AI-01 09/06
issue 181751
ASSEMBLY INSTRUCTIONS
!
BEFORE STARTING THIS
ASSEMBLY PLEASE TAKE TIME
TO FAMILIARISE YOURSELF
WITH THE COMPONENTS
LISTED ON THE BACK PAGE
Alphason Designs Limited
Alphason House, Bolton Road, Atherton, Greater Manchester M46 9AW UK
Tel: +44 (0)1942 885600
Fax: +44 (0)1942 876955
www.alphasondesigns.com
Alphason Designs Ltd. accepts no liability for any damage caused through incorrect or inappropriate use of this audio visual support.
Please Note:
Maximum load for this support is 80Kg.
This support must be assembled in accordance with these assembly instructions.
Maximum load for each glass shelf is 60kg.
A HAMMER
CROSS-HEAD SCREWDRIVER
PLEASE NOTE OTHER TOOLS REQUIRED:
MODEL: ABR800
AV CABINET
Place base panel on its back edge, on a clean flat
surface to avoid scratching. Using screws attach panels
to panel .
Insert 4X (Minifix cams) into large holes in panel .
Ensure arrows are pointing to the outside edge of the panel.
STAGE 1
•
•
STAGE 2
•
STAGE 3
•
•
1.1.
2.2.
3.3.
Slot back panel into grooves in sides of panels
and , and base panel .
D
D
E
C
D
s
u
u
A
A
s
C
C
C
B
r
STAGE 4
Screw all remaining dowels into top panel .
Take care not to over tighten.
r
B
s
u
s
r
r
r
4.4.
A
•
A
C
D
A
Ensure back panel is correctly located before
proceeding to next stage.
•
E
A
i
i
s
s
D
A
D
C
E
A
A
X4 X6
X4
X4
Position all remaining cams
in panels and . Once
again ensure the arrows are
pointing to the outside edge.
Screw dowels x4 into
panels and .
Assemble side panels and
onto panel . Tighten
cams in base panel .
X4
AI-01 09/06
issue 181751
Assemble top panel as shown in the diagram to the left.
Ensure dowel fixings align with corresponding holes in panels
and .
Tighten all cams that were put in place in stage 2.
STAGE 5
•
Position location tape pieces around the rebate in
cabinet door ensure these are equally spaced around
the rebate.
Place glass panel into the rebated area. Ensure this is
firmly stuck in place.
Fit all pine tree clips into correct holes in the cabinet
door . You may need a light hammer to get these in
to place. Take extra care when carrying out this step.Take extra care when carrying out this step.
STAGE 6
•
•
•
5.
6.
D
s
G
v
F
C
B
STAGE 7
Using screws attach flap hinges to base
panel .
v
t
t
7.
B
C
D
•
G
v
STAGE 8
•
8.
Using screws , screw flap hinges into cabinet
door .
Using screws attach touch plate from flap stay
into the two holes either side of door at the top.
•
G
n
n
k
A
A
X3
k
X9
X11
•
•
j
j
k
j
k
G
!
n
G
F
t
j
j
j
k
k
G
j
k
k
k
k
k
WARNINGWARNING
ENSURE CORRECT SCREWS ARE
USED
AT ALL STAGES
!
AI-01 09/06
issue 181751
n
TOUCH PLATE
X2
X10
X6
Attach left and right hand flap stays and
using screws .
If adjustment of flap stays is required, this can
be achieved by turning grey plastic column
shown in fig 9a below.
STAGE 9
•
Carefully lay the cabinet on its back. Push roller
glides into roller glide panels .
Turn cabinet around to sit on roller glides .
STAGE10
•
•
•
9.
10.
m
o
STAGE 11
Finally insert shelf pegs into
desired positions in the side panels.
Place glass shelf into cabinet.
11.
•
•
l
l
m
o
q
Congratulations! Your cabinet is
complete.
Adjustable
column.
o
q
o
9a.
p
p
p
i
p
i
p
h
q
h
The flap stays may require adjusting;
Screw clockwise to loosen the movement.
Screw anti-clockwise to tighten the movement.
AI-01 09/06
issue 181751
X4
X4
X10
DESCRIPTION
QTY
PACKED BY
1
1
2
1
COMPONENT
MODEL: ABR800
CERTIFICATE OF CONFORMITY
A
B
1
1
BACK PANEL
LEFT END PANEL
TOP PANEL
BASE PANEL
CABINET DOOR
1
GLASS SHELF
C
D
E
F
h
2
ROLLER GLIDE PANEL
i
G
RIGHT END PANEL
GLASS PANEL FOR DOOR
AI-01 09/06
issue 181751
(with pre fitted dowels)
(with pre fitted dowels)
This document is your guarantee that the product has reached you in the highest of quality
standards. Should you have any cause for complaint please return this document with your
correspondence to the address given at the bottom of the front page.
3
11
RIGHT HAND FLAP STAY
1
1
2
10
4
8
8
FLAP HINGE
6 x 1/2” SCREW
DESCRIPTION
QTY
PACKED BY
COMPONENT
SHELF PEG
34mm MINIFIX DOWEL
MINIFIX CAM
m
n
o
p
q
r
s
t
u
v
l
6 X 5/8” SCREW
4
ROLLER GLIDE
LEFT HAND FLAP STAY
TOUCH PLATE
8 X 1” SCREW
PINE TREE CLIP
6
6
10
8 X 20mm LOCATION TAPE
j
k
4 X 1/2” SCREW
9
W
AI-01 09/06
issue 181751
/
