Troy-Bilt 31AM6CP4711 Operating instructions

Troy-Bilt
Brand
Troy-Bilt
Model
31AM6CP4711
Type
Operating instructions

This manual is also suitable for

Chute Control
Head
778 -13548© 2016 31AM6CP4
B
A
Insert chute control rod into the support
bracket on rear of the dash panel.
Finish securing chute control head
to chute support bracket with
wing nut and hex screw removed
in Step 2.
B. Insert chute
control rod into
rear of chute
control head.
Secure chute
control rod to
chute control
assembly with
hairpin clip
removed in
Step A.
A. Remove
hairpin clip
from rear of
chute control
head.
Upper Handle
Chute
Control Rod
Overhead
Chute Control
Chute
Chute Base
Chute Support
Bracket
Shift Lever
Two-Way Chute
Control
A. Remove wing nut and hex
screw from chute control head and
clevis pin and cotter pin from chute
support bracket.
B. Position
chute
assembly
(forward-
facing)
over
chute
base.
B
A. Place
chute
assembly
onto
chute
base.
B. Secure
chute
control
head to
chute support bracket with clevis pin and
cotter pin removed in Step 2.
B
C
A. Loosen the top two lock nuts securing the upper
and lower handle and remove the two carriage
screws from the lower handle and set aside.
B. Place shift lever
into F6 position.
C. Pivot upper handle
into operating
position.
D. Attach the two
carriage screws
and lock nuts
removed in Step
1. Finish securing
the handle by
tightening the top two lock
nuts loosened in Step 1.
D
A
A
A
B
B
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
Fill fuel tank with clean,
fresh gasoline. Do not fill
above the base of fuel
tank neck.
Check the oil level using
the dipstick. Add oil if
necessary. (Refer to the
Operator’s Manual)
778 -13548© 2016 31AM6CP4
Throttle
Control
Electric Starter
Outlet
Electric Starter
Button
Oil Fill /
Dipstick
Primer
Key
Choke
Control
Gas Fill
A. Connect an
extension cord
to the electric
starter outlet.
B. Plug the other
end of the cord
into a three-
prong 120-volt,
grounded, AC
receptacle.
Push primer
three times.
A. To start engine,
push the starter
button.
B. When engine
starts, slowly move
choke control
into the Run
position.
C. Disconnect cord
from power
receptacle first and
then from snow
thrower’s outlet.
Move throttle control into
the Fast position.
Move the choke control
into the Choke
position.
Insert the key
into the key
switch until
the key snaps
into place.
Do not turn
the key!
7
10
8
11
9
12
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
  • Page 1 1
  • Page 2 2

Troy-Bilt 31AM6CP4711 Operating instructions

Troy-Bilt
Brand
Troy-Bilt
Model
31AM6CP4711
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents