Rex-Electrolux CASSETTO User manual

Piedistallo con cassetto per lavatrice

Washing machine stand with drawer

Piédestal avec tiroir pour machine à laver le linge

Waschmaschinenuntersatz mit Schublade

Pedestal con cajón para lavadora

Pedestal para máquina de lavar roupa com gaveta

Sokkel met lade voor wasmachine

Vaskemaskinesokkel med skuffe

Vetolaatikollinen pesukoneen jalusta

Vaskemaskinsokkel med skuff

Tvättmaskinsställning med låda

Pračka s podstavcem se zásuvkou

Cokół pod pralkę z szufladą

Подиум стиральной машины с ящиком

Podstavec na práčku so zásuvkou

Çekmeceli çamaþýr makinesi standý

Istruzioni di montaggio

Assembly instructions

Montageanleitung

Instructions de montage

Instrucciones de montaje

Instruções de montagem

Montageaanwijzingen

Monteringsanvisninger

Asennusohjeet

Monteringsanvisninger

Monteringsanvisningar

Pokyny k montáži

Instrukcje montażu

Инструкция по сборке

Montážne pokyny

Montaj talimatlarý

132 972 471

132972471 I-UK.qxd 07/05/2007 17:33 Pagina 1

Page is loading ...

8

Warning:

Do not install the stand on a washing machine/tumble dryer

column. This stand with drawer is suitable only for front loading

washing machine of the Electrolux Group.

Please check its compatibility consulting your machine instruction

booklet or call your nearest local Service Centre. The pedestal

must be used only for washing machine having spin speed higher

than 600 rpm.

Important:

1. If the washing machine is already connected to the domestic

hydraulic and electric system, proceed as follows:

●

pull out the plug from the mains,

●

stop water supply by closing the tap,

●

disconnect the inlet pipe and the drain pipe and get ready to

collect any water left in the machine with a shallow basin.

2. With a brand new washing machine, do as follows:

●

install the stand before connecting the machine to water and

electricity mains,

●

follow the instructions to remove any transport safety

equipment.

Before you start installing the stand on your washing machine

make sure you have plenty of room. Avoid working in restricted

spaces as the installation and subsequent adjustment operations

may turn out quite awkward and difficult to carry out.

Take the stand out of its package and use the cardboard to rest

washing machine and stand on, so you won’t scratch the

equipment varnish and the floor.

In the stand’s drawer you’ll find an envelope with all the necessary

material for a correct assembly.

Have ready a Phillips screwdriver to fit rear brackets to the stand

and to washing machine cabinet.

The pack includes:

2 rear metal brackets;

6 self-tapping screws (4.2 x 13 mm);

1 key to adjust stand and washing machine’s feet.

132972471 I-UK.qxd 07/05/2007 17:33 Pagina 8

Before starting the installation, adjust the stand's feet in order to

achieve a perfectly stable horizontal position.

Proceed as follows (fig. 1):

●

loosen the nuts using the supplied key

●

adjust the feet to allow for an uneven floor

●

tighten up all check nuts.

Note:

Never place cardboard, wood or similar materials under the

stand’s feet to compensate for any unevenness in the floor.

Fit one of the rear brackets to the left side of the stand’s back using

the screws provided (fig.2 and 3).

PDST02C

PDST25C

PDST15C

9

fig.1

fig.2 fig.3

132972471 I-UK.qxd 07/05/2007 17:33 Pagina 9

Lay gently the washing machine on the detergent compartment

side (fig.4).

Loosen the washing machine’s adjusting feet using the provided

key, then undo 5 complete turns (fig.5 and 6).

Note:

If the feet are already partly undone, you must first screw them on

again and then undo 5 complete turns.

Slide the stand under the washing machine so that its front

adjusting feet match the stand’s front brackets (fig.7) and the rear

bracket is positioned against the machine’s back (fig.8).

PDST08CD

PDST07C

PDST26C

cinque

giri

PDST05C

PDST03CD

10

fig.5

fig.7 fig.8

fig.6

5 complete

turns

fig.4

132972471 I-UK.qxd 07/05/2007 17:33 Pagina 10

Screw the rear bracket onto the machine’s back using one of the

the remaining screws (fig.9).

Return machine and stand to a vertical position, and screw the

other bracket onto the stand and the machine’s back using the

remaining screws (fig.10 and 11).

The stand is now installed; check whether your washing machine’s

back feet rest on it (fig.12). Otherwise undo them using the key

provided with the stand (fig.13).

PDST13CD

Piedistallo

Lavatrice

PDST12C

PDST29C

PDST10CD

PDST28C

11

fig.10 fig.11

fig.12 fig.13

Washing Machine

Stand

fig.9

132972471 I-UK.qxd 07/05/2007 17:34 Pagina 11

The stand’s drawer, with a capacity of up to 35 kg, contains two

dividers; they may be taken out if you wish (fig.14); the drawer was

designed with a special compartment inside where you can find a

supplied folding plastic box quite useful to store your washing

laundry (fig.15).

The drawer slides on two metal runners and can easily be pulled

out to the full. Should you wish to remove the drawer, you must pull

it out completely (fig.16) and act on the two black plastic levers

halfway through the metal runners.

Pull the right lever up and the left lever down: the drawer will be

uncoupled from the runners and easily removed (fig.17).

Warning:

Do not place any solvent or flammable substance into the drawer,

as the fumes could be a possible cause of fire.

PDST19C

PDST18C

PDST17C

PDST16C

12

fig.16 fig.17

fig.14 fig.15

132972471 I-UK.qxd 07/05/2007 17:34 Pagina 12

Page is loading ...

Rex-Electrolux CASSETTO User manual

This manual is also suitable for

Rex-Electrolux CASSETTO User manual

in other languages

Other documents