Draw-Tite 75507† Installation guide

Type
Installation guide

This manual is also suitable for

Draw-Tite 75507† is a weight-distributing hitch specifically designed for Mazda MPV models manufactured between 2004 and the present. It enables the vehicle to tow trailers with a maximum gross weight of 5,000 lbs and a maximum tongue weight of 500 lbs. Its key features include:

*Compatibility with both models with and without ground effects. *Easy installation with provided hardware and detailed instructions. *Durable construction with high-strength steel components. *Contoured design to fit the vehicle's frame and fascia without compromising ground clearance. *Provision for weight distribution to enhance stability and handling while towing.

Draw-Tite 75507† is a weight-distributing hitch specifically designed for Mazda MPV models manufactured between 2004 and the present. It enables the vehicle to tow trailers with a maximum gross weight of 5,000 lbs and a maximum tongue weight of 500 lbs. Its key features include:

*Compatibility with both models with and without ground effects. *Easy installation with provided hardware and detailed instructions. *Durable construction with high-strength steel components. *Contoured design to fit the vehicle's frame and fascia without compromising ground clearance. *Provision for weight distribution to enhance stability and handling while towing.

Installation Instructions
Mazda MPV
(Models with Ground Effects,
Models without Ground Effects 2004 to Present)
Part Numbers:
87420
75507
44553
Hitch Shown In Proper Position
Equipment Required:
Wrenches: 3/4, 7/8, 17mm
Drill Bits: None
1. Loosen two rearmost muffler hangers.
2. Raise hitch into position.
3. Push muffler out of the way and install fasteners as shown above.
4. Reinstall muffler hangers.
Tighten all 1/2 GR5 fasteners with torque wrench to 75 lb-ft (102 N-m).
Rev. A06-06-0675507NSheet 1 of 3
z 2006 Cequent Towing Products
Hex Nut, 1/2-13Qty. (1)
8
Hex Bolt, M10 x 1.25 x 40mmQty. (2)
4
Spacer, 2 x 2 x 1/4”Qty. (1)
7
Handle Nut, 1/2”Qty. (2)
3
Carriage Bolt, 1/2-13 x 1-3/4”Qty. (1)
6
Conical Washer, 1/2”Qty. (3)
2
Conical Washer, 3/8”Qty. (2)
5
Hex Bolt, 1/2-13 x 1-3/4”Qty. (2)
1
Tighten all M10 CL8.8 fasteners with torque wrench to 38 lb.-ft (52 N-m).
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Fastener Kit: 75507F
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
350 lb (159 kg)3500 lb (1589 kg)
Weight Carrying
Ball Mount
500 lb (227 kg)5000 lb (2270 kg)
Weight Distributing
Max Tongue
WT
Max Gross
Trailer WT
Hitch type
Wiring Access Location: SUV1, SUV2
Frame Rail
Fascia
Frame Rail
Existing Weld Nut
Tow Hook
  • Page 1 1
  • Page 2 2
  • Page 3 3

Draw-Tite 75507† Installation guide

Type
Installation guide
This manual is also suitable for

Draw-Tite 75507† is a weight-distributing hitch specifically designed for Mazda MPV models manufactured between 2004 and the present. It enables the vehicle to tow trailers with a maximum gross weight of 5,000 lbs and a maximum tongue weight of 500 lbs. Its key features include:

*Compatibility with both models with and without ground effects. *Easy installation with provided hardware and detailed instructions. *Durable construction with high-strength steel components. *Contoured design to fit the vehicle's frame and fascia without compromising ground clearance. *Provision for weight distribution to enhance stability and handling while towing.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI