Allen + Roth MIR3032 Installation guide

Brand: Allen + Roth

Model: MIR3032

Type: Installation guide

This manual is also suitable for

MIR(S)3032

ITEM #0970869

MODEL #MIR3032

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-527-1292, 8:30 a.m. - 5 p.m., Monday - Friday, CST

ATTACH YOUR RECEIPT HERE

Purchase Date

LED LIGHTED MIRROR

E465631

Français p. 9

Español p. 17

A Fixture 1

B Mounting Plate 1

PART DESCRIPTION QUANTITY

HARDWARE CONTENTS (shown actual size)

PACKAGE CONTENTS

READ AND SAVE THESE INSTRUCTIONS.

SAFETY INFORMATION

DANGER

C Adhesive 4

(preassembled to sheet (D))

Wire

Connector

Qty. 3

Machine

Screw

Qty. 2

Fixture

Screw

Qty. 4

Plastic

Anchor

Qty. 4

D Sheet 1

(preassembled to fixture (A))

E Plastic Washer 1

(preassembled to mounting plate (B))

• For your protection and safety, carefully read and understand the information provided in this

manual completely before attempting to assemble, install or operate this product. Failure to do so

could lead to fire, electrical shock or other injuries that could be hazardous or even fatal.

• DO NOT connect this fixture to an electrical system that does not provide a means for equipment

grounding. Never use a fixture in a two-wire system that is not grounded. Installing a fixture into an

electrical system not having a proper grounding means could cause metal parts of the fixture to

carry electrical currents if any of the fixture wires, wire connections or splices were to become

broken, cut or loose during the mounting or normal operation of the fixture. Under this condition,

anyone coming in contact with the fixture would be subject to electrical shock, which could cause

serious injury or death.

SAFETY INFORMATION

• DO NOT connect the bare or green insulation fixture ground wire to the black (HOT)

current-carrying wire or the white (NEUTRAL) house wire. Connection of the bare or green fixture

ground wire to the black or white house wires may cause metal parts of the fixture to carry electrical

currents. Under this condition anyone coming in contact with the fixture will receive electrical shock,

which could cause serious injury or death.

• DO NOT damage or cut the wire insulation (covering) during installation of fixture. DO NOT permit

wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation,

which could cause serious injury or death from electrical shock.

• All electrical connections must be in agreement with local codes and ordinances, the National

Electric Code (NEC) and ANSI/NFPA 70-1999. Contact your municipal building department to learn

about your local codes, permits and/or inspections. Risk of fire - most dwellings built before 1985

have supply wire rated for 140°F. Consult a qualified electrician before installation.

• To avoid personal injury, the use of gloves may be necessary while handling fixture parts with sharp

edges.

• DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to an

outlet box or to a mounting plate which is first attached to the outlet box. Wire connectors will not

support the weight of a fixture. Suspending a fixture by the house wires and wire connectors will

result in the fixture falling, with the possibility of personal injury and the danger of electrical shock or

fire.

• To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this light

fixture are designed to accept only one 12-gauge house wire and two lead wires from the light

fixture. If your house wire is larger than 12-gauge or there is more than one house wire to connect to

the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.

• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help.

WARNING

CAUTION

• TURN OFF ELECTRICITY at main fuse box (or circuit breaker box) before beginning installation by

removing the fuse (or switching the circuit breaker off).

• If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture.

Contact a qualified, licensed electrician for information regarding the proper grounding methods as

required by the local electrical code in your area.

PREPARATION

ASSEMBLY INSTRUCTIONS

• All fixtures must be mounted to an outlet box that is supported by the building structure.

• Do NOT tamper with or attempt to repair LED component of fixture. The light source is designed for

this specific application and should not be serviced by untrained personnel. If any servicing is

required, call our customer service department.

• Total wattage for this fixture is 24 watts; do not attempt to replace the LEDs.

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble

the product.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Flathead Screwdriver, Phillips Screwdriver, Wire Strippers,

Drill, 1/8 in. Drill Bit, Hammer, Pencil, Pliers, Wire Cutters, Safety Glasses, Stepladder, Electrical Tape

Helpful Tools (not included): Soft Cloth, Level

OFF

Turn off circuit breakers and wall switch to

the fixture supply line leads.

DANGER: Failure to disconnect power

supply prior to installation may result in

serious injury or death.

Remove existing fixture and disconnect all

electrical wiring.

SAFETY INFORMATION

CAUTION

ASSEMBLY INSTRUCTIONS

Remove sheet (D) from fixture (A). Determine

the approximate location for the fixture (A).

Place sheet (D) against the wall using the

adhesive (C), and mark the location of the holes

using a pencil or a marker (not included).

Then, using a 1/8 in. drill bit (not included), drill four

pilot holes at the marked locations.

Position plastic anchor (DD) in each pilot hole. Gently

tap plastic anchors (DD) with a hammer (not

included) until flush with wall surface. Screw fixture

screw (CC) into plastic anchor (DD) about 1/3 of the

way, allowing about 1 in. of the screw to remain

showing.

CAUTION: To mount to wall without an outlet

box, proper wiring for a light fixture must be present

and/or accessible. If not, consult a qualified

electrician before installing the fixture.

Hardware Used

Plastic Anchor

x 4

Fixture Screw

Pilot Hole

Outlet Box

ASSEMBLY INSTRUCTIONS

Thread wires through mounting plate (B) and plastic

washer (E). Prepare wires by stripping 3/4 in. of

insulation from wire ends using wire strippers (not

included). Connect WHITE wire from fixture (A) to

WHITE wire from outlet box using existing wire

connector or wire connector (AA). Connect BLACK

wire from fixture (A) to BLACK wire from outlet box

using existing wire connector or wire connector (AA).

Connect BARE/GREEN ground wire from outlet box

to BARE ground wire from fixture (A) with wire

connector (AA).

NOTE: Screw wire connectors (AA) on in a

clockwise direction.

WARNING: Never connect ground wire to

WHITE or BLACK power supply wires.

WARNING: To reduce the risk of fire, electrical

shock or personal injury, wire connectors (AA) are

designed to accept only one 12-gauge house wire

and two lead wires from the light fixture. If your house

wire is larger than 12-gauge or there is more than one

house wire to connect to the corresponding fixture

lead wires, consult an electrician for the proper size

wire connectors to use.

Hardware Used

Wire Connector

x 3

Wrap electrical tape (not included) around

each individual wire connector (AA) down

to the wire. Push wire connectors (AA)

gently back into outlet box. Carefully push

excess wiring into outlet box.

WARNING: Make sure no bare wire or

wire strands are visible after making

connections.

Outlet Box

Attach mounting plate (B) to outlet box

(not included) using existing washers and

outlet box screws or the machine screws

(BB). NOTE: If the outlet box screws

required for your outlet box are of a different

size than the machine screws (BB), consult

a licensed electrician before proceeding.

Tighten machine screws (BB) to secure

mounting plate (B). Push plastic washer (E)

into mounting plate (B).

CAUTION: Make sure the outlet box

can support 35 lbs. hanging weight. Use

metal outlet box; plastic outlet boxes are not

recommended.

Hardware Used

Machine Screw

x 2

ASSEMBLY INSTRUCTIONS

Hang fixture (A) using the slots on the back of

fixture (A).

Slot

WARRANTY

Printed In China

JMLI1801

The distributor warrants all of its lighting fixtures against defects in materials and workmanship for five (5)

years from the date of purchase. If within this period the product is found to be defective, take a copy of

the bill of sale as a proof of purchase and the product in its original carton to the place of purchase. The

distributor will, at its option, repair, replace or refund the purchase price to the consumer. All costs of

installation and removal of the fixture is the responsibility of the consumer. This warranty does not cover

fixtures becoming defective due to misuse, accidental damage or improper handling and/or installation and

specifically excludes liability for direct, incidental or consequential damages. As some states do not allow

exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This

warranty gives you specific rights and you may also have other rights which may vary from state to state.

TROUBLESHOOTING

WARNING: Before beginning work, shut off the power supply to avoid electrical shock.

CARE AND MAINTENANCE

• Wipe fixture with soft, damp cloth. Do not use an abrasive cleaner on fixture.

OPERATING INSTRUCTIONS

Touch

Sensor

Tapping the touch sensor on fixture (A) turns light ON

and OFF.

Light does not come on

initially or no longer

comes on.

Fuse blows out or

circuit breaker trips.

1. Power is OFF.

2. Faulty connection.

3. LED component is not working

properly.

1. Crossed wires.

2. Power wire is grounding out.

1. Check wiring.

2. Check all connections.

1. Make sure power supply is ON.

2. Check wiring and all connections.

3. Contact Customer Service.

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Allen + Roth MIR3032 Installation guide

Brand: Allen + Roth

Model: MIR3032

Type: Installation guide

This manual is also suitable for

MIR(S)3032

Download PDF

report

Allen + Roth MIR3032 Installation guide

This manual is also suitable for

Allen + Roth MIR3032 Installation guide

Related papers

Other documents