Renew Health Zensor device V1 Start Manual

Brand: Renew Health

Model: Zensor device V1

Type: Start Manual

Start Guide

DETERMINE PATCH LOCATION

 � Plan position of where patches will be placed before

removing the liners.

� The patches should only be placed on healthy, dry skin.

:10

sec

SKIN PREPARATION

�Inspect the area to ensure the skin is:

�Intact

�Hairless

�If required, remove chest hair.

�If required, clean skin using soap and water.

�Allow skin to dry completely.

APPLYING ZENSOR™ PATCHES

�Remove the patch liners to expose the adhesive.

�Place patches in the recommended position.

�Press rmly across each patch for 10 seconds.

�If required, coil and tape the excess wire to the skin.

ATTACH ZENSOR™ UNIT

�Give the BLUE button on your unit one quick press to turn it on. Make sure the

unit is showing a GREEN light before attaching it.

�Line up the unit studs with the magnetic studs on the patch.

�Connect the unit to the patch.

�Gently lift the edges of the unit to conrm all four connections are made.

�Try the ‘wriggle test’ - if you cannot move the unit around, you will know it is

properly attached.

EVERYTIME A SYMPTOM IS FELT

�Press the BLUE button once.

�Remain still for 30 seconds while your heart rhythm is recorded.

Electrode Array

RA electrode patch label LA electrode patch label Lower left electrode patch label

RA electrode patch label

LA electrode patch label

Lower left electrode patch label

The Zensor™ system is not intended to be used to summon emergency care.

:10

sec

WHEN SHOWERING

�Detach the unit from the body.

�Turn the unit off by holding down the

BLUE button rmly and the lights turn

off.

�Remove the battery from the unit.

(Step 7a)

�Switch on the charger.

�Insert battery into charger. The battery

will click into place when correctly

aligned. (Step 7b)

�Check that the light on the battery

charger is ORANGE to indicate

charging. The light will change to

GREEN when the battery is fully

charged.

�Slide the other fully charged battery

into the unit.

�Turn on the unit.

�Return the unit to the magnetic stud

patch on the body.

RETURN ZENSOR™ DEVICE KIT TO YOUR DOCTOR

�Press and hold the BLUE button until the lights turn off. (Step 8a)

�Ensure the unit, batteries, charging cables etc. are placed back in the

case and bring back to your prescribing doctor. (Step 8b)

PN 1414 Rev A

CHANGING BATTERIES ON THE ZENSOR™ UNIT

If you require any further assistance in relation to the system or wish to

report an unexpected operation or event, please contact your healthcare

provider.

�Remove the unit from the patches.

�Keep patches on the body.

�Shower for a short period

(5 minutes) only.

�Keep your back to the shower as

much as possible.

�Keep soaps/shampoo away from the

patches.

�Dry the patches with a gentle

‘patting’ motion.

�Return the unit to the magnetic

stud patch.

Healthcare Provider Contact Details:

0120

Intelesens Ltd,

17 Heron Road,

Belfast, BT3 9LE,

N. Ireland, UK

Renew Health Ltd,

IDA Business & Technology Park, Garrycastle,

Dublin Rd, Athlone, Co Westmeath,

N37 F786, Ireland

Manufactured by: For:

BATTERY INFORMATION

No sound Normal operation

No sound Intermittently goes on and off - no action required



Flash Repeated Long Beep Critically low battery - CHANGE BATTERY

Flash Repeated Short Beep Error indication*

* This indication may last approximately 6 seconds. If error exists after 6 seconds, turn off the device and

remove the battery. Reinsert the battery and switch the unit on. If error persists, contact your physician.

Renew Health Zensor device V1 Start Manual

Brand: Renew Health

Model: Zensor device V1

Type: Start Manual

Download PDF

report

Renew Health Zensor device V1 Start Manual

Renew Health Zensor device V1 Start Manual

Other documents