American Standard T430740.295 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
This manual is also suitable for
T430.740
T431.740
Installation
Instructions
M 9 6 5 0 0 3 R E V. 1.2 (1/15 )
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
ASSE 1016
ROUGHING-IN DIMENSIONS
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
CENTRAL THERMOSTAT
WITH VOLUME CONTROL
TRIM KIT
7-3/8"
(186mm)
3-7/8"
(100mm)
2
" TO 2-5/8"
(48mm TO 68mm)
NOTE: FITTING
MUST BE INSTALLED
WITH VOLUME CONTROL
ON TOP.
R520
1/2" NPT INLETS
or
R540
3/4" NPT INLETS
1"
(25mm)
FINISHED
WALL
7-1/16"
(179mm)
7-15/16"
(202mm)
6
"
(152mm)
CROSS
HANDLE
LEVER
HANDLE
CROSS
HANDLE
LEVER
HANDLE
BERWICK
™
/ BOULEVARD
™
M 9 6 5 0 0 3 R E V. 1.2 (1/15 )
12
INSTALL HANDLES
Should the hot and cold water supply pipes have been transposed making
adjustment impossible, proceed as follows:
TRANSPOSED SUPPLY PIPING
OR BACK TO BACK INSTALLATION
3
Remove check stops and re-install them transposed.
Shut off water supply.
Remove handle and rim. (Reverse steps 1 and 2).
CHECK STOP
(RED TO BLUE)
Turn the water supply back on and perform the temperature adjustment in step 4.
Assemble HANDLES and TRIM.
CHECK STOP
(BLUE TO RED)
Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE
CHECK STOP is now on the left.
8
1
9
2
7
4
4a
3
Thread HANDLE SCREW (1) into VALVE STEM (2) and tighten
to secure KNOB MOUNT (3).
Align HANDLE (4) and push onto KNOB MOUNT (3).
Tighten SET SCREW (5) in handle with HEX WRENCH (6) SUPPLIED.
Install HANDLE ADAPTER (7) onto TEMPERATURE CONTROL KNOB (8)
and tighten with SCREW (9).
Align HANDLE (4a) and push onto TEMPERATURE CONTROL KNOB (8).
Tighten SET SCREW (5a) in handle with HEX WRENCH (6) SUPPLIED.
5a
6
5
TOP
1
Remove PLASTER GUARD (1) if attached.
Push CAPS (2 & 2a) as shown onto CONTROL
VALVES (3).
Push ESCUTCHEON HOLDER (4) with lightly greased
O-RING SEALS (5) over CAPS (2, 2a). Attach with the
two SCREWS (6) provided.
Align pins in back of ESCUTCHEON (7) with holes in
ESCUTCHEON HOLDER (4) and push ESCUTCHEON
(7) into place.
1
TRIM INSTALLATION
2
2a
1
4
5
6
7
PINS
3
M 9 6 5 0 0 3 R E V. 1.2 (1/15 )
3
3
4
TEMPERATURE ADJUSTMENT
SET HOT LIMIT STOP
Check that arrow marking B points to the 12 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to
the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" 12 o'clock position. See Figure 1.
For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100˚F. Check
that arrow "A" on the KNOB MOUNT (3) still points 12 o'clock position after adjusting the thermostat to 100˚F.
If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT (3) by pulling it towards you while standing directly in
front of the valve.
Reinstall the KNOB MOUNT (3) with arrow "A" 12 o'clock position.
The maximum mixed water temperature is set at 109˚F at the factory. This setting can be changed if desired.
Remove the TEMPERATURE LIMIT STOP (H shaped Red Plastic part). Reinstall it at the desired notch as indicated in
the diagram to limit the maximum mixed water temperature to 104˚F or 112˚F.
Reinstall RED LOCKING DEVICE.
See Step 2 for HANDLE (2) installation.
Loosen SET SCREW (1). Pull off HANDLE ASSEMBLY (2).
ARROW
"A"
BLACK
CLAMP
ARROW
"B"
RED LOCKING
DEVICE
TEMPERATURE
LIMIT STOP
ARROWS AT 12 O'CLOCK
POSITION
Figure 1
KNOB MOUNT
112
109
104
1
2
M 9 6 5 0 0 3 R E V. 1.2 (1/15 )
MODEL NUMBER
A907090-YYY0A
CAP
M907592-YYY0A
ESCUTCHEON
M918318-YYY0A
HANDLE SCREW
CENTRAL THERMOSTAT
WITH VOLUME CONTROL
TRIM KIT
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2009
HOT LINE FOR HELP
M918038-0070A
ADAPTER
M918990-0070A
SELF TAPPING SCREW
Replace the "YYY" with
appropriate finish code
CHROME
SATIN NICKEL
002
295
T430.740 / T431.740
084045-0070A
SCREWS
M962853-YYY0A
CROSS HANDLE KIT
M962852-YYY0A
LEVER HANDLE KIT
M962630-0070A
ESCUTHEON HOLDER
BERWICK
™
/ BOULEVARD
™
-
1
-
2
-
3
-
4
American Standard T430740.295 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard T064.740.295 Installation guide
-
-
-
-
-
American Standard T010.430.075 Installation guide
-
-
-
-