Woodbridge Fireplace Inc NEWPORT-P Installation And Operating Instructions Manual

Brand: Woodbridge Fireplace Inc

Model: NEWPORT-P

Category: Fireplaces

Type: Installation And Operating Instructions Manual

This manual is also suitable for

DIRECT VENT GAS FIREPLACE

WITH ELECTRONIC IGNITION SYSTEM

MODELS: MONTEREY-(N,P)-E

Woodbridge Fireplace Inc.

WARNING: This

fireplace requires

one foot of vertical

venting before

any horizontal runs

INSTALLATION AND OPERATING INSTRUCTIONS

– Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

– WHAT TO DO IF YOU SMELL GAS

department.

– Installation and service must be per formed

by a qualified installer, service agency or the

gas supplier.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certified

kit is used.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Version française de ce manuel est disponible à partir du site WEB : www.woodbridgefp.com

This appliance may be installed in an aftermarket,

permanently located, manufactured home

(USA

only)

or mobile home

where not

prohibited by local

codes.

WARNING: FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in

serious injury, death, or property damage.

•Do not touch any electrical switch; do not use any

phone in your building.

•Do not try to light any appliance.

phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire

WARNING: Improper installation, adjustment, alteration,

services or maintenance can cause injury or property

damage. Refer to this manual. For assistance or

additional information consult a qualified installer,

service agency or the gas supplier.

LOTHING OR OTHER FLAMMABLE

ATERIAL SHOULD NOT BE PLACED ON

R NEAR THE APPLIANCE.

OUNG CHILDREN SHOULD BE

UPERVISED WHEN THEY ARE IN THE

AME ROOM AS THE APPLIANCE.

CHILDREN AND ADULTS SHOULD BE

ALERTED TO THE HAZARDS OF HIGH

SURFACE TEMPERATURE AND

SHOULD

STAY AWAY TO AVOID BURNS OR

CLOTHING IGNITION.

DUE TO HIGH TEMPERATURES, THE

APPLIANCE SHOULD BE LOCATED OUT

OF TRAFFIC AND AWAY FROM FURNITURE

AND DRAPERIES.

•Leave the building immediately.

•Immediately call your gas supplier from a neighbor's

EEP THE ROOM AREA CLEARAND

REE

FROM COMBUSTIBLE MATERIALS,

ASO-

LINE, AND OTHER FLAMMABLE

APORS

AND LIQUIDS.

Report 0401GF009S

L100001 3

CONTENTS

Important Safety Information .......................... 3

Product Features............................................ 5

Code Approval ................................................ 5

Pre-Installation Information............................. 6

Installing Above 2000 Feet .......................... 6

Orice Sizes, Pressures and BTUs ................ 6

Before You Install ........................................ 6

Fireplace Framing ........................................ 7

Fireplace Dimensions .................................. 8

Fireplace Location ....................................... 9

Securing Fireplace to Floor or Framing .......... 10

Clearances................................................... 11

Installation Information................................. 12

Vent Installation ........................................... 13

Installation Precautions ............................. 13

Installation Planning .................................. 14

Rear Wall Vent Installation ......................... 17

Horizontal Termination Conguration........... 19

Below Grade Installation ............................ 21

Vertical Through-the-Roof Installation .......... 22

Installation for Vertical Termination..............23

Cathedral Ceiling Installation...................... 24

Fireplace Installation .................................... 25

Check Gas Type ........................................ 25

Installing Gas Piping to Fireplace/Burner

System Location ....................................... 25

Checking Gas Pressure................................. 27

Electrical Installation.................................... 28

Glass Removal ............................................. 29

Final Installation........................................... 30

Media Tray Placement ..........................

Replacement Parts........................................ 41

Vent Components...................................... 41

Firebox Components.................................. 42

Troubleshooting............................................. 45

Warranty ......................................... Back Cover

IMPORTANT

This fireplace is designed for a minimum 1 foot of vertical vent pipe rise before any horizontal vent pipe run.

See pages 13-14 for Vent Installation details.

.. 30

Log Set Placement...................................... 31

Safety Screen Installation ........................... 33

Operating Instructions................................. 35

What To Do If You Smell Gas...................... 3

Lighting Pilot for the First Time.................. 3

Lighting Pilot............................................. 3

Lighting Burner.......................................... 3

To Turn Off Gas.......................................... 37

Electrical Wiring ........................................ 28

Cleaning and Maintenance............................. 39

Burner, Pilot and Control Compartment........ 39

Pilot Flame ............................................... 39

Burner Flame ............................................. 39

Air Shutter Assembly ...................................39

Vent System .............................................. 40

Glass Panel................................................ 40

Media .......................................................... 40

Fan Assembly............................................ 27,40

2L100001

4. Never install the replace

• in a recreational vehicle

• where curtains, furniture, clothing, or other ammable

objects are less than 42" from the front, top, or sides of

the replace

• in high trafc areas

• in windy or drafty areas

5. This replace reaches high temperatures. Keep children and

adults away from hot surfaces to avoid burns or clothing

ignition. Fireplace will remain hot for a time after shutdown.

Allow surfaces to cool before touching.

6. Carefully supervise young children when they are in the

room with replace.

7. Do not modify replace under any circumstances. Any parts

removed for servicing must be replaced prior to operating

replace.

8. Turn replace off and let cool before servicing, installing,

or repairing. Only a qualied service person should install,

service, or repair the replace. Have burner system inspected

annually by a qualied service person.

9. You must keep control compartments, burners, and cir-

culating air passages clean. More frequent cleaning may

be needed due to excessive lint and dust from carpeting,

bedding material, pet hair, etc. Turn off the gas valve and

pilot light before cleaning replace.

10. Have venting system inspected annually by a qualied

service person. If needed, have venting system cleaned or

repaired. See Cleaning and Maintenance, page 37.

11. Keep the area around your replace clear of combustible

materials, gasoline, and other ammable vapor and liquids.

Do not run replace where these are used or stored. Do not

place items such as clothing or decorations on or around

replace.

INSTALLER

Please leave these instructions with the owner.

OWNER

Please retain these instructions for future reference

IMPORTANT SAFETY INFORMATION

This replace is a vented product. This replace must be properly

installed by a qualied service person. The glass panel must be

properly seated and sealed. If this unit is not properly installed

by a qualied service person with glass panel properly seated and

sealed, combustion leakage can occur.

CARBON MONOXIDE POISONING: Early signs of carbon

monoxide poisoning are similar to the u with headaches, diz-

ziness and/or nausea. If you have these signs, the replace may

not have been installed properly. Get fresh air at once! Have the

replace inspected and serviced by a qualied service person.

Some people are more affected by carbon monoxide than others.

These include pregnant women, people with heart or lung dis-

ease or anemia, those under the inuence of alcohol, and those

at high altitudes.

Propane/LP gas and natural gas are both odorless. An odor-

making agent is added to each of these gases. The odor helps

you detect a gas leak. However, the odor added to these gases

can fade. Gas may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this

manual for reference. It is your guide to safe and proper opera-

tion of this replace.

1. This appliance is only for use with the type of gas indicated

on the rating plate. This appliance is not convertible for use

with other gases unless a certied kit is used.

2. For propane/LP replace, do not place propane/LP supply

tank(s) inside any structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance problems, do not

use propane/LP fuel tank of less than 100 lbs. capacity.

3. If you smell gas

• shut off gas supply.

• do not try to light any appliance.

• do not touch any electrical switch; do not use any phone

in your building .

• immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

Continued on page 4

• Read this owner’s manual carefully and completely before trying to assemble, operate,

or service this fireplace.

• Any change to this fireplace or its controls can be dangerous.

• Improper installation or use of this fireplace can cause serious injury or death from fire,

burns, explosions, electrical shock and carbon monoxide poisoning.

WARNING

L100001 5

IMPORTANT SAFETY INFORMATION

Continued from page 3

12. Do not use this replace to cook food or burn paper or

other objects.

13. Never place anything on top of replace.

14. Do not use any solid fuels (wood, coal, paper, cardboard,

etc.) in this replace. Use only the gas type indicated on

rating plate.

15. This appliance, when installed, must be electrically

grounded in accordance with local codes or in the absence

of local codes, with the National Electrical Code, ANSI/

NFPA 70, or the Canadian Electrical Code, CSA C22.1.

16. Do not obstruct the ow of combustion and ventilation air

in any way. Provide adequate clearances around air open-

ings into the combustion chamber along with adequate

accessibility clearance for servicing and proper operation.

17. When the appliance is installed directly on carpeting

or other combustible material other than wood ooring,

you must set appliance on a metal or wood panel or hearth

pad extending the full width and depth of the appliance.

18. Do not use replace if any part has been exposed to or

has been under water. Immediately call a qualied service

person to arrange for replacement of the unit.

IMPORTANT:

PLEASE READ THE FOLLOWING CAREFULLY

It is normal for replaces fabricated of steel to give off some

expansion and/or contraction noises during the start up or

cool down cycle. Similar noises are found with your furnace

heat exchanger or car engine.

IMPORTANT:

PLEASE READ THE FOLLOWING CAREFULLY

It is not unusual for a gas fireplace to give off some

odor the first time it is burned. This is due to the

manufacturing process.

Please ensure that your room is well ventilated

during burn off — open all windows.

It is recommended that you burn your replace for at least

ten (10) hours the rst time you use it. Place the fan switch

in the “OFF” position during this time.

A manufactured home (USA only) or mobile home OEM

installation must conform with the

Manufactured Home

Construction and Safety Standard, Tile 24 CFR, Part 3280,

or, when such a standard is not applicable, the Standard

for Manufactured Home Installations, ANSI/NCSBCS

A225.1

, or Standard for

Gas Equiped Recreational Vehicles

and Mobile Housing, CSA Z240.4.

19.Do not use a blower insert, heat exchanger insert, or any

other accessory not approved for use with this replace.

20.Do not operate the replace with glass panel removed,

cracked, or broken.

21. Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children,

and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals

in the house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children, and

other at risk individuals out of the room and away from hot surfaces.

the appliance.

22. Any safety screen or guard removed for servicing an appliance must be replaced prior to operating

23. Handle glass door with care to avoid striking or scratching it on hard objects. WARNING: Do not operate appliance

with the glass front removed, cracked or broken. Replacement of the glass should be done by a licensed or qualified

service person.

24. Installation and repair should be done by a qualified service person. The appliance should be inspected before use and

at least annually by a profesional service person. More frequent cleaning may be required due to excessive lint from

carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageway of

the appliance be kept clean.

4L100001

PRODUCT FEATURES AND CODE APPROVAL

Figure 1 - Fireplace controls

PRODUCT SPECIFICATIONS FIREPLACE CONTROLS

(see Figure 1)

1- Remote Control Receiver

2- Blower Speed Control with Manual On/Off Switch

3- Power Outlet to Connect Blower or Optional AUX Block

4- Gas Manual Shut-Off Valve

5- Main Gas Control Valve

7- Thermostat Blower

6- Electronic Control DFC Board

•The appliance must be properly

connected to a venting system.

•The appliance is not approved for

closet or recessed installations.

• This appliance has been certied

for use with either natural or

propane gas. See appropriate data

plates.

• This appliance is not for use with

solid fuels.

• The appliance is approved for bed-

room or bedsitting room installa-

tions.

CSA B149.1 in Canada.

Gas and Propane Installation Code,

NFPA54 in U.S.A., or the Natural

Fuel Gas Code, ANSI Z223.1/

of local codes, with the National

with local codes or, in the absence

•The installation must conform

TESTED TO: ANSI Z21.88-2014/CSA 2.33-2014, CGA 2.17-M91 (R2009), CSA P.4.1-09 STANDARDS

LISTED VENTED GAS FIREPLACE HEATER

Direct Vent type appliances draw all combustion air from outside of the dwelling through the vent pipe.

CODE APPROVAL

These appliances have been listed by OMNI and found to comply with the established standards for DIRECT VENT GAS

FIREPLACE HEATERS in the USA and Canada as follows:

This appliance may be installed in an aftermarket, permanently located, manufactured home

(USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate.

This appliance is not convertible for use with other gases, unless a certified kit is used.

L100001 7

35(,167$//$7,21,1)250$7,21

INSTALLING ABOVE 2000 FEET

•In the USA, the appliance must be derated 4% for every 1,000 ft above 2,000 ft elevations (at the factory).

• In Canada, these appliances are certied for altitudes of 0 – 4,500 ft.

ORIFICE SIZES, PRESSURES AND BTUs

NATURAL GAS PROPANE GAS

Manifold Press: (W.C.) 3.5" Manifold Press: (W.C.) 10"

Maximum Supply Pressure 10.5" Maximum Supply Pressure 13"

Minimum Supply Pressure 4.5" Minimum Supply Pressure 11"

BEFORE YOU START

Read this homeowner'smanual thoroughly and follow all instructions carefully. Inspect all contents for shipping damage and

immediately inform the distributor if any damage is found. Do not install any unit with damaged, incomplete, or substitute parts.

Check your packing list to verify that all listed parts have been received.

ITEMS REQUIRED FOR INSTALLATION

Tools: Building Supplies:

• Phillips Screwdriver • Framing Materials

• Hammer • Wall Finishing Materials

• Saw and/or saber saw • Caulking Material (Noncombustible)

• Level • Fireplace Surround Material (Noncombustible)

• Measuring Tape • Piping Complying with Local Codes

• Electric Drill and Bits • Tee Joint

• Pliers • Pipe Sealant Approved for use with Propane/LPG

• Square (Resistant to Sulfur Compounds)

• Pipe Wrench

Natural #31 39,000 27,000

MONTEREY-P-E

Propane #49 38,000 27,000

Model # Gas Type Orifice Size Input Rate, Btu/hr

Max Min

MONTEREY-N-E

6L100001

PLANING FIREPLACE FRAMING AND COVERING FACE

Firebox framing can be built before or after the appliance is set in place. Construct rebox framing following Figure 2 and the

chart below for your specic installation requirements. See Figure 3 on Page 8 for rebox dimensions. The framing headers may

rest on the top of the rebox standoff.

The rebox may be installed directly on a combustible oor or raised on a platform of an appropriate height. When the rebox

is installed directly on carpeting, tile, or other combustible material, other than wood ooring, the rebox shall be installed on a

metal or wood panel extending the full width and depth of the enclosure.

Figure 2 - Framing Dimensions

WARNING IMPORTANT: The following must be taken into consideration if

you decide to cover over the fireplace face:

1. The covering material must be non combustible, maximum 3/4" thick.

2. Minimum outside dimensions of the material over the facing are

60" x 34-1/2" (see Figure 2).

3. The inner opening in covering material must be minimum 49-1/4" wide, 14-1/4" tall and centered over the fireplace opening to

allow for or glass door removal. A 1/4" reveal must be provided all the way around the fireplace opening.

4. The cover should maintain an air gap of at least 1/8" between covering material and fireplace to allow for metal fireplace front

to expand and contract during operation.

Do not fill spaces around firebox with insulation

or other materials. This could cause a fire.

PLEASE NOTE: Natural stone products may react to heat by discoloring or cracking. Woodbridge Fireplace Inc. is not

responsible" for any damages due to covering materials used. If tiles are to be applied covering the fireplace face, a layer of

cement board must be used as a substrate.

INSIDE CHASE INSTALLATION RECESSED INSTALLATION

MONTEREY

FRAMING DIMENSIONS

Note: These dimensions are for combustible framing

34.5"

6.5"

23.75"

FOR COVERING FIREPLACE FACE

NON COMBUSTIBLE

60"

34.5"

13"

COMBUSTIBLE

60"

60" 60"

MINIMUM DIMENSIONS

49-1/4"

L100001 9

PRE-INSTALLATION INFORMATION

Figure 3 - Fireplace Dimensions

Right side view

Front view

Top view

Flue collar

Electric

access

both

sides

Gas line access both sides

28"

34.25"

23.25"

48.75"

13.75"

59.25"

34.25"

28"

7.125"

8" 5"

22.25"

57.25"

8L100001













PRE-INSTALLATION INFORMATION

FIREPLACE LOCATION

Plan for the installation of your appliance. This includes determining where the unit is to be installed, the vent conguration to be

used, framing and nishing details, and whether any optional accessories (i.e. wall switch, or remote control) are desired.

Consult your local building code agency to ensure compliance with local codes, including permits and inspections.

The following factors should be taken into consideration:

• Clearance to side-wall, ceiling, woodwork, and windows. Minimum clearances to combustibles must be maintained.

• This replace may be installed along a wall, across a corner, or use an exterior chase. See Figure 4 for suggested locations.

• Location should be out of high trafc areas and away from furniture and draperies due to heat from appliance.

• Never obstruct the front opening of the replace.

• Do not install in the vicinity where gasoline or other ammable liquids may be stored.

• Vent pipe routing. See Venting section found in this manual for allowable venting congurations.

•These units can be installed in a bedroom or bathroom. See National Fuel Gas Code ANSI Z233.1/NFPA 54 (current edition),

the Uniform Mechanical Code — (current edition), and Local Building Codes for specic installation requirements.

Figure 4 - Locating Gas Fireplace

A Flat on Wall

B Cross Corner

C Island**

D Room Divider*

E Flat on Wall Corner*

F Chase Installation

Y 7" Minimum

** Island (C) and room divider (D) installation is possible as long as the horizontal portion of vent system (X)

does not exceed 20'. See Installing Horizontal Termination Configuration on pages 18 and 19.

* When you install your fireplace in (D) room divider or (E) flat on wall corner positions (Y), a minimum of 7"

clearance must be maintained from perpendicular wall and front of fireplace.

____

__ ____

____

__ __

to opening

L100001 11

The replace must be secured to the oor and/or to framing studs as shown in Figure 5. Use two (2) wood screws or masonry/

concrete screws to secure replace to the oor. Use four (4) screws to attach replace to framing. The side brackets are adjustable

from 1/2" to 5/8" to accommodate different thickness of material.

SECURING FIREPLACE TO FLOOR OR FRAMING

Figure 5 - Securing Fireplace to Floor and Framing Studs

Framing

Screws

Side adjustable bracket Screws

Side adjustable bracket

Screws

NOTE: If installed in mobile home, fireplace must be bolted securely to floor

10 L100001

CLEARANCES

CLEARANCES TO COMBUSTIBLES

MANTEL CLEARANCES

NOTE: The combustible area above the facing must not protrude more than 3/4" from the facing. If it does, it is

considered a mantel and must meet the mantel requirements listed in this manual.

Follow these instructions carefully to ensure safe installation. Failure to follow instructions

exactly can create a fire hazard.

The appliance cannot be installed on a carpet, tile or other combustible material other

than wood flooring. If installed on carpet or vinyl flooring, the appliance shall be installed

on a metal, wood or noncombustible material panel extending full width and depth of

the appliance.

WARNING

The fireplace face may be

covered with any non-

combustible material.

Allow clearance for removal

of front air panel and glass door.

14" min

48" min

Minimum 7"

from both

side walls

12"

maximum

depth

COMBUSTIBLE MANTEL

to ceiling

Clearance to

Combustibles

0.75 1 1.25 1.5 1.75 2 2.25 2.5

2.5

2.25

2.0

1.75

1.5

1.25

1.0

0.75

*Minimum 7 inches from Side Wall to Fireplace opening

Figure 6 - Side Clearance Chart

(159 mm)

Top 6.25

To top standoff 0" (0 mm)

Sides

1" (26 mm)

To side standoffs 0" (0 mm)

B a c k1. 5 " (38 mm)

To back standoffs 0" (0 mm)

Floor 0" (0 mm)

Front 36" (915 mm)

L100001 13

INSTALLATION PRECAUTIONS

Consult local building codes before beginning the installation. The installer must make sure to select the proper vent system for

installation. Before installing vent kit, the installer must read this replace manual and vent kit instructions.

Only a qualied installer/service person should install venting system. The installer must follow these safety rules:

• Wear gloves and safety glasses for protection.

• Use extreme caution when using ladders or when on rooftops.

• Be aware of electrical wiring locations in walls and ceilings.

The following actions will void the warranty on your fireplace:

• Installation of any damaged venting component.

• Unauthorized modication of the venting system.

•Installation of any component part not manufactured or approved by Woodbridge Fireplace Inc.

• Installation other than permitted by these instructions.

FINISHING MATERIAL

NOTE: Any remote wiring (i.e. remote control, wall switch) must be done prior to nal nishing to avoid costly

reconstruction.

INSTALLATION INFORMATION

VENT INSTALLATION

Never obstruct or modify the air inlet or outlet. This may create a fire hazard.

WARNING

Read all instructions completely and thoroughly before attempting installation. Failure to

do so could result in serious injury, property damage or loss of life. Operation of improperly

installed and maintained venting system could result in serious injury, property damage

or loss of life.

Failure to follow these instructions will void

the warranty.

NOTICE

WARNING

State of Massachusetts:

The installation must

be done by a licensed

plumber or gas tter in

the Commonwealth of

Massachusetts.

12 L100001

VENT INSTALLATION

Figure 7 - Combustible Clearances for Vent Pipe

A Minimum of 3" Clearance to the Top Is

Required Along Horizontal Length of Pipe until

Flue Pipe Goes Through Nearest Wall.

WARNING

This fireplace must be vented to the outside. The venting system must NEVER be attached

to a chimney serving a separate solid fuel burning appliance. Each gas appliance must

use a separate vent system. Do not use common vent systems.

WARNING

Horizontal sections of this vent system require

a minimum clearance of 3" from the top of

the pipe and 1" minimum to the sides and

bottom. Vertical sections of this system require

a minimum of 1" clearance to combustible

materials on all sides of the pipe.

WARNING

1" Clearance Is Acceptable

at the Outside Wall.

3



L100001 15

VENT INSTALLATION

INSTALLATION PLANNING

There are two basic types of direct-vent installation:

• Horizontal Termination

• Vertical Termination

It is important to select the proper length of vent pipe for the type of termination you choose. It is also important to note the

wall thickness. Venting terminals shall never be recessed into a wall or siding.

FOR HORIZONTAL TERMINATION

Select the amount of vertical rise desired. All horizontal run of venting

must have 1/4" rise for every 12" of run towards the termination.

You may use up to three 90° elbows in this vent conguration. See

Horizontal Termination Congurations on pages 19 and 20.

FOR VERTICAL TERMINATION

Measure the distance from the replace oor to the ceiling. Add the ceiling thickness, the vertical rise in an attic or second story,

and allow for sufcient vent height above the roof line.

NOTE: You may use two 45° elbows in place of a 90° elbow. You must follow rise to run ratios when using 45° elbows.

The appliance is approved for use with three 90° elbows maximum or a combination of 90° and 45° elbows up to a

maximum of 270°.

For two-story applications, restops are required at each oor level. If an offset is needed in the attic, additional pipe and elbows

will be required.

You may use a chase with a vent termination with exposed pipe on the exterior of the house. See Installing Vent System in a Chase

below. If pipe is enclosed in chase, it is not exposed.

It is very important that the venting system maintain its balance between the combustion air intake and the ue gas exhaust.

Certain limitations apply to vent congurations and must be strictly followed.

INSTALLING A VENT SYSTEM IN AN OUTSIDE CHASE

A chase is a vertical boxlike structure built to enclose venting that runs along the outside of a building. A chase is required for

such venting.

Never run the vent pipe level or downward.

This may cause excessive temperatures which

could cause a fire.

WARNING

When installing in a chase, you should insulate the chase as you would the outside walls of

your home. This is especially important in cold climates. Insulation should be considered

a combustible material. Maintain proper clearances to all combustible materials.

NOTICE

Treatment of firestops and construction of the chase may vary from building type to

building type. These instructions are not substitutes for the requirements of local building

codes. You must follow all local building codes.

NOTICE

14 L100001

















 





















 













VENT INSTALLATION

Figure 8 - Horizontal Vent Termination Location

Vent Terminal Air Supply Inlet Area Where Terminals Not Permitted

Inside Corner Detail

FOR HORIZONTAL TERMINATION

MINIMUM DISTANCES

A = Clearance above the grade, a veranda, porch, deck, or balcony [*12" (305mm) minimum].

B = Clearance to window or door that may be opened [*12" (305mm) minimum].

C = Clearance to permanently closed window [*minimum 12" (305mm) recommended to prevent condensation on window]

D = Vertical clearance to ventilated soft located above the terminal within a horizontal distance of two (2) feet (610mm) from

the centerline of the terminal [18" (457mm) minimum].

E = Clearance to unventilated softs [12" (305mm) minimum]. Clearance to vinyl soft [30" (762mm)].

F = Clearance to an outside corner [*6" (152mm) minimum].

G = Clearance to an inside corner [*6" (152mm) minimum].

H = *Not to be installed above a gas meter/regulator assembly within three (3) feet (914mm) horizontally from the centerline of

the regulator.

I = Clearance to service regulator vent outlet [*3' (914mm) minimum].

J = Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance [*12"

(305mm)minimum].

K = Clearance to a mechanical air supply inlet [*6' (1829mm) minimum].

L = Clearance above a paved sidewalk or paved driveway located on public property [**7' (2133mm) minimum].

M = Clearance under veranda, porch, deck, or balcony [*12" (305mm) minimum***].

N = Clearance above a roof shall extend a minimum of 24" (610mm) above the highest point when it passes through the roof

surface and any other obstruction within a horizontal distance of 18" (457mm).

* As specied in CAN/CGA B149 Installation Codes. Note: Local codes or regulations may require different clearances.

** A vent must not terminate directly above a sidewalk or paved driveway, which is located between two single-family dwellings

and serves both dwellings.

*** Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the oor.

Always maintain minimum clearances around vent systems. The minimum clearances to

combustibles for horizontal vent pipe are 3" at the top and 1" at the sides and bottom of

the vent system until the pipe penetrates the nearest vertical wall. A 1" minimum clearance

all around the pipe must be maintained. Do not pack the open air spaces with insulation

or other materials. This could cause high temperatures and may present a fire hazard.

WARNING

L100001 17



 

 





12305

2305

 



12305

   







      

  

       

 

   

   

     



652

   









 

 

 

       

 

VENT INSTALLATION

TERMINATION CLEARANCES FOR BUILDINGS WITH COMBUSTIBLE

AND NONCOMBUSTIBLE EXTERIORS

Figure 9 - Allowable Venting Chart

HOW TO USE THE VENT GRAPH

The Vent Graph should be read in conjunction with the following

vent installation instructions to determine the relationship between

the vertical and horizontal dimensions of the vent system.

1. Determine the height of the center of the horizontal vent pipe exit-

ing through the outer wall. Using this dimension on the Sidewall

Vent Graph below, locate the point intersecting with the slanted

graph line.

2. From the point of this intersection, draw a vertical line to the

bottom of the graph.

3. Select the indicated dimension, and position the replace in

accordance with same.

Example: If the vertical dimension from the floor of the

fireplace is 11' (3.4m) the horizontal run to the face of the

outer wall must not exceed 18' (5.5m).

Example: If the vertical dimension from the floor of the unit

is 7’ (2.14m), the horizontal run to the face of the outer

wall must not exceed 16' (4.9m).

Sidewall Vent Graph showing the relationship between vertical and

horizontal dimensions for a Direct Vent ue system.

Figure 10 - Rear Wall Venting Graph

Horizontal Dimension (Ft) From the Outside of

Termination to the Back of the Fireplace

Vertical Dimension (Ft) From the Floor of Unit to the Center of

the Horizontal Vent Pipe

2 4 6 8 16 18 20 (ft)141210

16 L100001

10

67

10

67

5.25

134

8

216

Figure 12 - Vent Opening Requirements

Note: Horizontal runs of vent must

be supported every three feet

(914mm). Use wall straps for this

purpose.

Figure 13 - Rigid Vent Pipe Connections

Female Locking Lugs

Male Slots

REAR WALL VENT INSTALLATION

When installed as a rear vent unit this appliance may be vented directly to a termination located on the rear wall behind

the appliance with 1' of vertical rise minimum.

The maximum horizontal distance between the rear of the appliance and the outside of termination is 20" (508 m). See

Figure 11.

VENTING INSTALLATION

1. Locate and cut the vent opening in the wall. For com-

bustible walls rst frame in opening. See Figure 11.

Combustible Walls: Cut a 101⁄2"H x 101⁄2" W

(267mm x 267mm) hole through the exterior wall

and frame as shown. See Figure 12.

Noncombustible Walls: Hole opening should be

81⁄2" (216mm) in diameter.

2. Rigid vent pipes and ttings have special twist-lock

connections. Assemble the desired combination of

pipe and elbows to the appliance adaptor with pipe

seams oriented towards the wall or oor.

Twist-lock Procedure:

The female ends of the pipes

and ttings have three locking lugs (indentations).

These lugs will slide straight into matching slots on

the male end of adjacent pipes and ttings. Push

the pipe sections together and twist one section

clockwise approximately one-quarter turn until the

sections are fully locked. See Figure 13.

Figure 11 - Rear Vent Application,

Maximum Horizontal Distance

Maximum

20"

3. Attach vent pipe assembly to the replace. Set re-

place in front of its permanent location to insure

minimum clearances. Mark the wall for a 101⁄2"H

x 101

/2" [216mm] diameter hole is accept-

able). See Figure 11. The center of the hole should

line up with the center line of the horizontal rigid

vent pipe end. Be sure to allow for minimum rise. Cut a 10-

/2"x10-

/2" (267mm X 267mm) square hole through combustible

exterior wall (8

/2" [216mm] diameter hole if noncombustible). Frame as necessary. Allow

⁄2"W (2

mm x 2

mm) square hole

(for noncombustible material such as masonry

block or concrete, a 8

/4" minimum rise per foot. See

L100001 19

HOT

VENT INSTALLATION

4. Apply a bead of non-hardening mastic around the outside

edge of vent cap. Position the vent cap in the center of hole

on the exterior wall with the word “UP” on the vent cap

facing up. Insure proper clearance of 1" to combustibles is

maintained. Attach the vent cap with four wood screws sup-

plied. See Figure 14.

NOTE: Replace the wood screws with appropriate fasteners

for stucco, brick, concrete, or other types of siding.

For vinyl siding, stucco, or wood exterior use vinyl siding stand-

offs between vent cap and exterior wall. The vinyl siding standoff

prevents excessive heat from melting the vinyl siding material. Bolt

the vent cap to the standoff. Apply non-hardening mastic around

outside edge of the standoff instead of the vent cap assembly. Use

wood screws provided to attach the standoff. See Figure 15.

5. Slide the wall thimble over the vent pipe before connecting

the horizontal run to the vent cap. See Figure 16.

6. Carefully move the replace with vent assembly attached

toward the wall and insert the vent pipe into the horizontal

termination. The pipe overlap should be a minimum of 11/4".

Apply silicone to the outer pipe connection. Fasten all vent

connections with screws provided.

7. Slide the wall thimble against the interior wall surface and

attach with srews. See Figure 16.

Figure 14 - Installing Horizontal Vent Cap

REAR WALL VENT INSTALLATION (continued)

Figure 15 - Installing Vinyl Siding Standoff

Apply Mastic

to All Four

Sides

Vent Cap

Wood

Screw

Cut Vinyl Siding Away to

Fit Standoff

Wood Screw

Vent Cap

Bolt

Apply Mastic to All

Four Sides

Nut

Standoff

Figure 16 - Connecting Vent Cap with Horizontal Vent Pipe

Interior Wall

Surface

Decorative

Wall Thimble

Horizontal

Vent Pipe

Screw

Vent Cap

(Horizontal

Termination)

Deecting Shield

Do not recess vent termination into any wall.

This will cause a fire hazard.

WARNING

18 L100001

Rise 1' Min.

VENT INSTALLATION

HORIZONTAL TERMINATION CONFIGURATIONS — RIGID VENTING

Since it is very important that the venting system maintain its balance between the combustion air intake and the ue gas

exhaust, certain limitations as to vent congurations apply and must be strictly adhered to.

The Vent Graph, showing the relationship between vertical and horizontal side wall venting, will help to determine the various

dimensions allowable. See page 16.

Minimum clearance between vent pipes and combustible materials is 3" on top and 1" from bottom and sides unless

otherwise noted.

When vent termination exits through foundations less than 20" below siding outcrop, the vent pipe must ush up with the sid-

ing.

It is best to locate the replace in such a way that minimizes the number of offsets and horizontal vent length.

The horizontal vent run refers to the total length of vent pipe from the ue collar of the replace (or the top of the Transition

Elbow) to the face of the outer wall.

Figure 18 - Maximum Three (3) 90 Elbows

Per Installation

The maximum number of 90° elbows per side wall installation is three (3), the maximum horizontal run is 20" (Figures 18, 19).

Figure 19 - Maximum Horizontal Run with 1 foot rise

3 x 90°

Elbows

20"

Max.

The Commonwealth of Massachusetts requires the installation and USE of Carbon Monoxide detectors

in the rooms of ALL direct vent units which utilize a SIDE WALL VENTING TERMINATION

FOR STATE OF MASSACHUSETTS:

20"

Max

L100001 21

7'6"

A B

• If a 90° elbow is used in the horizontal vent run (level height

maintained) the horizontal vent length is reduced by 36" (914

mm) (Fig. 21 A and B) This does not apply if the 90° elbows

are used to increase or redirect a vertical rise. See Figure 19.

Example: According to the vent graph (page 16) the maximum

horizontal vent length in a system with a 7.5' vertical rise is 20’

and if a 90° elbow is required in the horizontal vent it must

be reduced to 17'.

In Figures 20 and 21, Dimension A plus B must not be greater

• The maximum number of 45° elbows permitted per side wall

installation is two (2). These elbows can be installed in either

the vertical or horizontal run.

• For each 45° elbow installed in the horizontal run, the length

of the horizontal run MUST be reduced by 18" (45cm). This

does not apply if the 45° elbows are installed on the vertical

part of the vent system.

• The maximum number of elbow degrees in a system is 270°.

See Figure 22.

Figure 21 - Maximum Vent Run with Elbows

Figure 20 - Horizontal Run Reduction

Figure 22 - Maximum Elbow Usage

VENT INSTALLATION

90°

90° Elbow = 3'

1 + 2 + 3 = 180°

7'6"

HORIZONTAL TERMINATION CONFIGURATION —

RIGID VENTING (Continued)

Example: Elbow 1 = 90°

Elbow 2 = 45°

Elbow 3 = 45°

Elbow 4 = 90°

Total Angular Variation = 270°

than 17' (5.18 m).

A + B =

7' Maximum

Page is loading ...

Woodbridge Fireplace Inc NEWPORT-P Installation And Operating Instructions Manual

Brand: Woodbridge Fireplace Inc

Model: NEWPORT-P

Category: Fireplaces

Type: Installation And Operating Instructions Manual

This manual is also suitable for

Download PDF

report

Woodbridge Fireplace Inc NEWPORT-P Installation And Operating Instructions Manual

This manual is also suitable for

Woodbridge Fireplace Inc NEWPORT-P Installation And Operating Instructions Manual

Related papers

Other documents