Soleus Air 000/12 - BTU Multi-Room Heat/Cool Room Air Conditioner User manual

10,000 / 12,000 BTU Portable Air Conditioner

LX-100/LX-100BL/LX-120/LX-120BL

Operating Instructions

Model No. LX-100/120

Thank you for choosing a Soleus Air Portable Air Conditioner. This owner’s manual will provide you

with valuable information necessary for the proper care and maintenance of your new product. Please

take a few moments to thoroughly read the instructions and familiarize yourself with all the opera-

tional aspects of your new Soleus Air Portable Air Conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT INSTRUCTIONS

Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference.

1) Always place the unit on a level surface.

2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this

manual.

3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or

outlet grilles.

4) The unit must be connected to a correctly grounded power supply.

5) Do not start or stop the unit by inserting or pulling out the power plug.

6) Do not use an adapter plug or extension cord.

7) Do not use the unit in the immediate surroundings of a bath, a shower or a swimming pool.

8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this

manual.

9) Do not let children play near this unit.

10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced

by the manufacturer or a qualified service technician.

11) When cleaning the unit, always turn the unit off and unplug the power cord.

SPECIFICATIONS

• The cooling capacity is measured at an ambient temperature of DB 86 °F, WB 78 °F.

• Noise level is measured at a distance of 3.28 ft away from the front of the unit, when the unit is in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

• If the environment temperature is higher than the max operating temperature or lower than the minimum operating

temperature, the air conditioner may not work properly.

PACKAGE CONTENTS

Portable Air Conditioner

Exhaust Hoses (2)

Hose Adapters (2)

Window Kit Adapter (2)

Remote Control

AAA Batteries (2)

Window Kit - 3 Sliding Panels (1 dual hose panel, 2 extension panels)

Air Intake and Outlet Covers (2)

Owner’s Manual

MODEL LX-100 & LX-100BL / LX-120 & LX-120BL

COOLING CAPACITY 10,000 BTU/H / 12,000 BTU/H

HEATING CAPACITY 1350 Watts / 1350 watts

DEHUMIDIFYING CAPACITY 50 pts/Day / 60 pts/Day

POWER

COOLING 1020 W / 1350 W

HEATING 1350W / 1350W

AIR FLOW VOLUME 225 CFM

POWER SOURCE

115 V~ 60 HZ

9/12 AMP / 12/12 AMP

COOLING/HEATING

SOUND PRESSURE LEVEL 46 dB(A)

NET WEIGHT 76 Lbs / 82 Lbs

OPERATING

TEMPERATURE

COOLING

60.8℉-107.6℉

HEATING

23℉-89.6℉

DIMENSIONS

ASSEMBLED

17.5” W ×32.75” H ×19” D

PACKAGE

22.4” W ×34.44” H ×19.88” D

REFRIGERANT R22

PRODUCT DIAGRAM

Casters

Louvers

Signal Receptor

Control Panel

Filter Compartment

Air Intake Cover/Filter

PARTS & ASSEMBLY

PARTS

EXHAUST HOSES

WINDOW KIT

ASSEMBLY & INSTALLATION

INSTALLATION

When the unit is operating as an air conditioner or dehumidifier, the unit draws in fresh outdoor air and exhausts hot air

out of the room to complete the air exchange. When the unit is operating in fan or heater modes, no outdoor air exchange

takes place. The window kit and exhaust hose do not need to be installed when the unit is used as a fan or heater.

NOTE: The supplied window kit can be installed in sliding windows and sliding glass doors up to 8 ft. long

(approximate length).

MOUNTING THE EXHAUST HOSES

• Choose a suitable location, near a grounded electrical outlet and suitable window or door. Remove

packaging and locate components.

• Extend both ends of the exhaust hoses approximately 6 inches.

• Screw the window kit adapter onto one end of the exhaust hose clockwise. Screw the hose adapter onto

the other end of the exhaust hose clockwise. Repeat on the other exhaust hose.

• Remove outlet covers from the back of the unit by screwing them counter-clockwise, then lifting up.

• Mount the exhaust hoses onto the back of the unit by locking the hose adapters into place.

DUAL HOSE WINDOW KIT INSTALLATION

CONTROL PANEL, DISPLAY, & OPERATING INSTRUCTIONS

CONTROL PANEL & MULTI-COLOR DISPLAY

CONTROL PANEL

MULTI-COLOR DISPLAY

POWER BUTTON

MODE BUTTON

TIMER BUTTONS

TEMP & TIMER SELECTION

FAN SPEED BUTTON

AUTO A/C DEHUM. FAN HEAT

FAN SPEED

TIMER ON

TIMER OFF

TEMPERATURE

AND TIMER

INDICATOR

OSCILLATION ON/OFF SLEEP MODE ON/OFF EMERGENCY

CONDENSATE-

BUCKET FULL

SWING (LOUVER

OSCILLATION)

COMPRESSOR ON/OFF

OPERATING INSTRUCTIONS

CONTROL PANEL BUTTONS (Refer to the images on page 7)

1) Power On and Off - Press the POWER button once to manually turn the unit on. Press the POWER

button once more to turn the unit off.

2) Mode Selection - Press the MODE Button repeatedly to cycle between the different modes: Auto mode,

Air Conditioner, Dehumidifier, Fan only, and Heater.

3) Fan Speed Control - Press the FAN SPEED Button to cycle through the different fan speeds: High,

Medium, and low. The fan speed can be visually distinguished by the speed of the digital air segments

progressing out from the windmill fan image on the Multi-color display. There is an additional auto speed

setting that is enabled in only heating and cooling modes. This speed is next setting after low when press-

ing the speed control button. The speeds will cycle through in this order: Low, Medium, High, Auto. Each

change in speed will be associated with a “beep” sound from the unit.

4) Temperature - Select the desired temperature by pressing either ▼ or ▲ key when using the unit in

cooling or heating mode. The temperature indicator flashes to display the desired temperature setting. After

the temperature is set, the unit will display this temperature setting until it is changed by the user. The

Multi-color display shows temperature in Celsius or Fahrenheit. Press the ▼ or ▲ simultaneously to

change from C° to F°.

5) SWING - To turn on the exclusive WAVEFLO® oscillation, press the SWING button on the control

panel. Once you press SWING, the louvers on the unit will oscillate up and down and back and forth.

6) Timer - To program the timer, press the TIMER ON button until the display shows a flashing “ ”.

Press the ▲ or ▼ buttons to change the clock to the desired time for the unit to automatically turn on.

Press the TIMER OFF button and the display on the unit will flash “ ”. Press the ▲ or ▼

buttons to change the clock to the desired time for the unit to automatically turn off. The TIMER OFF

indicator will flash for 3 seconds to activate the times you programmed.

NOTE: The timer will also remember your settings when it is set. If you set the timer while in Air Condition-

ing mode, the timer will automatically turn the unit on and off in air conditioning mode according to the de-

sired programmed times. The timer will also remember the temperature settings, fan speed, and oscillation set-

ting. The timer works when the unit is in Air Conditioner mode, Heating mode, Dehumidifier mode, Fan

mode, and Auto mode

OPERATING THE UNIT USING THE CONTROL PANEL

Air Conditioner Mode

1) Install the exhaust hoses and window kit properly (see pages 6).

2) Plug the Power Cord into an electrical outlet.

3) Turn on the unit by pressing the POWER button on the control panel.

4) Press the Mode button until the “ ” icon appears on the Multi-color display

5) Press the ▲ or ▼ buttons until the desired room temperature appears on the control panel

display. The temperature ranges from 61

F - 88

F (16

C - 31

C).

6) Select the desired fan speed by pressing the FAN button.

NOTE: During hot days, the unit will cool the room most efficiently by setting the temperature at the lowest

setting and the fan speed on high. Reducing the length of the exhaust duct, insulating the exhaust hose and

window kit, and keeping direct sunlight to a minimum will also improve the cooling efficiency.

Dehumidifier Mode

1) Install the exhaust hoses and window kit properly (see pages 6).

2) Plug the Power Cord into an electrical outlet.

3) Turn on the unit by pressing the POWER Button on the control panel.

4) Press the MODE button until the “ ” appears on the control panel display.

NOTE: The unit operates at low fan speed during dehumidifier mode. The unit cools room slightly during

the dehumidification. Keep the windows and doors closed to aid the effectiveness of the unit in removing the

moisture from the room.

NOTE: The unit will not perform in dehumidifier mode when the room temperature is lower than 61

F .

Fan Mode

1) Plug the Power Cord into an electrical outlet.

2) Turn on the unit by pressing the POWER button on the control panel.

3) Press the MODE button until the “ ” icon appears on the control panel display.

4) Select the fan speed by pressing the FAN button.

5) To circulate more air, press the SWING button on the remote control. The louvers will oscillate in our

exclusive WAVEFLO® pattern; back and forth and up and down, spreading more air throughout the

room.

NOTE: It is not necessary for the exhaust hoses and window kit to be installed to operate the unit in fan mode.

Heating Mode

1) Plug the Power Cord into an electrical outlet.

2) Turn on the unit by pressing the POWER button on the control panel.

3) Press the MODE button until the “ “ icon appears on the control panel display.

4) Press the ▼or ▲ buttons until the desired room temperature appears on the control panel display. The

temperature ranges from 61

F - 88

F (16

C - 31

C).

5) Select the fan speed by pressing the FAN button. It is recommended to set the fan speed to low.

NOTE: It is not necessary for the exhaust hoses and window kit to be installed to operate the unit in heating

mode.

Auto Mode

1) Install the exhaust hoses and window kit properly (see pages 6).

2) Plug the Power Cord into an electrical outlet.

3) Turn on the unit by pressing the POWER button on the control panel.

4) Press the MODE button until the “ ” icon appears on the control panel display. Select the fan speed

by pressing the FAN button.

NOTE: During AUTO mode, the unit operates in Heating mode when the room temperature is below 68

Dehumidifier mode when the room temperature is between 68

F to 80

F. And Air Conditioner mode when

the room temperature is above 80

Sleep Mode (This mode can only be selected when using the Remote control )

1) To set Sleep mode, make sure the unit is in Air Conditioner mode.

2) Press the SLEEP Button on the remote control. The “ ” icon appears on the control panel display.

3) When in SLEEP mode, the fan will run on low to keep fan noise at a minimum.

4) When in Air Conditioner mode, the temperature setting will gradually increase to 2

F above the original set

temperature for 6 hours. After 6 hours the temperature setting will return to the set temperature.

5) When in Heating mode, the temperature setting will gradually decrease to 2

F below the original set tem-

perature for 6 hours. After 6 hours, the temperature setting will return to the set temperature.

6) When in Dehumidifier mode, the temperature will not change when Sleep mode is selected.

Compressor Indicator

The “ ” icon will light up on the control panel display when the compressor turns on. The “ ” icon will

turn off when the compressor shuts off.

Emergency Condensate Holding Tank

When the room temperature is low and the indoor humidity is high, the air conditioner may not be able to

evaporate some of the moisture fast enough. When this happens, the water will accumulate in an emergency

condensate tank inside the unit. Once the emergency condensate tank is full, the unit will automatically shut

off and the “ ” will appear on the control panel display. To empty the condensate tank, pull the drain plug

at the bottom back of the unit. You will need a small pan, approximately 1” high to catch the water coming out

of the condensate tank. Once the condensate tank is drained, the unit will begin working within a few minutes.

The emergency condensate tank is approximately 1.5 Liters of water. Another option is to purchase a small

hose from a hardware store that can fit around the 5/8” drain plug on the back of the unit and drain the unit into

a gravity drain or larger pan for continuous drainage. It is not advised to use continuous drainage when the

room temperature is higher than 90

F .

REMOTE CONTROL

TIMER ON

TIMER OFF

LCD DISPLAY

POWER BUTTON

MINUTE SELECTER

SLEEP BUTTON

HOUR SELECTER

TEMP SETTING

MODE BUTTON

FAN SPEED

SWING (LOUVER

OSCILLATION)

OPERATING THE UNIT USING THE REMOTE CONTROL

REMOTE CONTROL OPERATING INSTRUCTIONS

1) Power On and Off - Press the POWER (I/O) button once to manually turn the unit on. Press the Power

button once more to turn the unit off. When you press the POWER button the upper right square on the

remote control LCD Display will light up. When in Air Conditioner, Heating, and Auto mode, the selected

temperature will appear on the remote control display. When the unit is in Fan mode and Dehumidifier

mode you will see the “- -” icon instead of the set temperature. This shows that temperature selection is not

available when the unit is in Fan or Dehumidifier mode.

2) Mode Selection - Press the MODE Button repeatedly to cycle between the different modes: Auto, Air

Conditioner, Dehumidifier, Fan only, and Heater mode. The upper left square on the Remote control dis-

play will light up showing which mode is selected. In Air Conditioner mode the display will show

“COOLING”, in Heating mode the display will show “HEAT”, in Dehumidifier mode the display will

show “DRY”, in Fan mode the display will show “FAN”, and in Auto mode the display will show

“AUTO”.

3) Fan Speed - Press the FAN speed button to cycle through low, medium, and high fan speeds. The dis-

play on the remote control will show LOW, MED, & HIGH under the “SPEED” label on the remote con-

trol LCD display. There is an additional auto speed setting that is enabled in only heating and cooling

modes. This speed is next setting after low when pressing the FAN speed button on the remote control.

The speeds will cycle through in this order: High, Medium, Low, Auto. Each change in speed will be as-

sociated with a “beep” sound from the unit. The remote control will not display “AUTO” under the speed

label. Once Auto fan speed is selected the unit will beep and there will not be a fan speed displayed on the

remote control.

4) Temperature Setting - When the unit is in Air Conditioner or Heating mode you can select your desired

temperature. Press the ▲ or ▼ to select your desired temperature setting. The temperature on the LCD dis-

play on the remote control will increase or decrease accordingly. Pressing the ▼and ▲ buttons simultane-

ously will change the temperature select between °F and °C.

5) SWING - To turn on the exclusive WAVEFLO® oscillation, press the SWING button on the remote

control. Once you press SWING, the louvers on the unit will oscillate up and down and back and forth.

The bottom left square of the remote control display will show the “ “ icon when WAVEFLO®

oscillation (SWING) is selected.

6) TIMER - To program the timer, first press the T-ON button. Once T-ON is pressed the auto-on timer will

blink in the bottom right rectangle of the remote control display. Press the MIN and HOUR buttons to

change the clock to the desired time for the unit to automatically turn on. The minutes will increase by 10

with each press of the MIN button and the hours will increase by 1 with each press of the HOUR button.

Press the T-OFF button and the remote control display will flash the desired auto-off timer. Press the MIN

and HOUR buttons to change the clock to the desired time for the unit to automatically turn off. The timer

is set when the auto-off time stops flashing and the words “ON” and “OFF” are displayed next to the time.

7) CLOCK - To set the clock on the remote control, hold down either the MIN or HOUR button until the

displayed time flashes on the remote control display. Change the minutes by pressing the MIN button and

change the hours by pressing the HOUR button.

MAINTENANCE

Note: Make sure power is off and the power cord is not plugged into an electrical outlet prior to

performing any maintenance on the unit.

Clean or replace filter - If the air filter is blocked with a dust, the airflow volume may reduce. It is

recommended to clean the filter once every two weeks or as needed.

1) Remove the filter from the filter compartment on the back of the unit.

2) Wash the air filter by immersing it gently into warm water with a neutral detergent. Rinse the filter

and dry it thoroughly out of sunlight.

3) Slide the filter back into the filter compartment after it is thoroughly dried.

4) If the filter is torn or unusable, order a new filter by calling the customer service number on the

warranty page of this manual.

Clean the unit Housing

1) Keep the unit from being exposed directly to the sun to prevent color fading.

2) Clean the surface with a damp cloth and dry it with a soft towel.

Storing the Unit for an Extended Period of Time or Transporting the unit

1) Empty any excess water by unplugging the water drainage stop in the back of the unit (located at

the bottom).

2) Unplug the unit.

3) The unit should be stored in a cool dry place.

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE

PRESENTATION OF THE MANUFACTURER. SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT

TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN.

WARRANTY

One Year Limited Warranty

Soleus International Inc. warrants the accompanying Soleus Air Portable Air Conditioner to be free of defects in mate-

rial and workmanship for the applications specified in its operation instruction for a period of ONE (1) year from the

date of original retail purchase in the United States.

If the unit exhibits a defect in normal use, Soleus International Inc. will, at its option, either repair or replace it, free of

charge within a reasonable time after the unit is returned during the warranty period.

As a condition to any warranty service obligation, the consumer must present this Warranty Certificate along with a

copy of the original purchase invoice.

THIS WARRANTY DOES NOT COVER:

• Damage, accidental or otherwise, to the unit while in the possession of a consumer not caused by a defect in

material or workmanship.

• Damage caused by consumer misuse, tampering, or failure to follow the care and special handling provisions

in the instructions.

• Damage to the finish of the case, or other appearance parts caused by wear.

• Damage caused by repairs or alterations of the unit by anyone other than those authorized by Soleus Interna-

tional Inc.

• Freight and Insurance cost for the warranty service.

ALL WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANT ABILITY ARE LIMITED TO

ONE-YEAR DURATION OF THIS EXPRESS LIMITED WARRANTY. SOLEUS INTERNATIONAL INC.

DISCLAIMS ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES AND IN NO EVENT

SHALL SOLEUS INTERNATIONAL INC’S LIABILITY EXCEED THE RETAIL VALUE OF THE UNIT FOR

BREACH OF ANY WRITTEN OR IMPLIED WARRANTY WITH RESPECT TO THIS UNIT.

This warranty covers only new products purchased from our authorized dealers or retailers. It does not cover used, sal-

vaged, or refurbished products.

As some states do not allow the limitation or exclusion of incidental or consequential damages, or do not allow

limitation on implied warranties, the above limitations and exclusions may not apply to you. This warranty gives you

specific legal rights, and you may also have other rights that vary from state to state.

For Technical Support & Warranty Service

Please Call (888) 876-5387

Or Write To:

Soleus International Inc.

9451 Telstar Ave.

El Monte, CA 91731 USA

Soleus Air 000/12 - BTU Multi-Room Heat/Cool Room Air Conditioner User manual

Related papers

Other documents