innovair EIN18H2V32 Owner's manual

innovair
Brand
innovair
Model
EIN18H2V32
Category
Split-system air conditioners
Type
Owner's manual

This manual is also suitable for

HEAT PUMP
DUCTLESS SPLITS
REMOTE CONTROLLER
MANUAL
WARNING
• The information contained in the manual is intended for use by a qualified service technician
familiar with safety procedures and equipped with the proper tools and test instruments
• Installation or repairs made by unqualified persons can result in hazards to you and others.
• Failure to carefully read and follow all instructions in this manual can result in equipment
malfunction, property damage, personal injury and/or death.
• This service is only for service engineer to use.
EIN10H2V32
EIN13H2V32
EIN18H2V32
EIN24H2V32
www.innovair.com
8
9
10
11
12
13
14
ON / OFF Button
This button turns the air conditioner ON and
OFF.
FAN Button
Press to select fan speed (Ultra-Low, Low,
Low-Medium,Medium, Medium-High, High or
Turbo).
MODE Button
+ / - Button
Press to either raise or lower settings including
t
emperature and time.
TURBO Button
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temperatu-
re at cooling or heating operation in the shortest
time (if the indoor unit does not support this
function, there is no corresponding operation
happened when pressing this button.)
> AUTO —> LOW —> MED —> HIGH
> AUTO —> COOL —> DRY —> HEAT —> FAN
1
2
3
4
5
Fan speed indication
Modedisplay
Displayed when data transmitted.
Displayed when remote controller is ON.
Battery display(low battery detection)
Not available for this unit
Low speed
Medium speed
High speed
Auto fan speed
Displayed when TIMER ON time is set.
Displayed in Sleep Mode operation.
Displayed when TIMER OFF time is set.
Show set temperature or room
temperature, or time under TIMER setting.
INDICATORS ON LCD
AUTO
HEAT FAN
COOL DRY
6
Press to control horizontal angle of louvers and to
redirect airflow.
Button
7
Press to control horizontal angle of louvers and to
redirect airflow.
Button
CLOCK Button
TIMER ON/TIMER OFF Buttons
TEMP Button
Press to display time of day or time remaining
on timer.
Press to start or stop the timer. (Adjust with “+”
and “–” buttons.) See Owner's Manual for more
details.
Press to select temperature setting.
I FEEL Button
Press to activate; allows unit to sense tempera-
ture at the remote controller in Cool mode.
LIGHT Button
Press to turn on lights on the unit’s Front Panel
Display. Press again to turn off.
X-FAN Button
Automatically runs fan after unit is turned off to
remove moisture from coil.
QUIET Button
Press to activate in Heat or Cool mode; after the
room reaches its set temperature, the system
operates discreetly at Low fan speed.
15
SLEEP Button
Press to select one of three SLEEP modes, each
offering varying levels of comfort control while
sleeping. See Owner's Manual for more details.
1
31
15
14
6
3
7
11
2
5
4
8
10
13
9
12
4
2
EIN10H2V32
EIN13 2V32
EIN18H2V32
EIN24H2V32
WALL MOUNT DUCTLESS AIR CONDITIONING
ANDHEATING SYSTEM
NOTE: Please read the complete Owner’s
Manual carefully before operation.
H
www.innovair.com
www.innovair.com
KEY FEATURES & FUNCTIONS
SMARTPHONE CONTROL
Built-in intelligent WIFI
capability and Smart Control function allows you
to operate the unit with standard Android or iOS smartphones.
See Owner’s Manual for more details.
MULTI FAN SPEEDS
Whether operating in either Cool or Heat mode, the indoor fan can
be set to
your choice of seven different speeds
(Ultra-Low, Low,
Low-Medium, Medium, Medium-High, High or Turbo)
to achieve maximum comfort.
DRY MODE
During warm humid conditions, selecting this mode will increase moisture removal in your room for added indoor comfort. Fan speed
cannot be
adjusted in Dry Mode.
X-FAN MODE
In humid areas, this Dry Coil function allows indoor fan to run for a pre-determined time after unit is turned off (in Cool or
Dry modes) to
ensure that additional moisture is removed from coil.
POWER FAILURE FUNCTION
Your settings and parameters are stored in non-volatile memory and are retained during a power failure.
I FEEL MODE
This function senses the temperature at
the remote controller instead of at the indoor unit in Cool mode.
It then adjusts airflow and
temperature accordingly for the ultimate in personal comfort control and energy savings.
SLEEP MODE
Choose one of three selectable sleep cycles to automatically adjust room temperatures during your sleep time to maximize comfort and
reduce utility bills.
INTELLIGENT PRE-HEATING
In Heat mode, the system delays fan activation until the coil has warmed up to prevent blowing uncomfortable cool air into the room.
SELF-DIAGNOSIS
The built-in computer uses
real-time diagnostics to continuously scan for errors or malfunctions. Fault codes are shown on the unit display
to facilitate troubleshooting.
FAQs
Why does the fan continue to run even when the unit is not cooling or heating?
To maintain consistent temperatures and minimize energy-loss from constant starts and stops, the fan keeps air flowing past the thermostat.
What temperature is displayed on the remote controller?
The remote always displays your desired indoor temperature. (You may view current indoor temperature, as well as desired temperature, on
the indoor unit’s Front Panel Display.)
What happens if the remote is lost or damaged?
Use the Aux button to manually operate the unit. Lift up the front panel section on the indoor unit and locate the button on the right-hand side.
Press the button to turn the unit ON or OFF. (Not all functions will be available.) Press again to cancel Aux Mode and transfer control back to
the remote controller.
Not all features available on all models. Your actual system and related devices may differ from the images shown in this manual.
For complete instructions on these and other functions,
as well as important safety information, see the Owner’s Manual.
For more information, visit innovair.com.
Specifications are subject to change without notice. Manufacturer reserves the right to discontinue, or change at any time,
specifications or designs without notice or without incurring obligations.
©20
. All rights reserved. Innovair Corporation
w w w . i n n o v a i r . c o m
The design and specifications are subject to change without prior notice for
product improvement. Consult with the sales agency or manufacturer for details.
Any updates to the manual will be uploaded to the service website, please check
for the latest version.
66129936368
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

innovair EIN18H2V32 Owner's manual

innovair
Brand
innovair
Model
EIN18H2V32
Category
Split-system air conditioners
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents