Automatic Drum Washer
MODEL HD1200TXV
Operating Instructions
0020501834
Names of the parts
Reading before using
Unpacking levelling and positioning
Close up
Preparation
Washing method
Practical know-how
Flushing and maintenance
Keys to questions
Wiring Circuit
1
2-4
5-7
8-9
10
11
12-13
14-15
16
17
Wiring Circuit
I1: Power Switch
l2: Soak Switch
l3: Economic Wash Switch
MR: Door Lock
MT: Timer motor
RR: Heating Element
EVP.EVL: Water Valve
P1,P2: Pressure Switch
PCB: Speed Module
THR: Adjustable Thermastat
PS: Drain Pump
PV: Adjustable Speed
M
T
I1
2
B4
B3
B5
2
L
MR
N
C
S.L.
1
1
12
11
L
N
G2
G3
G1
G4
G5
E2
22
24
21
F5
F4
F2
F3
EVP
EVC
S.O.
EVL
F1
I3
2
1
TH36
TH55
D2
MT
PS
R
R
R
TF
D3
B1
B2
D1
D4
A6
A3
V
P
A1
E3
E1
E4
E5
C
THR
M5
M3
M4
H1
H2
H3
M2
M7
M8
M1
B1
B2
B4
C1
C2
C3
PV
C5
C4
B3
B5
B6
B7 B8
PCB
A3
A2
A4
A5
A7
A8
P2
12
14
P1
17
1
Dear Users:
Thank you for your choosing and utilizing Haier products.
Washing Allocating box
Washer Door
Power Wire
Screws of back cover
Drain Hose
Back Cover
Screws for Pack
Drain Hose Clip
Temperature Knob
Spinning Speed Knob
Program Knob
Table Cover
Operating Button
Observing Glass Window
Grounding Terminal
Names of the Parts
Our products are integrated with high-tech, precision and top-level.
It's said that our products are the best of its kind. In order to use
washer properly and in perspective, please read the manual carefully
and operate according to the procedures described as follow.
16
Keys to questions/Guarantee for aftersale service
Keys to questions
Not all the following phenomena are faults, please confirm the following items
before maintenance:
Phenomena
Machine not start up
No water in
Continuos water
injection and discharge
No water discharged
Fierce vibration when
spinning
Stop operation with
program not finished
Stop for a period
during the washing
process?
Items to be confirmed
Power plug fall off or not?
Electricity is out or not?
Machine door tightly closed or not?
Not press down the power button?
Water P less than 0.05MPa?
Water inlet hose bent or not?
Water supply stop or not?
Program button in appropriate position or not?
Machine door closed well or not?
The discharge hose end below 80cm or not?
Discharge hose blocked or not?
Discharge hose end 100cm higher
than the ground?
Fix bolts for packing use are all dismantled?
Work platform is adjusted level?
Load is over the rated 6kg?
Sudden stop to electricity or water?
In the normal soaking process?
In the state of only heating?
Note: to ensure the washing results, when water
T lower than normal T, even though T button at
"*" position the machine will also be heated to
normal T automatically.
2
Reading before using
The independent outlet shall be needed by its power, and the
grounding
terminal of the outlet shall be firmly grounded. You can't
use it without
grounding terminal.
Don't pull the plug out by dragging the power wire.
The user's home shall have the insurance equipment and it's electric
meter, fuses, wires and outlet etc. shall support the biggest electric
current. Avold needing the multioutlet, please don't use with other
appliances at same time. If the supply cord is damaged, it must be
replaced by a special cord or assembly available from the manufacturer
or its service agent.
Please do not touch the washer when you bare feet or there is water on
your hands or your feet.
Please read the documents enclosed carefully. If you transfer the
washer to
other or move it again, please attach the instruction as a
reference. The
advice mentioned here are all for the safety rules,
please read it carefully
before you install and operate. If don't do as
follows, we'll not take charge for
the accidents.
The safety:
1.
2.
3.
4.
5.
6.
7.
15
Flushing and maintenance
Maintenance for no use for a long time
When home-moving
Clean filter (once each month)
If the machine not in use for a long time,
put off the power plug and close the faucet,
open the machine door to prevent any
smell left in it. Let the door slightly open
when not in use.
When home-moving, must install the fixing
blot and anti-vibration channel steel
according to the following steps in order
not to damage the internal parts.
(illustration)
take off the back cover/place the bolt
rubber case for packing use/insert the fix
bolt for packing use/turn tight with the
spanner supplied in the accessories/turn
on back cover.
Remove the profile as shown in figure 1.
Turning and remove the filter in a
counter-clockwise direction as shown in
figure 2.
Clean the filter with water.
Mount the filter in a clockwise direction,
put the profile as it is.
1.
2.
3.
4.
fig.2
fig.1
Do not wash articles that have been previously Cleaned in, washed
in,
soaked in, or spotted with gasoline, dry-cleaning solvents, other
flammable, or explosive substances as they give off vapors that
could
ignite or explode. Do not add gasoline, dry-cleaning solvents,
or other flammable, or explosive substances to the wash water.
These
substances give off vapors that could ignite or explode.
Under certain conditions, hydrogen gas may be produced in a hot
water
system that has not been used for 2 weeks or more.
HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has
not been used for such a
period, before using a washing machine,
turn on all hot water faucets and
let the water flow from each for
several minutes. This will release any
accumulated hydrogen gas.
As the gas is flammab not smoke or use
an open flame during this time.
Don't let kids approach the running washer because the washer
door is
hot when heating. When drain the hot water, please be
carefully in case scald. For the safety, please don't let children play
with the washer and keep the pets far from the machine.
3
Because of the changes of the tap water press, we shall check up
the pumping pipes, tap, draining pipes and the longer pipes carefully
so as to make sure if the junctures are linked fightly before washing.
If some joints get loosed or leaked, we should stop using the washer
and dispose the machine properly.
When choosing washing program, we must turn it clockwise after
disconnected the electricity.
Don't put any heavy, hot or leaking objects on the washer least plastic
parts be deformed.
When first using the washer please let washer running some program
with empty the washer pollute the cloths.
The usage:
The machine can't be installed in the opernair and the place of raining
or snowing, and can't be used in the place of too humidity, if not, it's
easy to form the sweat that can bring about the spark damage and
other accidence. It must be placed far from the hot source and sun,
in case aged for the plastic and rubber. If the machine is wet, it must
be dried, then can be used.
A carpet must not obstruct the ventilation openings in case the wet
can not get out or other safety accidence.
During installation, the washer wires can't be pressed by the foot
and there can't be the problems of broken or turn over.
The hose can't be too long, and its diameter shall be as same as the
original ones, and the height shall be between the 80 -100cm, that
can't be immerged in the water, in case suction phenomenon and
the longer parts must be linked firmly in case leaking.
If the water pipelines are new or haven't be used for a long time,
please let the sewage and rust water out, in case blocking the filter
or contaminating the clothes.
The washer's back can not be put closed the wall tightly or other
furniture.
The drain pipelines are fixed firmly, in case breaking off.
After installation of the washing machine,the power plug should be
accessible during the normal use.
Destroy the carton, don't let lids play, plastic bag and other packing
materiads after the washer is unpacked.
Don't touch the door's inner in case scald, when open the door during
heating and drying.
The installation
8.
9.
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
4.
14
Flushing and maintenance
Flushing
Regularly clean the inlet hose connection and
the filter to avoid blocking by foreign things in
the water.
4.
3.
2.
1.
Each time after washing, close faucet, open
observe window to prevent moisture and
smell. If the machine not in use for a long
time, turn off the power supply, and place
the discharge hose as low as possible,
empty the water in the pump to avoid the
deterioration of water for no use for a long
time.
When go on with any cleaning and maintaining,
should pull off the power plug at first. When
flushing the exterior part and rubber parts of
the machine, only scrub with a piece of cloth
soaked with small amount of soap water. Be
sure not to use solvent and corrodent.
The detergent distribution box should be
cleaned regularly. The box is a are-rotating-
axis type. When cleaning, only need to
rotate it to open and then slightly pull up,
then drag outward (as illustrated) then flush
with the flowing water.
4
Don't wash the foamed rubbers or the same kind of flexibility objects.
There is the function in the program that has the clothes soaked
and does not crinkle it. The clothes are soaked into the water before
dehydrating, if we want it to go on, please tune the program a space.
The selflock insurance equipment is set on the washer door. Don't
open the door until washer stop or disconnect the electricity for 2-
3 min, in case getting the door damaged. When there is water in
the washer, don't open the machine door.
Don't put too much clothes in the washer in case these are nipped
between the inner rub and observing glass window and harm the
clothes.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
13
strong washing
mode-mainly
for cotton
fabrics
Programme-setting mode
1
2
3
4
5
6
7
A
B
C
D
E
F
I
II
III
IV
V
12
32
4
28
28
10
12
stop
6
10
18
10
6
6
stop
time (approximate)(min)
medium washing
mode-mainly
for chemical
fabrics
soft-washing
mode-mainly for
wool and
cashmere
Wash time
Different types of clothes correspond to different temperature, fuction,
washing time, etc, which is chosen in the washing. The following
table
shows the pure washing time needed with the normal, water
pressure,
electric voltage under different program without heating. It
is only for your
reference.
8
8
4
4
2
stop
The washer is family one, so only design for machine washing.
When washing, please refer to the washing method on the clothes
label, make sure if it can be machine was h i n g an d if it c a n wash
after dry.
Don't use too much detergent in case harm the texture objects.
Please using as the direction.
We can't put the bleaching powder into wrong box, or it may have
the clothes yellow.
After washing finished. Please pull out the plug turn off the tap in
case leaking phenomenon. And clean the pad's interlining well in
case the dirty sticks the clothes again or make the window pad
surface mildew.
When the washer is not using, please open the machine door
slightly in case peculiar smell and the machine door blocking. Don't
put the plastic bag over the washer in case the wet can't be get out.
Before washing, please put the bits and pieces well, such as zips,
buckles, belts etc, and sew the frazzle. The exiguous should be
put into washing bag or pillow bag to wash in case the thin dropped
into the gap between the washer and out tub.
Any stiff may cause the big damage, such as coins, fibulas, nails,
screws and stones etc. Remember never put these into washer.
5
Unpacking Levelling and positioning
The shock absorption lumps must be r
emoved
wholly, include foamy pedestal
and shock lump
for transport in the bottom of the washer (the
shock lump for transport is sure to be taken
out)
The accessories and data are put in the
plastic bag in the washer.
Fig.2
Fig.3
Fig.4
The pack screws, rubber sleeve shall be keep
well in order to prepare to use in future(see
page 15)
Remove the whole Package (fig. 1)
Check the accessories and data
Check attachments and materials.
Remove the Pack Screws (fig. 2)
Attention:
Name
Plastic
plugs
Drainage
holder
Water
hose
Quality
certificate
Adjustment
spanner
Operational
manual
Qu'ty
Model
HD1206TXV
11
1
1
1
3
The pack screws is to fix the suspended ob-
jects in the washer inner. Before using, we must
take off the back cover with the wrench , sec-
ond remove the three pack screws on the
washer back cover, third put down the rubber
sleeve, then put on the back cover as before.
1
12
Practical know-how
How to save water during the washing
How to use detergents
1. Wash the clothes collectively
2. The actual load of clothes don't exceed the rated one.
3. The detergent added should be appropriate, not too much in amount.
4. Prewash the dirtiest pieces which then are washed with other clothes
together.
5. For the less dirty clothes, can reduce consumption of the detergents.
The 3 compartments marked 1,2,3 should be used
as followes:
1: Prewash detergent.
2: Wash Detergent
3: Conditioner, starch ,scents
remember that it is important to use the right amount
of soap powder or liquid for the type of laundry you
are washing;the amount of detergent you use
depends on a number of factors:
when using concertrated detergents,remember to keep to the manufacturer's
instructions using only the measuring cups supplied with the packet
use more detergent in the case of very hard water(more than 21 .F),but
remember to maintain the proportion between the prewash and wash cycles
Liquid detergent
The liquid detergents currently available on the market may be used with the
washing machine. Use compartment 2 for very dense liquid detergents.follow
the manufacture's instructions when using liquid detergents sold with the ball
detergent washing machine together with the laundry.
the prewash cycle may not be used with liquid detergents.
1 and 1/2 measuering cup
1/2 measureing cupnormally soiled
softeners(see note"3")
Compart3
Compart2 normal wash
Compart prewash
Laundry
The following table will guide you:
water hardness: if the water in your area has a high calaium content,we
recommend using a antilimestone additive
degree of dirtiness: increase the amount of soap power used in the case
of heavily soiled laundry.
laudry load:the smaller the load the less soap powder you will need to use
1
2
6
6
100cm
80cm
5
Put and adjust the washer horizontally
Draining hoses
The length of the draining hose: 1800mm,
the out diameter of the nozzle: 28mm, the
inner diameter: 20mm.
There are the adjusting feet under the
washer. Before using, we shall adjust the
washer horizontally (fig. 5)
We'II provide you the free installment service
(only charge the material fee), because you
buy our washer. If the user like to install by
yourself, please do as follows:
The draining high must be between 80- 100cm
an has e water-proof measure.(in case
washer lose water but can't drain) (fig.6) we
may use the joint clips on the back of the
machinetofixthesoftpipeonthebackof
washer.
11
Washing Method
1. Loading of clothes
When the program chosen is finished, the machine will stop
operating
automatically, after 2 minutes press out the power key
and open the door, take out the clothes, and close the faucet.
6. Washing close
Press down power key, the machine will operate by the set program.
5. Washing
Choose function keys according to needs ( refer to Page 9 ) If no needed,
all the keys are in release status.
4. Choose function key
(
1)Before setting the mode, must make press key of the power switch
at
the OFF status.
Note:
To get the best washing result, the best program-setting mode is chosen
according to the types of clothes. The set modes are printed on the
handle of detergent distribution box and turn clockwise the program
switch to make the indicating point against the set mode to be chosen.
3. Set the washing program
Drag out the detergent distribution box and add adeguent detergent,
softener, bleaching agent into the corresponding channels as required
and then slightly close the box.
Open the machine door, and evenly place the clothes treated into the
washing machine and close the door.
2. Adding detergent
When choosing the program in the 2 areas of medium/soft wash,
before program go to the spin dry/drain, clothes will be soaked
against wrinkles, then if need to take out the precious items, please
choose the draining program manually. If other clothes is needed
to be spin dry, manually switch the program to spin dry. ( For wool
and chemical fabrics, after finishing wash, if not taken immediately,
wrinkles will happen on the fabrics, so soaking program set in
these two areas.)
(2)
Attach the end of supply hose to your water tap spigot.
Ensure the correct ass end of the hose is attached to
your water supply for proper fit.
Note that the ends are different. Also ensure that you
match up cold spigot with cold connection on machine
(notice "C" and "H" indications next to connections on
machine). Now connect hot to hot. If supply hose
connections don't fit your spigot, try your local home
center to match up correct connections. Home centers
also have "Y" connectors and couplings which enable
you to connect the machine to your sink s faucet.
7
The grounded cord:
²When the washer is using, it must link the
ground well.
² If the washer has the grounded cord in its
outlet, please don't use prepared wire.
² If the washer has not the grounded cord in
its outlet, we must use the prepared wire
to link from the grounded terminal on the
upper right of the washer back, then make
sure this line shall link the ground well.
10
Preparation
Clothes type
Biggest load
Non-fading
clothes
6kg
Soft fabric
2kg
Wool fabric
1kg
Textile
2.5kg
1. Power Resource: Connect the power resource
2. Connected the water resource: Open the tap, the water should be pure.
Attention: Each time before the washer work, first should open the
tap to check up the joints between the tap and pumping hose, check
if there is leaking phenomenon in case the accidence.
3. The Clothes' Disposal
²
The classification according to the clothes' types and dirty degrees:
The clothes' types: Cotton, Chemical Fiber, Silk.
² Make a different between the white clothes and color clothes. If wanted
to Wash these together, first should proceed a test with manual, be sure
if adhesion strength is ok, the fade clothes should
wash separately.
-- Put the objects (coins, money etc.) out the pack, and has the pack
outside.
-- When washing the non-rim or loosing threads' clothes, must put it
into the string bag in case clothes damage (Suggestion: don't use
the machine washing).
-- Sew the worn, loosing button, slide fastener and close the bag.
-- It should be put in loosely for the big objects, such as the sheet,
tablecloth etc. don't fold.
-- Have the shirt's inner outside.
4. Put the detergent into
Open the allocating box, put the detergent into.
5. The best washing load
Attention: The prepared wire can't link with
the water pipe or the central heating pipe.
7
If the washer is far from the water source,
we could longer the draining hose or lineup
through the wall. (but the hose can't be longer
than 5m, the diameter of longer hose shall be
as same as the original hose, the part of the
longer hose shall be firm and can't leak)
We can utilize the support to install the water
pipe. (fig.7)
Attention: the draining nozzle can't immerge
into the water
8
Close up
30
x
The nearsighted figure of operating plate attaches
as follows. Please refer the accessory page to know
each function.
The washer's knob is "the inner type". You can only
push the center of the knob slightly, then it can spring
out.
Washing Allocating Box
There is the manual on the handle of the washing
allocating box. Open the box, we can see that there
are three closets in it: 1,2, And 3.
The closet 1: The pre-washing detergent
The closet 2: The washing detergent
The closet 3: The soft, opsonin, and essence etc.
Turn this knob can select the required spinning speed
(400~1200r/min selectable).
Spinning speed knob
1
2
700
600
550
9
Close up
ON
OFF
Power Button
Push the button down, the washer connect the
electricity automatically. Get the button up, the
washer cut-off the electricity.
Soak button
Economic wash button
Pressing this button will reduce the consumption of
water during bleaching under intense wash. It is rec-
ommended that this program be used when doing a
small laundry load.
Do not forget to reduce the amount of detergent used.
When this button is pressed, the machine will auto-
matically stop running at the softening cycle prior to
the spinning cycle during chemical fiber and wool
washing, and the laundry is soaked in water. Release
this button, the program will stop after the spinning cycle
ends. Using this function can reduce the creasing of
valuable clothes from spinning.
Washing Program Knob
We can get the most proper program for the washing
clothes by turning the knob clockwise. Remember: It
must be operated to choose the program on the state
of turn off.
Washing Temperature Knob
As turning the knob, we can get the washing
temperature properly. The heat temperature can
adjust between the 30-90
o
C. When the knob point
"*", it means the cold washing.
Power light
The meter is red and point out if there is electricity
on the washer. When the meter light, the washer
get power.
/