Optoma 4K500 User manual

4K500
Optoma
Brand
Optoma
Model
4K500
Category
Data projectors
Type
User manual

Optoma 4K500: Experience cinematic 4K UHD resolution with HDR10 compatibility for lifelike visuals. Game with ultra-low latency of 4.2ms in Enhanced Gaming Mode. Immerse yourself in powerful audio via built-in speakers or connect external devices through multiple ports, including HDMI 2.0, DisplayPort 1.2a, and HDBaseT. Customize your viewing experience with 1.6x optical zoom, vertical lens shift, and 4-corner correction.

Optoma 4K500: Experience cinematic 4K UHD resolution with HDR10 compatibility for lifelike visuals. Game with ultra-low latency of 4.2ms in Enhanced Gaming Mode. Immerse yourself in powerful audio via built-in speakers or connect external devices through multiple ports, including HDMI 2.0, DisplayPort 1.2a, and HDBaseT. Customize your viewing experience with 1.6x optical zoom, vertical lens shift, and 4-corner correction.

Note: For an optimum image performance “Focus compensation calibration”
must be completed after the installation of your projector.
1. Press and hold the power button “ ”on the keypad of the unit, and
then plug in the power cord.
2. Press the down arrow “
” on the keypad of the unit. (The projector’s
fans will be triggered at full capacity)
3. Wait 15 minutes and then unplug the power cord.
4. Plug in the power cord and turn on the projector by pressing the power
button “
” on the projector keypad.
5. Turn On “Compensate focus” following these steps: Press “Menu”
button on the remote control > go to Setup page > Lens function >
Compensate focus > Calibration > press “ENTER”key.
6. After selecting “Yes”, the power “
” will turn purple. If the power “
” LED is not purple, you must wait until the LED turn purple.
7. Display a grid test pattern by following these steps: Press the “Menu”
button on the remote control > go to Setup page > Select Test Pattern.
Focus compensation
Calibration Procedure
8. Once test pattern is up on your screen, adjust
the focus to optimize the image (Press “F2” on
the remote control to call Focus menu, and then
adjust focus by pressing the right and left keys
keys).
9. Press the “Info” key on the remote control. The
power “
” LED on the projector will be ashing
purple for approximately 2.5 minutes.
When the power “
” LED on the projector
turns solid purple, this indicates the projector
has nished saving the rst Focus compensation
calibration settings.
10. Lens thermal aberration could take around 20
minutes until reaching a stable state, during
this time focus can be adjusted by following the
process mentioned on step number 8.
11.
When focus is stable (after min 20 ), press “Re-Sync” key on the remote
control.
The Power
“ “ LED will ash purple approximately 4 seconds.
When the power LED “ “ turns solid purple, this indicates the projector
has nished saving the second Focus compensation calibration settings.
12. Turn o the projector by pressing the power o button “
” on the
remote control. The “Compensate Focus” setting will be set to “On”.
Note:
- This calibration process is only required during the rst time of
installation or change to dierent projection size.
- During the calibration process period, it can’t input any signals.
On
Geometric
Mode
Correction PIP/PBP
Off
F1 F2
AV Mute
ENTER
Source
Volume D Zoom
Info.
F3
Format Freeze Remote
Re-Sync
Menu
1 2
USB Power
Out(5V-1.5A)
Service
RS-232
12V Out
A
12V Out
B
HDMI 1 HDMI 2
(HDCP2.2)
HDMI 3 HDMI Out
DisplayPort
VGA/YPbPr
RJ-45
Wired Remote
a
b*
3 4
On
Geometric
Correction PIP/PBP
or
5 6
USB Power
Out(5V-1.5A)
Service
RS-232
12V Out
A
12V Out
B
HDMI 1 HDMI 2
(HDCP2.2)
HDMI 3 HDMI Out
DisplayPort
VGA/YPbPr
RJ-45
Wired Remote
MOLEX
MOLEX
On
Geometric
Mode
Correction PIP/PBP
Off
F1 F2
AV Mute
ENTER
Source
Volume D Zoom
Info.
F3
VGA
1
S-Video
2
HDMI1
3
HDMI2
HDMI3
Format Freeze Remote
ID All
HDBaseT
4
Video
5
DVI
6
BNC
7
YPbPr
8
DisplayPort
9
3D
0
Re-Sync
Menu
Basic user manual
Focus
Zoom
Note:
• Some keys may have no function for
models that do not support these features.
• The default values of the function keys are:
- F1: Zoom
- F2: Focus
- F3: IRIS
  • Page 1 1
  • Page 2 2
  • Page 3 3

Optoma 4K500 User manual

4K500
Optoma
Brand
Optoma
Model
4K500
Category
Data projectors
Type
User manual

Optoma 4K500: Experience cinematic 4K UHD resolution with HDR10 compatibility for lifelike visuals. Game with ultra-low latency of 4.2ms in Enhanced Gaming Mode. Immerse yourself in powerful audio via built-in speakers or connect external devices through multiple ports, including HDMI 2.0, DisplayPort 1.2a, and HDBaseT. Customize your viewing experience with 1.6x optical zoom, vertical lens shift, and 4-corner correction.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents