2. Genexis
  3. Pulse EX600
Pulse EX600

Genexis Pulse EX600 Installation guide

  • Hello! I've reviewed the Pulse EX600 Installation Guide and I'm ready to assist you. This document provides detailed instructions on how to setup your Pulse EX600 as a router or extender, including both wired and wireless options. I can help you with placement, pairing, troubleshooting and answer questions about key features like its Wi-Fi EasyMesh support and more.
  • How can I install Pulse EX600 as a router?
    How can I install Pulse EX600 as a wireless extender?
    How can I install Pulse EX600 as a wired extender?
    How to switch the WiFi ON/OFF of the Pulse EX600?
EX
Pulse Series
Installation Guide
Wi-Fi EasyMeshTM suppoted
Box contents
• Genexis Pulse EX
• Power adapter
• Nework cable
• Labels (self-adhesive)
• Plugs & screws
Placement
Pulse EX suppots wo placement
options; desktop and mounted
to a wall. It is recommended to place
the device ‘away’ from objects.
Desktop
. Place the device horizontally on a
lat suface.
Wall mount
. Download and print the drilling
guide from htps:genexis.eu
productpulsedownloads
. Use the drilling guide to drill the
holes, inset plugs and put
screws into place.
Use the wall mount points on the back of the
Pulse EX to mount the device to the screws.
Various translations of this document (if available) and additional product
information can be foundon htps:genexis.euproductpulsedownloads
Installation guide
Pulse EX can be setup as a router or wirelesswired extender.
You're just a few steps away to install your device
via the Genexis EasyWiFi app
Installation with use of app
Scan QR-code
Download app and
follow the steps
Extender placement
For optimal peformance of the
Pulse EX as extender; place the
Pulse EX halfway in beween
your router and the problem area (as
shown below). Make sure placement
is within WiFi range of your router. If
the extender is placed too far away, it
cannot connect to the router.
Pulse EX
Router
Problem area, improved
by Pulse EX
Area that is good for
placing Pulse EX
Area covered by your
router
Installation of your Pulse device(s)
This installation guide is for installing
the Pulse EX as a router, as
explained on the right. In addition, an
extra Pulse EX can be installed as
a wireless or wired extender behind
the Pulse EX router.
If you already have a dierent router
(not a Pulse EX) and want to
install it as an extender, then look for
installation options: htps:genexis.
eupulse-installation-guide
Router
If you do not have a router installed,
stat installing your Pulse EX here:
. Place your Pulse EX near your
broadband outlet.
. Connect a nework cable beween
your broadband outlet and the
Pulse EX WAN pot (red pot).
. Plug the power adapter into an
electrical socket and connect it to
the power pot at the back of
the Pulse EX.
. Flip the ONOFF switch at the
back of the device to turn it on.
. Wait until the Status LED stops
blinking and turns solid green.
Your Pulse EX is now setup as a
router. Your nework is now ready to
be extended with a wireless or
wired extender, as explained on the
next pages.
Switching the WiFi ONOFF
The WiFi function of the Pulse EX
can be switched ON or OFF by
means of the Mode buton.
• Switch OFF: On the Pulse EX,
press and hold the Mode buton until
the Status LED turns solid yellow.
• Switch ON: On the Pulse EX,
press and hold the Mode buton until
the Status LED stats blinking green
or turns solid green.
Connecting to the wireless nework
You can connect your personal
device (e.g., mobile phone) to the
Pulse EX via manual pairing. If
automated pairing is prefered, please
check for your speciic device how
this can be initiated. Before pairing,
make sure the Status LED is solid
green. If not, switch the WiFi ON as
described in this installation guide.
Manual pairing
The WiFi nework name and WiFi key
are printed on the labels of the
Pulse EX router.
. Peform a search of available
wireless neworks on your personal
device or scan the QR-code on the
label on the botom of the
Pulse EX.
. Select the WiFi nework name
printed on the label on the botom
of the Pulse EX.
. Enter the WiFi key printed on the
label of the Pulse EX.
Follow the instructions of the router
in case the Pulse EX is in
extender mode.
Wireless extender
. Place the additional Pulse EX
as described on the let.
. Plug the power adapter into an
electrical socket and connect it to
the power pot at the back of
the Pulse EX.
. Flip the ONOFF switch at the
back of the device to turn it on.
. Wait until the Status LED
surrounding the Mode buton
stats blinking green.
. On the Pulse EX, press and
release the Mode buton once. The
status LED will stat blinking blue.
. Press the same Mode buton on
the Pulse EX router within
wo minutes.
. Automated pairing is now stated.
. The Status LED turns solid blue
indicating that pairing of the Pulse
EX extender with the router
is successful (the Pulse EX will
automatically reboot ater the
automated pairing; this may take
up to several minutes).
. Wait until the Status LED stops
blinking and turns solid green.
Your Pulse EX is now setup as a
wireless extender.
Wired extender
. Connect a nework cable beween
the LAN pot (yellow connector)
of the Pulse EX router and the
WAN pot (red connector) of the
Pulse EX extender.
. Plug the power adapter into an
electrical socket and connect it to
the power pot at the back of the
Pulse EX extender.
. Flip the ONOFF switch at the
back of the device to turn it on.
. Wait until the Status LED stops
blinking and turns solid green
(the Pulse EX extender will
automatically reboot during the
setup; this may take up to
several minutes).
Your Pulse EX is now setup as a
wired extender.
LED & buton oveview
Status
Green – system is operational ready
Green (blinking) – connectiviy lost
Yellow – system statup or WiFi OFF
Yellow (blinking) – system is not ready
Blue – automated pairing (WPS) successful
Blue (blinking) – automated pairing (WPS) in progress
Red – system  booting failure
O – power o
Mode buton
Pairing (WPS) – press and release once
WiFi ON – press and hold until Status LED turns green
(blinking or solid)
WiFi OFF – press and hold until Status LED turns solid
yellow
Changing your nework setings
You can access the Pulse EX
web inteface (GUI) to change your
nework setings. The Pulse EX
must be in router mode to access
the GUI.
. Use a web browser on your
personal device and navigate to
the GUI URL as printed on the label
on the botom of the Pulse EX
. Login using the credentials as
printed on the labels on the
botom of the Pulse EX.
Power saving options
Power saving options are available via
the web inteface.
Pot oveview
Power pot
ONOFF
switch
LAN pots Reset
buton
WAN pot
USB .
pot
ONOFF switch
Switch ON – lip the switch to ON
Switch OFF – lip the switch to OFF
Reset buton (recessed)
Reboot – press and release once
Factoy reset – press and hold until the
Status LED stats fast blinking green
Troubleshooting
Is the Status LED solid red?
Contact your sevice provider.
Is the Status LED solid yellow?
The WiFi of the Pulse EX is turned
OFF. Please turn the WiFi ON as
described in this installation guide.
Is the Status LED not solid blue ater
automated pairing (WPS)?
Automated pairing (WPS) beween
the Pulse EX and Genexis router
or personal device failed. Please follow
the instructions again to setup the
Pulse EX as a wireless extender
or connecting your personal device
to the wireless nework. It might be
helpful to move the Pulse EX
closer to your Genexis router.
Is the Status LED blinking green for
 minutes?
• Router: Pulse EX does not have
a connection with the broadband
nework. Please verify your wired
connection with the broadband
outlet or contact your
sevice provider.
• Wirelesswired extender:
Connection beween the Genexis
router and the Pulse EX is
not stable. Please check the cable
connection with the Genexis router
or move the Pulse EX closer to
the Genexis router.
Is the Status LED blinking yellow?
The Pulse EX is being upgraded
with new soware. Please wait until
the Status LED turns solid green
again.
Return the Pulse EX to factoy
default setings
With the reset buton you can reset
the Pulse EX to its factoy default
setings. You can press this buton
with a small pin or paperclip.
. Press and hold the reset buton
until the Status LED stats fast
blinking green.
. Wait until the Status LED turns
solid green again.
Your Pulse EX is now setup as
a router again with the setings as
printed on the label of
the Pulse EX.
Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat a
 AC Eindhoven
The Netherlands
Name and title of authorized person
Maaten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven --
The Netherlands
Hereby, Genexis Netherlands B.V. declares that the product Pulse EX is in
compliance with Directives EU, EC, EU and
Delegated directive .
The full text of the EU declaration of conformiy is available at the following
internet address: htps:genexis.euproductpulseredpulse-ex
EU Declaration of Conformiy
Frequency bands and maximum radio frequency power transmited
The Pulse EX operates in the frequency bands of , Ghz and Ghz.
The maximum radio frequency power transmited in these bands is:
•  dBm( mW) (EIRP)for the  MHz – . MHz band
•  dBm ( mW) (EIRP)for the  MHz –  MHz band *
•  dBm ( mW) (EIRP) for the  MHz –  MHz band
* In EU,  –  MHz is restricted to indoor.
Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves
the right to change, modify, transfer, or othewise revise this publication without notice.
Revision . September , Copyright ©  Genexis Netherlands B.V. All rights reseved.
/