Alto-Shaam 500-1D Owner's manual
- Category
- Food warmers
- Type
- Owner's manual
M N - 2 9 7 4 2 ( R e v . 6 ) • 0 2 / 1 6
p r i n t e d i n u . s . a .
Models:
500-1D, 1DN
500-2D, 2DN
500-3D, 3DN
500-1DN
500-2DN
500-3DN
500-1D
500-2D
500-3D
Drawer Warmers
MN-29742 (Rev. 6) 02/16 • Drawer Warmers
Delivery ...................................1
Unpacking .................................1
Safety Procedures and Precautions ............. 2-3
Installation
Installation Requirements ....................4
Clearance Requirements .....................4
Weights .................................4
Product Capacity ..........................4
500-1D, 2D, 3D
Cutout Dimensions .......................5
Dimension Drawing ......................5
Options and Accessories ..................5
500-1DN, 2DN, 3DN
Cutout Dimensions .......................6
Dimension Drawing .......................6
Options and Accessories ..................6
Electrical Specifications .....................7
Operating Instructions
User Information ..........................8
Before Initial Use ..........................8
Heating Characteristics .....................8
Food Product Tips .........................8
Operation ................................9
General Holding Guidelines .................10
Care and Cleaning
Cleaning and Preventative Maintenance ........11
Protecting Stainless Steel Surfaces ...........11
Cleaning Agents ..........................11
Cleaning Materials ........................11
Care and Cleaning ........................12
Food Safety
Food Safety .............................13
Internal Food Product Temperatures ...........13
Service
Thermostat Accuracy ......................14
Trouble Shooting .........................14
Trouble Shooting - Error Codes ..............15
500-1D, 2D, 3D
Exterior Service Parts ................. 16-17
Service View - Drawer Assembly ............18
500-1DN, 2DN, 3DN
Exterior Service Parts ................. 19-20
Service View - Drawer Assembly 500-DN .....21
Electronic Service Parts ....................22
Wire Diagrams
Always refer to the wire diagram(s) included with the
unit for most current version.
Warranty
Transportation Damage and Claims ....Back Cover
Limited Warranty ..................Back Cover
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 1
See Transportation Damage and
Claims section located in this manual.
NOTICE:
Additional
manuals are available from the Alto-Shaam
Tech Team Service Department.
®
®
Appliance and accessories may be
heavy. To prevent serious injury,
ALWAYS use a sufficient number
of trained and experienced workers
when moving or leveling appliance
and handling accessories.
°°°
Always include both model and serial numbers in your correspondence
regarding the unit.
Model: _____________________________________
Serial Number: _____________________________________
Purchased From: _____________________________________
Date Installed: ____________ Voltage: _______________
SERIAL NUMBER IS REQUIRED FOR ALL INQUIRIES
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 2
Used to indicate the presence of a hazard that
can or will cause minor personal injury, property
damage, or a potential unsafe practice if the
warning included with this symbol is ignored.
Used to indicate the presence of a
hazard that can or will cause minor or
moderate personal injury or property
damage if the warning included with
this symbol is ignored.
Used to indicate the presence of
a hazard that WILL cause severe
personal injury, death, or substantial
property damage if the warning
included with this symbol is ignored.
Used to indicate the presence of
a hazard that CAN cause personal
injury, possible death, or major
property damage if the warning
included with this symbol is ignored.
•
•
•
•
NOTICE: Used to notify personnel of
installation, operation, or
maintenance information that is
important but not hazard related.
Used to indicate that referral to
operating instructions is a mandatory
action. If not followed the operator
could suffer personal injury.
Used to indicate that referral to
operating instructions is recommended
to understand operation of equipment.
NOTICE: For equipment delivered for use in
any location regulated by the
following directive:
DO NOT dispose of electrical or
electronic equipment with other
municipal waste.
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 3
•
•
•
•
•
•
•
•
•
•
•
•
•
To prevent SERIOUS INJURY,
DEATH, or PROPERTY DAMAGE:
The appliance must be cleaned
thoroughly to avoid deposits of
grease and or food residues inside
the appliance that may catch fi re. If
fat deposits and/or food waste inside
the appliance ignite, shut down the
appliance immediately and keep the
appliance door closed to extinguish
the fi re. If further extinguishing is
required, disconnect the appliance
from the main power and use a fi re
extinguisher (do not use water to
extinguish a grease fi re!). Failure
to clean the appliance properly
invalidates the warranty and relieves
Alto-Shaam of all liability.
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been
given supervision concerning use of
the appliance by person responsible for
their safety.
Children should be supervised to ensure
that they do not play with the appliance.
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 4
1.
2. DO NOT
3.
®
To prevent SEVERE PERSONAL
INJURY or PROPERTY DAMAGE:
ALWAYS use hand protection when
operating this appliance to avoid
burns. Metal parts of this equipment
become extremely hot when in
operation.
Improper installation, alteration,
adjustment, service, cleaning, or
maintenance could result in property
damage, severe injury, or death.
READ and UNDERSTAND the
installation, operating and
maintenance instructions thoroughly
before installing, servicing, or
operating this equipment.
Appliance and accessories may be
heavy. To prevent serious injury,
ALWAYS use a sufficient number
of trained and experienced workers
when moving or leveling appliance
and handling accessories.
FOR YOUR SAFETY
DO NOT store or use gasoline or
other flammable vapors or liquids in
the vicinity of this or any other
appliance.
ba ck
le ft sid e
ri ght sid e
to p
(est.)
500-1D 500-2D 500-3D
net
ship
(est.)
500-1DN 500-2DN 500-3DN
net
ship
MaxiMuM • each dRaweR
MaxiMuM • each dRaweR
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 5
12-5/16"
(312mm)
24-5/8" (624mm)
43-3/8" (1101mm)
24-7/8" (631mm)
26-1/8" (664mm)
25-7/8" (657mm)
11-5/8"
(296mm)
18-15/16" (481mm)
500-1D
500-2D
500-3D
Electrical
Connection
6-3/4" (171mm) FOR
LEG STAND OR 5" (127mm)
CASTER STAND ASSEMBLY
4-7/8" (121mm)
FOR CASTER STAND ASSEMBLY
WITH 3" (76mm) CASTERS
Cord Length:
120V - 5' (1524mm)
208-240V - 8' (2438mm)
230V - 8' (2438mm)
500-1D, 500-2D, 500-3D
500-2d -48, -72 5015151
500-2d -96 5015152
500-3d 5005153
p
(for units with built in trim)
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 6
26-1/8" (664mm)
31-3/16" (792mm)
11-5/8"
(296mm)
18-15/16" (481mm)
500-1D
500-2D
500-3D
6-3/4" (171mm) FOR
LEG STAND OR 5" (127mm)
CASTER STAND ASSEMBLY
4-7/8" (121mm)
FOR CASTER STAND ASSEMBLY
WITH 3" (76mm) CASTERS
8-5/16"
(211mm)
16-11/16"
(423mm)
53-3/4" (1364mm)
24-7/8" (631mm)
Cord Length:
120V - 5' (1524mm)
208-240V - 8' (2438mm)
230V - 8' (2438mm)
Electrical
Connection
500-1DN, 500-2DN, 500-3DN
500-3dN 5015154
55534
5010921
55535
16642
(for units with built in trim)
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 7
1.
2.
3.
This section is provided for the
assistance of qualified and trained
service technicians only and is not
intended for use by untrained or
unauthorized service personnel.
Failure to observe this precaution
may void the warranty.
To prevent Serious injury, death,
or property damage, ALWAYS
disconnect unit from power source
before cleaning or servicing.
To prevent SERIOUS INJURY,
DEATH, or PROPERTY DAMAGE:
All electrical connections must be
made by a qualified and trained
service technician in accordance
with applicable electrical codes.
This appliance MUST be adequately
grounded in accordance with local
electrical codes or, in the absence
of local codes, with the current
edition of the National Electrical
Code ANSI/NFPA No. 70. In Canada,
all electrical connections are to be
made in accordance with CSA C22.1,
Canadian Electrical Code Part 1 or
local codes.
Wire diagrams are located inside the bonnet of the unit.
For CE approved units:
To prevent an electrical
shock hazard between the appliance and other
appliances or metal parts in close vicinity,
an equalization-bonding stud is provided. An
equalization bonding lead must be connected to
this stud and the other appliances/metal parts
to provide sufficient protection against potential
difference. The terminal is marked with
the following symbol.
NOTICE:
voltage phase cycle/hz amps kW
NeMa 5-15p
15a, 125v plug
NeMa 6-15p
15a, 250v plug
plugs Rated 250v
ch2-16p bs 1363 as/Nzs 3112 cee 7/7
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 8
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 9
1.
n
2. UpDown Arrow Keys
Set
Digital DisplayHeat Indicator Light
Temperature Display Key
Actual
To toggle between Set and Actual:
Set
Digital DisplayActual
Temperature Display Key
ACT
Actual
Set
SET
Temperature Display Key
3.
Heat Indicator Light
4. Load the cabinet with hot food only.
5.
UpDown Arrow Keys
THIS WILL NOT NECESSARILY
BE THE FINAL SETTING.
Press the Temperature Display Key at any time to display
the alternate temperature.
1. Temperature Display Key
Down Arrow Key
2.
.
C
3.
Notice: With a power failure, factory test, etc., the control
will retain the ºC or ºF setting selected by the user when
power is restored.
I
o
I
o
I
o
I
o
I
o
I
o
I
o
I
o
On/Off Power
Switch
Digital
Display
Up/Down
Arrow Keys
Heat
Indicator Light
Temperature
Display Key
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 10
BEEF ROAST — Rare 130°F 54°C
BEEF ROAST — Med/Well Done 155°F 68°C
BEEF BRISKET 160°F — 175°F 71°C — 79°C
CORN BEEF 160°F — 175°F 71°C — 79°C
PASTRAMI 160°F — 175°F 71°C — 79°C
PRIME RIB — Rare 130°F 54°C
STEAKS — Broiled/Fried 140°F — 160°F 60°C — 71°C
RIBS — Beef or Pork 160°F 71°C
VEAL 160°F — 175°F 71°C — 79°C
HAM 160°F — 175°F 71°C — 79°C
PORK 160°F — 175°F 71°C — 79°C
LAMB 160°F — 175°F 71°C — 79°C
CHICKEN — Fried/Baked 160°F — 175°F 71°C — 79°C
DUCK 160°F — 175°F 71°C — 79°C
TURKEY 160°F — 175°F 71°C — 79°C
GENERAL 160°F — 175°F 71°C — 79°C
FISH — Baked/Fried 160°F — 175°F 71°C — 79°C
LOBSTER 160°F — 175°F 71°C — 79°C
SHRIMP — Fried 160°F — 175°F 71°C — 79°C
BREADS/ROLLS 120°F — 140°F 49°C — 60°C
CASSEROLES 160°F — 175°F 71°C — 79°C
DOUGH — Proofing 80°F — 100°F 27°C — 38°C
EGGS —Fried 150°F — 160°F 66°C — 71°C
FROZEN ENTREES 160°F — 175°F 71°C — 79°C
HORS D'OEUVRES 160°F — 180°F 71°C — 82°C
PASTA 160°F — 180°F 71°C — 82°C
PIZZA 160°F — 180°F 71°C — 82°C
POTATOES 180°F 82°C
PLATED MEALS 140°F — 165°F 60°C — 74°C
SAUCES 140°F — 200°F 60°C — 93°C
SOUP 140°F — 200°F 60°C — 93°C
VEGETABLES 160°F — 175°F 71°C — 79°C
THE HO LDI NG TEMPERAT URE S LISTED AR E SUGGESTED GU IDELINES ON LY. ALL
FOOD H OLD ING SHOULD BE BASED ON IN TER NAL PROD UCT TEMPERATUR ES.
ALWAYS FO LLO W LOCAL HEA LTH (HYG IEN E) REGULATI ONS FOR ALL IN TER NAL
TEMPERATU RE REQUIREM ENT S.
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 11
To protect stainless steel surfaces,
completely avoid the use of
abrasive cleaning compounds,
chloride based cleaners, or
cleaners containing quaternary
salts. NEVER use hydrochloric acid
(muriatic acid) on stainless steel.
NEVER use wire brushes, metal
scouring pads or scrapers.
N
O
W
I
R
E
B
R
U
S
H
E
S
N
O
S
T
E
E
L
P
A
D
S
N
O
S
C
R
A
P
E
R
S
To prevent SERIOUS INJURY,
DEATH, or PROPERTY DAMAGE:
The appliance must be cleaned
thoroughly to avoid deposits of
grease and or food residues inside
the appliance that may catch fi re. If
fat deposits and/or food waste inside
the appliance ignite, shut down the
appliance immediately and keep the
appliance door closed to extinguish
the fi re. If further extinguishing is
required, disconnect the appliance
from the main power and use a fi re
extinguisher (do not use water to
extinguish a grease fi re!). Failure
to clean the appliance properly
invalidates the warranty and relieves
Alto-Shaam of all liability.
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 12
Notice:
To prevent Serious injury, death,
or property damage, ALWAYS
disconnect unit from power source
before cleaning or servicing.
To prevent serious personal injury,
death, or property damage:
DO NOT steam clean, hose down
or flood the interior or exterior
with water or liquid solution of
any kind. DO NOT use water jet
to clean.
Failure to observe this precaution
will void the warranty.
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 13
Food fl avor and aroma are usually so closely related that
it is diffi cult, if not impossible, to separate them. There
is also an important, inseparable relationship between
cleanliness and food fl avor. Cleanliness, top operating
effi ciency, and appearance of equipment contribute
considerably to savory, appetizing foods.
Most food imparts its own particular aroma and many
foods also absorb existing odors. Unfortunately, during
this absorption there is not a distinction between GOOD
and BAD odors. The majority of objectionable fl avors and
odors troubling food service operations are caused by
bacteria growth. Sourness, rancidity, mustiness, stale or
other OFF fl avors are usually the result of germ activity.
The easiest way to ensure full, natural food fl avor is
through comprehensive cleanliness. This means good
control of both visible soil (dirt) and invisible soil (germs).
A thorough approach to sanitation will provide essential
cleanliness. It will ensure an a ractive appearance of
equipment, along with maximum effi ciency and utility.
More importantly, a good sanitation program provides
one of the key elements in the prevention of food-
borne illnesses.
A comprehensive sanitation program should focus on
the training of staff in basic sanitation procedures. This
includes personal hygiene, proper handling of raw foods,
cooking to a safe internal product temperature, and
the routine monitoring of internal temperatures from
receiving through service.
A controlled holding environment for prepared foods is
just one of the important factors involved in the prevention
of food-borne illnesses. Temperature monitoring and
control during receiving, storage, preparation, and the
service of foods are of equal importance.
The most accurate method of measuring safe temperatures
of both hot and cold foods is by internal product
temperature. A quality thermometer is an eff ective tool for
this purpose, and should be routinely used on all products
that require holding at a specifi c temperature.
Hazard Analysis (at) Critical Control Points (HACCP), is a
quality control program of operating procedures to assure
food integrity, quality, and safety. Taking steps necessary
to augment food safety practices is both cost eff ective
and relatively simple. Additional HACCP information is
available by contacting:
Center for Food Safety and Applied Nutrition
Food and Drug Administration
PHONE: 1-888-SAFEFOOD
www.foodsafety.gov
HOT FOODS
DANGER ZONE 40°F TO 140°F (4°C TO 60°C)
CRITICAL ZONE 70°F TO 120°F (21°C TO 49°C)
SAFE ZONE 140°F TO 165°F (60°C TO 74°C)
COLD FOODS
DANGER ZONE ABOVE 40°F (ABOVE 4°C)
SAFE ZONE 36°F TO 40°F (2°C TO 4°C)
FROZEN FOODS
DANGER ZONE ABOVE 32°F (ABOVE 0°C)
CRITICAL ZONE 0°F TO 32°F (-18°C TO 0°C)
SAFE ZONE 0°F or below (-18°C or below)
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 14
To prevent Serious injury, death,
or property damage, ALWAYS
disconnect unit from power source
before cleaning or servicing.
This section is provided for the
assistance of qualified and trained
service technicians only and is not
intended for use by untrained or
unauthorized service personnel.
Failure to observe this precaution
may void the warranty.
This section is provided for the assistance of qualified technicians only and is not intended for use by untrained
or unauthorized service personnel.
®
☛
Do not attempt to repair or service the unit beyond this point. Contact Alto-Shaam for the nearest authorized
service agent. Repairs made by any other service agents without prior authorization by Alto-Shaam
®
will
void the warranty on the unit.
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 15
Oven will cook in time only
Oven will cook in time only
Notice:
NOTICE:
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 16
6
10
21
9
14
8
33
29
18
30
27
26
25
32
13
24
31
28
23
28
7
16
5
11
17
19
4
12
1
20
2
3
22
15
6
10
21
9
14
8
33
29
18
30
27
26
25
32
13
24
31
28
23
28
7
16
5
11
17
19
4
12
1
20
2
3
22
15
Item PartDescriptionQty
1 1008272 BRACKET, SENSOR MTG. 1
2 1012473 TOP COVER 1
IN-2003 INSULATION, FIBERGLASS, #3 DENS 1/2" 1
4 BK-29606 CONTROL SENSOR BLOCK 1
5 CC-34970 WARMER CONTROL 1
6 GS-23622 GASKET, WITH ADHESIVE 0.125 x 0.375 [lin ft] 1
7 NU-2361 NUT, 6-32 HEX, S/S
8 1012439 INNER BACK PANEL, 500-3D 1
1012673 INNER BACK PANEL, 500-2D 1
1012667 INNER BACK PANEL, 500-1D 1
9 1012445 OUTER CASING, 500-3D 1
1012671 OUTER CASING, 500-2D 1
1012664 OUTER CASING, 500-1D 1
10 1012446 REAR TRIM, 500-3D
1012674 REAR TRIM, 500-2D
1012665 REAR TRIM, 500-1D
11 PE-29685 OVERLAY, 500-D, SIMPLE CONTROL 1
12 PR-34494 PROBE 1
13 SC-22271 SCREW, M4-0.7 x 6mm PHIL
14 BG-24890 BEARING, DRAWER WARMER 6
15 SC-2459 SCREW, 8-32 x 1/4" PHIL SCREW 4
16 WS-23148 WASHER, 6-32, FLAT, NYLON 4
17 SW-34769 SWITCH, ROCKER, 125-277V, 20A1
18 WS-22302 WASHER, SPLIT LOCK 1
19 EL-29738 ELEMENT, HEATER 2
EL-29875 ELEMENT, 320W, FOIL PAD HEATER 1
20 SC-25018 1/4-20 x 1-1/8" FLAT HD 6
21 RI-2100 RIVET, BLIND, #44, STAINLESS 28
22 5013915 DRAWER FRAME ASSB 3
5014559 VENTED DRAWER FRAME ASSB 2
23 5013913 TUBE SPOT ASSB, 500-3D 1
5014254 TUBE SPOT ASSB, 500-2D 1
5014252 TUBE SPOT ASSB, 500-1D 1
24 1003936 HI-LIMIT PROTECTION COVER 1
25 BK-3019 T-BLOCK 1
26 BU-3964 BUSHING, STRAIGHT, STRAIN RELIEF 1
27 CD-3922 CORDSET-16AWG, 3/C, INT’L HARM 1
28 CR-34967 CONNECTOR-2 CONDUCTOR 2
29 WS-22297 WASHER, FLAT 2
30 NU-22770 NUT, THREADED INSERT, M6 1
31 TT-33476 THERMOSTAT, 300°F HI-LIMIT 1
32 SC-2365 SCREW, 6-32 x 1-1/4" ROUND HD 2
33 SC-22924 SCREW, HHCS, M6 x 20, W/NO MARKING 1
3
4
1
1
1
4
500-3D Shown
Part numbers and drawings are subject to change without notice.
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 17
6
10
21
9
14
8
33
29
18
30
27
26
25
32
13
24
31
28
23
28
7
16
5
11
17
19
4
12
1
20
2
3
22
15
6
10
21
9
14
8
33
29
18
30
27
26
25
32
13
24
31
28
23
28
7
16
5
11
17
19
4
12
1
20
2
3
22
15
Item PartDescriptio
nQ
ty
1 1008272 BRACKET, SENSOR MTG. 1
2 1012473 TOP COVER 1
IN-2003 INSULATION, FIBERGLASS, #3 DENS 1/2" 1
4 BK-29606 CONTROL SENSOR BLOCK 1
5 CC-34970 WARMER CONTROL 1
6 GS-23622 GASKET, WITH ADHESIVE 0.125 x 0.375 [lin ft] 1
7 NU-2361 NUT, 6-32 HEX, S/S
8 1012439 INNER BACK PANEL, 500-3D 1
1012673 INNER BACK PANEL, 500-2D 1
1012667 INNER BACK PANEL, 500-1D 1
9 1012445 OUTER CASING, 500-3D 1
1012671 OUTER CASING, 500-2D 1
1012664 OUTER CASING, 500-1D 1
10 1012446 REAR TRIM, 500-3D
1012674 REAR TRIM, 500-2D
1012665 REAR TRIM, 500-1D
11 PE-29685 OVERLAY, 500-D, SIMPLE CONTROL 1
12 PR-34494 PROBE 1
13 SC-22271 SCREW, M4-0.7 x 6mm PHIL
14 BG-24890 BEARING, DRAWER WARMER 6
15 SC-2459 SCREW, 8-32 x 1/4" PHIL SCREW 4
16 WS-23148 WASHER, 6-32, FLAT, NYLON 4
17 SW-34769 SWITCH, ROCKER, 125-277V, 20
A1
18 WS-22302 WASHER, SPLIT LOCK 1
19 EL-29738 ELEMENT, HEATER 2
EL-29875 ELEMENT, 320W, FOIL PAD HEATER 1
20 SC-25018 1/4-20 x 1-1/8" FLAT HD 6
21 RI-2100 RIVET, BLIND, #44, STAINLESS 28
22 5013915 DRAWER FRAME ASSB 3
5014559 VENTED DRAWER FRAME ASSB 2
23 5013913 TUBE SPOT ASSB, 500-3D 1
5014254 TUBE SPOT ASSB, 500-2D 1
5014252 TUBE SPOT ASSB, 500-1D 1
24 1003936 HI-LIMIT PROTECTION COVER 1
25 BK-3019 T-BLOCK 1
26 BU-3964 BUSHING, STRAIGHT, STRAIN RELIEF 1
27 CD-3922 CORDSET-16AWG, 3/C, INT’L HARM 1
28 CR-34967 CONNECTOR-2 CONDUCTOR 2
29 WS-22297 WASHER, FLAT 2
30 NU-22770 NUT, THREADED INSERT, M6 1
31 TT-33476 THERMOSTAT, 300°F HI-LIMIT 1
32 SC-2365 SCREW, 6-32 x 1-1/4" ROUND HD 2
33 SC-22924 SCREW, HHCS, M6 x 20, W/NO MARKING 1
3
4
1
1
1
4
MN-29742 (Rev. 6) 02/16 • Drawer Warmers • 18
12
12
6
4
1
2
8
3
10
4
5
9a
3
1
7a
2
6
10
9
5
11
7
12
12
6
4
1
2
8
3
10
4
5
9a
3
1
7a
2
6
10
9
5
11
7
Item Part Description Qty
1 5017810 DRAWER FRAME SPOT 1
2 5013916 PAN SUPPORT 1
3 BG-24890 BEARING, ROLLER 1
4 SC-25018 SCREW, 1/4-20 x 1-1/8" FLAT HD 2
5 ST-2546 STUD, SHOULDER, SHORT, S/S 4
6 ST-25019 STUD, S/S PIVOT 4
7 5013917 DRAWER INNER W/HANDLE 1
7a 5014558 VENTED DRAWER FRONT SPOT 1
8 1019159 VENT SLIDE 1
9 16467 DRAWER, OUTER 1
9a 1012899 VENTED DRAWER, OUTER 1
10 RI-2100 RIVET, BLIND, #44, S/S 4
11 NU-36239 NUT, INSERT, THREADED, 1/4-20 4
12 NU-2187 NUT, 1/4-20, NC ACORN #18-8, S/S 2
1111
500-D
Part numbers and drawings are subject to change without notice.
Vented Drawer
Non-Vented Drawer
12
12
6
4
1
2
8
3
10
4
5
9a
3
1
7a
2
6
10
9
5
11
7
12
12
6
4
1
2
8
3
10
4
5
9a
3
1
7a
2
6
10
9
5
11
7
Item Part Description Qty
1 5017810 DRAWER FRAME SPOT 1
2 5013916 PAN SUPPORT 1
3 BG-24890 BEARING, ROLLER 1
4 SC-25018 SCREW, 1/4-20 x 1-1/8" FLAT HD 2
5 ST-2546 STUD, SHOULDER, SHORT, S/S 4
6 ST-25019 STUD, S/S PIVOT 4
7 5013917 DRAWER INNER W/HANDLE 1
7a 5014558 VENTED DRAWER FRONT SPOT 1
8 1019159 VENT SLIDE 1
9 16467 DRAWER, OUTER 1
9a 1012899 VENTED DRAWER, OUTER 1
10 RI-2100 RIVET, BLIND, #44, S/S 4
11 NU-36239 NUT, INSERT, THREADED, 1/4-20 4
12 NU-2187 NUT, 1/4-20, NC ACORN #18-8, S/S 2
1111
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
Alto-Shaam 500-1D Owner's manual
- Category
- Food warmers
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Alto-Shaam Drawer Warmers 500-1DN Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
Kramer Electronics PS-1DN Datasheet
-
Alto Shaam 500-2D MARINE Operating instructions
-
Wittco 750-AD-SS Owner's manual
-
Alto Shaam HFM-72 Operating instructions
-
SERV IT 423WDSFS User manual
-
Alto Shaam ED2-96/PL Operating instructions
-
Sage REF 7937-X Operating Instructions Manual
-
Digi-Sense WD-35625-42 Owner's manual
-
Alto Shaam 500-S/HD MARINE Operating instructions
-
Alto Shaam 1000-S/HD Operating instructions
