2. Ultra Start
  3. 7

Ultra Start 7, 007 User manual

  • Hello! I am an AI chatbot trained to assist you with the Ultra Start 7 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
007 Remote Wrist Watch
Advanced Digital Wrist Watch with Alarm and Remote Starter
Control Capabilities.
The system must be placed into Service Mode before any service work is started on the
vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The
manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)
- The Hood Pin Safety Switch Must Always be Installed!
Warning!!
CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH!
It is the sole responsibility of the user to place the system in Service Mode
when parking a vehicle equipped with a remote starterin an enclosed
area ex: garage, partially enclosed area ex: carport, or when the vehicle is being serviced.
ULTRA
1. Change from Mode to Mode Page 2
00
00
38
88
00
0:00
0:00
12:38
18:88
6:00
00
SU 5-16
SU 5-16
AL
CHR
P
P
TMR
ALM
A
MODE
MODE
MODE
MODE
MODE
Program Start Mode
Real Time Mode
Timer Mode
Alarm Mode
Chronograph Mode
Press and release the MODE button to switch from Mode to Mode.
MODE SELECT
Real Time Mode
Alarm Mode
Chronograph Mode
Timer Mode
Program Start Mode
Returns to Real Time Mode
MODE BUTTON
Default Screen
Mode Button Once
Mode Button Twice
Mode Button Three times
Mode Button Four times
Mode Button Five times
3. Dual Time Mode
2. Real Time Mode- How to Set Time and Date Page 3
38
38
38
12:38
12:38
18:38
RESET
MODE
2 seconds
ST.STP
ST.STP
TMR
TMR
SU 12-16
SU 12-16
SU 12-16
P
P
P
1. Press and hold the MODE button to enter the Real Time Setting Mode.
2. Press the ST.STP button to select 12 or 24 hour format.
3. Press the RESET button to go to the next field, hour digits will begin to flash.
4. While the hour digits are flashing, press the ST.STP button to increase the
number. Hold the ST.STP button to change the number at a greater speed.
5. Aftter you set the 12/ 24 hour format, hour, minute, second, year, month and
date, press the MODE button to exit.
38
38
12:38
3:38
ST.STP
12 1-38
SU 12-16
A
P
P
1. In real time mode, press the ST.STP button to switch between the Real Time
Mode and Digital Time Mode.
2.Set the Dual Time in the same manner as the Real Time.
4. Alarm Mode Page 4
How to Set Alarm Time
00
00
6:00
6:00
ST.STP
ST.STP
AL
AL
A
A
ALM
ALM
00
00
00
6:00
6:00 8:00
RESET
MODE
2 seconds
ST.STP
ST.STP
ST.STP
AL
ALM
ALM
ALM
A
A
1. In real time mode, press the MODE button to enter the Alarm Mode.
2. Press the ST.STP button to set the alarm ON/OFF.
When the Bell Icon is displayed, the alarm will sound at the preset time every
day for 30 seconds.
-To stop the alarm, press any button.
If the alarm is ON, the Bell Icon will be turned ON in all other modes.
1. In real time mode, press the MODE button to enter Alarm Mode.
2. Hold the MODE button for 2 seconds, the hour digits will begin to flash.
3. While the hour digits are flashing, press the ST.STP button to increase the
number. Hold the ST.STP button to increase the digits at a greater speed.
4. Press RESET to enter the next field, minute digits will begin to flash.
5. To set the minute press the ST.STP button.
6. After you have set the minute, press the MODE button to exit and save.
5. Chronograph Mode Page 5
00
01
08
0:00
0:01
0:08
ST.STP
ST.STP
00
53
53
CHR
CHR
CHR
A
RESET
TMR
1. In real time mode, press the MODE button to enter the Chronograph Mode.
2. Press the ST.STP button to start chrono. To stop the chrono, press the
ST.STP button.
When the chrono is stopped press the RESET button so reset the time to zero
When the chrono time is running, the “CHR” icon will begin to flash in all other
modes with the exception of Setting Modes.
6. Timer Mode Page 6
How to Set the Timer
00
00
00
00:00
00:00 6:00
RESET
MODE
2 seconds
ST.STP
ST.STP
TMR
TMR
TMR
00
58
00
00:20
00:18
0:00
RESET
ST.STP
TMR
TMR
TMR
1. In real time mode, press the MODE button 3 times to enter Timer Mode.
2. Press the ST.STP button to start the timer. To stop, press the ST.STP again.
If the timer is stopped, press RESET to reset the time to the present value.
When the timer is running, the TMR Icon flashes in all other modes with the
exception of setting modes.
3. Press the MODE button to exit.
1. In real time mode, press the MODE button to enter the Timer Mode.
2. Hold the MODE button for 2 seconds, the hour digits will begin flashing.
3. While the hour digits are flashing press the ST.STP button to increase the
number. Hold the ST.STP button to increase the number at a greater speed.
4. Press RESET to go to the next field, minute and seconds will begin flashing.
5. After you have set the minute and seconds , press the MODE button to save
and exit
7. Program Start Mode Page 7
How to Set the Engine Start
38
38
38
12:38
12:38
12:38
PS 8-20
PS 6-20
PS 6-20
P
P
P
TMR
TMR
TMR
PRO
PRO
RESET
ST.STP
ST.STP
MODE
2 seconds
A
A
A
38
38
38
12:38
12:38
12:38
SU 5-16
PS 6-20
PS 6-20
A
P
P
PRO
PRO
MODE
ST.STP
A
A
1. In real time mode, press the MODE button 4 times to enter the Program Start
mode.
2. Press the ST.STP button to change the ON/OFF function of the Program Start.
When the “PRO” icon is ON, the engine will start and run at the preset time. The
remote will beep three times to confirm starting of the engine. The remote start
will only activate when the system is armed and within RF operating range.
3. Press the MODE button to exit.
1. Press the MODE button to enter the Program Start Mode.
2. Hold the MODE button for 2 seconds, the hour digits will start flashing.
3. While the digits are flashing, press the ST.STP button to increase the number.
Hold down the ST.STP button to change the number at a greater speed.
4. To set the minute, press the RESET button.
5. After you set the hours and minutes, press the MODE button to exit and save.
Remote Control Mode For Vehicles Page 8
Battery Replacement
Change the battery when the Low battery icon is displayed on the LCD screen.
Replace with Lithium CR2032 Battery.
*To avoid possible water damage, have the battery changed professionally.
Caution
DO NOT DISASSEMBLE THIS WATCH FOR ANY OTHER REASON THEN TO
REPLACE THE BATTERY. REMOVING ANY OTHER COMPONENT(S) WILL
VOID THE WARRANTY.
Arm/ Lock- Press and release.
Panic Mode- Press and hold for
2 seconds.
Disarm/ Unlock- Press and release
Trunk Release- Press and hold for
2 seconds.
Button 1
Light Button
Button 2
Remote Start- Press and release
Remote Stop- Press and hold for
2 seconds.
Program Start On
MODE Button
Light Button
Button 1
Low Battery
ST.STP Button
Alarm On
Reset Button
Button 2
This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance voids the
users authority to operate this device.
FCC Notice
/