Livex Mini Pendant User manual

Type
User manual

Livex Mini Pendant: Illuminate your space with a touch of modern elegance. This stylish pendant light features a sleek design that complements various décor styles. With adjustable cord length, you can customize the hanging height to your preference. Installation is a breeze with clear instructions and all necessary hardware included. Enjoy warm, ambient lighting in your living room, bedroom, or dining area with Livex Mini Pendant.

Livex Mini Pendant: Illuminate your space with a touch of modern elegance. This stylish pendant light features a sleek design that complements various décor styles. With adjustable cord length, you can customize the hanging height to your preference. Installation is a breeze with clear instructions and all necessary hardware included. Enjoy warm, ambient lighting in your living room, bedroom, or dining area with Livex Mini Pendant.

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
MINI PENDANT
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old fixture and
all hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Be care not to lose any small parts necessary for installation.
3. Attach the crossbar to the Junction Box with the two junction box
screws as shown. The side of the cross bar marked "GND" must face
out. The junction box is not included.
4. By measuring, determine correct cord length needed for proper
hanging height, then lock it securely with small screw(C). NOTE:
slide cord clip to the proper position, then you may cut extra
cord.
5. While holding the lamp body towards the ceiling, connect the
electrical wires as Shown in Fig.2, making sure that all wire nuts are
secured. You may have to wrap the connections with electrical tape.
If your outlet has a ground wire (green or bare copper), connect the
fixture ground wire to it. Otherwise connect fixture’s ground wire
directly to the Mounting plate with the green screw provided. After
wires are connected, tuck them carefully inside the Junction Box.
6. Install canopy (A) onto the junction box, aligning screw hole on
crossbar with mounting holes in canopy and lock it securely with the
screws (B).
7. NOTE: THE SHADE(D) OF THE PRODUCT MAY VARY.
8. Install the light bulb(not included) in accordance with the fixture’s
specifications. NOTE: DO NOT EXCEED THE SPECIFIED
WATTAGE!!
Your installation is now complete. Return power to the junction
box and test the fixture.
Cord clip
(Shade may vary)
D
41221
41226
41244
41237
41240
4123141243
41222
41224
41245
41238
41225
41246
41239
40604
40618
40606
40630
40651
40605
40619
D
D
D
D
D
D
D
DD
WHITE
HOUSE
Black
WIRES
(Hot)
FIXTURE
WIRES
BLACK
WIRES
FIXTURE
Bare
FIXTURE
WIRES
(Ground)
HOUSE
(Neutral)
WIRES
White Green or
WIRES
HOUSE
Copper(Ground)
GREEN
Thread
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us online at: WWW.LIVEXLIGHTING.COM
©COPYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20211241240
FIG.2
FIG.1
  • Page 1 1

Livex Mini Pendant User manual

Type
User manual

Livex Mini Pendant: Illuminate your space with a touch of modern elegance. This stylish pendant light features a sleek design that complements various décor styles. With adjustable cord length, you can customize the hanging height to your preference. Installation is a breeze with clear instructions and all necessary hardware included. Enjoy warm, ambient lighting in your living room, bedroom, or dining area with Livex Mini Pendant.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI