Qtx 154.097UK User manual

Brand: Qtx

Model: 154.097UK

Category: Stroboscopes & disco lights

Type: User manual

This manual is also suitable for

DM-X6

Qtx 154.097UK is a compact and versatile DMX controller designed for controlling DMX PAR fixtures with 3, 4, 5, or 6-color (RGB+W+A+V) mixing. With its intuitive layout and various control options, it allows for easy and precise lighting control in various applications.

DM-X6

Mini DMX PAR Controller

Item ref: 154.097UK

User Manual

154.097UK User Manual

Introduction

Thank you for choosing the DM-X6 mini DMX PAR controller as part of your lighting control system.

This unit is designed to control DMX PAR fixtures with 3, 4, 5 or 6-colour (RGB+W+A+V) mixing.

Please read these instructions to gain the best results from this item and avoid damage through misuse.

Unpacking

Your DM-X6 should reach you in good condition and should be supplied with an appropriate mains adaptor.

If there are any signs of damage or items missing from the packaging, contact your dealer immediately.

Warning

To prevent risk of fire or electric shock, do not expose any components to rain or moisture.

Avoid any impact or extreme pressure to the housing or control surface.

No user serviceable parts inside - do not open the case. Refer all servicing to qualified service personnel.

Placement

The DM-X6 may be free standing on a stable surface or wall mounted by either hanging on screws with the

rear punch-holes or flush-mounting with the 4 front mounting holes.

Safety

 Check for correct mains voltage before connecting the D.C. adaptor

 Ensure DMX leads are good condition with no short connections or damaged plugs

Cleaning

 Use a soft dry or slightly damp cloth to clean the casing. Do not use strong solvents

 Periodically clear any debris from fader slots with a soft brush

Panel Layouts

1. RGBWAV/D channel faders

2. DMX Group buttons

3. Channel Mode button & indicators

4. Run Mode Select (Auto or Sound)

5. Blackout

6. Strobe

7. RGBW Colour Mix

8. Amber/Violet Mix

9. MAC Auto Programs

10. Speed control

11. Strobe Speed/Sound Sensitivity control

12. DMX out XLR

13. D.C. input jack

14. Power switch

154.097UK User Manual

Setting up

Connect all PAR lights to be controlled in a chain from DMX outputs to DMX using a good quality DMX leads

(XLRF-XLRM) and connect the DMX OUT connector (12) on the DM-X4 to the DMX input of the first PAR

light in the chain. Various DMX PAR lights may have different channel allocations and the DM-X4 can be set

to one of 6 modes to control these. The chart below shows the 6 modes with channel fader allocations.

Mode

For cans with DMX allocation

RGBD

Red

Green

Blue

Master

RGB cans + CH4 Master Dim

RGBWD

Red

Green

Blue

White

Master

RGBW cans + CH5 Master Dim

RGBWAD

Red

Green

Blue

White

Amber

Master

RGBWA cans + CH6 Master Dim

RGBWAV

Red

Green

Blue

Master

Amber

Violet

RGBWAV cans

DRGBWAV

Green

Blue

White

Amber

Violet

Red+M

RGBWAV cans CH1 UV/Master Dim

RGBWAVD

Red

Green

Blue

White

Amber

RGBWAV cans with Master on CH7

Note: RGBWAVD mode transmits 100% on CH7 to hold master dimming open.

Select the correct mode to match the type of PAR cans to be controlled. The above table gives examples of

fader 1-6 allocations and it important to try each mode to see which delivers the correct behaviour from the

lights that the DM-X6 is controlling. Remember that there may be a choice of DMX modes on each type of

PAR can and it is best to set all cans to a similar DMX mode. Selecting a mode that does not match the DMX

allocation of the fixture(s) may give unexpected and confusing results or may not work at all.

In addition, the DM-X6 can control 4 groups of lighting fixtures separately via the four Group buttons (2).

Each group of PAR lights should be set with the relevant start address as shown below.

Group

DMX start address

Pressing the “1-10” Group button, engages Group 1

Pressing the “11-20” Group button, engages Group 2

Pressing the “21-30” Group button, engages Group 3

Pressing the “31-40” Group button, engages Group 4

Multiple groups can be selected together to control simultaneously

Groups that are selected are indicated by a blue flashing LED and any controls from the DM-X6 will affect

the group(s) selected. When a particular group is switched out, any further fader movements will not affect

that group. This feature makes a multi-zone light show possible with selected groups operating from auto

programs or sound-activated (see below) and others with manual control or static colour.

Operation

Connect the supplied mains adaptor to the DC input of the DM-X6 (13) and switch the power on (14)

For the selected group(s), moving the channel faders controls the amount of red, green, blue, white, amber

and ultra-violet light output of DMX PAR fixtures.

In addition to the 4 channel faders, the DM-X6 has a MIX fader (7) which allows fast access to RGBW colour

mixes in a single movement. For warm colours and UV content, an additional AV MIX slider (8) controls the

amount of amber and violet components in the output.

For strobe effects, pressing the Strobe button (6) will perform a white flashing sequence with a rate of

between 1Hz and 20Hz governed by the Strobe Speed/Sound Sensitivity slider (11). Moving the slider to

zero produces no strobe output. Releasing the Strobe button will return lights back to the previous state.

154.097UK User Manual

Colour changing sequences are available by selecting “AUTO” on the Run Mode button (4) and moving the

MAC slider (9) to one of the 8 internal programs (MAC1 – MAC8 shown below). The speed of the selected

program is governed by the Speed Control slider (10) with step intervals from 0.1sec to 30sec.

MAC 1

Red / Green / Blue scroll

MAC 2

Red / Green / Blue sequence

MAC 3

RGBW scroll

MAC 4

RGBW sequence

MAC 5

Red / Green sequence

MAC 6

Red / Blue sequence

MAC 7

Blue / Green sequence

MAC 8

RGBWAV sequence

Alternatively, selecting “SOUND” on the Run Mode button will engage sound-activated mode, which makes

colour jumps to a music beat detected by the internal microphone. The sensitivity of the internal

microphone is controlled via the Strobe Speed/Sound Sensitivity slider (11).

To switch off all lights, a latching Blackout button (5) sets all DMX channels to zero value, indicated by a

flashing LED. Pressing this button

When not in use for long periods, switch off power and disconnect the adaptor from the mains.

Specifications

Power supply

9-12Vdc, 800mA adaptor (supplied)

Controls

R, G, B, W, A, V/D, RGBW mix, AV mix, MAC, speed, strobe/sensitivity

Mode(s)

RGBD, RGBWD, RGBWAD, RGBWAV, DRGBAV, RGBWAVD

Output

DMX (XLRF)

Dimensions

248 x 110 x 58mm

Weight

1.31kg

Troubleshooting

No power

Check mains voltage is correct and outlet is switched on

Check mains adaptor is OK and connected properly

No DMX control

Check DMX leads are OK and connected correctly

Check correct group button is selected (flashing LED)

Check that light fixture is set to the correct DMX start address

DMX control not

working as expected

Check that the correct mode is selected for the type of fixture

Check that light fixture is set to the correct DMX mode

Check that light fixture is set to the correct DMX start address

Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or

Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.

The goods must be disposed of according to your local council guidelines.

Errors and omissions excepted.

Qtx 154.097UK User manual

Brand: Qtx

Model: 154.097UK

Category: Stroboscopes & disco lights

Type: User manual

This manual is also suitable for

DM-X6

Download PDF

report

Qtx 154.097UK User manual

This manual is also suitable for

Qtx 154.097UK User manual

Related papers

Other documents