Whirlpool is a registered trademark of Whirlpool USA.
5019 301 20053
Prewash cycle increases programme duration by approx. 15 minutes. Consumption data were measured in normalized
conditions in compliance with Standard IEC 60 456. The data on the “Energy Label” refer to programme “Coloured Cotton
60° C”. Consumption data in the home may vary with respect to the values in the table in relation to the water supply
pressure and temperature, the load and the type of wash.
Add the detergent as described in the programme
table or in the chapter “Detergent and Additives” in
the booklet.
1. Make sure that the
Programme selector
is set to
“Stop”
.
2. Open the tap.
3. Set the
Programme Selector
to the desired
programme.
4. Set the
thermostat knob
to the desired
temperature.
5. Set the
spin selector knob
to the desired speed.
6. Special options can be selected,
if required
.
7. Check that the door is well closed and turn on the
washing machine by pressing the
“ON/OFF”
button. The indicator lights up, indicating that
the washing machine is on.
“Half Load” button (depending on model)
• Reduces water consumption above all during
rinsing.
• Suitable for lightly soiled laundry and small loads
(max 2.5 kg).
Note:
reduce the detergent quantity.
“Intensive Rinse” button (depending on
model)
• More water and a longer time in rinse cycle is
added.
• This option is especially recommended in areas
with extremely soft water, for baby linen and
helps people with skin allergies.
“Rinse Hold” button (depending on model)
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programme “Synthetics” or “Delicate”.
• This function is particularly useful if you want to
postpone spinning to a later time or when you do
not wish to spin the clothes.
To terminate the “Rinse Hold”
option (depending on model)
in synthetic and wool programmes only
• Press the Rinse hold button again; the load will
be spun according to the selected programme.
If you do not wish to spin the clothes, turn the
programme selector knob to the drain programme,
after pressing the “No Spin” button.
CONSUMPTION DATA
Programme
Temperature
Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.
Programme
Duration
(hours:minutes)
2 - Cotton 90° 3.5 49 1.72 2:39
3 - Cotton 60° 3.5 48 0.85 2:40
4 - Cotton 45° 3.5 48 0.53 2:19
5 - Synthetics 60° 1.5 35 0.80 1:02
7 - Synthetics 45° 1.5 37 0.40 0:43
8 - Wool 40° 1.0 37 0.28 0:42
ADD DETERGENT, CLOSE THE DOOR AND SELECT
THE PROGRAMME
SELECT ANY DESIRED OPTION
“Eco Wash” button
(eco)
(depending
on model)
• Reduces the temperature to 60° when the
thermostat is set to a higher temperature.
“No Spin” button
• Especially for delicate garments to avoid wear
and tear caused by the spin.
Note:
in the “Cotton” and “Synthetics”
programmes the machine will perform a short spin
at a low speed, even if the spin cycle has been
disabled, so as to optimise rinsing operations.
The door locks automatically after the programme
start until the end of the programme. If the
programme selector is moved to the “Stop”
position or if the electricity supply is interrupted,
then after approximately two minutes the door is
released. In this case do not open the door,
because hot water could come out of the door.
To change a programme when a cycle has already
begun:
1. Switch off the appliance by pressing the
“
ON/OFF
” button.
2. Select the new programme.
3. Start the programme by pressing the
“
ON/OFF
” button.
To interrupt the running programme and continue
it at a later time:
1. Press the
“ON/OFF”
button.
2. After the desired interval has passed, press the
“ON/OFF”
button again.
1. At the end of the programme the programme
selector moves to the “Stop” position.
2. To unload the machine wait for the door to
unlock (approx. 2 minutes).
3. Switch off the appliance, open the door and
unload the washing.
4. Close the tap and leave the door ajar to allow
the drum to dry out.
•
SPIN SPEED CONTROL
Spin speed may be reduced automatically or
may even be excluded in case of small loads
containing highly absorbing garments (e.g.
bath robes, towels, etc).
This reduces damage to fabric and to the
machine and prevents excessive vibration and
noise in the machine due to an unbalanced
load: by selecting high spin speeds the noise
level increases.
•
CLEANING THE FILTER
To ensure an impeccable function of the pump,
check the filter regular and clean it if necessary.
•
THERMOSTAT KNOB
This is set by turning the knob until it reaches
the desired temperature.
DOOR LOCK
PROGRAMME RESELECTION
TO INTERRUPT THE RUNNING PROGRAMME
END OF WASH CYCLE
NOTES AND INDICATIONS FOR USE
3gb20053.fm5 Page 2 Tuesday, April 17, 2001 4:54 PM
Black Process Plate