Esco 10497 User manual

Equipment Supply Company

Instruction Manual

3 Ton Jack Stands - High Performance Style

MODEL 10497

MODEL 10498

MODEL 10499

01.06.2022 V.1

Read this manual and follow All Safety Rules and Operating Instructions before ANY use of this product.

21.800.352.9852 • [email protected] •www.esco.net

3 Ton Jack Stand “High Performance Style” - MODEL #10497, 10498, 10499

CAUTION:

READ AND FOLLOW ALL WARNINGS, CAUTIONS AND INSTRUCTIONS ASSOCIATED WITH

THE PROPER USE OF THIS PRODUCT, FAILURE TO COMPLY COULD RESULT IN DEATH,

BODILY INJURY AND/OR DAMAGE TO EQUIPMENT.

Specications

Model Capacity (Per Pair)* Min. Height Max. Height Base Size

10497 3 Ton

6,000 lbs.

13.2 in

335mm

21.5 in

546mm

12 in x12 in

305mm

10498 3 Ton

6,000 lbs.

13.2 in

335mm

21.5 in

546mm

12 in x12 in

305mm

10499 3 Ton

6,000 lbs.

11 in

280mm

17 in

432mm

9.5 in x 9.5 in

241mm

*Use stands only as identical pair. Weight-rating capacities apply to applications using matching stands.

Important Safety Information

Read these safety warnings before operation.

NOTE: The manufacturer is not responsible in any way for any damage that may

result to persons or objects due to improper use of these Jack Stands.

WARNING!

Study, understand, and follow all instructions before operating this device. Failure to heed these

warnings may result in loss of load, damage to jack stands, and / or jack stand failure resulting in

personal Injury or property damage. No alternations shall be made to this product.

WARNING!

Do not overload jack stands beyond rated capacity. Overloading can cause damage to or failure

of the jack stands and bodily harm. Position load on center of saddle only. Use stands to support

one end of vehicle. Always use stands on hard level surface capable of sustaining the load. Use

of stands on anything other than a hard level surface can result in stand instability and possible

loss of load. Use a minimum of four stands to support and stabilize a vehicle, and minimum of two

additional stands for each additional axle assembly. Do not enter the vehicle or start the engine

while the vehicle is supported on stands.

3 Ton Jack Stand “High Performance Style” - MODEL #10497, 10498, 10499

3

1.800.352.9852 • [email protected] •www.esco.net

Maintenance & Inspection

1. Visual Inspection shall be made before each use of the stands, checking for cracks, cracked

welds and missing and / or damaged parts. Any stand that appears to be damaged in any way

should be removed from service immediately. If in doubt call ESCO - Equipment Supply Co. at

1-800-352-9852.

2. Because of the potential hazards associated with the misuse of equipment of this type, no

modications should be made of the product without consent from manufacturer.

Operation

ALWAYS chock the wheel(s) opposite where you are lifting. Use recommended (2) wheel chocks in

front and behind the wheel(s) to keep vehicle from shifting forward/backward.

• Refer to your vehicle owner’s manual for proper jacking procedures. Lift only on areas of the

vehicle specied by the vehicle manufacturer.

NOTE: If only supporting one corner of the vehicle, place jack stand under the

manufacturers recommended jacking point and adjust the height and lock in with the

pin/linchpin.

SUPPORTING FRONT/REAR END:

If supporting the front or rear end of a vehicle, ALWAYS use jack stands in an identical pair locked

and at the same height. DO NOT use any other materials such as wood, steel, etc. to gain extra

height when supporting vehicle.

LIFTING ENTIRE VEHICLE:

If lifting the entire vehicle, support the front end rst. Then, using a matching pair locked and set to

the same height, lift the back end of the vehicle.

•Position stands under vehicle at points specied by the vehicle manufacturer as proper load

support points.

ALWAYS inspect the vehicle load and jack stands to make sure that the jack stand(s) is/are

positioned at on the ground on all three sides and the vehicle DOES NOT shake or tilt while

supported.

WARNING: It is recommended when lifting front end or back end of vehicle to use a

pair of matching jack stands. Jack stands are NOT to be used as a permanent lifting/

stability solution and are ONLY to be used during the repair of vehicle. DO NOT leave

vehicle on jack stand(s) for an extended period. This may lead to damage to jack

stand(s), vehicle, and/or worse possible harm/death.

41.800.352.9852 • [email protected] •www.esco.net

3 Ton Jack Stand “High Performance Style” - MODEL #10497, 10498, 10499

Operation (Cont.)

• To adjust stands:

1. Remove Linchpin and chained pin and adjust to the desired height.

2. Place chained pin into hole location and attach the Linchpin and lock pin in.

3. Carefully lower load onto stands.

NOTE: Only attachments and/or adapters supplied by the manufacturer shall be used with these

jack stands. please consult with manufacturer for approved accessories for these jack stands.

MODEL 10497

Provided Linchpin to

Secure Post to Base using

chained pin.

Flat Removable Rubber Top. Cir-

cular For Maximum Stability.

MODEL 10498 & 10499

Three (3) Leg Circular

Base. Ensure even

weight distribution.

LINCHPIN:

Proper Connection of the

Linchpin to the chained pin as

seen above. Please make sure

when receiving this product all

parts are included.

3 Ton Jack Stand “High Performance Style” - MODEL #10497, 10498, 10499

5

1.800.352.9852 • [email protected] •www.esco.net

NOTES:

____________________________________________________________________________________________________________

___________________________________________________________________________________________________________

____________________________________________________________________________________________________________

Equipment Supply Company

01.06.2022 V.1

CONTACT INFO:

www.esco.net - [email protected]

15270 Flight Path Drive

Brooksville, FL 34604

PH. 352.754.1117

Toll Free. 1.800.352.9852 (US, Canada Only) Fax: 352.754.4508

WARNING: Cancer and Reproductive Harm- www.P65Warnings.ca.gov

Stay Connected with ESCO....

Esco 10497 User manual

Esco 10497 User manual

Related papers

Other documents