Contec PWA-65AWD9 is a switching AC adapter with a rated input voltage of 100-240VAC and a rated output voltage of +19VDC 3.42A. It has a permissible momentary blackout of 5ms or less and a dielectric strength of 3.0kVAC for one minute. The insulation resistance is greater than 6.132GΩ (500VDC). It can be used in environments with temperatures ranging from 0 to 40°C and humidity ranging from 20 to 80%RH (no condensation). It is resistant to vibration (10 to 60Hz / 0.
Contec PWA-65AWD9 is a switching AC adapter with a rated input voltage of 100-240VAC and a rated output voltage of +19VDC 3.42A. It has a permissible momentary blackout of 5ms or less and a dielectric strength of 3.0kVAC for one minute. The insulation resistance is greater than 6.132GΩ (500VDC). It can be used in environments with temperatures ranging from 0 to 40°C and humidity ranging from 20 to 80%RH (no condensation). It is resistant to vibration (10 to 60Hz / 0.
Product Guid
e
CONTEC CO.
,
LTD.
3-9-31
,
Himesato
,
Nishi
y
odo
g
awa-ku
,
Osaka 555-0025
,
Ja
p
an
https://www.contec.com
/
No part of this document may be copied or reproduced in any form by any means
without prior written consent of CONTEC CO., LTD.
NA07297 (LYYB552) 06102020_rev2 [03062020] June 2020 Edition
SWITCHING AC ADAPTER (19VDC 3.42A)
PWA-65AWD9
Thank you for purchasing this product. The product you have purchased consists of the
following items.
Check, with the following list, that your package is complete.
If you find any item either missing or damaged, please contact the sales representative you
purchased the product from.
Contact your retailer if you have any technical question.
1. About the Product
This product is the AC adapter for input: 100 - 240VAC and output: +19VDC 3.42A.
2. Product Configuration
This product consists of the items listed below.
Check, with the following list, that your package is complete.
AC adapter...1 AC power cable
(100VAC, 3pin) *1
Product Guide...1 Warranty Certificate...1
Serial Number Label...1
*1 This AC power cable is for the voltage of the 100VAC or less. It might be necessary
to get a particular cable to match the power voltage or outlet shape that you are using.
3. Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
This document provides safety information using the following symbols to prevent
accidents resulting in injury or death and the destruction of equipment and resources.
Understand the meanings of these labels to operate the equipment safely.
DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury or in property damage.
Handling Precautions
WARNING
Do not use the product in locations exposed to a flammable or corrosive gas. It may
cause explosion, fire, electrical shock, or malfunction.
If you sense abnormality (smoke, odor, or noise), immediately unplug the power cord
from the wall outlet and contact the CONTEC sales representative or sales office.
To avoid electrocution do not use the product with a wet hand.
Be sure to connect the product to the stipulated power supply voltage. Connecting to a
different voltage might cause a fire or electrical shock.
Do not use the product with the other power device. It may cause fire or malfunction.
When the cable or main body is damaged, stop using and repair it immediately. Using it
as it is may cause fire, electrical shock or malfunction.
Never disassemble or modify the product or replace its parts in order to prevent electrical
shock, fire, or malfunction. CONTEC reserves the right to refuse servicing the product
modified by the user. When any part of the product needs to be replaced at the expira-
tion of its life or due to breakdown, please contact the CONTEC sales representative or
sales office.
Use the product with the specified models by the CONTEC. Not doing so may cause fire
or malfunction.
Use the product in the specified operating condition (temperature and humidity)
CAUTION
Do not use or store the product in a location exposed to extremely high or low
temperature or susceptible to a rapid temperature change.
Example: - Exposure to direct sun - In the vicinity of a heat source
When unplugging the cable, hold the plug. Holding and pulling the cable itself can cause
a failure such as discontinuity.
The bundled AC power cable can only be used with the bundled AC adapter.
To clean the product, wipe it gently with soft cloth damp with either water or mild
detergent. Do not use chemicals or a volatile solvent, such as benzene and thinner, to
prevent peeling or discoloration of the paint.
When transporting the product, provide adequate measures to protect it from vibration
or shock.
No part of this document may be copied or reproduced in any form by any means
without prior written consent of CONTEC CO., LTD.
The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you
notice an omission or any questionable item in this document, please feel free to notify
CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors
that may appear in this document or for results obtained by the user as a result of using
this product.
Storage
When storing this product, keep it in its original packing form.
Wrap it in the packing material, and then put it in the box.
Store the package at room temperature at a place free from direct sunlight, moisture,
shock, vibration, magnetism, and static electricity.
Usage environment
It is expected that you will use this product in a comparatively good environment.
If you will use it in a harsh environment or if you require a long service life from it, we ask
that you separately prepare a power supply that fits your application.
If the AC adapter fails, CONTEC will replace it with an equivalent product (a charge may be
applied to the replacement).
Also, note that we cannot provide analyses of failure causes.
Disposal
When disposing of the product, follow the disposal procedures stipulated under the
relevant laws and municipal ordinances.
4. Using method
1. Make sure that the AC power cable is not plugged into a wall outlet.
2. Connect the AC power cable to the main body of AC adaptor connector (CN1).
3. Connect the DC cable of AC adaptor with the DC power supply connector.
4. Plug the AC power cable into a wall outlet.
This product has no power switch. When turning off, unplug the AC power cable from
the wall outlet.
5. Specifications
Item Specifications
Power suppl
y
space
Rated input volta
g
e 100VAC to 240VAC (continuous input), 50 to 60Hz
Permissible input volta
g
e 90VAC to 264VAC (continuous input), 50 to 60Hz
Input current 1.5A Max. (AC IN 100V)
Rated output volta
g
e +19VDC ±5%
Rated output current 3.42A (Max.)
Permissible momentar
y
blackout 5ms or less
Dielectric strength (between Input P
and S)
3.0kVAC for one minute
Insulation resistance (between P
and S)
Greater than 6.132GΩ (500VDC)
Environmental specs
Temperature Operatin
g
0 to 40°C
Non-operatin
g
- 20 to + 70°C
Humidity Operatin
g
20 to 80%RH (No condensation)
Non-operatin
g
10 to 90%RH (No condensation)
Floatin
g
dust particles Not to be excessive
Corrosive
g
ases None
Vibration resistance 10 to 60Hz / 0.5G
Noise re-
sistance
Line noise AC line / ±1kV
Static electricity
resistance
Contact discharge / ±4kV (IEC61000-4-2 Level 2)
Atmospheric discharge / ±4kV (IEC61000-4-2 Level
2)
Construction
Len
g
th of cable AC Power cable: 1.8m, DC cable: 1.2m
Input Plug Shape AC Code : IEC60320-C5
AC Inlet : IEC60320-C6
Physical dimensions (mm) 46.3 (W) x 108.3 (D) x 30 (H)
(not include pro
j
ection of cable)
Wei
g
ht Main bod
y
: 210
g
, AC power cable: 180
g
MTBF *1 100,000H (temperature 25°C)
Longevity *1 9,000H (temperature 25°C, 100VAC, with full load)
91,000H (temperature 25°C, 100VAC, with half
load)
*1 Estimates of MTBF and Longevity are not guaranteed but are for reference only.
6. Physical Dimensions
-
1
Contec PWA-65AWD9 is a switching AC adapter with a rated input voltage of 100-240VAC and a rated output voltage of +19VDC 3.42A. It has a permissible momentary blackout of 5ms or less and a dielectric strength of 3.0kVAC for one minute. The insulation resistance is greater than 6.132GΩ (500VDC). It can be used in environments with temperatures ranging from 0 to 40°C and humidity ranging from 20 to 80%RH (no condensation). It is resistant to vibration (10 to 60Hz / 0.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec ACAP19-01 Owner's manual
-
-
-
-
-
-
-
-
-