Wells Manufacturing M4200-3SV User manual

Wells Manufacturing
Brand
Wells Manufacturing
Model
M4200-3SV
Type
User manual

This manual is also suitable for

WELLS BLOOMFIELD, LLC
2 ERIK CIRCLE, P. O. Box 280 Verdi, NV 89439
telephone: 775-689-5707
fax: 775-689-5976
www.wellsbloomfield.com
p/n 305607 Rev. B ECN-13360 I 270 071023 cps
INSTALLATION INSTRUCTIONS
KIT# 22914
RETROFIT OVEN DOOR
A. REMOVE OLD DOOR AND STRIKE ASSEMBLIES
1. Remove oven top panel and lower front panel as required to
access door pivots. Retain all panels and screws for later
reinstallation.
2. Remove door. On left side of new door, retract hinge pins:
a. Remove and save two inner screws
b. Loosen two outer screws
c. Slide hinge pins into door
Remove and save hinge pins, brackets and screws.
3. Remove and save two screws holding strike assembly.
Discard strike assembly.
4. Remove and discard oven door gaskets.
5. Remove two screws holding upper pivot. Discard upper pivot.
270
Page 1 of 3
CAUTION:
SHOCK HAZARD
Disconnect appliance from electric
power before opening any access
panel.
CAUTION:
BURN HAZARD
Allow appliance to cool completely
before servicing.
NOTE: DO NOT remove or discard
lower pivot.
TOP
REMOVE AND DISCARD
UPPER PIVOT ASSEMBLY
REMOVE AND SAVE
UPPER AND LOWER HINGE PIN,
BRACKETS AND SCREWS
REMOVE AND DISCARD
SAVE SCREWS
STRIKE ASSEMBLY
REMOVE AND DISCARD
DOOR ASSEMBLY
DO NOT REMOVE
LOWER HINGE PIVOT ASSEMBLY
Page 2 of 3
B. PREPARE OVEN CAVITY
1. Examine oven door gaskets.
2. Install new set of oven door gaskets if old gaskets are worn,
warped, cracked or burnt.
C. INSTALL NEW DOOR ASSEMBLY
1. Clean as necessary all hinge pins, brackets and screws
saved from Step A.
2. Remove all packing materials and protective plastic from new
door assembly.
3. On left side of new door, loosely install hinge pins:
a. Slide hinge pins into door.
b. Install brackets and outer screws.
Do not tighten screws at this time.
4. Insert upper pivot bushing into hole in frame. Insert from the
bottom.
5. Set new door in place. Slide hinge pins out until they are fully
engaged in upper and lower pivots. Install inner screws, then
tighten.
6. Install strike. Flat side of strike mounts away from the oven
cavity.
CAUTION:
SHOCK HAZARD
Disconnect appliance from electric
power before opening any access
panel.
CAUTION:
BURN HAZARD
Allow appliance to cool completely
before servicing.
HINGE PIN
OUTER
HINGE
SCREWS
INNER
HINGE
SCREWS
BRACKET
UPPER PIVOT
BUSHING
LOWER
PIVOT
ASSEMBLY
STRIKE
Page 3 of 3
D. ADJUST DOOR
1. Carefully close door:
a. Door should clear frame top and bottom
b. Strike should securely hold door closed
2. Examine door for alignment:
a. Gap between top of door and frame, and between bottom
of door and frame must be approximately equal. Adjust
height of door by loosening jamb nut, then turning pivot on
its screw mounting. Clockwise lowers the door height.
Re-tighten jamb nut .
b. Gap between left side of door and frame must be the
same from top to bottom. Adjust door for plumb by
loosening holding screws. Turn adjusting bolt to increase
or decrease gap at bottom. Clockwise increases gap.
Re-tighten holding screws.
c. Gap between top of door and frame must be the same
from side to side. Adjust door for level by loosening
holding screws, then raising or lowering latch-end of door
until it is level. Re-tighten holding screws.
E. FINISHING UP
Reinstall top and bottom panels.
Procedure is complete
CAUTION:
SHOCK HAZARD
Disconnect appliance from
electric power before opening any
access panel.
CAUTION:
BURN HAZARD
Allow appliance to cool
completely before servicing.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Wells Manufacturing M4200-3SV User manual

Wells Manufacturing
Brand
Wells Manufacturing
Model
M4200-3SV
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents