LIGHT MY BRICKS 21338 Installation guide

Category
Power banks
Type
Installation guide

LIGHT MY BRICKS 21338 offers a comprehensive lighting solution for Lego enthusiasts, enabling them to illuminate their A-Frame Cabin model with various LED light components. The kit includes an array of bit lights in different colors and sizes, allowing for customization and highlighting specific features of the cabin. Expansion boards facilitate the connection of multiple lights, while the micro expansion board enables the use of micro bit lights for intricate detailing.

LIGHT MY BRICKS 21338 offers a comprehensive lighting solution for Lego enthusiasts, enabling them to illuminate their A-Frame Cabin model with various LED light components. The kit includes an array of bit lights in different colors and sizes, allowing for customization and highlighting specific features of the cabin. Expansion boards facilitate the connection of multiple lights, while the micro expansion board enables the use of micro bit lights for intricate detailing.

LEGO® AFRAME CABIN #21338
LIGHT KIT
INSTALLATION GUIDE
2
Light My Bricks
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
LEGO® AFRAME CABIN 21338
INSTALLATION GUIDE
Hi There!
We’re here to help you get started on the LEGO®
A-Frame Cabin 21338 Light Kit.
This PDF details the instructions for the LED light kit only.
If you run into any issues, please refer to the
troubleshooting section towards the end of this guide.
Have fun and enjoy!
INSTALLATION GUIDE
PACKAGE CONTENTS 3
PACKAGE CONTENTS:
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
8 x White 15cm Bit Light
7 x Yellow 15cm Bit Light
2 x White 30cm Bit Light *
2 x Yellow 30cm Bit Light *
2 x Cool White 30cm Bit Light
1 x Orange 30cm Large Bit Light
4 x 6-Port Expansion Board
2 x 8-Port Expansion Board
1 x Flicker Eects Board
14 x Adhesive Square
4 x Round Plate 1x1 - Trans Yellow
2 x Round Plate 1x1 w/ Open Stud - White
5 x Round Plate 1x1 w/ Open Stud - Black
2 x Tile 1x1 - Black
4 x Plate 1x1 Mod Rounded w Handle - Black
2 x Arm Skeleton, Bent with Clips (Horizontal Grip) - Black
1 x 5cm Connecting Cable
2 x 15cm Connecting Cable
3 x 50cm Connecting Cable
* Indicates components which include spares
Mixed Components 1Individual Bags
Mixed Components 2
Connecting Cables
USB Power Cable
1x USB Power Cable
(Power Source not Included)
CONTENTS 4
Contents
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
Before You Begin 5
Blueprint 10
Instructions 11
Final Product 53
Troubleshooting 54
Contact 58
BEFORE YOU BEGIN 5
Before You Begin
Laying cables in between
and underneath bricks
Cables can fit in between and underneath
LEGO® bricks, plates, and tiles providing
they are laid correctly between the LEGO®
studs. Do NOT forcefully join LEGO®
together around cables; instead ensure
they are laying comfortably in between
each stud.
CAUTION: Forcing LEGO® to connect over
a cable can result in damaging the cable
and light.
Connecting Cable
Connectors To Expansion
Boards
Take extra care when inserting connectors
to ports of Expansion Boards. Connectors
can be inserted only one way. With the
expansion board facing up, look for the
soldered “=” symbol on the left side of the
port. The connector side with the wires
exposed should be facing toward the
soldered “=” symbol as you insert into the
port. If a plug won’t fit easily into a port
connector, do not force it.
Incorrectly inserting the connector can re-
sult in bent pins inside the port or possible
overheating of the expansion board when
connected.
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 6
Before You Begin
Connecting Cable
Connectors To Strip Lights
Take extra care when inserting connectors
to ports on the Strip Lights. Connectors
can be inserted only one way. With the
Strip Light facing up, ensure the side of
the connector with the wires exposed is
facing down. If a plug won’t fit easily into
a port connector, don’t force it. Doing so
will damage the plug and the connector.
Connecting Micro Cable
Connectors To Micro
Expansion Board Ports
Take extra care when inserting the
micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit
Lights to Micro Expansion Boards is similar
to connecting lights and cables to Strip
Lights. With the expansion board facing
up, ensure the side of the connector with
the wires exposed is facing down. If a plug
won’t fit easily into a port connector, do
not force it. Use your fingernail to push the
plastic part of the connector to the micro
port.
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 7
Before You Begin
Installing Bit Lights Under
Lego® Bricks And Plates
When installing Bit Lights under LEGO®
pieces, ensure they are placed the correct
way up (Yellow LED component exposed).
You can either place them directly on top of
LEGO® studs or in between.
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 8
Before You Begin
Disconnect
Used when you need to
remove a LEGO piece/ section
or LMB component.
Twist/ Braid
Seen when a set of cables
need to be grouped and
twisted together.
Directional
Used to show where to route
cables, place components, or
move them.
Power On Test
Found at the end of a major
step to test the lights. Will be
located in the top left corner.
Bend/Pivot
Used when a component
needs to be bent, or part
folded or pivoted.
Note
Notes will be found alongside
the instruction photos and
explain what to do.
Connect
Used when you need to
connect a LEGO piece or LMB
component.
Turn/ Flip
Will be found in the top left
corner when the set needs to
be rotated or flipped.
Light Kit Component
This is the most important image
format as it indicates which part
to use from the Light Kit. Make
sure you pay close attention to
which part is shown.
The Symbols Used In This Guide
When going through the following guide you will
come across symbols and formats that will assist
with the installation of your light kit. Take notice of
them as each has a specific purpose.
White 30cm Bit Light
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
BEFORE YOU BEGIN 9
Before You Begin
Disconnect Note
The red coloured note is
used when the topic focuses
on a component being
disconnected or like here, the
removed pieces.
Connect Note
The green coloured note is
used when the topic focuses
on a component being
connected, like the shown
Power Bank.
General Note
This is a sample note that is
used anywhere in this guide. It
will explain a dicult section
where photos are hard to
illustrate or easily confused.
NOTE
Connect to a 5V USB Power Bank,
5V USB Wall Adaptor, or USB to AA
Battery Pack (sold separately)
NOTE
You should have these parts left
over that were removed from the
LEGO set
NOTE
Take the 5cm Connecting Cable
from the 4-Port Micro Expansion
Board and route it into the “IN”
port of the Flicker Eects Board
x2
Connect Focus
Used to highlight a hard to
see area where a component
is being connected.
Disconnect Focus
Used to highlight a hard to
see area where a component
is being disconnected.
General Focus
Used to highlight a hard to
see area where a component
needs to be acted on.
Repeat Step
Repeat the previous step eg.
Make a spotlight, then make a
second spotlight.
Removed Pieces
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
BLUEPRINT 10
BLUEPRINT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
INSTRUCTIONS 11
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
INSINSTRTRCUUCSTIONTIONS
TTo ensuro ensuroe a smoe a smootth insth instoallation allation off
yyrouour lighlightt kit kitr, please , please rfead and ead and foollolloww
each steach stcep ep craareelfulfullyy. I. Iff y ynou run iou run inttoo
ananry issues, please y issues, please reeffreer tteo the onlino the online
trtrooubleshooubleshooeting guidting guide..
Wenn Sie Probleme mit Ihrem Light My Bricks-Set haben, sehen Sie sich unser Video zur Fehlerbehebung an oder
lesen Sie die Auflistung der häufigsten Ursachen, die Ihnen bei der Fehlersuche helfen hier.
Si vous rencontrez des problèmes avec votre kit Light My Bricks, regardez notre vidéo de dépannage ou consultez la
liste des causes les plus fréquentes pour vous aider à les résoudre ici.
Se si verificano problemi con il set Light My Bricks, guardare il nostro video per la risoluzione dei problemi o leggere
l'elenco delle cause più comuni per la risoluzione dei problemi qui.
INSTRUCTIONS 12
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
1
INSTRUCTIONS 13
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
2
White 30cm Bit Light
Round Plate 1x1 - Trans Yellow
INSTRUCTIONS 14
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
3
6-Port Expansion Board
USB Power Cable
3 x 50cm Connecting Cable
2x Adhesive Square
INSTRUCTIONS 15
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
4
NOTE
Thread one of the 50cm
Connecting Cables as shown
INSTRUCTIONS 16
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
5
INSTRUCTIONS 17
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
6
8-Port Expansion Board
INSTRUCTIONS 18
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
7
Yellow 30cm Bit Light
NOTE
If you have trouble connecting
the Bit Light under the LEGO
piece, lightly twist and push the
piece in until it stays.
INSTRUCTIONS 19
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
8 9
INSTRUCTIONS 20
DIRECTIONAL
CONNECT
DISCONNECT TURN / FLIP NOTE ICON
POWER ON TEST
TWIST / BRAIDBEND / PIVOT
LEGO® A-FRAME CABIN 21338 LIGHT KIT INSTALL GUIDE
10
White 15cm Bit Light
Round Plate 1x1 - Trans Yellow Yellow 15cm Bit Light
Tile 1x1 - Black
Round Plate 1x1 - Trans Clear
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59

LIGHT MY BRICKS 21338 Installation guide

Category
Power banks
Type
Installation guide

LIGHT MY BRICKS 21338 offers a comprehensive lighting solution for Lego enthusiasts, enabling them to illuminate their A-Frame Cabin model with various LED light components. The kit includes an array of bit lights in different colors and sizes, allowing for customization and highlighting specific features of the cabin. Expansion boards facilitate the connection of multiple lights, while the micro expansion board enables the use of micro bit lights for intricate detailing.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI