Halsey Taylor HTBPFP OLD MTG Owner's manual

Brand: Halsey Taylor

Model: HTBPFP OLD MTG

Type: Owner's manual

The Halsey Taylor HTBPFP OLD MTG is a frost-resistant fountain designed for indoor use on a heated wall. It features a push-button activation, a vandal-resistant bubbler, and a self-closing valve. The fountain is easy to install and maintain, with a durable construction that ensures long-lasting performance. The HTBPFP OLD MTG is ideal for use in schools, offices, and other public places where reliable access to fresh, clean drinking water is essential.

Halsey Taylor Owners Manual

Models: HT-EBP-FR HT-SEBP-FR

Frost Resistant Fountains

Installer

To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE INSTRUC-

TIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLI-

ANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES. After installation,

leave these instructions inside the fountain for future reference. This Freeze Resistant Fountain is

shipped in two separate cartons. The second carton contains the Freeze Resistant Package that

is installed on an interior heated wall. Refer to the Freeze Resistant Package for the rough-in

dimensions for installation.

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES IS

A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE

BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN ELEC-

TROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER. THIS

CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED

BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE

BUILDING PLUMBING SYSTEM.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

PAGE 1 97570C (Rev. A - 05/00)

97570C (Rev. A - 05/00)

HT-EBP-FR HT-SEBP-FR

PAGE 2

1. Wall should already be framed for the fountain using dimensions shown in Fig. 1. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. (and ADA) (Framing shown for reference only).

2. Remove bottom cover from fountain and save the screws. Assemble push rod to fountain. (Push rod provided with frost-resistant box)

3. Install the fountain using bolts and washers (not provided). Tighten securely.

4. Attach drain tube to fountain and cut to required length using the frost resistant boxe as guides.

5. Install frost-resistant box - see box instructions.

6. Install a service stop (not provided) and make water supply connection from the stop to the strainer in the frost-resistant box.

7. Connect fountain water line to frost-resistant box - see box instructions. Replace bottom cover.

FIG. 1

FINISHED FLOOR

LEGEND

A = 3/8" DIA. (10mm) SLOT

B = 3/8" DIA. (10mm) HOLE

C = 1-3/4" (44mm) HOLE FOR WASTE LINE

D = 7/8" DIA. (22mm) HOLE FOR WATER INLET

E = 1" DIA. (25mm) HOLE FOR PUSH ROD

97570C (Rev. A - 05/00)

HT-EBP-FR HT-SEBP-FR

PAGE 3

FIG. 2

FINISHED FLOOR

97570C (Rev. A - 05/00)

HT-EBP-FR HT-SEBP-FR

1. Wall should already be framed for the fountains using dimensions shown in Fig. 3. Shown dimensions pertain to installation location.

These dimensions are required for compliance with ANSI Standard A117.1. (and ADA) (Framing shown for reference only).

2. Remove bottom covers from fountains and save the screws. Assemble push rods to fountains. (Push rods provided with frost-resistant boxes)

3. Install the fountains using bolts and washers (not provided). Tighten securely.

4. Attach drain tubes to fountains and cut to required length using the frost resistant boxes as guides.

5. Install frost-resistant boxes - see box instructions.

6. Install a service stops (not provided) and make water supply connections from the stops to the strainers in the frost-resistant boxes.

7. Connect fountain water lines to frost-resistant boxes - see box instructions. Replace bottom covers.

FIG. 3

LEGEND

A = 3/8" DIA. (10mm) SLOT

B = 3/8" DIA. (10mm) HOLE

C = 1-3/4" (44mm) HOLE FOR

WASTE LINE

D = 7/8" DIA. (22mm) HOLE FOR

WATER INLET

E = 1" DIA. (25mm) HOLE FOR

PUSH ROD

FINISHED FLOOR

PAGE 4

97570C (Rev. A - 05/00)

HT-EBP-FR HT-SEBP-FR

FINISHED FLOOR

FIG. 4

PAGE 5

97570C (Rev. A - 05/00)

HT-EBP-FR HT-SEBP-FR

4, 5, 6

FIG. 5

PAGE 6

97570C (Rev. A - 05/00)

HT-EBP-FR HT-SEBP-FR

STREAM HEIGHT ADJUSTMENT:

Stream height is factory set at 35 PSI. If supply pressure

varies greatly from this, adjust screw on regulator in freeze

resistant box. Clockwise adjustment will raise stream and

counter-clockwise adjustment will lower stream. For best

adjustment, stream should hit basin approximately 6-1/2" from

the bubbler.

Fig. 8

FIG. 6

TUBE IS

SECURED

IN POSITION

SIMPLY PUSH IN

TUBE TO ATTACH

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

FIG. 7

OPERATION OF QUICK CONNECT FITTINGS

NOTE: WATER FLOW

DIRECTION

BUILDING WATER INLET

SERVICE STOP

(NOT FURNISHED)

1/4" O.D. TUBE

WATER INLET

TO COOLER

3/8" O.D. UNPLATED

COPPER TUBE CONNECT

COLD WATER SUPPLY

PAGE 7

97570C (Rev. A - 05/00)

HT-EBP-FR HT-SEBP-FR

PAGE 8

DESCRIPTION

51546C

100322740560

66354C

66355C

160270508640

161637308650

100147140560

66346C

66343C

22913C

22915C

23001C

23002C

55864C

*55000458

*100813731870

*70054C

55884C

55885C

28016C

28017C

27083C

27090C

PART NO.

Bubbler

Gasket - Bubbler

Tube Assy - Bubbler (Long Ftn)

Tube Assy - Bubbler (Short Ftn)

Strainer Plate

Drain Plug

Gasket-Drain

Tube - Waste (Long Ftn)

Tube - Waste (Short Ftn)

Basin (Long Ftn)

Basin (Short Ftn)

Cover - Bottom (Long Ftn)

Cover - Bottom (Short Ftn)

Bushing - Snap 1/2" I.D.

Push Button Assy

Bushing - Snap

Nut - Speed

Elbow-Drain

Nut-Slip Joint

Panel - Single

Panel - Double

Mounting Bracket

Hanger Bracket

ITEM NO.

PARTS LIST

* PARTS SUPPLIED WITH FREEZE-RESISTANT BOX

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620

2222 CAMDEN COURT

OAK BROOK, IL 60521

630.574.3500

PRINTED IN U.S.A.

Halsey Taylor HTBPFP OLD MTG Owner's manual

Halsey Taylor HTBPFP OLD MTG Owner's manual

Halsey Taylor HTBPFP OLD MTG Owner's manual

Related papers

Other documents