5)5)&*/45"--"5*0/5IFIFBUFSXJMMNBJOUBJOUIFUFNQFSBUVSFPGUIFXBUFS

JOUIFXIJSMQPPMPSJODSFBTFUIFUFNQFSBUVSFPGUIFXBUFSJOUIFXIJSMQPPMBUBCPVUUXPUPGPVSEFHSFFT'BISFOIFJUQFSIPVS

VQUPBNBYJNVNPG'5IFIFBUFSJODMVEFTUIFGPMMPXJOHDPNQPOFOUT

5IFSNPTUBU

5IF4NBSU5IFSNPTUBUSFRVJSFTOPBEKVTUNFOUBOEXJMMBVUPNBUJDBMMZNBJOUBJOUIFXBUFSUFNQFSBUVSFBU'BISFOIFJU

*GUIFCBUIUVCJTUPPXBSNTJNQMZBEKVTUCZBEEJOHDPMEXBUFS4FF*NQPSUBOU4BGFUZ*OTUSVDUJPOTTVQQMJFEXJUIIFBUFS

)JHI-JNJU

5IFIFBUFSJODMVEFTBOFYDMVTJWFi*OUFMMJHFOU)JHI-JNJUu5IJTTBGFUZDJSDVJUXJMMOPUiGBMTFUSJQuGSPNIPUUBQXBUFS*UXJMMPOMZ

UVSOUIFIFBUFSPGGJGUIFUIFSNPTUBUGBJMT*GUIFIJHIMJNJUUSJQTGSFRVFOUMZDBMMBTFSWJDFUFDIOJDJBO

5PNBOVBMMZSFTFUUIFDJSDVJUJOUIFFWFOUUIBUUIFi)JHI-JNJUuTXJUDIIBTCFFOBDUJWBUFETJNQMZ

5VSOPGGUIFXIJSMQPPMQVNQ

%SBJOXBUFSGSPNUIFUVC

3FNPWFQPXFSGSPNIFBUFSCZVOQMVHHJOHBUSFDFQUBDMFPSUVSOJOHPGGDJSDVJUCSFBLFS

5IFIFBUFSDJSDVJUXJMMBVUPNBUJDBMMZSFTFUJOMFTTUIBONJOVUFT

3FTUPSFQPXFSUPUIFIFBUFS

8IJSMQPPMCBUIJTOPXSFBEZUPVTF

*OEJDBUPS-JHIU

5IFMJHIUUVSOTPOXIFOUIFIFBUFSJTPQFSBUJOH

1SFTTVSF4XJUDI

5IFIFBUFSJTFRVJQQFEXJUIBQSFTFUQSFTTVSFTXJUDI5IJTTXJUDIXJMMOPUBMMPXUIFIFBUFSUPUVSOPOJGUIFQVNQJTOPU

SVOOJOHXJUIXBUFSGMPXJOHUISPVHIUIFXIJSMQPPMQJQJOHTZTUFN

'PS-7$PSOFS0OMZ



01&3"5*0/

'JH

8"3/*/(1SJPSUPPQFSBUJPOSFWJFXUIF*NQPSUBOU4BGFUZ*OTUSVDUJPOT

MJTUFEBUUIFCFHJOOJOHPGUIJTJOTUSVDUJPONBOVBM

0ODFUIFIFBUFSJTJOTUBMMFEBOEUIFXIJSMQPPMQVNQJTPQFSBUJOHUIFIFBUFSJT

UPUBMMZBVUPNBUJD5IFIFBUFSXJMMIFMQNBJOUBJOUIFUFNQFSBUVSFPGUIFXBUFSJO

UIFCBUI

1SFTTVSF4XJUDI

5IFIFBUFSJTFRVJQQFEXJUIBQSFTFUQSFTTVSFTXJUDI5IFQVNQNVTUCF

SVOOJOHXJUIXBUFSGMPXJOHJOUIFXIJSMQPPMUPBMMPXUIFIFBUFSUPUVSOPO

*OEJDBUPS-JHIU

5IJTMJHIUUVSOTPOXIFOFWFSUIFIFBUFSJTPQFSBUJOH

)JHI-JNJU4XJUDI

5IFIFBUFSJODMVEFTBOFYDMVTJWF*OUFMMJHFOU)JHI-JNJU5IJTTBGFUZDJSDVJUXJMMOPUGBMTFUSJQGSPNIPUUBQXBUFS*UXJMMPOMZUVSOUIFIFBUFS

PGGJGUIFUIFSNPTUBUGBJMT*GUIFIJHIMJNJUUSJQTGSFRVFOUMZDBMMBTFSWJDFUFDIOJDJBO

5PNBOVBMMZSFTFUUIFDJSDVJUJOUIFFWFOUUIBUUIFi)JHI-JNJUuTXJUDIIBTCFFOBDUJWBUFETJNQMZ5VSOPGGUIFXIJSMQPPMQVNQ%SBJO

XBUFSGSPNUIFUVC3FNPWFQPXFSGSPNIFBUFSCZVOQMVHHJOHBUSFDFQUBDMFPSUVSOJOHPGGDJSDVJUCSFBLFS5IFIFBUFSDJSDVJUXJMM

BVUPNBUJDBMMZSFTFUJOMFTTUIBONJOVUFT3FTUPSFQPXFSUPUIFIFBUFS8IJSMQPPMCBUIJTOPXSFBEZUPVTF

HEATER “ON” LIGHT

Bonding Lug on

Heater Housing

E-Z INSTAL

™

WHIRLPOOL

HEATER

FACTORY INSTALLED - NOT FOR RESALE

HEATER P/N: 753174-100



753782-100 Rev. B

ELECTRICAL CONNECTIONS

Install a separate 120VAC / 15AMP dedicated circuit with GFCI (Ground Fault Circuit Interrupter) protection.

At initial start-up with power ON, push the GFCI test button. The reset button should pop out. Push this button in to reset. If the GFCI fails to

operate in this manner, there is a ground fault or malfunction, indicating the possibility of electrical shock. Turn off the power and do not

use the bath until the source of the problem has been identified and corrected.

1. Route two separate branch circuits to the junction box near the whirlpool as shown in Figure 2. Each branch circuit MUST BE GFCI

PROTECTED and must use copper conductors only.

2. Ensure the heater and pump are properly GROUNDED and BONDED as required. Attach the 8 AWG solid copper conductor supplied with

the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3. The conductor is secured to the lugs using set

screws. The motor frame shall have a second 8 AWG solid copper conductor connected from the frame bonding lug to the homes electrical

panel or approved local bonding point as shown in Figure 3.

Fig. 2 Fig. 3

ELECTRICAL DIAGRAM

READ AND FOLLOW ALL INSTRUCTIONS

BL AC K

WH IT E

12 0 VA C

GN D.

SEPARATE 20 AMP GFCI OUTLET

for2.1 H.P. PUMP

SEPARATE 15 AMP GFCI OUTLET

for 1.6 H.P. PUMP

PUMP/MOTOR

ELECTRICAL INSTALLATION

HEATER

BL AC K

WH IT E

12 0 VA C

GN D.

SEPARATE

15 AMP GFCI OUTLET

RUN 8 AWG SOLID COPPER

CONDUCTORS FROM

HEATER BONDING LUG TO

PUMP/MOTOR FRAME LUG

AND FROM PUMP/MOTOR

LUG TO APPROVED

GROUND AS SHOWN

(PUMP/MOTOR)

TO GROUND

SECOND

COPPER

CONDUCTOR

FIRST COPPER

CONDUCTOR

PUMP/MOTOR FRAME WITH

BONDING LUGS

HEATER ON

E-

™

(HEATER)

CLEANING AND MAINTENANCE:

• Always fill the tub with temperate water. Excessively hot water (greater than 130˚ F) may cause surface damage.

• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.

• Clean after use with a mild liquid household detergent cleaner. Do not turn on jets when such cleaners are present.

Do not use: Lestoil® Cleaner; Lysol® Disinfectant (spray or concentrate); or Lysol® Basin, Tub and Tile Cleaner;

Windex® Cleaner; Mr. Clean® Cleaner; Dow® Disinfectant Bathroom Cleaner*; or other cleaning products in aerosol cans.

• No Soap or Oils: Do not operate the whirlpool circulation system when using soap, bath oil or a bubble bath, or if such

substances are in solution in the bathwater. If introduced into the circulation system, they are likely to cause excessive

foaming. Bathe with soap or oil only when whirlpool circulation system is off. Drain whirlpool after each use.

Your American Standard whirlpool is designed to give you many years of pleasure with reasonable

care and maintenance.

Your new acrylic bathtub is tough, durable and easy to care for. The colors have been formulated to match

other American Standard fixtures and enhance your choice of bathroom decorations. The high gloss surface

will retain its lasting luster with proper care and maintenance.

Page is loading ...

American Standard 2771L.020 User manual

Brand: American Standard

Model: 2771L.020

Category: Space heaters

Type: User manual

Download PDF

report

American Standard 2771L.020 User manual

American Standard 2771L.020 User manual

Related papers

Other documents