Planar PD8130 Installation guide
- Category
- Projection lenses
- Type
- Installation guide
020-0960-00 Rev. B 1
PRELIMINARY
The PD8130/PD8150 is shipped with the standard (1.85:1 to 2.40:1) projection
lens pre-installed. If your installation requires the optional short-throw (1.56:1 to
1.86:1) lens, proceed as follows to remove the standard lens and replace it with
the short-throw lens.
1. Using a Phillips screwdriver,
remove the two screws holding
the projector front cover in place.
2. Gently pull the cover away from
the projector at each side to
detach it.
3. Remove the cover and set it aside.
1. PD8130/PD8150 Short-Throw
Lens
Planar Systems, Inc.
1195 NW Compton Drive
Beaverton, OR 97006-1992
+1 (866) PLANAR1
www.planarhometheater.com
Part Number 997-5351-00
Installation Instructions
PD8130/PD8150 Short-Throw Lens
2 020-0960-00 Rev. B
PRELIMINARY
Removing the Stray Light
Shield
4. Remove the center top and center bottom Phillips screws securing the left
and right halves of the light shield to each other.
5. Remove the two Phillips screws holding the left half of the shield in place.
Then, lift it off and set it aside.
6. Repeat Step 5 to remove the right half of the stray light shield.
➤
020-0960-00 Rev. B 3
PRELIMINARY
Removing the Standard
Lens
7. Remove the foam shield around the front of the lens and set it aside. (You
will install it on the replacement lens later.)
8. Remove the two (2), black plastic retaining clips on either side of the lens.
Each clip is held in place with two (2), captive Phillips screws. The white,
plastic standoffs serve as “handles” to make removing the clips easier.
9. Carefully remove the lens from the lens cavity by pulling it straight out, then
tilt it upward to allow the vertical lens shift adjuster to clear the opening at
the front of the projector.
PD8130/PD8150 Short-Throw Lens
4 020-0960-00 Rev. B
PRELIMINARY
Installing the Short-Throw
Lens and Re-Assembling
the Projector
10. Remove the vertical lens shift adjuster from the
top of the lens assembly that you just removed.
Install it at the same location on the
replacement lens assembly.
Note carefully the correct orientation of the lens when doing this. When
oriented correctly, the notch on the lens mounting plate faces down. The
lens aperture is crescent-shaped, with the concave edge facing down and
to the left:
11. Insert the short-throw lens into the lens
cavity. Ensure that the notch on the
vertical lens shift adjuster mates with
the retaining slot on the projector, as
shown at right. Otherwise, the adjuster
won’t work correctly.
12. Secure the lens in place using the black retaining clips that you removed in
Step 8.
13. Install the foam lens shield around the new lens (refer to Step 7).
14. Replace the stray light shield that you removed in Steps 4 through 6.
(Remember to reconnect the black wire to the shield.)
15. Replace the projector front cover that you removed in Steps 1 through 3.
➤
Vertical
Lens Shift
Adjuster
Aperture
Notch on Lens
Mounting Plate
faces down
Incorrect Correct
-
1
-
2
-
3
-
4
Planar PD8130 Installation guide
- Category
- Projection lenses
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Planar Systems PD8150 Product information
-
Christie D4K35 User manual
-
Christie J series 2.4kW User manual
-
-
-
Christie DS+6K-M User manual
-
-
Christie Mirage HD14K-M User manual
-
-