2
ShowerSpa Assembly
1. Shower Arm: Align two mounts with pre-drilled holes in ShowerSpa.
To align top mount loosen allen set screw (#19) inside mount and
adjustaccordinglytottophole.Insertthreadedmountthroughholesin
ShowerSpa and secure with soft washer (#10) and nut (#11) supplied.
Tightenset screw (#19) inside mount. CAUTION: Do NOT over tighten
setscrew.Attachshowerheadsupplylinetothelowershowerarmmount.
Makesurerubberwasherisinsertedinsidetting.Installshowerheadonto
showerarm.
2. Glass Shelf: Position glass shelf into slotted mounts. Secure allen
set screws (#18) on the under side of mounts. Do NOT over-tighten
screws.
3. Hand Held Hose and Wand: Attachhexagonnutendofhose(#9)to
handheldhoseoutlet(#20).NOTE:Makesurerubberwashersareinserted
ineachendofhose.Attachtaperedendofhose(#8)tohandheldwand(#3).
7
Navajo Model # 1018
PLEASE READ THE FOLLOWING INSTRUCTIONS
COMPLETELY BEFORE BEGINNING!
Our goal is to ensure your installation goes smoothly and safely. Please read these safety
instructionscarefullyandfollowrecommendationsforplumbingandmounting.If, after reading
instruction manual, you determine you do not have the necessary skills and/or tools, we
then recommend a licensed plumbing contractor complete the installation.
If you encounter any problems during installation call Technical Support toll
free at 888-785-7320 before returning item to store.
You will need the following tools:
Level TapeMeasure
Softpencilorfeltpentomarktile Drill(Preferablycordless)
AReciprocatingSaww/metalcuttingblade(Sawzall®) ChannelLocksoradjustablewrench
¼"MasonryDrillBit
3. Removethehandle(s)andtrimcover(s)ofyourexistingvalveexposingthevalvebodyinthewall.
4. Locatethehotandcoldsupplylinesenteringthevalve.Usingareciprocatingsawwithsharpmetal
sawblade,cuttheexistingvalveout,preservingthethreadsofthesupplylinesenteringthevalve.
(Note:youshouldalsocuttheriserwithinthewallsupplyingtheexistingshowerhead.)Carefully
twistandremovethevalve.
5. Unscrewtheoldshowerheadfromthearmandthenunscrewthearm.
6. Itisrecommendedtoextendthewatersupplylinesoutsidethewallcavityparalleltothenished
wall surface. Attach a male threaded tting to each supply line, maintaining 1/4”- 1/2” space
betweenthemalethreadedttingsandthenishedwall.Theopenendofthemalettingshould
pointdown.Foryourconveniencewehaveincluded(2)1/2”90°ttings³.
7. Makecertainthelocation(height/width)ofthestub-outsandconnectingtothemdoesnotinterfere
withthedesiredmountingheightoftheShowerSpa.
8. Markthelocationoftheholesforthemountingbracketmakingsurethebracketislevel.Fora
person5’8”–6’2”tall,werecommend53”fromnishedoorheight�.Beforedrillingholesforthe
bracket, make certain theShowerSpawill rest at againstnished wall surface at thedesired
mountingheightwiththesupplylinesconnected.
9. Drill1/4”holesthroughthewallsurfaceusingamasonrybit.Drillslowlythroughwallsurfaceto
avoidcrackingandchipping.Insertanchorsandsecurelyscrewbrackettowall.Beforeconnecting
thehotandcoldsupplylines,mounttheShowerSpaonthewall,checkingtheheight,andmaking
suretheShowerSpafeelssecure.
10.Connecthotandcoldwatersupplylinestomalethreadedpipe,donotover-tighten.Beforeyou
mounttheShowerSpa,checkthettingstomakesuretheyaresecure.Turnonwaterandcheck
forleaks.Whenttingsareleak-freemountShowerSpaonwall.
11.Holdhandheldmounttodesiredheight,makingsureexiblehosereachesmount.Recommended
4”to6”fromShowerSpaontherightsideoftheunit,soyoucaneasilyremovehandheldwand.
Positionmountatonsurfacemaketwomarkswithpencil.Carefullydrill¼”holesthroughthewall
surfaceusingmasonrybit.Insertanchorsandsecurelyscrewmounttowall.
12.Optional:SealaroundthebodyofShowerSpawithabeadofsilicone.
³Additionalttingsmaybenecessarydependingonyourspecicsituation.
�Thisheightcanvarydependingonseveralfactors(i.e.locationofsupplylines,oldvalveaccess
area,personalpreference,etc).
ATTENTION
ONCE YOUR UNITS IS INSTALLED, IF YOU HEAR A KNOCKING SOUND WITHIN THE UNIT
WHICH SOUNDS LIKE IT IS COMING FROM INSIDE THE WALL, WE HAVE A CHECK VALVE
THAT WILL ELIMINATE THIS KNOCKING. PLEASE CONTACT PULSE SHOWER SPAS AT
1-888-785-7320
We will send you a check valve free of charge.
PULSEuses acUPCcertiedpressurebalancedvalvewhichisdesignedtopreventscalding
andmaintainaconsistentwatertemperature.Ifthereisasuddendropinwaterpressure,(i.e.
ushingtoilet,turningonafaucet,etc.)thevalvewillcompensateforthedropinwaterpressure
byknockingtomaintaintheowrate.Byinstallingthecheckvalve,thepressureismaintained
withinthevalveeliminatingtheknockingsound.