Christie Crimson WU31 Technical Reference

Brand: Christie

Model: Crimson WU31

Type: Technical Reference

This manual is also suitable for

Technical Reference

020-102661-04

Crimson and Crimson Mirage

Status System

NOTICES

Cop

yright

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this

document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary

depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on

information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied

warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection

with the performance or use of this material. Manufacturing facilities in Canada and China are ISO 9001 certified. Manufacturing facilities in Canada are also

ISO 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie. In

addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the

warranty does not cover:

Problems or damage occurring during shipment, in either direction.

Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or use

of a product with any non-Christie interface device.

Problems or damage caused by misuse, improper power source, accident, fire, flood, lightning, earthquake, or other natural disaster.

Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a Christie

authorized repair service provider.

Use of third party product enclosures for environmental protection during outside use must be approved by Christie.

Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed, modified or

approved by Christie for such use.

Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is protected from

precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient temperature set

forth in the specifications for such product.

Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold

by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or

(ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and in

accordance with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at the user’s own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

ENVIRONMENTAL

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol

means that electrical

and electronic equipment, at their end-of

-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and according

to local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the

environment we live in!

Content

Crimson

status system..............................................4

Model name.......................................................4

Product documentation................................................4

Related documentation..............................................5

Status system states.................................................5

Configuration Group (SST+CONF?)........................................ 5

System Group (SST+SYST?)............................................ 6

Signal Group (SST+SIGN?)............................................ 12

Light Group (SST+LGHT?).............................................13

Version Group (SST+VERS?)........................................... 15

Cooling Group (SST+COOL?)........................................... 17

Temperature Group (SST+TEMP?)........................................20

Serial Group (SST+SERI?).............................................23

Crimson and Crimson Mirage Technical Reference–Status System 3

020-102661-04 R

ev. 1 (07-2020)

Crimson status system

This guide contains information about the v

alues and fault conditions that can be reported by the

status system on Crimson devices.

The status system provides an overview of the device at the current point in time. It contains a

number of groups, which contain a set of status items. Each status item represents a component or

sub-component of the system. Obtain specific details regarding a warning or error for a status item

using the log system.

The numbers next to the status items in this guide correspond directly to the status item index within

each group.

Model name

• Crimson HD25

• Crimson WU25

• Crimson HD31

• Crimson WU31

• Mirage HD25

• Mirage WU25

Product documentation

For installation, setup, and user information, see the product documentation available on the Christie

Digital Systems USA Inc. website. Read all instructions before using or servicing this product.

Crimson HD25, Crimson WU25, Crimson HD31, Crimson WU31

1. Access the documentation from the Christie website:

• Go to this URL:bit.ly/2nOplCa.

• Scan the QR code using a QR code reader app on a smartphone or tablet.

2. On the product page, select the model and switch to the Downloads tab

Crimson and Crimson Mirage Technical Reference–Status System 4

020-102661-04 R

ev. 1 (07-2020)

Mirage HD25, Mirage WU25

1. Access the documentation from the Christie website:

• Go to this URL:bit.ly/2C6H4HZ.

• Scan the QR code using a QR code reader app on a smartphone or tablet.

2. On the product page, select the model and switch to the Downloads tab

Related documentation

Additional information on the projector is available in the following documents.

• Crimson and Mirage Installation and Setup Guide (P/N: 020-102647-XX)

• Crimson and Mirage User Guide (P/N: 020-102649-XX)

• Crimson and Mirage Product Safety Guide (P/N: 020-102648-XX)

• Crimson and Mirage Specifications Guide (P/N: 020-102724-XX)

• Crimson and Mirage Service Guide (P/N: 020-102733-XX)

• Crimson and Mirage Serial Commands Guide (P/N: 020-102660-XX)

Status system states

The status system has three states to indicate the health of the device.

OK No known issue

Warning A problem with this item should be addressed.

Error A problem with this item prevents the projector from properly

displa

ying video or turning on the projector.

Configuration Group (SST+CONF?)

The Configur

ation Group provides values and fault conditions for configuration-related items in

Crimson.

# Status State Value Description

0 Projector Model <projector model> Displays the model for the Crimson

projector

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 5

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

Unknown Cannot retrieve the model information.

Jig Mode Reserved for engineering use.

1 Projector S/N <serial number> Displays the serial number of the

projector

Unknown The storage device containing the

information is inaccessible or the data on

the device is corrupted.

2 Output Resolution <horizontal>x<vertical> Displays the native output resolution of

the projector

3 Projector Build Date

<YYYY>/<MM>/<DD> Displays the build date of the projector.

Unknown The storage device containing the

information is inaccessible or the data on

the device is corrupted.

System Group (SST+SYST?)

The S

ystem Group provides values and fault conditions relating to the system and its health for

Crimson.

# Status State Value Description

0 Projector Hours <hours>:<minutes> Displays the total amount of time that

the projector has been on (including

arm up and cool down times).

This does not include the amount of time

required to cool down the electronics

when turning off the Keep Electronics on

in Standby option while the projector is

already in standby.

N/A Cannot retrieve or update the value.

1 Pitch/Roll <pitch value>/<roll

alue>

Provides the physical orientation of the

projector:

• A negative pitch means that the

projector is pointing down.

• A negative roll means the projector

is tilted counter clockwise as seen

from the rear.

Communication Fault Information is not available due to a

hardw

are fault.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 6

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

Lens Motor Horizontal-Axis

Lens Motor V

ertical-Axis

Lens Motor Zoom- Axis

Lens Motor Focus- Axis

Calibrating Currently calibrating the lens motor.

Calibrated The motor range has been properly

calibr

ated.

Unknown The status of the motor is unknown

because a problem occurred in the

upstream communication path.

Uncalibrated The range for the current lens has not

been determined and/or the reported

position on the axis ma

y be inaccurate.

Failed During reset or calibration, an error was

detected related to the motor and/or

sensor

9 Built-In Self Test

N/A The built-in self test has not been

ecuted yet.

Passed The built-in self test completed

successfully

Failed The built-in self-test failed.

10 System ID Board OK The device has been properly detected

and initializ

ed.

Unknown The status of the device is unknown.

Communication Fault Cannot communicate with the device.

Invalid Data The information on the device is missing

or corrupted.

11 Housekeeping Board OK The device has been properly detected

and initializ

ed.

Unknown The status of the device is unknown.

Communication Fault The device failed to respond or provided

a bad response to a command while the

light source is on.

The projector remains on until AC power

is remo

ved, even if this warning

condition is fixed.

Detection Fault Cannot read the device hardware

information.

Initialization Fault Cannot properly initialize the device.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 7

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

Communication Fault The device failed to respond or it

pro

vided a bad response to a command

while the projector is in standby mode.

12 Keypad Display

Auto Detect The projector is attempting to detect the

presence of the k

eypad display device.

Programming Programming the device with the correct

firm

ware.

OK The device has been properly detected

and initializ

ed.

Detection Fault Cannot detect the keypad display device.

Unexpected Behavior The device is not responding correctly.

Upgrade Failed The device failed to upgrade properly.

13 Power Supply OK The power supply has been properly

detected and initializ

ed.

Unknown The status of the power supply is

unknown due to an upstream

communication fault.

Fan Problem The power supply reports a fan failure

but no o

ver temperature shutdown or

high temperature alarm is reported.

Overtemperature The power supply reports a high

temper

ature alarm but reports no fan

failure.

Overtemperature/Fan

Problem

The power supply reports both a high

temper

ature alarm and a fan failure.

Communication Fault Communication either timed out or an

error occurred in the tr

ansmission/

reception of data.

Detection Fault Communication timed out at startup.

Overvoltage Detected The power supply reports an over

oltage shutdown condition.

Overcurrent Detected The power supply reports an over

current shutdown condition.

Overtemperature The power supply reports an over

temper

ature shudown.

Overtemperature/Fan

Problem

The power supply reports an over

temper

ature shutdown and fan failure.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 8

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

Control Fault The power supply reports an internal

circuit failure.

AC Input Low The power supply reports the AC input is

too low for full power mode.

27 Power Supply Input Voltage Limited Mode The AC power cable is plugged into inlet

Full Mode The AC power cable is plugged into inlet

29 Lens ID Detected The lens was detected.

Unknown The communication path to the lens is

not working; therefore, the state is

unknown.

Not Detected Cannot detect the lens.

30 Main Control Board OK The main control board has been

initializ

ed at least once and is known to

be OK.

Unknown The main control board status is

unknown because it has not been

powered up y

et.

Initialization Fault Cannot successfully program the main

control board.

32 Power Supply Output Voltage <voltage>V Displays the output voltage reading

when the housek

eeping board (HKB) is

ready.

Unknown The status of this output is unknown

because the power supply cannot be

communicated with.

46 Status LED Board OK The status of the status LED board (SLB)

is OK.

Unknown Cannot determine the status of the

status LED board (SLB) because the

backpane (C4BP) is nonfunctional.

Communication Fault Cannot communicate with the status LED

board (SLB).

47 Side Panel NFCT OK The side panel near field communication

tag (NFCT) is OK.

Unknown The side panel near field communication

tag (NFCT) status is unknown because

the integr

ated keypad board (IKB) is

non-functional.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 9

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

Not Detected Cannot write to or read from the side

panel near field communication tag

(NFCT).

48 Backplane OK The backplane has been properly

detected and initializ

ed.

Detection fault Cannot read the backplane hardware

information.

Initialization fault Cannot properly initiate the backplane.

Runtime fault The backplane experienced an

unreco

verable failure during runtime.

49 Image Processor

Off The image processor is in standby

without an

y cached errors or warnings.

OK The image processor has been properly

detected and initializ

ed.

Unknown Cannot determine the image processor

status due to an upstream issue.

Detection fault Cannot read the image processor

hardw

are information.

Initialization fault Cannot properly initialize the image

processor

Runtime fault The image processor experienced an

unreco

verable failure during runtime.

Formatter-Red

Formatter-Green

Formatter-Blue

Off The formatter is in standby without any

cached errors or w

arnings.

OK The formatter has been properly

detected and initializ

ed.

Unknown Cannot determine the formatter status

due to an upstream issue.

Power Bad The formatter detected an unexpected

power glitch and has started the process

of parking the DMD

. This is often

recoverable.

Detection Fault Cannot read the formatter hardware.

Initialization Fault Cannot properly initialize the formatter.

Runtime Fault The formatter experienced an

unreco

verable failure during runtime.

Option Card 1

Option Card 2

Off The option card is in standby without

y cached errors or warnings.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 10

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

OK The option card has been properly

detected and initializ

ed.

Not Present An option card is not installed in this

slot.

Unknown Cannot determine the option card status

due to an upstream issue.

Detection fault Cannot read the option card hardware

information.

Initialization fault Cannot properly initialize the option

card.

Runtime fault The option card experienced an

unreco

verable failure during runtime.

85 Color Sensor Board

OK The device has been properly detected

and initializ

ed.

Unknown The status of the device is unknown.

Communication Fault Cannot communicate with the device.

Detection Fault Cannot detect the color sensor board.

Initialization Fault Cannot properly initialize the color

sensor board.

113 Combine ID Board OK The device has been properly detected

and initializ

ed.

Unknown The status of the device is unknown.

Not Detected Cannot detect the device.

Initialization Fault Cannot initialize the device.

Communication Fault Cannot communicate with the device.

114 Combiner Driver OK The combiner has been properly

detected and oper

ating correctly.

N/A The status of the combiner is not

vailable.

Upgrading The combiner is in the process of a

firm

ware upgrade.

Do not turn off the projector while the

upgrade is occurring.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 11

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

The upgrade should not take longer than

one minute and occurs immediately

following a main system softw

are

upgrade.

Detection Fault Cannot detect the combiner.

Upgrade Failure Cannot upgrade the combiner firmware.

The projector will not turn on.

Signal Group (SST+SIGN?)

The Signal Group pro

vides values and fault conditions relating to the video signal status for Crimson.

# Status State Value Description

HDBaseT Input

Card 1 - Input 1

Card 1 - Input 2

Card 1 - Input 3

Card 1 - Input 4

Card 2 - Input 1

Card 2 - Input 2

Card 2 - Input 3

Card 2 - Input 4

Not Present Either the card is not present or the card

does not ha

ve a single input port.

<input type> (No Signal) No signal is detected.

Where <input t

ype> : {DP, HDMI, DVI,

3G-SDI}

<input type>, <active

window>@ <v

-sync rate>

(<status>)

Where

<input type> : {DP, HDMI, DVI, 3G-

SDI}

<active window> :

<v-sync rate> : the input frame rate,

in Hz (##.##Hz)

<status> : {“Master”, “No signal”,

“Inactive”, “Locked”}

@ <v

-sync rate> (<status>)

Where

<input type> : {DP, HDMI, DVI, 3G-

SDI}

<active window> :

<v-sync rate> : the input frame rate,

in Hz (##.##Hz)

<status> : {“Unlocked”, “Out of

phase”}

50 Output Frequency

<rate>Hz Where <rate> : the output frame rate,

in Hertz

If the input frequency does not match

the output frequency

, Free Running @

XX.YYHz is displayed.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 12

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

N/A No video is being displayed.

51 Frame Locked N/A No video is being displayed or an

internal test pattern is being displa

yed.

Locked The output is locked to the selected

input(s).

Unlocked The output is not locked to the selected

input(s).

52 3D Sync N/A There is no 3D signal or 3D mode is set

to Off

Valid 3D Sync Detects a valid external 3D sync.

Internal 3D Sync The system is using the internal v-sync

signal because the video is configured as

a Dual-

Input. External sync is ignored.

Valid HDMI 3D Sync Properly detects the built-in HDMI 3D

sync signal.

Invalid 3D Sync (using internal

sync)

Detects an external 3D sync but it is not

lock

ed and/or in phase with the 3D video

signal(s). The system is using the

internal v-sync signal instead but may

have L/R swapped.

No 3D Sync (using internal sync) Cannot detect an external 3D sync. The

system is using the internal v

-sync

signal instead but may have L/R

swapped.

53 TSIC Connection

Alias IP: <IP address> Displays the IP address used to

communicate with the projector through

the SDV

oE network.

N/A Either the card is not present or is not

powered.

Light Group (SST+LGHT?)

The Light Group pro

vides values and fault conditions relating to the light source status for Crimson.

# Status State Value Description

0 Combiner State On The combiner is on.

Off The combiner is off.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 13

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

Warming Up The combiner is in the process of turning

on.

Cooling Down The combiner is in the process of cooling

down.

Overtemperature The combiner has turned off due to the

thermal fuse being tripped.

Overcurrent Detected The combiner has turned off due to over

current protection.

Initialization Fault The combiner has turned off

unexpectedly during while the projector

is w

arming up/initializing..

Runtime Fault The combiner has turned off

unexpectedly while in the projector is

on.

1 Combiner Hours <hours>:<minutes> (h:m) Displays the total amount of time that

the combiner has been on.

Unknown The combiner hours are unknown

because the combiner cannot be

communicated with.

228

229

230

231

232

237

242

247

Diode current (Red1)

Diode current (R

ed2)

Diode current (Red3)

Diode current (Red4)

Diode current (Green

+Red A)

Diode current (Green

+Red B)

Diode current (Green

+Red C)

Diode Current (Blue)

<current>mA Displays the current being drawn by the

diode(s).

Unknown Cannot retrieve the value due to a

communication error with the combiner

firm

ware.

Off The diode(s) is currently off.

251 Combiner TEC Current <current>mA Displays the current being drawn by the

thermal electric cooler (TEC).

Unknown Cannot retrieve the value due to a

communication error with the combiner

firm

ware.

Off The thermal electric cooler (TEC) is not

running.

Detection Fault Cannot detect a current. It appears the

TEC connector is unplugged.

252 Combiner Phosphor

Wheel

<RPM>RPM Displays the phosphor wheel RPM.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 14

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

Off The phosphor wheel is not spinning.

<RPM>RPM - Low RPM The combiner has shut down because

the phosphor wheel RPM is too low

253 Combiner Diffuser Wheel

<RPM>RPM Displays the diffuser wheel RPM.

Off The diffuser wheel is not spinning.

<RPM>RPM - Low RPM The combiner has shut down because

the diffuser wheel RPM is too low

254 Combiner

Communication

OK The combiner communication path is

good.

Communication Fault A communication failure has occurred

between one of the following:

•

The main software and the

combiner firmware

• The combiner fan board and the

driver board

• The combiner fan board and other

peripheral

Version Group (SST+VERS?)

The V

ersion Group provides values and fault conditions related to software and hardware versions for

Crimson.

# Status State Value Description

0 Main Control Board SW Version <version> Displays the software version

running on the main control

board.

Unknown Cannot determine the software

ersion information.

1 Main Control Board HW Version

<name>.<level>.<mod> <name> = Short name of the

board

<lev

el> = Version of the board

<mod> = Modification level of

the board

Detection Fault Cannot read the board type

information.

2 Backplane HW Version <name>.<level>.<mod> <name> = Short name of the

board

<lev

el> = Version of the board

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 15

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

<mod> = Modification level of

the board

This information is cached while

the projector is in standb

N/A The backplane has never been

turned on or initializ

ed.

3 Image Processor HW Version

<name>.<level>.<mod> <name> = Short name of the

board

<lev

el> = Version of the board

<mod> = Modification level of

the board

This information is cached while

the projector is in standby.

N/A The image processor board has

nev

er been turned on or

initialized.

Formatter-Red HW Version

Formatter-Green HW Version

Formatter-Blue HW Version

<name>.<level>.<mod> <name> = Short name of the

board

<lev

el> = Version of the board

<mod> = Modification level of

the board

This information is cached while

the projector is in standby.

N/A The formatter has never been

turned on.

Option Card 1 HW Version

Option Card 2 HW V

ersion

<name>.<level>.<mod> <name> = Short name of the

board

<lev

el> = Version of the board

<mod> = Modification level of

the board

This information is cached while

the projector is in standby.

N/A The option card has never been

turned on or initializ

ed.

17 Power Supply HW Version

<hardware version>.<boot

ersion>.<main version>

<hardware version> = Hardware

version of power supply

<boot version> = Version of

power supply bootloader

<main version> = Version of

power supply main firmware

Unknown Cannot retrieve the hardware

ersion.

18 Housekeeping Board HW Version

<name>.<level>.<mod> <name> = Name of the board

(such as HKBC)

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 16

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

<level> = Hardware version of

the board

<mod> = Modification lev

el of

the board

Unknown Cannot retrieve the hardware

ersion.

19 Keypad Display HW Version

<name>.<level>.<mod> <name> = Name of the board

(such as IKB)

<lev

el> = Hardware version of

the board

<mod> = Modification level of

the board

Unknown The board is not ready yet so

the hardw

are version has not

been retrieved.

35 Combiner Driver HW Version

<version> Displays the hardware version of

the combiner fan.

Unknown Cannot retrieve the hardware

ersion.

56 Color Sensor Board HW Version

<version> Displays the hardware version of

the color sensor board.

Unknown Cannot retrieve the hardware

ersion.

60 Combiner Fan SW Version

<version> Displays the firmware version

running on the combiner fan

board.

Unknown Cannot retrieve the firmware

ersion.

61 Combiner Fan HW Version

<version> Displays the hardware version of

the combiner fan board.

Unknown Cannot retrieve the hardware

ersion.

Cooling Group (SST+COOL?)

The Cooling Group pro

vides values and fault conditions related to cooling and fans for Crimson.

# Status State Value Description

Intake A (Fan 1)

Intak

e B (Fan 2)

Intake C (Fan 3)

<tach> RPM Displays the current

tachometer reading.

Off Fan is off.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 17

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

Unknown The tachometer reading is

una

vailable.

Off - Overridden Fan is off. The fan speed

has been changed from its

default recommended

alue.

<tach> RPM - Overridden Fan is on. The fan speed

has been changed from its

default recommended

alue.

<tach> RPM - Low RPM Fan tachometer reading is

lower than the minimum

recommended speed.

or the low RPM threshold,

see Crimson and Mirage

Specifications Guide (P/N:

020-102724-XX).

Card Cage Intake (Fan 26)

Card Cage Exhaust (Fan 25)

<tach> RPM Displays the current

tachometer reading.

Off Fan is off.

Unknown The tachometer reading is

una

vailable.

<tach> RPM-Low RPM Fan tachometer reading is

lower than the minimum

recommended speed.

or the low RPM threshold,

see Crimson and Mirage

Specifications Guide (P/N:

020-102724-XX).

Off - Overridden Fan is off. The fan speed

has been changed from its

default recommended

alue.

<tach> RPM - Overridden Fan is on. The fan speed

has been changed from its

default recommended

alue.

12 Liquid Cooling Flow Meter

<value> L/min Displays the amount of

liquid flowing past the

sensor

Off Liquid cooling is off.

Unknown The tachometer reading is

una

vailable.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 18

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

<value> L/min - Flow Impeded The flow reading is lower

than the minimum

recommended threshold.

or the low RPM threshold,

see Crimson and Mirage

Specifications Guide (P/N:

020-102724-XX).

13 Liquid Cooling Pump

<tach> RPM Displays the current

tachometer reading.

Off Fan is off.

Unknown The tachometer reading is

una

vailable.

<tach> RPM - Low RPM Fan tachometer reading is

lower than the minimum

recommended speed.

Intake D (Fan 4)

adiator A (Fan 5)

Radiator B (Fan 6)

Radiator C (Fan 7)

Radiator D (Fan 8)

Radiator E (Fan 9)

Radiator F (Fan 10)

<tach> RPM Displays the current

tachometer reading.

Off Fan is off.

Unknown The tachometer reading is

una

vailable.

Off - Overridden Fan is off. The fan speed

has been changed from its

default recommended

alue.

<tach> RPM - Overridden Fan is on. The fan speed

has been changed from its

default recommended

alue.

<tach> RPM - Low RPM Fan tachometer reading is

lower than the minimum

recommended speed.

or the low RPM threshold,

see Crimson and Mirage

Specifications Guide (P/N:

020-102724-XX).

101 Liquid Cooling Pump (Combiner)

<tach> RPM Displays the current

tachometer reading.

Off Fan is off.

Unknown The tachometer reading is

una

vailable.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 19

020-102661-04 R

ev. 1 (07-2020)

# Status State Value Description

<tach> RPM - Low RPM Fan tachometer reading is

lower than the minimum

recommended speed.

or the low RPM threshold,

see Crimson and Mirage

Specifications Guide (P/N:

020-102724-XX).

103

104

105

106

107

108

109

110

111

113

114

Exhaust A (Fan 17)

Exhaust B (Fan 18)

Exhaust C (Fan 19)

Phosphor Wheel Heatsink (Fan 16)

Light Engine Exhaust Blower (Fan 24)

Light Engine Exhaust A (Fan 11)

Light Engine Exhaust B (Fan 12)

Combiner Fan (P308)

Combiner Fan (P309)

Exhaust D (Fan 13)

Exhaust E (Fan 14)

<tach> RPM Displays the current

tachometer reading.

Off Fan is off.

Unknown The tachometer reading is

una

vailable.

Off - Overridden Fan is off. The fan speed

has been changed from its

default recommended

alue.

<tach> RPM - Overridden Fan is on. The fan speed

has been changed from its

default recommended

alue.

<tach> RPM - Low RPM Fan tachometer reading is

lower than the minimum

recommended speed.

or the low RPM threshold,

see Crimson and Mirage

Specifications Guide (P/N:

020-102724-XX).

Temperature Group (SST+TEMP?)

The T

emperature Group provides values and fault conditions for temperature-related items in Crimson.

# Status State Value Description

2 Air Intake Temperature <value> °C Displays the current

temper

ature of the sensor.

Unknown Temperature reading is

una

vailable.

<value> °C - Low

emperature

Temperature is sitting inside

the warning band.

<value> °C - High

emperature

Temperature is sitting inside

the warning band.

<value> °C - Too Hot

(shutdown)

Temperature is exceeding the

error threshold.

Crimson status system

Crimson and Crimson Mirage Technical Reference–Status System 20

020-102661-04 R

ev. 1 (07-2020)

Page is loading ...

Christie Crimson WU31 Technical Reference

Brand: Christie

Model: Crimson WU31

Type: Technical Reference

This manual is also suitable for

Download PDF

report

Christie Crimson WU31 Technical Reference

This manual is also suitable for

Christie Crimson WU31 Technical Reference

Related papers

Other documents