Perle PINJ30 Installation guide
- Category
- Network switches
- Type
- Installation guide
Perle PINJ30 Gigabit PoE/PoE+ Injector. Extend the reach of your PoE devices and power them up with ease!
The Perle PINJ30 Gigabit PoE/PoE+ Injector is the perfect solution for extending the reach of your PoE devices, providing power and data to devices such as Wireless Access Points or IP Phones over a single Ethernet cable.
Key Features and Benefits of the Perle PINJ30:
- Compliant with IEEE802.3at and IEEE 802.3af standards, ensuring compatibility with a wide range of PoE devices.
- Gigabit Ethernet ports for fast and reliable data transfer speeds.
- Automatically detects if the connected device is PoE-enabled, preventing power from being sent to non-PoE devices.
Perle PINJ30 Gigabit PoE/PoE+ Injector. Extend the reach of your PoE devices and power them up with ease!
The Perle PINJ30 Gigabit PoE/PoE+ Injector is the perfect solution for extending the reach of your PoE devices, providing power and data to devices such as Wireless Access Points or IP Phones over a single Ethernet cable.
Key Features and Benefits of the Perle PINJ30:
- Compliant with IEEE802.3at and IEEE 802.3af standards, ensuring compatibility with a wide range of PoE devices.
- Gigabit Ethernet ports for fast and reliable data transfer speeds.
- Automatically detects if the connected device is PoE-enabled, preventing power from being sent to non-PoE devices.
Perle PINJ130
Gigabit PoE/PoE+ Injector
P/N 5500348-10 (Rev F)
Installation Guide
- 2 - PINJ130 Gigabit PoE/PoE+ Installation Guide
Introduction
The Perle PoE/PoE+ Injector is used to provide DC
voltage to the downstream device, such as a Wireless
Access Point or IP Phone when connected to a non-
PoE upstream switch port. The PoE/PoE+ Injector has
two Ethernet ports. One port connects to the non-PoE
upstream device, such as a router or switch. The other
port is a power sourcing port that connects to the
downstream device that is PoE/PoE+ capable.
http://www.perle.com/
Features
• Complies with IEEE802.3at and IEEE 802.3af
• 1-port 10/100/1000Mbps (Data) for connection to
passive LAN device
• 1-port 10/100/1000 Mbps (Power/Data) for
connection to PoE /PoE+ device
• Automatically detects if the connected device is
PoE-enabled to avoid sending power to a non-PoE
device
• Adds PoE/PoE+ capability to a non-PoE Ethernet
switch or router
• PoE status LED
• Rugged metal case
• Wall/panel mounting (screws not included)
Package Contents
• One PINJ130 (PoE/PoE+) Injector
• One country specific power cord
• This guide
PINJ130 Gigabit PoE/PoE+ Installation Guide - 3 -
Connecting the PINJ130 Injector
1. The PoE/Data port sends power and Ethernet data
to your PoE-enabled device. Use a CAT 5e cable or
better (see cabling requirements) to connect the
PoE/Data port to your PoE-enabled device.
2. The Data port doesn’t deliver power. Use an
Ethernet cable to connect to the injector’s Data port
to the LAN of an Ethernet device, such as an
Ethernet switch.
3. Use the included power cord to connect the
injector’s power socket to a power source.
- 4 - PINJ130 Gigabit PoE/PoE+ Installation Guide
LED Status (Green)
PWR– Power
On solid: Power present
Off: No Power present
PoE/Data (Green LED)
On solid : The PoE port is providing power
Off: The PoE port is not providing power
Ethernet Copper Cabling Requirements
• Category 5e or better (UTP or STP)
• 24-22 AWG
• Straight through or Ethernet crossover cable
Connect the copper cable from the Data port to an
Ethernet switch. See below for pinouts.
8-pin RJ-45
Remaining pins not used.
PINJ130 Gigabit PoE/PoE+ Installation Guide - 5 -
Cautions
Ensure that the voltage and current ratings of the
intended power source are appropriate for the Perle
Injector as indicated on the product label.
Ensure that the installation and electrical wiring of the
equipment is performed by trained and qualified
personnel and that the installation complies with all
local and national electrical codes
If this unit is to be installed in a location where the
ambient temperature exceeds 50C, the case
temperature may exceed safe levels. For this reason,
this unit should be installed in a restricted access
location where access can only be gained by service
personnel or users who have been instructed about the
reasons for the restrictions applied to the location and
about any precautions that shall be taken; and access
is through the use of a tool or lock and key, or other
means of security, and is controlled by the authority
responsible for the location.
- 6 - PINJ130 Gigabit PoE/PoE+ Installation Guide
Technical Specifications
Connection
Power Consumption
36.6 Watts maximum ( with 30W
PoE/PoE+ output
Power Input 100-240VAC, 50/60 Hz
Interface
Data Port (Ethernet–RJ45) 10/100/1000Base-T, auto
negotiation speed, F/H duplex
mode and auto MDI/MDI-X
connection
PoE/PoE+/Data Port (Ethernet –
RJ45)
LED Indicators PWR
green on, power on
off, no power
PoE/Data
green on (data or power),
off, no data or power
Cable Distance (mid-span) Total cable distance for both
ports combined should not
exceed 100 meters (328ft)
Environmental
Operating Temperature 0°C to 40°C (32°F to 104°F)
Storage Temperature -40°C to 70°C (-40°F to158°F)
Ambient Relative Humidity 10 – 95% (non-condensing)
Regulatory Approvals
Certifications CE, FCC Class A
PINJ130 Gigabit PoE/PoE+ Installation Guide - 7 -
Mechanical Drawings
- 8 - PINJ130 Gigabit PoE/PoE+ Installation Guide
Contacting Technical Support
Contact information for the Perle Technical Assistance Center
(PTAC) can be found at the link below. A Technical Support
Query may be made via this web page.
www.perle.com/support_services/support_request.shtml
Warranty / Registration
This product is covered by the Perle Ethernet Switches Warranty.
Details can be found at:
http://www.perle.com/support_services/warranty.shtml
Copyright © 2016 Perle Systems Limited all rights reserved. No
part of this document may be reproduced or used in any form
without written permission from Perle Systems Limited.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Perle PINJ30 Installation guide
- Category
- Network switches
- Type
- Installation guide
Perle PINJ30 Gigabit PoE/PoE+ Injector. Extend the reach of your PoE devices and power them up with ease!
The Perle PINJ30 Gigabit PoE/PoE+ Injector is the perfect solution for extending the reach of your PoE devices, providing power and data to devices such as Wireless Access Points or IP Phones over a single Ethernet cable.
Key Features and Benefits of the Perle PINJ30:
- Compliant with IEEE802.3at and IEEE 802.3af standards, ensuring compatibility with a wide range of PoE devices.
- Gigabit Ethernet ports for fast and reliable data transfer speeds.
- Automatically detects if the connected device is PoE-enabled, preventing power from being sent to non-PoE devices.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Perle IDS-509FPP Installation guide
-
-
-
-
-
-
Perle PoE Installation guide
-
-
-
Other documents
-
Perle Systems S-110P User manual
-
Perle Systems S-1110DP User manual
-
Epson Vision Guide User manual
-
ANTAIRA INJ-0200G-at-24-T User manual
-
CyberData 011187 Operations Guide
-
Interlogix 8-Port Unmanaged PoE-at Industrial Switch User manual
-
TP-LINK TL-POE10R Installation guide
-
MiLAN MIL-SM8TXAF2GPA User manual
-
LevelOne 150Mbps Wireless Outdoor PoE Access Point User manual
-
Dell 2808 User manual
