Members Mark M3207ANG Owner's manual

Members Mark
Brand
Members Mark
Model
M3207ANG
Category
Barbecues & grills
Type
Owner's manual

This manual is also suitable for

Manual # P80109005L - Date:2007/05/08
Natural Gas (NG) Grill
Model M3207ANG
OPERATOR'S MANUAL
Liquid Propane Gas (LPG)
Grill
Model M3207ALP
WARNING
! !
Failure to comply with these instructions could
result in a fire or explosion that could cause
serious bodily injury, death or property
damage.
Before using this grill read all instructions
and perform all gas leak-check procedures even
if the product was pre-assembled by the retailer
or manufacturer.
Use your grill at least 3 feet away from
any wall or surface. Use your grill at least
3 feet away from combustible objects that can
melt or catch fire (such as vinyl or wood siding,
fences and overhangs) or sources of ignition
including pilot lights on water heaters and
live electrical appliances.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
Combustion byproducts produced when using this
product contain chemicals known to the State of
California to cause cancer, birth defects, or other
reproductive harm.
This product contains chemicals known to
the State of California to cause cancer, birth
defects, or other reproductive harm.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
NOTE TO ASSEMBLER / INSTALLER:
Leave this manual with the consumer.
NOTE TO CONSUMER:
Keep this manual for future reference.
RECORD YOUR SERIAL # __________________
(see silver CSA label on main body of grill)
IMPORTANT:
Ÿ
Grill Information Center:
Call us first if you have any problem with
this product. We can help you with ques-
tions about assembly and operation or if
there are damaged or missing parts when
you unpack this unit from the shipping box.
Please call before returning to the store.
1-800-770-9769
8am-4:30pm CST, Monday through Friday
Ÿ
Downloaded from www.Manualslib.com manuals search engine
WARNING
! !
Do not store spare LP cylinder
within 10 feet (3m) of this appliance.
Do not store or use gasoline or
other flammable liquids and
vapors within 25 feet (8m) of this
appliance.
When cooking with oil/grease, do
not allow the oil/grease to get
hotter 350°F (177°C)
Do not leave oil/grease unattended.
3.
1.
2.
4.
WARNING
! !
LPG grill models must be used with Liquid
Propane Gas and the regulator assembly
supplied. Natural Gas models must be used
with Natural Gas only. Any attempt to convert
the grill from one fuel type to another is
extremely hazardous and will void the
warranty.
Never use your gas grill in a garage, porch, shed,
breezeway or any other enclosed area.
Never obstruct the flow of ventilation air around
your gas grill housing.
Never disconnect the gas regulator or any gas
fitting while your grill is lit. A lit grill can ignite
leaking gas and cause a fire or explosion which
could result in property damage, personal injury
or death.
Keep gas regulator hose away from hot grill
surfaces and dripping grease. Avoid unnecessary
twisting of hose. Visually inspect hose prior
to each use for cuts, cracks, excessive wear
or other damage. If the hose appears damaged
do not use the gas grill. Call: 1-800-770-9769
for an authorized replacement hose.
•
•
•
•
•
The Grease Draining Tray must be visually
inspected before each grill use. Remove
any grease and wash Grease Draining
Tray with a mild soap and warm water
solution. Failure to comply with these
instructions could result in a grease
fire or explosion that could cause
serious bodily injury, death or property
damage.
WARNING
! !
2
Leaking gas may cause a fire or
explosion which could result in property
damage, personal injury or death.
DANGER
!
!
1.
2
3.
4.
If you smell gas:
Shut off gas to the appliance.
Extinguish any open flame.
Open lid.
If odor continues, keep away from
the appliance and immediately call
your gas supplier or your fire
department.
Do not store or use gasoline or
other flammable liquids or vapors in
the vicinity of this or any other
appliances.
An LP cylinder not connected for
use shall not be stored in the vicin-
ity of this or any other appliance.
1.
2.
WARNING
! !
Table of Contents
Primary Safety Warnings...........................1-3
Pre-Assembly Instructions..............................3
Part Diagrams and Lists........................4-10
Assembly Instructions.............................11-16
Use & Care Instructions:
• Gas Safety and Leak Tests...........17-20
• Lighting Instructions............................21-22
• Troubleshooting..........................................22
• Rotisserie Instruction...........................23-25
• Cleaning and Maintenance................26-27
• Cooking Guide...................................A1-A3
• Frequently Asked Questions............A4-A5
Warranty Terms...........................Back Cover
Never use charcoal in this gas grill.
Failure to comply with these instructions
could result in a grease fire or explosion
that could cause serious bodily injury, death
or property damage.
WARNING
! !
Downloaded from www.Manualslib.com manuals search engine
Pre-Assembly Instructions For Your Safety
WARNING
! !
For safe operation ensure the Gas Valve Assem-
bly Orifice is inside the Burner Tube before using
your grill. See figure. If the Orifice is not inside
the Burner Tube, lighting the Burner may cause
explosion and/or fire resulting in serious bodily
injury and/or property damage.
Orifice Burner Tube
Gas Valve Assembly
Tools Required for Assembly include:
protective work gloves
protective eyewear
While it is possible for one person to unpack this gas
grill, obtain assistance from another person when
handling the large pieces.
Use the Hardware and Part Diagrams to ensure all
items are included and free of damage.
Do not assemble or operate the grill if it appears
damaged. If there are damaged or missing parts
when you unpack the shipping box or you have
questions during the assembly process, call the:
To expedite the assembly process follow these
general guidelines:
•
•
Grill Information Center 1-800-770-9769
8am-4:30pm CST, Monday through Friday
•
Grill Installation Codes
The installation must conform with local codes or, in the
absence of local codes, with either the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and
Propane Installation Code, CSA B149.1, or Propane
Storage and Handling Code, B149.2.
Spiders and small insects can spin webs and
nest in the grill Burner Tubes during transit and
warehousing which can lead to a gas flow
obstruction resulting in a fire in and around the
Burner Tubes. This type of "FLASHBACK FIRE"
can cause serious grill damage and create an
unsafe operating condition for the user.
To reduce the chance of FLASHBACK
FIRE you must clean the Burner Tubes
as follows before initial use.
Also do this at least once a month in summer
and fall or whenever spiders are active in your
area, and if your grill has not been used for an
extended period of time.
WARNING
! !
Failure to comply with these instructions could
result in a fire or explosion that could cause
serious bodily injury, death or property damage.
METHOD 1: Bend a stiff wire or wire coat
hanger into a small hook as shown and run
the hook through the Burner Tube and inside
the Burner several times to remove debris.
METHOD 2: Use a bottle brush with a flexible
handle and run the brush through the Burner
Tube and inside the Burner several times to
remove any debris.
METHOD 3: Use an air hose to force air
through each Burner Tube. The forced air
should pass debris or obstructions through
the Burner and out the Ports.
TO CLEAN BURNER TUBE, INSERT HOOK
HERE
9
Burner
Foot
Carefully lift each Burner up and away from the
Gas Valve Orifice.
Remove the screw from the rear of each
Burner using a Phillips Head Screwdriver.
Check and clean Burner/Venturi Tubes for insects
and insect nests. A clogged tube can lead to a fire
beneath the grill.
Refer to the figure below and perform one of
these 3 cleaning methods:
1.
2.
3.
4.
Phillips Head Screwdriver
3
Downloaded from www.Manualslib.com manuals search engine
4
Hardware Pack Parts List for Models M3207ALP & M3207ANG
PART # PART DESCRIPTION QTYPURPOSE OF PART
P06002016A Hardware Pack 1 For use in assembly (For LPG model only)
P06002017A Hardware Pack 1 For use in assembly (For NG model only)
S112G03061 Phillips Head Screw 3/16"x3/8" 4 Attaches Cart Rear Panel and Cart Side Panels
P00201001C Door Handle 2 Attaches to Doors
4
Attaches Cart Spice Basket to Cart Bottom Shelf
(For LPG model only)
8
Attaches Cart Spice Baskets to Cart Bottom Shelf
(For NG model only)
S112G03061 Phillips Head Screw 3/16"x3/8" 2
Attaches Upper Door Support Bracket to Left and
Right Cart Side Panel
S112G04191 Phillips Head Screw 1/4"x1-3/16" 4 Attaches Grill Bowl to Cart
S112G04081 Phillips Head Screw 1/4"x1/2" 8 Attaches Side Shelf Brackets to Bowl Panels
S112G04081 Phillips Head Screw 1/4"x1/2" 8
S313G04081 Flange Nut 1/4" 8
S112G03061 Phillips Head Screw 3/16"x3/8" 4
S313G03061 Flange Nut 3/16" 4
P05536001A Hose Holder 2
S112G03061 Phillips Head Screw 3/16"x3/8" 2
S313G03061 Flange Nut 3/16" 2
P05536001A Hose Holder 1
S112G03041 Phillips Head Screw 3/16"x1/4" 2
Attaches NG Regulator Assembly to Right Cart
Panel (For NG model only)
S233G05461 Wing Bolt 5/16"x4-1/2" 1
S303G0504D Special Nut 5/16" 1
S112G03041 Phillips Head Screw 3/16"x1/4" 4 Attaches Door Handles to Doors
Attaches Left Side Shelf and Side Burner Frame to
Bowl Panels
Attaches Regulator Assembly to Cart Rear Panel
(For LPG model only)
S172M04101 Self-Tapping Screw M4x10
Already installed in the Cart Bottom Shelf
Attaches Regulator Assembly to Cart Rear Panel
(For NG model only)
Secures Gas Tank
Preassembled in the Door Handle
Downloaded from www.Manualslib.com manuals search engine
5
Hardware already installed in the Cart Bottom Shelf
Hardware Pack for Models M3207ALP & M3207ANG
Phillips Head Screw
3/16" x 1/4"
Qty. 2 (NG model)
Part# S112G03041
Self-Tapping Screw
M4 x 10
Qty. 4 (LPG model)
Qty. 8 (NG model)
Part# S172M04101
Phillips Head Screw
1/4" x 1/2"
Qty. 16
Part# S112G04081
Flange Nut 3/16"
Qty. 4 (LPG model)
Qty. 2 (NG model)
Part# S313G03061
Phillips Head Screw
3/16" x 3/8"
Qty. 10 (LPG model)
Qty. 8 (NG model)
Part# S112G03061
Phillips Head Screw
1/4" x 1-3/16"
Qty. 4
Part# S112G04191
Flange Nut 1/4"
Qty. 8
Part# S313G04081
Hose Holder
Qty. 2 (LPG model)
Qty. 1 (NG model)
Part# P05536001A
Scale 1:2
Door Handle
Qty. 2
Part# P00201001C
* One Battery/AA included in the Hardware Pack.
Hardware already installed in the Cart Bottom Shelf
Special Nut 5/16”
Qty. 1
Part. # S303G0504D
Scale 1:2
Phillips Head Screw
3/16" x 1/4"
Qty. 4
Part# S112G03041
Wing Bolt 5/16"x4-1/2"
Qty. 1
Part# S233G05461
Scale 1:2
Preassembled in the Door Handle
Downloaded from www.Manualslib.com manuals search engine
Parts Diagram for Models M3207ALP & M3207ANGParts Diagram for Models M3207ALP & M3207ANG
11
13
5
8
3
9
10
12
6
4
1
14
7
2
26
18
47
71
78
81
73
77
72
82
83
88
79
84
80
31
39
19
63
58
61
65
35
36
38
37
40
34
75
73
74
66
86
(LPG Only)
76 74
67
89
55
33
93
57
56
28
30
51
52
32
29
62
92
68(NG Only)
16
60
87
17
59
85
90
91
45
50
46
44
48
49
27
54
43
42
41
53
16
15
17
70
69
23
21
25
24
20
22
64
18
94
68
6
Downloaded from www.Manualslib.com manuals search engine
7
Parts List for Models M3207ALP & M3207ANG
KEY DESCRIPTION PART# QTY
1 Lid Assembly Y0110045 1
2 Temperature Gauge P00601061A 1
3 Lid Handle P00205069B 1
4 Protective Pad P05518002I 4
5 Cooking Rack/Secondary P01516003A 1
6 Cooking Grid P01604014A 2
7 Cooking Grid P01604015A 1
8 Burner/Main P02008024A 3
9 Infrared Burner P02005004A 1
10 Infrared Burner Electrode Assembly Y0320011 1
11 Savor Plates® P01708007B 3
12 Savor Plates® Bracket, Front P03328015A 3
13 Savor Plates® Bracket, Rear P03328017A 3
14 Burner Bracket P0220313HD 1
15 Side Shelf, Left P01106005A 1
16 Side Shelf Bracket, Left Front/Right Rear P01204005B 2
17 Side Shelf Bracket, Right Front/Left Rear P01206005B 2
18 Grill Bowl P0071335SC 1
19 Grease Draining Plate P06902009C 2
20 Back Burner Wind Shield P06905046E 1
21 Back Burner Frame P02011054C 1
22 Back Burner P02007016D 1
23 Back Burner Electrode P02610005B 1
Back Burner Orifice(LPG only) P06527003A 1
Back Burner Orifice(NG only) P06527004A 1
25 Back Burner Extension Tube P03717031B 1
26 Burner Heat Shield P07523003A 1
27 Lid Hinge P05501020A 2
28 Gas Collector Box with Electrode P02609002B 3
29 Electric Wire Set P02615091A 1
30 Electric Wire, 5-contact P02615097A 1
Gas Valve/Manifold Assembly (LPG only) Y0060380 1
Gas Valve/Manifold Assembly (NG only) Y0060381 1
32 Gas Fitting P03906003A 1
33 Control Panel, Upper P02909198S 1
34 Control Panel, Extension P02909401S 1
Control Panel, (LPG only) P02909301A 1
Control Panel, (NG only) P02909311F 1
36 Control Knob Seat P03415014S 5
37 Control Knob Spring P05504021A 5
38 Control Knob for Main Burner P03411403S
3
39 Control Knob for Back/Infrared Burner P03411413S
2
24
31
35
Downloaded from www.Manualslib.com manuals search engine
8
Parts List for Models M3207ALP & M3207ANG
KEY DESCRIPTION PART# QTY
40 Electric Ignitor, 5-port P02502218C
1
41 Side Burner Lid P01127004B
1
42 Side Burner Frame P01104010A
1
43 Side Burner Body P02301015B
1
44 Side Burner Pot Support P00805010A
1
45 Side Burner P02002012A
1
46 Side Burner Electrode P02614007C
1
47 Control Knob for Side Burner P03401043S
1
48 Control Knob Spring P05504021A
1
49 Side Burner Control Knob Seat P03408053S
1
Side Burner Gas Valve (LPG only) Y0060300
1
Side Burner Gas Valve (NG only) Y0060301
1
51 Side Burner Connection Hose, Socket P03705048K
1
52 Side Burner Connection Hose, Plug P03705049H
1
53 Side Burner Extension Hose Bracket P03327028Q
1
54 Side Burner Bracket P03327029S
1
55 Grease Tray P02705205B
1
56 Grease Tray Handle P00213008B
1
57 Grease Tray Heat Shield P06903048B
1
58 Bowl Support Bracket, Left P01301007B
1
59 Bowl Support Bracket, Right P01302007B
1
60 Cart Rear Panel, Upper P06906024C
1
61 Door Hinge Bracket, Left Upper P03302021A
1
62 Door Hinge Bracket, Right Upper P03302022A
1
63 Cart Side Panel, Left P07602017A
1
Cart Side Panel, Right (LPG only) P07603024A
1
Cart Side Panel, Right (NG only) P07603025A
1
65 Door Bracket P01316006B
1
66 Door Magnet P05523004K
4
67 Cart Rear Panel P07701064A
1
Cart Bottom Shelf (LPG only) P01008009C
1
Cart Bottom Shelf (NG only) P01008010C
1
69 Grease Tray Heat Shield, Upper P06903049A
1
70 Grease Tray Heat Shield, Lower P06903050M
1
71 Caster Seat, Left Front/Right Rear P05327035W
2
72 Caster Seat, Right Front/Left Rear P05327036W
2
73 Cart Panel Bracket-A, Left Front/Right Rear P03342001A
2
74 Cart Panel Bracket-A, Right Front/Left Rear P03342002A
2
75 Cart Panel Bracket-B, Left Front P03342003A
1
76 Cart Panel Bracket-B, Left Rear P03342004A
1
77 Cart Panel Bracket-B, Right Front P03342005A
1
50
68
64
Downloaded from www.Manualslib.com manuals search engine
Important: Use only Grand Hall certified replacement parts. The use of any part that is not a factory
authorized part can be dangerous and will also void your product warranty. Keep this Operator's Manual
for convenient referral and for part replacement.
To Order Grand Hall Certified Replacement Parts, Call 1-800-770-9769
To obtain the correct replacement parts for your electric grill, please refer to the part numbers in this parts
list. The following information is required to ensure you receive the correct parts:
1. Model and Serial Number (see UL label on grill)
2. Part Number
3. Part Description
4. Quantity of parts needed
9
Parts List for Models M3207ALP & M3207ANG
KEY DESCRIPTION PART# QTY
78 Cart Panel Bracket-B, Right Rear P03342006A
1
79 Door Hinge Bracket, Left Lower P03302023A
1
80 Door Hinge Bracket, Right Lower P03302024A
1
81 Caster, 2.5 in., with Brake P05110006D
4
82 Door Handle P00201001C
2
83 Door, Left P04302036A
1
84 Door, Right P04303036A
1
85 Regulator with Hose (LPG) P03601004A
1
86 Lighting Stick P05507031E
1
Hose Holder (LPG) P05536001A
2
Hose Holder (NG) P05536001A
1
88 Door Guide Plate P05510019A
1
Cart Spice Basket (LPG only) P05204005B
1
Cart Spice Basket (NG) P05204005B
2
90 Regulator Assembly / NG Y0080007
1
91
Side Burner Extension Hose / NG P03705028F 1
92
Hose, 12ft. / NG P03703001A 1
93 Name Plate
P00414005Q 1
94 Weight
P05344003Q 2
Grill Cover
P07007018A 1
Rotisserie Assembly
Y0250089 1
Hardware Pack (LPG) P06002016A 1
Hardware Pack (NG) P06002017A 1
Operator's Manual
P80109005L 1
89
87
Downloaded from www.Manualslib.com manuals search engine
Y0250089 Rotisserie Assembly Parts Diagram
Grill Information Center: If you have questions about assembly or grill operation, or
if there are damaged or missing parts when you unpack this unit from the shipping box, call us
8:00 am - 4:30 pm CST, Monday through Friday at: 1-800-770-9769
Rot. Screw#10-24x3/4"
UNC
Qty. 2
Part# S112G10124
Rot. Thumbscrew
3/8"x1/2"
Qty. 3
Part# S196G06084
Rot. Washer
Qty. 2
Part#
S411G03084
Rot. Nut#10-24
Qty. 2
Part# S362G10124
Y0250089 Rotisserie Assembly Parts List
KEY
PART#
DESCRIPTION
QTY
Rot. Handle
Rot. Bushing
Rot. Thumbscrew 3/8"x1/2"
Rot. Collar
Rot. Spit
Rot. Holding Fork
Rot. Motor Bracket
Rot. Motor/AC
Rot. Screw #10-24x3/4" UNC
Rot. Washer
Rot. Nut #10-24
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1
1
3
1
1
2
1
1
2
2
2
P05508004E
P05508092F
S196G06084
P05508091F
P05508146F
P05508090F
P03307028A
P07101008B
S112G10124
S411G03084
S362G10124
Hardware for Rotisserie
9
10
11
7
4
8
3
3
6
3
2
1
5
10
Downloaded from www.Manualslib.com manuals search engine
Assembly Instructions
Remove all packed components. Use the parts list to check that all necessary parts have been included.
Assemble the gas grill on a protective work surface to avoid scratching grill surfaces. Inspect your grill for damage
as you proceed. Do not assemble or operate your grill if it appears damaged.
Phillips Head Screw
3/16" x 3/8"
Qty. 4
Part# S112G03061
Secure the Cart Rear Panel between the Cart Side Panels using
2 of 3/16"x3/8" Phillips Head Screws.
Secure the Cart Side Panel, Left/Right using 2 of 3/16"x3/8"
Phillips Head Screws.
2
Install Cart Rear Panel and Cart Side Panels
Unfold the Cart Side Panel, Right, Cart Side Panel, Left and Cart
Rear Panel.
1
Assemble Cart
11
Cart Rear Panel
Downloaded from www.Manualslib.com manuals search engine
Self-Tapping Screw
M4 x 10
Qty. 4 (For LPG only)
Qty. 8 (For NG only)
Part# S172M04101
Phillips Head Screw
3/16" x 1/4"
Qty. 4
Part# S112G03041
Intall the Door Handles to Doors using 4 of 3/16"x1/4" Phillips
Head Screws.
Install the Cart Spice Basket to Cart Bottom Shelf using
4 of M4 x 10 Self-Tapping Screw.
3
Install Door Handles, Cart Spice Basket and Door (two Bas-
kets for NG model)
Phillips Head Screw
1/4" x 1-3/16"
Qty. 4
Part# S112G04191
5
4
Install Door Bracket and Grill Bowl
Phillips Head Screw
3/16" x 3/8"
Qty. 2
Part# S112G03061
Remove cooking components from Grill Head. With an
assistant, lift and position Grill Head on the Cart. Tighten
securely using 4 of 1/4” x 1-3/16” Phillips Head Screws.
Install the Door Bracket between the Left and Right Cart
Side Panel using 2 of 3/16” x 3/8” Phillips Head Screws.
Door Handle
Qty. 2
Part# P00201001C
Insert Bottom Left Door Hinge into Bottom Left Door Hinge
Bracket. Then align Top Door Hinge and insert into the hole
on Top Left Door Hinge Bracket.
Repeat both steps for Right Door.
12
Downloaded from www.Manualslib.com manuals search engine
Attach the Side Shelf Bracket (RR) to the Rear of Right Bowl Panel.
Attach the Side Shelf Bracket (RF) to the Front of Right Bowl Panel.
Tighten securely by using 1/4” x 1/2” Phillips Head Screws.
Repeat for Left Side Shelf Brackets installing.
From the front of the grill, slide the Grease Tray side tabs over the
side rails underneath the Grill Bowl.
5
Install Side Shelf Brackets
Phillips Head Screw
1/4" x 1/2"
Qty. 8
Part# S112G04081
Side Shelf Bracket, (LF)
Side Shelf Bracket, (RR)
Side Shelf Bracket, (RF)
Side Shelf Bracket, (LR)
Grease Tray
Flange Nut 1/4"
Qty. 8
Part# S313G04081
Place the Side Shelf over the Left Side Shelf Brackets and
Side Burner Frame over the Right Side Shelf Brackets.
Tighten securely by using Screws and Nuts provided.
6
Install Left Side Shelf and Right Side Burner Frame
Phillips Head Screw
1/4" x 1/2"
Qty. 8
Part# S112G04081
13
Downloaded from www.Manualslib.com manuals search engine
Push back Sleeve of the Socket. See Figure A.
Insert Plug then release Sleeve. See Figure B.
Push Plug until sleeve snaps forward locking the
Plug into the Socket. See Figure C.
Push the Side Burner Hose into hose holder.
7
Install Side Burner Connection Hose
S
o
c
k
e
t
P
l
u
g
Figure A
Figure B
Figure C
SLEEVE
SLEEVE
SOCKET
Hose Holder
Sleeve
PLUG
Place the LPG Regulator inside the cart through the
opening above Cart Rear Panel. Fix the hose of LPG
Regulator by Hose Holder onto Cart Rear Panel.
Tighten securely by using Screws and Nuts provided.
8-1
Install Regulator Assembly (For LPG model only)
Hose Holder
Qty. 2
Part# P05536001A
Scale 1:2
Flange Nut 3/16"
Qty. 4
Part# S313G03061
Phillips Head Screw
3/16" x 3/8"
Qty. 4
Part# S112G03061
14
LPG Regulator
Cart Rear Panel
Hose
Hose
Holder
Downloaded from www.Manualslib.com manuals search engine
Hose Holder
Qty. 1
Part# P05536001A
Scale 1:2
Flange Nut 3/16"
Qty. 2
Part# S313G03061
Phillips Head Screw
3/16" x 3/8"
Qty. 2
Part# S112G03061
Figure 2
Natural Gas Regulator
Connection Hose
Cart Side Panel, Right
Brass Nut
Figure 1
Install NG Regulator Assembly to Right Cart Side Panel
using 2 of 3/16” x 1/4” Phillips Head Screws.
Place the NG regulator into the hole on Right Cart Side
Panel. Tighten securely using Brass Nut found in the NG
Regulator. See Fig. 1.
Fix the hose of NG Regulator onto Cart Rear Panel. Tighten
securely by using Screws and Nuts provided. See Fig. 2.
Install Regulator Assembly (For NG model only)
8-2
Phillips Head Screw
3/16" x 1/4"
Qty. 2
Part# S112G03041
15
NG Regulator
Hose
Holder
Hose
Cart Rear Panel
Downloaded from www.Manualslib.com manuals search engine
Failure to read and follow the Use and Care
Instructions could result in a fire or explosion
that could cause serious bodily injury, death or
property damage.
WARNING
!!
Final Grill Assembly Step
When you have finished assembling your
grill be sure that all screws are tightened
for safe operation of your grill.
Be sure all Control Knobs are set to
"OFF" and open the Grill Lid.
Have your assistant stand behind to the
right of the grill and look toward the front
of the grill bowl. Never put your face
inside the Grill Head.
Turn the Control Knob of Main Burners
to IGN and push in and have assistant
watch for a blue spark within each Gas
Collector Box. If a spark is present the
Electrode Tips are properly positioned.
If no spark is seen, the Spark Gap
needs to be adjusted as follows:
•
•
•
Using an adjustable wrench, loosen the
Inside Nut until the Gas Collector Box can
be turned upward.
If the gap between the Spark Elec-
trode Tip and Receiver is more than
3/16" use long nose pliers to gently
squeeze the Gas Collector Box to
narrow gap.
Return the Gas Collector Box to its
original position, secure the Inside Nut
and try the Electrode Check again. If no
"clicking" sound is heard:
AA Battery may be installed back-
wards.
Electric wires may be loose. Remove
the AA Battery and inspect the Ignitor
Junction Box found behind the Control
Panel and reconnect any loose wires.
Side Burner Electrode Check
11
Open side burner lid. Remove plastic
shipping band from burner and pot
support.
Push and turn side burner Control Knob
to HIGH. Look for spark between tip of
electrode and burner.
If you don't see a spark from side burner elec-
trode, adjust gap between electrode and
burner surface to 3/16 in.
Spark Electrode Tip
Spark Receiver
Inside Nut
12
Place the Savor Plates
®
above the
Burners.
Place the Cooking Grids on the ledge
above the Savor Plates
®
.
Place the Secondary Cooking Rack on
the slots on either side of the Grill
Bowl.
Savor Plates
Cooking Grids
Secondary Cooking Rack
®
-
-
Install Ignitor Battery
9
Unscrew Ignitor Cap from Control Panel.
Place supplied AA battery into the Ignitor
Slot with positive pole facing you.
Position the Cap and Spring over the AA
battery and tighten onto Control Panel.
With the assistance of another person,
perform this Electrode Check before
proceeding.
10
This test will ensure that the Spark Electrode Tips
are properly positioned so your grill lights easily
and properly.
Ignitor Slot
AA Battery
Ignitor Cap
+
_
Spring
Spark Gap
Gas Collector Box
Install Cooking Components
16
Downloaded from www.Manualslib.com manuals search engine
USE AND CARE INSTRUCTIONS
CORRECT LP GAS TANK USE
LP Gas grill models are designed for use with a
standard 20 lb. Liquid Propane Gas (LP Gas) tank,
not included with grill. Never connect your gas grill to
an LP Gas tank that exceeds this capacity. A tank of
approximately 12 inches in diameter by 18-1/2 inches
high is the maximum size LP Gas tank to use. You
must use an "OPD" gas tank which offers a listed
Overfill Prevention Device. This safety feature
prevents tank from being overfilled which can cause
malfunction of LP Gas tank, regulator and/or grill.
Never connect an unregulated LP gas tank to your
gas grill. The gas regulator assembly supplied with
your gas grill is adjusted to have an outlet pressure
of 11" water column (W.C.) for connection to an LP
gas tank. Only use the regulator and hose assembly
supplied with your gas grill. Replacement regulators
and hose assemblies must be those specified by
the Manufacturer.
Have your LP Gas dealer check the release valve
after every filling to ensure it remains free of defects.
Always keep LP Gas tank in upright position.
Do not subject the LP Gas tank to excessive heat.
Never store an LP Gas tank indoors. If you store
your gas grill in the garage always disconnect the
LP Gas tank first and store it safely outside.
LP Gas tanks must be stored outdoors in a well-
ventilated area and out of the reach of children.
Disconnected LP Gas tanks must not be stored in a
building, garage or any other enclosed area.
The regulator and hose assembly can be seen after
opening the doors (if applicable) and must be
inspected before each use of the grill. If there is
excessive abrasion or wear or if the hose is cut, it
must be replaced prior to using the grill again.
Never light your gas grill with the lid closed or
before checking to ensure the burner tubes are fully
seated over the gas valve orifices.
Never allow children to operate your grill. Do not
allow children or pets to play near your grill.
Use of alcohol or drugs may impair the ability to
assemble and operate the appliance.
Keep fire extinguisher readily accessible. In the
event of a oil/grease fire, do not attempt to
extinguish with water. Use type B extinguisher
or smother with dirt, sand or baking soda.
In the event of rain, cover the grill and turn off
the burner and gas supply.
Use your grill on a level, stable surface in an
area clear of combustible materials.
Do not leave grill unattended when in use.
Do not move the appliance when in use.
Allow the grill to cool before moving or storing.
Do not use your grill as a heater.
This grill is not intended to be installed in
or on recreational vehicles and/or boats.
Never use charcoal in this gas grill.
17
The LP Gas tank must be constructed and marked
in accordance with the Specifications for LP-Gas
Cylinders of the U.S. Department of Transportation
(D.O.T.) or the National Standard of Canada, CAN/
CSA-B339, Cylinders, Spheres and Tubes for Trans-
portation of Dangerous Goods; and Commission,
as applicable.
The LP Gas tank must have a shutoff valve,
terminating in an LP Gas supply tank valve outlet,
that is compatible with a Type 1 tank connection
device. The LP Gas tank must also have a safety
relief device that has a direct connection with the
vapor space of the tank.
The tank supply system must be arranged for
vapor withdrawal.
The LP Gas tank used must have a collar
to protect the tank valve.
•
•
•
WARNING
!
!
Use your grill at least 3 feet away from any
Use your grill at least 3 feet
away from combustible objects that can melt
or catch fire (such as vinyl or wood siding,
fences and overhangs) or sources of ignition
including pilot lights on water heaters and live
electrical appliances.
Never use your gas grill in a garage, porch, shed,
breezeway or any other enclosed area.
Never obstruct the flow of ventilation air around
your gas grill housing.
wall or surface.
WARNING
!!
Do not store a spare LP-Gas tank under or near
this appliance.
Never fill the tank beyond 80 percent full; and
If the information in "(a)" and "(b)" is not followed
exactly, a fire causing death or serious injury may
occur.
A.
B.
C.
Downloaded from www.Manualslib.com manuals search engine
18
USE AND CARE INSTRUCTIONS
NOTE about LP Gas Tank Exchange Programs
Many retailers that sell grills offer you the option of
replacing your empty LP Gas tank through an ex-
change service. Use only those reputable exchange
companies that inspect, precision fill, test and certify
their tanks. Exchange your tank only for an OPD safety
feature-equipped tank as described in the LP Gas tank
section of this manual.
Ÿ
How to Leak Test your LP Gas Tank
LP Gas Model only:
Secure a 20lb LP Gas Tank to Gas Grill
If growing bubbles appear do not use or move
the LP Gas tank. Contact an LP Gas Supplier
or your fire department!
WARNING
!
!
Use a clean paintbrush and a 50/50 mild soap and
water solution.
Brush soapy solution onto LP Gas tank in the
areas indicated by the arrows. See diagram.
If growing bubbles appear do not use or move the
LP Gas tank. Call an LP Gas Supplier or your Fire
Department.
All leak tests must be repeated each time your LP
Gas tank is exchanged or refilled.
When checking for gas leaks do not smoke.
Do not use an open flame to check for gas leaks.
Your grill must be leak tested outdoors in a well-
ventilated area, away from ignition sources such as
gas fired or electrical appliances. During the leak test,
keep your grill away from open flames or sparks.
Do not use household cleaning agents. Damage to
gas assembly components can result.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
For your safety:
Leak test new and exchanged LP Gas tanks BEFORE
connecting one to your grill.
Always keep new and exchanged LP Gas tanks in an
upright position during use, transit or storage.
Turn your LP Gas Tank Valve clockwise to the
closed or OFF positon.
Place LP Gas tank into tank hole on bottom shelf
Install the tank so the Tank Valve faces the rear
right corner of cabinet.
Screw the Wing Bolt in to secure the gas tank.
Special Nut 5/16”
Qty. 1
Part. # S303G0504D
Scale 1:2
Wing Bolt 5/16”x4-1/2”
Qty. 1
Part. # S233G05461
Scale 1:2
Downloaded from www.Manualslib.com manuals search engine
USE AND CARE INSTRUCTIONS
Check all connections for LP Gas Leaks
Never test for leaks with a flame. Prior to first use,
at the beginning of each season, or every time
your LP Gas tank is changed, you must check for
gas leaks. Follow these three steps:
Make a soap solution by mixing one part liquid
detergent and one part water.
Turn the grill Control Knobs to the full OFF
position, then turn the gas ON at source.
Apply the soap solution to all gas connections
indicated by the arrows. See diagram. If
bubbles appear in the soap solution the
connections are not properly sealed. Check
each fitting and tighten or repair as necessary.
Gas Valve / Manifold Assembly
Regulator with Hose (LPG)
LP Gas Tank
If you have a gas leak that cannot be repaired by
tightening, turn off the gas at the source, disconnect
fuel line from your grill and call 1-800-770-9769
or your gas supplier for repair assistance.
Never disconnect the gas regulator or any gas
fitting while your grill is lit. A lit grill can ignite
leaking gas and cause a fire or explosion which
could result in property damage, personal injury
or death.
WARNING
! !
LP Gas Model only:
Connect Regulator with Hose to your LPG Tank
Turn all Burner Valves to the OFF position.
Inspect the valve connection port and regulator
assembly for damage or debris. Remove any
debris. Never use damaged or plugged
equipment.
Connect the regulator assembly to the tank valve
and HAND TIGHTEN nut clockwise to a full stop.
DO NOT use a wrench to tighten because it could
damage the Quick Coupling Nut and result in a
hazardous condition.
Open the tank valve 1/4 to 1/2 (counterclockwise)
and use a soapy water solution to check all
connections for leaks before attempting to light
your grill. See "Checking for LP Gas Leaks". If
a leak is found, turn the tank valve off and do not
use your grill until the leak is repaired.
Type 1 connection per
ANSI Z21.58a - 2006
Quick
Coupling Nut
CAUTION: When the appliance is not in use the gas
must be turned off at the tank.
Before using this gas appliance read all
instructions and perform all gas leak-check
procedures even if the product was
pre-assembled by the retailer or manufacturer.
WARNING
! !
Disconnecting A Liquid Propane Gas (LPG)
Tank From Your Grill
Make sure the Burner Valves and LP Gas tank valve
are off. (Turn clockwise to close.)
Detach the hose and regulator assembly from the
LP Gas tank valve by turning the Quick Coupling
Nut counterclockwise.
19
Downloaded from www.Manualslib.com manuals search engine
20
USE AND CARE INSTRUCTIONS
Natural Gas Model only:
Connecting Natural Gas To Your Grill
WARNING
!!
Figure 1
Figure 2
Gas Supply
Inside Wall
Outside Wall
Male Fitting
To Grill
Locking
Shut Off
Shut Off
Quick
Disconnect
Your natural gas grill is designed to operate on
natural gas only, at a pressure of 4" water column
(W.C.) with natural gas regulator. The gas pressure
Regulator supplied with this appliance must be
used. This Regulator is set for an outlet pressure
of 4" W.C.
Install a Shutoff Valve at the gas supply source
outdoors at a point after the gas pipe exits the
outside wall and before the quick-disconnect hose.
Or install it at the point before the gas line piping
Pipe sealing compound or pipe thread tape
resistant to the action of natural gas must be used
on all male pipe thread connections.
Disconnect your gas grill from fuel source when the
gas supply is being tested at high pressures. This
gas grill and its individual shutoff valve must be
disconnected from the gas supply pipe system
during any pressure testing of that system at
pressure in excess of 1/2 psi (3.5kpa).
Turn off your gas grill when the gas supply is being
tested at low pressures. The grill must be isolated
from the gas supply pipe system by closing its
individual manual shutoff valve during any pressure
testing of the gas supply pipe system at pressures
equal to or less than 1/2 psi (3.5kpa).
Natural Gas Safety Instructions
Connect the Swivel nut of the 12' Natural Gas
Hose to the horizontal fitting of NG Regulator
as shown in Fig. 1. Connect the other hose
end (male plug) to the gas supply line from
house. Also, read and follow all natural gas
safety instructions below.
enters the ground. See Fig. 2.
If you have a gas leak that cannot be repaired
by tightening, turn off the gas at the source,
disconnect fuel line from your grill and call
1-800-770-9769
or your gas supplier for repair
assistance.
Check all connections for NG Leaks
Never test for leaks with a flame. Prior to first use,
at the beginning of each season, you must check
for gas leaks. Follow these three steps:
Make a soap solution by mixing one part liquid
detergent and one part water.
Turn the grill Control Knobs to the full OFF
position, then turn the gas ON at source.
Apply the soap solution to all gas connections
indicated by the arrows. See Fig. 3. If bubbles
appear in the soap solution the connections
are not properly sealed. Check each fitting and
tighten or repair as necessary.
Figure 3
Horizontal fitting
Hose, 12 ft./ NGSwivel nut
NG Regulator
Hose, 12 ft./ NG
Gas Valve / Manifold Assembly
Downloaded from www.Manualslib.com manuals search engine
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33

Members Mark M3207ANG Owner's manual

Members Mark
Brand
Members Mark
Model
M3207ANG
Category
Barbecues & grills
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents